Hunter 52" Sonic
Contents
1. Table of Contents www HunterFan com 1 888 830 1326 Congratulations on purchasing What to Expect with your new Hunter ceiling fan It will Your Installation Tools Needed Mounting Options Ceiling Bracket provide comfort and performance ETA in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to iri Blades supply you with the best ceiling fan available anywhere in the world To register your fan please visit www HunterFan com register Save your receipt for proof of purchase Operation Light Kit Maintenance amp Cleaning Troubleshooting M3551 01 10 28 13 Hunter Fan Company What to Expect with Your Installation Must be able to secure the fan to building structure or fan rated outlet box You may need a friend to help you Check box to see fan weight If you are unfamiliar with wiring use a qualified electrician D Know your wiring Ceiling angles greater than 34 will require an Angled Mounting Kit See page 4 for details a Assess ceiling angle 30 inches from blade tip to nearest wall or obstruction 7 feet from bottom edge of blade to the floor A Assess location Standard Downrod for ceilings 8 10 feet high 2 Lo2. B digital device pursuant to part 15 of the FCC Rules These limits are to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Tools Needed www HunterFan com 1 888 830 1326 a amp L Ladder LI Pliers a Wire Strippers lf Screwdrivers If you are installing multiple remote controlled fans on the same circuit breaker you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls Go to www HunterFan com FAQs and click How do properly install multiple remote controlled fans for more information Power Drill 9 64 Drill Bit optional optional If mounting to a support structure you will also need these tools M3551 01 10 28 13 Hunter Fan Company 3 4 CEILING a P Mounting Options www HunterFan com 1 866 268 1936 f ka ea a ra ka ea ra a ra e o N o o O a egoe U s If you have a flat ceiling Hang your fan by a standard downrod included Standard Support Support Mounting Structure T O If you have an angled ceiling InN 0 1 You will need a longer downrod sold separately Outlet Box 2 If your ceiling ang
3. de assembly screws found in the A hardware bag M3551 01 10 28 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Light Kit Light Kit Assembly Screw Partially install two of the light kit assembly Align the keyholes in the light kit ring with the screws found in the hardware bag partially installed screws Lift the light kit ring in place and rotate counterclockwise to situate the screws in the narrow ends of the keyholes M3551 01 10 28 13 Hunter Fan Company www HunterFan com 1 888 830 1326 amp Insert the third screw found in the hardware bag into place and then tighten all three 3 screws Make sure the light kit ring is securely attached Failure to properly secure all three assembly screws could result in the light fixture falling Light Kit continued www HunterFan com 1 888 830 1326 Install the included 18W CFL Position the notches in the outer Carefully lift the globe up inside bulb When necessary replace rim of the globe so they line up the light fixture as far as it will go with bulbs of same wattage with the tabs on the light kit ring Rotate the globe in a clockwise direction until it is held tightly in place by the three tabs See next page for fan operation instructions M3551 01 10 28 13 Hunter Fan Company Operation Maintenance amp Cleaning Battery Door Phillips Head Screw To access the battery compartment remove th
4. e saving energy and money while protecting the environment by purchasing this ENERGY STAR qualified Hunter ceiling fan With this purchase you are doing your part to protect the environment In 2010 ENERGY STAR qualified ceiling fans are projected to cut air pollution by more than 500 million pounds Your new ceiling fan has earned the ENERGY STAR label because it meets high energy efficiency specifications set by the Environmental Protection Agency EPA ENERGY STAR labeled ceiling fans save energy because they have more efficient fan motors and air delivery due to more aerodynamic blade configurations Ceiling fan models bearing the ENERGY STAR label move air 14 20 more efficiently than typical ceiling fan models For more information on ENERGY STAR visit www energystar gov
5. e small Phillips head screw that secures the battery door to the transmitter assembly The battery should be installed with the positive side up Replace with a CR2032 battery when necessary Turn Power ON To turn on fan press a fan speed button Speeds range from off 0 to high 3 Quickly press the Light Note The remote must be paired before the fan will operate Within 3 minutes of restoring power to the fan press both the Fan Off button and the High button for at least 4 seconds Your fan will turn on low to indicate successful syncing If it does not turn off power to your fan wait 1 minute then try again If using the transmitter with multiple fans repeat this process for each fan M3551 01 10 28 13 Hunter Fan Company button to turn the lights off and on www HunterFan com 1 888 830 1326 switch Cover Plate Removed Tabs To install the transmitter cradle remove the two screws holding the switch cover plate Do not remove the cover plate Orient the cradle by lining up the two mounting holes with those on the cover plate Insert and tighten the screws Do not over tighten Note For rocker style cover plates break off the tabs by pushing outward Operation Maintenance amp Cleaning continued Safe Exit The Safe Exit Program gives you about thirty seconds of light when you turn the lights of
6. f to exit the room before the lights go out To use Safe Exit e Press the Fan Off button for at least three seconds to initiate the Safe Exit Mode e The lights will flash for visual confirmation e The lights will stay on 50 brightness for 15 seconds and then begin to dim After a total of 30 seconds the lights will be completely off Note For CFL lighting the lights will stay on 100 brightness for 30 seconds After a total of 30 seconds the lights will be completely off Reverse Switch To switch the direction of air flow move the reverse switch to the opposite position You will need to remove the light kit glass to do so M3551 01 10 28 13 Hunter Fan Company www HunterFan com 1 888 830 1326 For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning products may damage the finishes Troubleshooting Fan doesn t work Make sure power switch is on Push the motor reversing switch firmly left or right to ensure that it is engaged Check the circuit breaker to ensure the power is turned on Make sure the blades spin freely Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on page 7 Check the plug connection in the switch housing Remote control of fan is erratic Make sure the battery is installed correctly Install a fresh battery Transmitter only works when held a
7. le is greater than 34 you will Angled Ceilin required also need an Angled Mounting Kit sold separately Mounting N Outlet e required Mounting Use the three steps below to determine if your ceiling angle is greater than 34 Use Standard Mounting Use Angled Mounting to hang the fan from a flat ceiling to hang the fan from a vaulted or angled ceiling Guide Touches BOTH Ceiling amp Wall You need ONLY a Longer Downrod most common Mounting Kit M3551 01 10 28 13 Hunter Fan Company Ceiling Bracket 4 aaa For angled ceilings point opening toward peak Make sure all four bumpers are still attached If you are unable to do this call Technical Support at 1 888 830 1326 Refer to warning w 1 on pg 2 Use wood screws included when securing to support structure with approved electrical outlet box Drill 9 64 pilot holes in support structure to aid in securing ceiling bracket with hardware found in the hardware bag M3551 01 10 28 13 Hunter Fan Company i www HunterFan eom 1 888 830 1326 Use machine screws provided with outlet box when securing to existing ceiling fan rated outlet box Make sure it is securely installed and is acceptable for fan support of 31 8 kg 70 Ibs or less To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box a
8. led wire terminator JNO UOWWOD d IYM Using an orange wire connector from the W hardware bag connect the black wire ungrounded from the ceiling to the black wire from the receiver marked live in Connect the white wire grounded from the ceiling to the white wire from the receiver marked neutral in or common in papunosb y ym papunosbun y2ejq UI J21 NDU PyM A Q Om RECEN Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box M3551 01 10 28 13 Hunter Fan Company www HunterFan com 1 888 830 1326 r A HT E TUH Position the canopy so that when Lift the canopy into place so that Insert the two canopy screws lifted into place the canopy fits into the screw holes are aligned found in the hardware bag the hanging bracket as shown Note Fan style may vary f M3551 01 10 28 13 Hunter Fan Company Blades Insert a blade into the motor housing Your blades are shielded with Dust Armor which is ananotechnology coating that repels dust For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning agents may damage the finishes Attach each blade to the fan using two blade grommets found in the W hardware bag and two bla
9. nger Downrod for ceilings 10 feet or higher a Select a downrod length 2 M3551 01 10 28 13 Hunter Fan Company www HunterFan com 1 888 830 1326 D Read and Save These Instructions This product conforms to UL Standard 507 A WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Hunter Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Hunter replacement parts This equipment has been tested and found to comply with the limits for a Class
10. ssociated with the wall switch location Downrod www HunterFan com 1 888 830 1326 T U YN O 1 O The wires can be cut but Put the wires and downrod through leave at least 8 extending the canopy Let the canopy sit from the top of the downrod loosely on top of the fan DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES Place the downrod ball into the slot in the ceiling bracket as 8 4 M3551 01 10 28 13 Hunter Fan Company pi l www HunterFan com 1 888 830 1326 Note To connect the wires Buipuno16 ads mo j u 16 green yellow stripe Using an orange wire connector from the W hardware bag connect the 3 grounding wires green green yellow stripe or bare copper coming from the ceiling downrod and hanging bracket Q Q D D 5 SN lt n ot D D Refer to CAUTION c 1 on pg 2 hold the bare metal leads together and place a wire connector over them then twist clockwise until tight Using the blue wire connectors from the remote control hardware bag connect the white wire from the receiver marked common out to the white wire from fan Connect the black wire from the receiver marked fan out to the black wire from the fan Connect the blue wire from the receiver marked light out to the blue wire from the fan The red wire from the receiver will not be used it has a pre instal
11. t close range Install a fresh battery Excessive wobbling e Tighten all of the blade and blade iron screws until they are snug Use the provided balancing kit and instructions to balance the fan Noisy Operation e Tighten the blade and blade iron screws until they are snug e Check to see if any of the blades are cracked If so replace all of the blades If you have multiple remotes or multiple remote controlled fans installed on the same circuit breaker and you are experiencing interference or faulty operation of your remote controls please go to www HunterFan com FAQs and click How do properly install multiple remote controlled fans for information on how to correct this issue M3551 01 10 28 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Hunter fans have the power to cut your cooling costs up to 40 Beat the High Cost of Cooling The air movement created by a Hunter ceiling fan lets you set your thermostat higher and still stay comfortable Every degree you raise the thermostat saves up to 7 on energy costs So you can cut back on expensive air conditioning and save up to 40 on cooling In winter your Hunter fan recirculates warm air and saves up to 10 on heating bills On average at low speed settings Your savings may vary based on climate building type and thermostat setting Save Energy and Money While Protecting the Environment Congratulations You r
Download Pdf Manuals
Related Search