Tripp Lite B119-4X4 video switch
Contents
1. On _ i S HDMI Matrix Switch Models B119 2X2 B119 4X4 Package Contents Product Features Mounting Standard Installation RS 232 Serial Control Troubleshooting oO Oo A WN N Warranty amp Warranty Registration 10 Excellence TRIPP LITE 1111 W 35th Street Chicago IL 60609 www tripplite com support Copyright 2013 Tripp Lite All rights reserved 1 13 08 038 9332BC indd 1 8 5 2013 12 26 35 PM Package Contents e B119 2X2 or B119 A4X4 Local Transmitter Unit External Power Supply Input 100 240V 50 60Hz 0 5A Output 5V 2A 3 5 mm to DB9 Adapter Cable Mounting Hardware e Remote Control Owner s Manual The B119 4X4 comes with a 5V 3A power supply Product Features e Share multiple HDMI sources between multiple monitors Allows any input to be routed to any output or the same input to be routed to multiple outputs Switch between inputs via pushbuttons remote control or RS 232 serial Monitors can be located up to 25 ft from the switch Supports video resolutions up to 1080p 60Hz HDCP and EDID compatible Mounting hardware included Plug and play No software or drivers required Compatible with all operating systems Compliant with the Federal Trade Agreements Act TAA for GSA Schedule purchases Optional Accessories P568 Series High Speed HDMI Cables e P520 006 RS 232 Serial Extension Cable 13 08 038 9332BC indd 2 8 5 2018 12 26 35 PM The B119 2X2 an2. SUCH DAMAGE Specifically TRIPP LITE is not liable for any costs such as lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data costs of substitutes claims by third parties or otherwise WARRANTY REGISTRATION Visit www tripplite com warranty today to register the warranty for your new Tripp Lite product You ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product No purchase necessary Void where prohibited Some restrictions apply See website for details FCC Notice Class B This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television rec
3. manual 13 08 038 9332BC indd 9 8 5 2013 12 26 38 PM Warranty amp Warranty Registration 1 Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one 1 year from the date of initial purchase TRIPP LITE s obligation under this warranty is limited to repairing or replacing at its sole option any such defective products To obtain service under this warranty you must obtain a Returned Material Authorization RMA number from TRIPP LITE or an authorized TRIPP LITE service center Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase This warranty does not apply to equipment which has been damaged by accident negligence or misapplication or has been altered or modified in any way EXCEPT AS PROVIDED HEREIN TRIPP LITE MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not permit limitation or exclusion of implied warranties therefore the aforesaid limitation s or exclusion s may not apply to the purchaser EXCEPT AS PROVIDED ABOVE IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF
4. on controlling the switch using Terminal Emulation Software 13 08 038 9332BC indd 5 8 5 2018 12 26 37 PM RS 232 Serial Control Before using RS 232 Serial Control you must first go into your Terminal Emulation Software and update the COM port settings Go to the Setup drop down menu and select the Serial Port option i Bn re erat Ma e Window Kanjicode Help Serial port Proxy SSH SSH Authentication SSH Forwarding SSH KeyGenerator TCP IP General Recurring command ViewMode password Additional settings Save setup Restore setup Load key map 2 Select the COM port that is being used and update the remaining settings as follows Baud Rate 57600 Data 8 bit Parity none Stop 1 bit Flow Control none Serial port setup Port Baud rate Data Parity Stop Elow control Transmit delay 0 msecjchar 0 msec line 13 08 038 9332BC indd 6 8 5 2018 12 26 38 PM RS 232 Serial Control 3 Next you will need to configure your software to allow input control Go to the Setup drop down menu and select the Terminal option IF Window Font Keyboard cs samt ash Proxy SSH SSH Authentication SSH Forwarding SSH KeyGenerator TCP IP General Recurring command ViewMode password Additional settings Save setup Restore setup Load key map n Update the following settings Receive LF
5. Local Echo enable The remaining settings can stay as they are Terminal size New line CN 98 x 39 Receive 7 Term size win size Transmit CR L Auto window resize Terminal ID Coen echo Help Answerback l Auto switch VTX TEK Kanji receive Kanji transmit UTF 8 UTF 8 Kanji in B Zbit katakana Tbit katakana Kanji out AB locale japanese E CodePage 932 m 13 08 038 9332BC indd 7 8 5 2018 12 26 38 PM RS 232 Serial Control E Once these settings are updated the Terminal Emulation Software will recognize the switch allowing you to enter commands to control it with The following table lists the available commands Switches the source being displayed on the selected output x is the output 1 2 3 or 4 and n is the desired source A B C or D For example a command of sw1 2 would display source 2 on output 1 Turns power to the switch on off STE Displays the current output state showing which source is being displayed on each output 13 08 038 9332BC indd 8 8 5 2018 12 26 38 PM Troubleshooting If you are unable to get an acceptable image after following the installation instructions try the troubleshooting tips below Is the external power supply that came with the product connected and plugged into a working power source For the product to function properly it must be connected to and receiving power from the external power supply E Was th
6. d B119 4X4 come with mounting hardware that allows them to be mounted in a variety of ways The following images show the different ways the included mounting brackets can be attached for different mounting methods Note The images below show a B126 1A1 HDMI over Cat5 Receiver Unit but the mounting hardware installation is the same for the B119 2X2 and B119 4X4 Wallmount 1 Wallmount 2 TRIPP LITE HDMI OVER Cat5 EXTENDER REMOTE UNIT MODEL B126 1A1 Pole Mount EAE s Q m iz m c 15 2m ERE 5 o 1 9 a la 13 08 038 9332BC indd 3 8 5 2013 12 26 36 PM Standard Installation Note 1 The diagram below shows a B119 2X2 installation but installation will be the same for the B119 4X4 except for the number of ports 2 The back panel of the B119 4X4 contains an IR port which has been capped off This port is intended for future use and does not currently function B119 2x2 Optional Blu Ray Up to 16 ft Up to 25 ft Up to 16 ft Up to 25 ft Make sure all devices being connected are turned off 2 Optional Connect the 3 5 mm to DB9 adapter to the RS 232 serial port on the switch and then to the DB9 serial port on the computer you will be using to control it with El Connect the first HDMI source to the port on the switch marked Source A Note The HDMI cable connecting the source to the switch must be no longer than 16 ft n Repea
7. e power to the connected devices turned off prior to installation If not restart them El what type of cabling are you using Inferior cabling can result in poor performance so it is important that you use cables that can support the video resolution you are trying to obtain It is recommended that you use Tripp Lite s P568 Series High Speed HDMI cables as they have been tested to work with the B119 Series Matrix Switch products n Test your cables to ensure they are working properly For example connect your HDMI cables between a source and monitor that you know works to see if the cable is functioning E i5 the switch located in an area that exposes it to higher temperatures If the product is overheated it will not function properly 6 What length HDMI cable are you using The cable connecting a HDMI source to the switch must be no longer than 16 ft in length The cable connecting the switch to a display must be no longer than 25 ft in length If you are having trouble getting your Terminal Emulation Software to recognize the switch you may need to shut down your installation and start from the beginning The 3 5 mm to DB9 adapter cable must be connected first otherwise the switch will not be recognized El you are still having trouble getting your Terminal Emulation Software to recognize the switch check to make sure that your serial settings are set according to the instructions in the RS 232 Serial Control section of this
8. eption which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the user s authority to operate this equipment 10 13 08 038 9332BC indd 10 8 5 2018 12 26 38 PM Warranty amp Warranty Registration WEEE Compliance Information for Tripp Lite Customers and Recyclers European Union Under the Waste Electrical and Electronic Equipment WEEE Directive and implementing regulations when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to e Send old equipment for recycling on a one for one like for like basis this varies depending on the country e Send the new equipment back for recycling when this ultimately becomes waste WARNING Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended Do not use this equipment in the presence of a flammable ane
9. sthetic mixture with air oxygen or nitrous oxide Tripp Lite follows a policy of continuous improvement Product specifications are subject to change without notice 11 13 08 038 9332BC indd 11 8 5 2018 12 26 38 PM Excellence TRIP p LI TE D 1111 W 35th Street Chicago IL 60609 www tripplite com support 12 13 08 038 93 32BC_revB 13 08 038 9332BC indd 12 8 5 2013 12 26 38 PM
10. t step 3 to connect additional HDMI sources to the remaining ports 5 Connect the external power supply to the switch and plug it into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS When receiving power the following LEDs will illuminate The Green Power LED and Orange Source LEDs for the Source ports that have devices connected to them A Green LED will also illuminate to indicate the source that is being transmitted to each Output port 4 13 08 038 9332BC indd 4 8 5 2013 12 26 37 PM Standard Installation G Connect the first HDMI display to the port on the switch marked Output 1 Note The HDMI cable connecting the switch to a display must be no longer than 25 ft Repeat step 6 to connect additional displays to the remaining ports turn on the power to the connected devices The video image should now be displayed on the connected monitors E Press the switch next to each set of Output LEDs to switch the source being displayed on the corresponding Output monitor You can also use the included remote control to switch between sources As with the switch next to the Output LEDs press the button on the remote control of the desired Output port to switch the source being displayed Note The same 4 button remote control comes with both the B119 2X2 and B119 4X4 Buttons 3 and 4 will not be used for the B119 2X2 See the RS 232 Serial Control section in this manual for details
Download Pdf Manuals
Related Search