zBoost SOHO MAX
Contents
1. Maximum Performance Minimum Performance Additional Cable Requirements RG 6 cable is used to connect the External Antenna and the Base Unit Should you need additional cable length 15 foot extensions Part YX030 15w are available at www zBoost com The total cable length should not exceed 65 feet unless you also purchase an upgraded signal antenna see page v A longer cable is helpful only if it allows you to place the External Antenna in a location where you measure stronger signal Avoid placing the External Antenna near metal such as wiring A C ducts metal siding truss plates etc When connecting the cable to the antenna run the cable straight down from the antenna Avoid draping the coax near the antenna Grounding the External Antenna If you decide to place the External Antenna outdoors it must be properly grounded See page v for a recommended grounding kit The set up must be in accordance with Article 810 of the National Electric Code NEC A listed antenna discharge unit must be provided for the lead in coaxial cable per NEC article 8 10 20 or the shield of the coaxial cable must be permanently and effectively grounded in accordance with NEC article 8 10 21 Please consult a professional installer or electrician for more information zBoost Max ZB545M Manual Securing Cable with a Drip Loop Exterior aie If you place the External Antenna outdoors create a drip loop wi2. 15 of vertical separation Cell phone signal bars are approximate and vary from phone to phone The number of bars can fluctuate widely depending on the location of the phone the position or angle of the phone weather etc Most cell phone signal meters update every 6 to 10 seconds An increase of only one bar typically indicates a 4x to 10x signal increase THE BEST INDICATOR OF PRODUCT PERFORMANCE IS THE ABILITY TO RELIABLY PLACE AND RECEIVE CALLS WHERE YOU COULD NOT BEFORE zBoost Max ZB545M Manual Antenna Bracket Assembly IMPORTANT Incorrectly mounting the External Antenna to the mounting bracket see figure A will impede performance Ensure that the External Antenna is properly positioned in the mounting bracket as pictured To mount External Antenna to a pole Attach antenna to pole bracket as pictured Use U Bolt to secure bracket to pole and fasten DO NOT mount to a metal pole To mount External Antenna to a flat surface Attach antenna to pole bracket as pictured Secure bracket to desired surface using provided screws Use of the Saddle and U Bolt are not necessary for this option SECOND Position the Base Unit Connect the Indoor Antenna to the Base Unit and place it where you need signal For the widest possible signal area position the Base Unit near the middle of a room You may also mount it on an interior wall by first removing the bracket screwing the bracket to a wall scre
3. Because some jurisdictions do not allow limitations on how long an implied warranty last or the exclusion or limitation of liability for consequential or incidental damages the above limitations may not apply to you For full warranty guidelines see page 12 Changes or modifications not expressly approved by zBoost could void the user s authority to operate this equipment and or void the product warranty zBoost Max ZB545M Manual Package Contents Before you begin make sure all of the following parts came with your zBoost Max ZB545M Contents SETUP ovenvew Setup overview zBoost Base Unit Indoor Antenna Power Supply 15 feet of RG 6 Cable Window Entry Cable Go 35 feet of RG 6 Coax Cable External Antenna and Mounting Hardware zBoost Max ZB545M Manual Accessories The following accessories are authorized for this zBoost product Please see our website for complete selection To order call 1 800 871 1612 or visit www zBoost com Broadcast Antennas Indoor CANT 0032 Indoor Broadcast Antenna Omni Whip Direct to Booster Black CEL PCS 1 dBi CANT 0034 Indoor Broadcast Antenna Omni Whip Direct to Booster White CEL PCS 1 dBi CANT 0039 Indoor Broadcast Antenna Omni Whip Direct to Booster Black Wide Band LTE CEL AWS PCS 1 dBi YX027 F Indoor Broadcast Antenna Directional Panel w F Female Connector CEL PCS 6 8 dBi YX052 Indoor Broadcast Antenna Wide Band Cei
4. Uplink 19 dBm Downlink 4 dBm Cellular band Frequency Uplink 824 to 849 MHz Downlink 869 to 894 MHz CEL band supported A B A B CDMA GSM GPRS EDGE EVDO 1xRTT UMTS HSPA 3G Uplink 21 dBm Downlink 4 dBm 3W standby 7W max signal 5 0VDC 2 0A Max Base Unit Size and Weight 5 x 7 x 1 25 9 oz Operating Conditions Indoor Use Only 40 105 F Coverage area Up to 3 500 sq ft The Manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present the rating would have to be reduced by 3 5 dB especially where the output signal is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device This product is covered by patent US 7 706 744 Other U S and foreign patents pending 10 zBoost Max ZB545M Manual Frequently Asked Questions What can expect my cell phone signal range and strength to be inside my home The closer you are to the base the stronger the signal This will vary with different conditions Some of the conditions that will affect the improved coverage area are signal strength outdoors the type of building materials in the home the placement of the unit and the antenna s proximity to cellular towers You can expect that your indoor coverage will be improved You wil
5. 2 1 05 Section 6 1 available or viewable at http Awww ic gc ca epic site smt gst nsf en sf08942e html Safety and Product Warranty Information Copyright Notice This manual is copyrighted All rights reserved This manual whole or in part may not be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form for distribution This manual whole or in part may not be modified without prior consent in writing from zBoost Copyright 2014 by zBoost Trademarks zBoost the zBoost logo Wireless Extenders Wi Ex the Wi Ex logo and Extending Cell Zones are registered trademarks of zBoost Safety Guidelines In accordance with FCC requirements of human exposure to radiofrequency fields the radiating element antenna shall be positioned such that a minimum separation distance of 8 inches 20cm is maintained between the radiating element and the user and or general population Limited Liability In no event shall zBoost be liable for any direct indirect special punitive incidental exemplary or consequential damages or any damages whether in an action under contract negligence or any other theory arising out of or in connection with the set up of use of inability to use or performance of the information services products and materials available from this manual These limitations shall apply notwithstanding any failure of essential purpose of any limited remedy
6. zBoost Max ZB545M Manual Table of Contents FCC Requir mentsiii2ss ain Aue ea ini eae ee ee i FCC Information vss sxia dictates aE NE Ea a a Eae aY ii Industry Canada Regulations ccccceeceecceeeeeeceeceeeeeeeeneaeeeeseeeaeaeeeeseeneeeeeeeeeneea ii Safety and Product Warranty Information cccccssseeeeeseeeeeeeseeeeeenseneeeneensneeeaees iii ele ne ue LEE iii Trademarks vsti wiki Hiaasen SA eid is Stace iii Safety Guidelines wrae eae eea a ae e aa EE aE E TeRi iii Limited Liability aea E EENE RA iii Package Contents cccccceccessneeseeeeeeeeeeeeeseeeeseeeeseseneeseseeeseseeeeeneesesseeesaseeeseneenensonanees iv INCCOSS E v Table of eu 1 OV RN WW sass sce os ge ce oe sees tna sas E Eea aeaaea a aE EA R RRS 2 Why Indoor Signals Can Be Weak erii niie ia aaa aN 2 Preparing to Set Up Your ZBoost Product cceecessneeeeeeeeeeeeeeeeseeeeeeeeeseeneeeeennneeenees 3 Additional Cable Requirement c ccccccceeeeeeee cece eeeeeeeeeeeeseeeeaeeeeeeseeneaeeeeseeeees 4 Grounding the External Antenn 4 Securing Cable with a Drip Loop 5 Ree EE 5 Setting Up Your zBoost Signal Booster cccceceeeee eee eeeseeeeeeeeeneeeeesseneeeseeneneeeees 5 FIRST Mount the External Antenna cccccceceeecceceeeeeeeeeeeeeseeeeaeeeeseseeaeeeeeeeeeaaes 5 Antenna Bracket ASSOMDIY 2 eccesseeeeeseceseccnenssneeestoneeeseeeeentanessecenteseenensnneneee 6 SECOND Position the Base Hm viaassiitiaieiie
7. ai zBoost extending cell zones zBoost Max ZB545M User Manual zBoost products have a 30 day money back guarantee when purchased directly from zBoost If product is purchased from a reseller or third party the purchaser is subject to the policies of the third party 1 Year manufacturer warranty Warranty registration at www zBoost com v 0314 zBoost Max ZB545M Manual FCC Requirements This is a CONSUMER Device BEFORE USE you MUST REGISTER THIS DEVICE with your wireless provider and have your provider s consent Most wireless providers consent to the use of signal boosters AT amp T Sprint T Mobile Verizon and 90 additional carriers have already given consent for all consumers to use this device Some providers may not consent to the use of this device on their network If you are unsure contact your provider You MUST operate this device with approved antennas and cables as specified by the manufacturer Antennas MUST be installed at least 20 cm 8 inches from any person You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider WARNING E911 location information may not be provided or may be inaccurate for calls served by using this device FCC contact information www fcc qov siqnal boosters registration Any product modifications that use unauthorized antennas cables and or coupling devices is no longer FCC compliant and will void the pro
8. at one time in my home will your product boost all of our signals simultaneously The zBoost Max is designed to cover multiple signals simultaneously and will allow multiple users to operate at the same time Does the zBoost work if you have no bars No if no signal is present outdoors zBoost products will not work for you Also keep in mind if your best signal is 1 bar at the External Antenna your coverage will be limited to a small room You could improve that with an upgraded antenna See page v 11 zBoost Max ZB545M Manual Warranty Information Limited 1 Year Warranty Warranty Registration at www zBoost com zBoost warrants every zBoost product to be free from defects in material and workmanship under normal use for the warranty period of one year Who Is Covered You must have proof of purchase to receive warranty service A sales receipt or other documentation showing the product purchased and the purchase date is considered proof of purchase This limited warranty extends only to the original consumer purchaser or any person receiving the product as a gift from the original consumer purchaser and to no other purchaser or transferee What is Covered Warranty coverage begins the day you purchase the product For one year from the original date the zBoost Cell Phone Signal Booster will be repaired or replaced with a new repaired refurbished or comparable product whichever is deemed necessary by zBoost if it beco
9. cable through a wall Connect the two provided RG 6 cables Then connect one end of the cable to the base of the External Antenna Run the coaxial cable along a descending pipe or through a wall that leads closest to the location of the Base Unit Connect the remaining end of the cable to the Base Unit Should you need additional cable length 15 foot extensions Part YX030 15w are available at www zBoost com Please note Cable longer than 65 feet is not recommended FOURTH Connect zBoost Base Unit to Power Connect the zBoost Base Unit to the power supply and plug into a power outlet When your zBoost system is in place and fully connected walk throughout your home and verify that you are able to reliably place calls If the signal strength has improved your zBoost is working Upon initial power up the LED will cycle RED GREEN and ORANGE for 30 seconds After 30 seconds a series of GREEN flashes will indicate the quality of your setup Following this a solid GREEN light indicates normal conditions If it is not solid GREEN follow the instructions in the Base Unit LED Indicators section Adjustments may be needed to optimize performance If you find the increased signal coverage is acceptable however no additional adjustments are needed See zBoost Base Unit Light Indicators on page 9 for more information External Antenna 7 ffs NX GA 28 et vertical separation U External Antenna SCH pie Power S
10. ccessory products are intended for resale and use as a single unit and such product kits are required to be sold to the end user or subsequent reseller as packaged The de kitting and sale as a standalone product of any one or more components of such a product kit is in violation of zBoost warranty No de kitted product will be eligible for return for any reason The sale of separate not kitted cable antennas and other accessories is allowed and fully warranted 12 zBoost Max ZB545M Manual Make sure you keep Please keep your sales receipt or other document showing proof of purchase Attach it to this User Manual and keep both nearby Also keep the original box and packing material in case you need to return your product Before requesting repair service If red light is on system is receiving signals from either the mobile device or the base station transceiver which are too strong for proper operation Please unplug your system Re orient your External Antenna and or Base Unit to reduce the excessive signal source Plug your system back in If still solid red call customer support 1 800 871 1612 To get warranty service Warranty service will be provided by zBoost If you believe you need service for your unit contact zBoost at 1 800 871 1612 or support zBoost com A representative will go through a diagnostic checklist with you If it is determined that the product needs to be returned for service or exchang
11. dinadiie aie denn Auli 6 THIRD R n the Coaxial Cable sirves cil aide ei EET eee 6 FOURTH Connect zBoost Base Unit to Power 7 Confirm That Your zBoost is Working Properly 0 ecceceeeseeesseeeeseeeeeneeeeeneeeenees 7 Improving Your Coverage Area ccccsseccsseceeeeeeeeseeeseseeaeeeeeneesneeesnseeaesnenneenneeeseeseaees 8 zBoost Base Unit Light Indicators ceseeeeeeseeeeeeeeeeeeeeeeesseeeeeeeeeeeneeeenseeseeseenenennees 9 Technical Specification cc cscisccccs cescassctescdsencecenessedeccecessndetacceaseteasecsenes sanecacesaxescaareds 10 Frequently Asked Questions ccccceeeceseneeeeeeneeeeeeeeesneeeeeseeeeeeseeseseneeeasoneeeasenennseeees 11 Warranty Information cccecesenceeeeeeeeeeceeeeseeeeeeeeeeesenneeeseeeeeeeeaeeeeneeeeseenseseeenensnneesnes 12 zBoost Max ZB545M Manual Thank you for choosing zBoost You will now be able to use your cell phone INSIDE your home Gone are the days when you had to go to the window upstairs or walk outside to use your cell phone Like a skylight that brings sunlight into your home zBoost transports and amplifies the outdoor signal into your home By following the easy instructions in this User Manual you will be Extending Cell Zones into your home Why Indoor Signals Can Be Weak There are several obstacles that can contribute to the poor reception you receive in your home 1 Location of the Cell Phone Tower in Relation to Your Home While cell phone p
12. duct warranty zBoost Max ZB545M Manual About zBoost zBoost a leader in cell phone signal boosters manufactures zBoost the award winning line of cell phone signal boosters that enhance the performance of your cell phone smartphone and wireless data card Compatibility Dual Band zBoosts are compatible with 800 MHz and 1900 MHz regardless of technology including CDMA and GSM Uses patented technologies and protects the carrier network 1 year manufacturer warranty Warranty registration at www zBoost com FCC Information FCC ID SO4ZB570 PCS CEL Warning Changes or modifications to this device not expressly approved by zBoost could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interfe
13. e reduced by 3 5 dB especially where the output is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and zBoost Max ZB545M Manual not by an attenuator at the output of the device Cet appareillage num rique de la classe B r pond a toutes les exigences de I interf rence canadienne causant des r glements d quipement L op ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interf rence nocive et 2 ce dispositif doit accepter n importe quelle interf rence re ue y compris l interf rence qui peut causer l op ration peu d sir e Le fabricant nominale de la puissance de sortie de ce mat riel est simple transporteur Pour les situations lorsque plusieurs signaux porteurs sont pr sents l valuation devrait tre r duite de 3 5 dB en particulier lorsque le signal de sortie est r mise et peut provoquer des interf rences adjacentes a la bande utilisateurs Ce pouvoir est de la r duction par le biais de la sortie d alimentation ou la r duction de gain et non par un att nuateur a la sortie du dispositif Please note This unit has been approved for use in Canada under RSS 131 however consent for the use of this device to improve cellular or PCS coverage must be obtained through your cellular or PCS provider prior to placing the unit in operation Please refer to the Industry Canada document CPC
14. ed you will receive a return merchandise authorization RMA number The representative will give you complete shipping details Do not return products to zBoost without a Return Authorization Number RMA To get out of warranty service To obtain out of warranty service contact zBoost at 1 800 871 1612 or support zBoost com for information on the possibility of any costs for repair or replacement of out of warranty products Reminder Record the model and serial number found on the product below Model Serial Purchase Date 13
15. ength in your attic or at roof level location where the signal will likely be stronger and where the External Antenna can be placed for best performance If you can reliably make and receive calls outside your home then zBoost can bring the signal into your home If only one signal bar is displayed on your cell phone outside indoor coverage will be limited to one small room We recommend placing the External Antenna outside and or purchasing a zBoost upgrade External Antenna for increased coverage see page v Cell phone signal bars are approximate and vary from phone to phone The number of bars can fluctuate widely depending on the location of the phone the position or angle of the phone weather etc Most cell phone signal meters update every 6 to 10 seconds An increase of only one bar typically indicates a 4x to 10x signal increase zBoost Max ZB545M Manual Before installing please note the following important factors in determining your zBoost performance At least 15 vertical feet is needed between the External Antenna receives the outside signal and the Indoor Antenna rebroadcasts the signal indoors Separation less than 15 vertical feet will result in decreased performance See illustration below Keep the External Antenna at least 3 feet above any metal See page 5 Setting Up Your zBoost Product for additional information 15 of vertical A separation
16. l be able to make calls where you couldn t before The degree of improvement will depend upon many factors The intent of zBoost products are to bring outside coverage inside Just as the signal bars move up and down when outside the boosted signal will fluctuate in a similar fashion Is a cellular phone signal booster the same as a wireless router will it help my WiFi signal The zBoost unit will not help your WiFi service This unit is designed to work with wireless PCS and Cellular phones and devices The WIFI in your home operates on a different frequency Why isn t my cell phone indicating more signal with more bars You may not always observe more bars that gain on your signal meter because of the signal spreading out from the antenna If your phone has a dB meter 3 dB is a significant increase of 2x 6 dB is 4x and 10 dB is 10x On a four bar phone one bar equals about 10 dB The increase in signal you will see depends upon The level of signal at the External Antenna outdoor The care of the antenna placement two feet away from metal adequate antenna separation 15 feet recommended The signal already present inside related to building losses The distance of your phone device from the Indoor Antenna signal spreads or diminishes rapidly with distance Also if your phone uses LTE it likely displays LTE signal level instead of 3G when a call is being placed There are usually several cell phones in use
17. ling Mount Omni w F Female Connector LTE CEL AWS PCS 1 2 dBi External Antennas Outdoor CANT 0028 Outdoor External Antenna Directional Low Profile Panel CEL AWS PCS 6 8 dBi CANT 0031 Window mount External Antenna for YX540 zBoost METRO Workspace Directional Panel CEL PCS 6 8 dBi CANT 0033 Outdoor External Antenna Small Omni CEL PCS 3 5 dBi CANT 0036 Outdoor External Antenna Omni with Industrial Casing CEL PCS 3 5 dBi CANT 0040 Outdoor External Antenna Wide Band Omni Directional LTE CEL AWS PCS 3 5 dBi CANT 0042 Outdoor External Antenna Wide Band Directional Log Periodic LTE CEL AWS PCS 10 12 dBi YX021 CEL Outdoor External Antenna Directional Panel CEL 8 dBi YX023 PCS Outdoor External Antenna Directional Panel PCS 13 dBi YX026 CEL Outdoor External Antenna Directional 3 foot Yagi with 12 Elements CEL 11 dBi YX039 PCS CEL Outdoor External Antenna Kit Two Directional Panels with Combiner CEL PCS 8 13 dBi Coax Cable To be used in addition to the cable included in your kit YX031 10W 10 Foot RG 8X Coaxial Cable with TNC Male amp Female Connectors Booster to Distribution Antenna YX031 100W 100 Foot Low Loss RG 11 Coaxial Cable with F Male Connectors Accessories YX012 Outdoor External Antenna Grounding Kit The FCC requires that this panel antenna has a minimum horizontal separation of 6 feet 2 meters from other CMRS commercial mobile radio service devices
18. mes defective or inoperative The exchange will be made without charge to you for parts and labor You will be responsible for the cost of shipping to the location designated by zBoost If zBoost cannot reasonably repair or replace the unit then zBoost may at its sole discretion refund the price you paid for the product or the price of the unit All products including replacement products are covered only for the original warranty period When the warranty on the original product expires the warranty on the replacement product also expires What is Excluded Your warranty does NOT cover e Labor charges for set up of the unit e Product replacement because of misuse accident lightning damage unauthorized repair or other cause not within the control of zBoost e Incidental or consequential damages resulting from the product Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you KR Any modifications or other changes to the product including but not limited to software or hardware modifications in any way other than as expressly authorized by zBoost will void this limited warranty e Product that has been modified or adapted to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of products damaged by these modifications All zBoost products that are packaged with other zBoost a
19. rence by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter In accordance with FCC requirements of human exposure to radiofrequency fields the radiating element antenna shall be installed such that a minimum separation distance of 20cm 8in is maintained from all persons Industry Canada Regulations IC ID 5544A ZB570PCSCEL This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The term IC before the radio certification number only signifies that Industry Canada technical specifications were met RF Exposure The manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present the rating would have to b
20. roviders have tried to place cell phone towers to provide the best overall coverage local ordinances and terrain features can impose restrictions on where these towers can be placed thus limiting the signal strength available at your location Obstructions Caused by Buildings Terrain and Trees Cell phone signals can be completely blocked or reflected by buildings walls trees hills and other terrain features resulting in low signal strength Energy Efficient Windows Energy efficient windows contain a metal film that can affect signal penetration into the house es D bh mm Tal Yanl Y wil Tel E zBoost Max ZB545M Manual Preparing to Set Up Your zBoost Product Tools Needed The following tools are needed to set up zBoost e 2 Phillips screwdriver e Cellular phone operating in the band supported by your zBoost unit e Drill may be required for outdoor or attic antenna placement Check for Signal Strength Before placing a zBoost in your home make sure that you can place calls on the outside of your home in the attic at roof level or wherever you plan to place the External Antenna zBoost can only bring signal into your home when signal reaches the External Antenna If there is no signal zBoost will not work for you Using your cell phone place a call from an outdoor location to confirm that enough signal is present to complete the call If a weak signal is available at ground level check the signal str
21. th the coaxial cable at the point where the cable enters the home through an outside wall This can be done by twisting and securing the cable into a loop no less than 4 across near the entry point This will help prevent moisture from gathering at entry point and leaking into the home Consult a professional installer if you need more information Wall Power Requirements The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the Included power supply The power supply consumes less than 10W less than 0 2A Setting Up Your zBoost Signal Booster FIRST Mount the External Antenna Choosing the best location for the External Antenna provides the best performance and the largest area of improved signal Choose a location for the External Antenna using your cell phone to determine the area of strongest signal typically found outside above the roofline or in an attic The antenna must also remain at least 3 feet from any metal objects such as pipes metal siding A C unit etc and at least 15 vertical feet above the Indoor SCH Antenna EES Identify the best location for attachment of the mounting bracket Maximum Performance such as an attic cross or main beam Secure the mounting bracket at the highest possible point Position the mounting bracket such that the External Antenna will be vertical and attach the External Antenna See Antenna Bracket Assembly on page 6 for more information
22. upply E H H H H Option 1 Running cable through Option 2 Running cable through a window a wall Confirm That Your zBoost is Working Properly When your zBoost system is in place and fully connected you should walk throughout the room and see that you are able to reliably place calls Remember coverage varies based on outdoor signal level home construction and antenna placement Coverage in adjoining rooms next to above or below will be reduced due to walls or ceiling floors zBoost Max ZB545M Manual Improving Your Coverage Area Should you desire to improve coverage you may e Relocate the External Antenna in order to capture a better signal higher is usually better and outside is better than inside e Increase the distance between the Indoor Antenna and the External Antenna e Purchase an upgrade antenna available at www zBoost com zBoost Base Unit Light Indicators zBoost Max ZB545M Manual During Initial Power Up once for every 2 dB less than Light Mode Status Solution Cycle RED System is N A GREEN powering up ORANGE Please allow up to 30 seconds Flashing BASE UNIT will 1 Unplug the BASE UNIT power supply GREEN flash GREEN Relocate the EXTERNAL ANTENNA to pick up the strongest signal from your wireless carrier in the system the BASE UNIT will not operate optimal system gain Three 3 Move the EXTERNAL ANTENNA as far a
23. way from the S flashes or less INDOOR ANTENNA as possible with at least 15 ft of 5 indicates the vertical separation height difference ZS system will still Gees properly 4 Plug the BASE UNIT power supply back in 5 Wait 30 secs for the BASE UNIT to power cycle on After Initial Power Up Light Mode Status Solution SOLID zBoost is ready N A GREEN Flashing zBoost is in use N A GREEN SOLID EXTERNAL 1 Unplug the BASE UNIT power supply ORANGE ANTENNA and INDOOR 2 Move the EXTERNAL ANTENNA as far away from the ANTENNA INDOOR ANTENNA as possible with at least 15 ft of are too close vertical separation height difference 2 together d P 3 Plug the BASE UNIT power supply back in 2 4 Wait 30 secs for the BASE UNIT to power cycle on SOLID RED Signal from the 1 Unplug the BASE UNIT power supply carrier s cell tower is too 2 Relocate the EXTERNAL ANTENNA to another spot D strong for the E SSC Z BASE UNIT to 3 Ifyou have a directional antenna re aim it to reduce E carrier signal strength 5 operate properly g g 3 4 Plug the BASE UNIT power supply back in 5 Wait 30 secs for the BASE UNIT to power cycle on Flashing Excessive Refer to Solution 2 RED electronic noise zBoost Max ZB545M Manual Technical Specifications Product Specifications for zBoost Max ZB545M PCS band Frequency Uplink 1850 to 1910 MHz Downlink 1930 to 1990 MHz CDMA GSM GPRS EDGE EVDO 1xRTT UMTS HSPA 3G
24. ws not included then snapping the Base Unit back in place keeping the Indoor Antenna vertical The Base Unit uses an omni directional Indoor Antenna that delivers signal in a circular pattern around the antenna The zBoost Max requires at least 15 feet of vertical separation between the Base Unit and the External Antenna Generally increasing this distance up to 40 feet will increase the performance and decreasing the distance will limit the performance Keep the Base Unit off the floor and at least 2 feet away from other cords metal objects or other wireless devices such as wireless routers or wireless access points zBoost performs best when there are no obstructions between the zBoost Base Unit and your mobile device Indoor Antenna zBoost Base Unit Coaxial Cable Power Supply MASTER KITCHEN BEDROOM THIRD Run the Coaxial Cable NOTE Refrain from securing cable or drilling holes until the system has been tested The zBoost Max comes with 2 coax cables 35 ft and 15 ft and a window entry cable If you do not plan to run the cable through a window the window entry cable is not needed To run the coax cable through a window Connect the two provided RG 6 cables 35 feet amp 15 feet using the provided window entry cable Use the attached cables to connect the Base Unit and External Antenna through a window positioning the window entry cable at the window closing zBoost Max ZB545M Manual To run the coax
Download Pdf Manuals
Related Search