B-Tech BT7533
Contents
1. mounting this bracket If you do not understand the instructions provided or are not sure how to install this product please contact a professional for advice and or to install this mount Failure to mount this bracket correctly may lead to serious injury and ordeath Please pay careful attention to where this mount is located Some walls are not suitable for installation If you install this mount on drywall it must be anchored into a wood stud concrete block or brick behind the drywall It is not suitable for securing to steel studs or weak concrete brick Installing on drywall alone will not support the weight of a flat panel screen Ensure sufficient space and safety distance is allowed when installing this product If installing in a public area or over the likely path of pedestrians this product should be mounted as far as possible from the public pedestrians When drilling holes it is particularly important to take care of electrical cables water or gas pipes in the wall It is important that all fixing screws supplied are used If the fixing screws included are not sufficient for the wall you are mounting this product on please consult your local hardware store The screen attached must weigh no more than the recommended weight of 40 Kg 88lbs This mount must be mounted on a wall horizontally to prevent free motion due to the weight of the screen when adjusting the position Ensure that when installing your screen on this mount that th2. use 4 Choose location for flat panel wall mount Depending on the wall e g concrete wall It is necessary to drill suitable dowell wall plug holes beforehand Hold the wall plate part 1 against the wall with the label including directional arrow facing towards you and upwards and mark through the desired position for where to drill the holes Screw locations and quantities are for illustrative purposes only and not all wall fixing screws may have been shown Distribute screws as evenly as possible to spread the load Use the provided washers part 13 with coach screws part 11 The bracket should be mounted to a concrete brick wall or stud wall If you are unsure about mounting this product please consult with a professional installer PLEASE PAY CAREFUL ATTENTION TO WHERE THIS MOUNT IS LOCATED SOME WALLS ARE NOT SUITABLE FOR INSTALLATION IF YOU INSTALL THIS WALL MOUNT ON DRYWALL IT MUST BE ANCHORED INTO A WOOD STUD CONCRETE BLOCK OR BRICK BEHIND THE DRYWALL INSTALLING ON DRYWALL ALONE WILL NOT SUPPORT THE WEIGHT OF A TELEVISION WHEN DRILLING HOLES IT IS PARTICULARLY IMPORTANT TO TAKE CARE OF ELECTRICAL CABLES WATER OR GAS PIPES IN THE WALL IT IS IMPORTANT THAT ALL FIXING SCREWS SUPPLIED ARE USED Attach interface plate to rear of screen Depending on the VESA pattern on rear of LCD screen fasten the VESA plate part 2 to the screen by using M4 M5 or M6 Allen screws part 4 9 are supplied When using the M5 x 25mm
3. Allen screws part 7 or M6 x 25mm Allen screws part 9 on screens with recessed fixings use the provided spacers part 10 IF UNSURE ABOUT THE MOUNTING PATTERN ON REAR OF SCREEN PLEASE CONSULT THE SCREEN S USER MANUAL BN BT7533 LOD SCREEN WALL MOUNT cn ee WITH TILT 4 Hang screen onto wall bracket This procedure may require two people Carefully lower the screen so that the bottom slots in the interface plate part 2 locate over the bottom pins if the wall plate part 1 Ensure both the left and right slots have been located securely before releasing the weight of the screen Once satisfied gently lower the weight of the screen and tilt forwards until the two top pins of the interface plate stop in the two notches on the wall plate The screen is now sitting in a safe position allowing one person to easily adjust and fix the tilt THIS PROCEDURE MAY REQUIRE TWO PEOPLE supporting hole First locate 1 x security Allen screw Part 3 fitted with a washer part 13 in the bottom of the two curved slots where you see a threaded hole Repeat this on the other side Make sure to leave these screws loose enough so that you can still adjust the tilt Next Decide upon the tilt angle you require For 15 degrees tilt Insert the remaining two security Allen screws with washers into the visible threaded hole in the top curved slot repeat on the other side For 7 5 degrees tilt push the screen back in
4. B j BT 7533 LCD SCREEN WALL MOUNT WITH TILT SETTER ov DESIGN PARTS LIST ee ee ae 1 waua Ct 2 INTERFACEPLATE 1 3 M x 12mm SECURITY ALLENSCREW 4 4 M xtOmmALLENSCREW 6_ 5 M xtSmmALLENSCREW 6 MSxt6mmALLENSCREW 8 MBx t6mmALLENSCREW 9 Mex25mmALLENSCREW 10 265mmgidmmx9S5mmSPACER 11 MBx50mmCOACHSCREW 12 owaPue e 13 08 3mm O19mmT1 6mmWASHER 10 14 25mmALLENKEY 1 15 ammALLENKEY 16 maene 17 SmmSECURITYALLENKEY 1 BT7533 is compatible with B Tech Accessory collars Non Vesa adaptor kit also available from B Tech Please visit website for more details www btechavmounts com 4 BETTER DESIGN BA LCD SCREEN MESS v OR1BX 1007 Registered Design No 4003130 WALL MOUNT WITH TILT RECOMMENDED FOR SCREEN SIZES UP TO 42 e 15 Tilt down e Designed for LCD screens with a weight up to 40Kg 88Ibs e VESA mounting patterns 200mm x 200mm 200mm x 100mm 100mm x 100mm amp 75mm x 75mm ASSEMBLY AND INSTALLATION GUIDE THIS PACK CONTAINS 1 WALL MOUNT amp 1 MOUNTING HARDWARE KIT 10mm 3 8 Drill bit required Important Safety Instructions Do not install this product until the instructions and warnings have been read and understood thoroughly Please keep these instructions for future reference Due to the weight of LCD Screens and their fragile nature B Tech recommends that a professional installer is used when
5. e correct viewing distance and angles are observed as well as avoiding any direct or refiected glare including glare from electric lighting etc If there is any doubt consult the instruction manual of your screen Proper attention should be paid when laying the connecting cables so that they do not cause a hazard It is recommended that periodic inspections are made of the mount to ensure that there is no change to the fixings or mount When cleaning the mount use dry cloth only B Tech International Limited its distributors and dealers are not liable or responsible for damage or injury caused by improper installation improper use or failure to observe these safety instructions In such cases any guarantee will expire A CAUTION This wall mount is intended for use only with the maximum weights indicated Use with heavier than the maximum weights indicated may result in instability causing possible injury For more information on B Tech Audio Video Mounts please visit www btechavmounts com B Tech International Limited OCOPYRIGHT 2007 B Tech Audio Video Mounts Long March Daventry Sparks NV 89431 USA Northants NN11 4NR U K Tel 1 800 975 5812 Fax 1 800 592 2876 info b tech int com info btechavmounts com Made in China BN BT7533 LOD SCREEN WALL MOUNT i 20 WITH TILT 1 Before Installation Loosen the security Allen screws part 3 and washers part 13 Separate the wall plate part 1 and interface plate part 2 for later
6. to the vertical position and be sure to hold it there Insert the remaining two security Allen screws with washers into the middle of the three threaded holes in the top curved slot repeat on the other side Release the screen weight For vertical position As above but insert the screws with washers into the holes nearest the wall Release the screen weight Once all 4 x screws are in position tighten them all fully using the Allen key provided Part 17
Download Pdf Manuals
Related Search