ACTi E92 surveillance camera
Contents
1. Hardware Manual 4 Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a C class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to the equipment that are not expressly approved by the responsible party for compliance could void the user s authority to operate the equipment European Community Compliance Statement C 4 This product has been tested and found to comply with the limits for Class B Informatio2. Indoor Mini Dome amp Indoor Mini Fisheye Dome Hardware Manual D91 D92 E91 E92 E93 E94 E95 E96 E97 E98 Ver 2014 06 27 pd ACTI gt Connecting Vision 4 wei Hardware Manual Table of Contents B ACTi _ Connecting Vision Precautions 4 Safety Instructions mm 6 Introduction 7 List Of OS ann kana sawak ana seca na nk wa kaa Na na ara pi aarian 7 Package ContentS nanne nennnenanennnnennanennanennnrenn 8 Physical Description zanden nenten nende nentekenendec in dendecnmdend 9 Installation Procedures 11 Installing the Camera on a Surface annnannnnenanenenennn 12 Installing the Camera on a Gang BOX nan nnnnnnnnenenn 15 Siep E Install he GENT BOX avn 16 Step 2 Install the Gang Box Converter asana eaaa aaa eaaa eee 17 Step 3 Connect the Cable nanne enne nean eaaa aane eee 18 Step 4 Install the Camera naar vener venen venen venen vennen 18 Step 5 Connect to Network aaneen nennen nennen 19 Step 6 Access the Camera Live VIEW ana eneen 19 Step 7 Adjust the Viewing Angle and FOCUS en 19 Step 8 Close the Dome Cover annae nennen eenen nennen 19 Basie GonnecHoNS sasana aa NA a aa a GA aa NAN AN aaa aa Na aaa aa a aa anaa 20 Other Adjustments and Accessories 21 How to Adjust the Viewing Angle and FOCUS annae 21 How to Rotate the Viewing Orientation E96 E98 23 How to Replace the Dome Cover nnnnanenenareenanrennane ennen 24 How
3. button of the IP Utility you will be able to see the list of cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time 32 Hardware Manual Pa ACT Connecting Vision Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment it is possible to use the Web browser of the PC to access the camera You can use any of the browsers to access the camera however the full functionality is provided only for Microsoft Internet Explorer The browser functionality comparison a ANENG ive video wrea nesae ve No Video overlay based configuration Motion Detection regions Privacy Mask regions All the other configurations When using non Internet Explorer browsers free third party software plug ins must be installed to the PC first to be able to get the live video feed from the camera Required Plug In QuickTime http www apple com quicktime download Other non Internet Explorer Basic VLC Media Player http www videolan org browsers Disclaimer Notice The camera manufacturer does not guarantee the
4. safely unmount the card see the camera Firmware Manual for details Once unmounted from the firmware push the card to eject it from the slot 1 Hardware Manual pd ACT 1 _ Connecting Vision Installation Procedures Before mounting the camera remove the dome cover by loosening the three 3 screws NOTE Some models have styrofoam inside the dome cover which is used to protect the lens during shipping Remember to remove the styrofoam before mounting the camera There are two ways to mount the camera e Surface mount Use this method to mount the camera directly on the ceiling See Installing the Camera on a Surface on page 12 e Gang Box Mount If the camera will be mounted on a gang box applicable in some areas in the US a gang box converter not included in the camera package is needed See Installing the Camera on a Gang Box on page 15 1 WA lt gt Hardware Manual ACTI Connecting Vision Installing the Camera on a Surface 1 Mark the location of the screw holes base on the drill template included in the package Conduit Hole NOTE Depending on the surface where you will install the camera it may be necessary to drill three 3 holes with 3 5 on the ceiling and use the supplied screw tox 2 Route the cables through the ceiling taking the Conduit Hole on the drilling template as a reference Or slide off the cable exit tab on the dome cover to route the cable
5. 0 z Basic Search Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Account Password 123456 IP Address MAC Address FW Version Model Serial No Multicast IP Status 172 16 26 183 00 0F 7C 0A 3F 26 A1D 500 V6 04 05 AC Megapixel IP Dome D91 A XX 13E 00048 5 6 a 172 16 26 197 00 0F 7C 0A A1 25 A1D 500 V6 04 05 AC Megapixel IP Dome D92 A XX 13E 00047 172 16 26 15 00 0F 7C 09 7A 6B A1D 500 V6 03 17 AC Megapixel IP Cube Camer E13 A XX 12K 00041 228 5 6 1 192 168 0 208 00 0F 7C 09 7A 70 A1D 500 V6 04 03 AC Megapixel IP Cube Camer E13 A XX 12K 00046 228 5 6 1 172 16 26 9 00 0F 7C 0A 1E 06 A1D 500 V6 03 17 AC Megapixel IP Camera E22 A0XX 13B 00009 228 5 6 1 OILLL 172 16 26 11 00 0F 7C 0A 2B 76 A1D 500 V6 03 17 AC Megapixel IP Camera E24 A XX 13B 00006 228 5 6 1 172 16 26 4 00 0F 7C 09 BB 20 A1D 500 V6 03 17 AC Megapixel IP Camera E41 A XX 12L 00112 228 5 6 1 172 16 26 243 00 0F 7C 09 B9 76 A1D 500 V6 03 17 AC Megapixel IP Camera E42 A XX 12L 00236 228 5 6 1 172 16 26 137 00 0F 7C 09 52 0E A1D 500 V6 02 03 AC Megapixel IP Dome ES1 A XX 12J 00073 228 5 6 1 192 168 0 156 00 0F 7C 09 95 6C A1D 500 V6 02 03 AC Megapixel IP Dome E53 A XX 12K 00147 228 5 6 1 172 16 26 180 00 0F 7C 09 D5 BD A1D 500 V6 03 17 AC Megapixel IP Dome ES3 A XX 13A 00089 228 5 6 1 192 168 0 173 00 0F 7C 09 F8 F3 A1D 500 V6 03 10 AC Megapixe
6. Hardware Manual Da ACTi _ Connecting Vision Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only the last number of the IP address is different from each other There are 2 different approaches to IP Address management in Local Area Networks by DHCP Server or Manually Using DHCP Server to Assign IP Addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from DHCP server automatically In such case the camera will immediately be ready for the access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in other to be able to access it by using a Web browser The quickest way to discover the cameras in the network is to use the simplest network search built in the Windows system just by pressing the Network icon all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our cameras In the example below we successfully found the camera that we had just connected to the network
7. to Replace the Lens D91 D92 only annen 26 Accessing the Camera 29 Configure the IP Addresses nnnsnnnnnneneeeeneneneneeeennnneenn 29 wuww acti Com ACTI Connecting Vision Hardware Manual DP Using DHCP Server to Assign IP Addresses nun nnen 29 Using the Default Camera IP Address nnen eneen 31 Access Ine Gamera imaan testen 33 3 www acti com ACTI Connecting Vision Hardware Manual Pp Precautions Read these instructions You should read all the safety and operating instructions before using this product Heed all warnings You must adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instruction given may directly endanger people cause damage to the system or to other equipment Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Trademarks All names used in this manual are probably registered trademarks of respective companies Liability Every reasonable care has been taken during the writing of this manual Please inform your local office if you find any inaccuracies or omissions We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice 4 www acti com ACTI Connecting Vision
8. 20 for more information Step 6 Access the Camera Live View See Accessing the Camera on page 29 for more information on how to access the Live View of the camera Step 7 Adjust the Viewing Angle and Focus Based on the Live View adjust the viewing angle focus and orientation of the camera Adjustments vary depending on model see How to Adjust the Viewing Angle and Focus on page 21 or How to Rotate the Viewing Orientation E96 E98 on page 23 for more information Step 8 Close the Dome Cover 1 Align cable tab side of the dome cover to the direction of the network cable 2 Tighten the three 3 screws using the supplied hex screwdriver to attach the dome cover Final installation should look similar to the illustration below e Hardware Manual B ACTi _ Connecting Vision Basic Connections Follow the procedures below to connect the camera to the network Please use a PoE Power over Ethernet supported switch or injector 1 Connect your IP Camera to the PoE Switch Injector using an Ethernet cable 2 Connect your PoE Switch Injector to a PC network using another Ethernet cable 20 ACTI Connecting Vision Hardware Manual gt Other Adjustments and Accessories How to Adjust the Viewing Angle and Focus NOTE The following procedures are not applicable to E96 Mini Fisheye Dome cameras 1 Loosen the three 3 screws to remove the dome cover 2 Based on t
9. IC gt Network gt Organize v Search Active Directory Network and Sharing Center DUL A AAW LS C UUUUU D72 A XX 13A 00162 n D91 A XX 13E 00048 4 Libraries k D92 A XX 13E 00047 el Documents E13 A XX 12K 00041 a Music Pictures Videos Recent Places 1 E22 A0XX 13B 00009 1 E24 A XX 13B 00006 1 E41 A XX 13A 01224 1 E42 A XX 12L 00286 1 E51 A XX 12J 00073 1 E53 A XX 13A 00089 1 ENR1200 ENR 1 ENR2000 ENR 4 Ga Network EB ADRIAN GARCIA EE Computer sE ARTIIR_DAK 77 items 29 ACTI Connecting Vision Hardware Manual gt By double clicking with the left mouse on the camera model it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already If you work with our cameras regularly then there is even a better way to discover the cameras in the network by using IP Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time The IP Utility can be downloaded for free from http www acti com IP_ Utility With just one click you can launch the IP Utility and there will be an instant report as follows IP Address NetMask 172 16 26 189 255 255 255
10. Serial No Multicast IP Status KA RA 172 16 26 2 00 0F 7C 07 DE 65 A1D 311 V5 07 05 AC Hemispheric Camera KCM3911 228 5 6 1 A ZF 172 16 26 4 00 0F 7C 08 17 C2 A1D 310 V4 12 02 AC Mega IP Camera TCM1111 228 5 6 1 172 16 26 6 KCM7311 228 5 6 1 4 Change Network Address ss 172 16 26 7 i TCM6630 228 5 6 1 WF 172 16 26 10 Dynamic IP Address TCM4201 228 5 6 1 RA 172 16 26 11 00 4 KCM3911 228 5 6 1 A 172 16 26 13 od Static IP Address KCM5111 228 5 6 1 F WF 172 16 26 40 00 KCM5211 228 5 6 1 Starting IP Address 192 168 0 101 BE 172 16 26 41 00 0 s KCM5311 228 5 6 1 RA 172 16 26 50 00 0 Netmask 255 255 255 0 KCMS111 228 5 6 1 Fh 172 16 26 52 00 0 KCM5311 228 5 6 1 Gateway 192 168 0 254 S A 172 16 26 53 00 0 TCM5311 228 5 6 1 i 172 16 26 54 00 0 TCM5611 228 5 6 1 A RA 172 16 26 55 00 0 pply TCMS111 228 5 6 1 WA 172 16 26 57 00 0F 7T 04 87 K1D 310 V4 12 09 2 Video Server TCD2100 228 5 6 1 16 25 Ur UI 31U TZ wegapKe amera Y gt 0 RA 172 16 26 61 00 0F 7C 04 32 E3 A1D 310 V4 12 09 AC Megapixel IP C TCM1231 228 5 6 1 With the procedure shown above all the cameras will have unique IP addresses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 168 0 120 Later by pressing the Refresh
11. cheduler Subnet mask 255 255 255 0 M File and Printer Sharing for Microsoft Networks Default gateway Obtain DNS server address automatically K KKK sika Link Layer Topology Discovery Responder Use the following DNS server addresses Install Uninstall Properties Preferred DNS server Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Alternate DNS server Validate settings upon exit OK 3 Cancel amu sa Cancel 3 ACTI Connecting Vision Hardware Manual gt Manually adjust the IP addresses of multiple cameras If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them all of the cameras would then have the initial IP address of 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each other The easiest way to assign cameras the IP addresses is by using IP Utility IP_Utility IP Address NetMask 172 16 26 192 255 255 255 0 z Basic Search z Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Total 56 Account Password 123456 Http Port IP Address MAC Address FW Version Model
12. compatibility of its cameras with VLC player or QuickTime since these are third party softwares The third party has the right to modity their utility any time which might affect the compatibility In such cases please use Internet Explorer browser instead When using Internet Explorer browser the ActiveX control for video stream management will be downloaded from the camera directly the user just has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case 33 Hardware Manual B ACTi _ Connecting Vision The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera Assuming that the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into Web browser s address bar http 192 168 0 100 Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80 which can be omitted from the address for convenience fey Web Configurator Web Configurator Account Password Language English x Login Reset Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456 For f
13. erating Instructions in this manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine if the video product is in proper operating condition 6 www acti com ACTI Connecting Vision Hardware Manual DP Introduction List of Models This hardware manual contains the following models 1MP Indoor Mini Dome with Fixed lens 3MP Indoor Mini Dome with Fixed lens 1MP Indoor Mini Dome with Basic WDR Fixed lens 3MP Indoor Mini Dome with Basic WDR Fixed lens 5MP Indoor Mini Dome with Basic WDR Fixed lens 1 3MP Indoor Mini Dome with Basic WDR SLLS Fixed lens 2MP Indoor Mini Dome with Basic WDR SLLS Fixed lens SMP Indoor Mini Fisheye Dome with Basic WDR Fixed lens 10MP Indoor Mini Dome with Basic WDR Fixed lens 1OMP Indoor Mini Fisheye Dome with Basic WDR Fixed lens www acti com ACTI Connecting Vision Hardware Manual gt Package Contents Camera Camera Mini Dome Mini Fisheye Dome Drill Template Lens Focus Tuner Hexagon Screwdriver Not available in E93 E96 and E97 models Quick Installation Guide Warranty Card Hardware Warranty P
14. he live view from the camera adjust the viewing angle with pan and tilt direction for Mini Dome models only 2 ACTI Connecting Vision Hardware Manual gt 3 Adjust the focus NOTE Not applicable for E93 E97 model because the camera is already pre focused a Attach the focus tuner included in the camera package on the lens and adjust the focus of the lens b Remove the lens focus tuner 4 Attach the dome cover to the camera and tighten the three 3 screws 2 ACTI Connecting Vision Hardware Manual gt How to Rotate the Viewing Orientation E96 E98 This section describes the procedures in rotating the viewing orientation of Mini Fisheye Dome Cameras 1 Open the dome cover 2 Loosen the screw as marked below 3 Turn the lens holder to rotate the viewing orientation Note that the arrow indicates the viewing direction 5 Close the dome cover 23 WA lt gt ACTI Connecting Vision Hardware Manual How to Replace the Dome Cover For more discrete surveillance needs the pre installed dome cover can be replaced with a smoked non vandal proof dome cover The smoked dome cover is an optional accessory contact your sales agent to purchase Optional Accessories PDCX 1106 To replace the dome cover follow the procedures below 1 Loosen the three 3 screws to remove the dome cover 2 Push the clips out
15. l Home Ch dapter setti r See full map fera ang a A Jo bed Ax Local Area Connection Ch d d shari 4 a SISO_NP_PC1 Network Internet MAN rar This computer ae Intel R 8 aj Disable View your active networks Connect or disconnect Status Diagnose Jo Network Access type Internet Work network Connections Local Area Connection la Bridge Connections Create Shortcut Delete Change your networking settings de Set up a new connection or network lt S 7 Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or A Rename access point Wa Properties Connect to a network je Connect or reconnect to a wireless wired dial up or VPN network connection See also HomeGroup Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing settings Windows Firewall cms Connect using You can get IP settings assigned automatically if your network supports E A 7 this capability Otherwise you need to ask your network administrator LA Intel R 82567LM 3 Gigabit Network Connection for the appropriate IP settings Obtain an IP address automatically This connection uses the following items z a Use the following IP address wl 0 Client for Microsoft Networks wl Sl VirtualBox Bridged Networking Driver IP address 192 168 0 99 M dE QoS Packet S
16. l IP Dome E73 A XX 13A4 00028 228 5 6 1 192 168 0 183 00 0F 7C 09 F9 57 A1D 500 V6 03 15 AC Megapixel IP Dome ES83 A XX 13A 00018 228 5 6 1 cei e AAN panas OL LI EN 4 You can quickly see the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already 30 ACTI Connecting Vision Hardware Manual gt Using the Default Camera IP Address lf there is no DHCP server in the given network the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment When the camera is plugged into network and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera Manually adjust the IP address of the PC In the following example based on Windows 7 we will configure the IP address to 192 168 0 99 and set Subnet Mask to 255 255 255 0 by using the steps below BE All Control Panel Items Network and Sharing Center View your basic network information and set up connections Organize wv Disable this network device Diagnos Control Pane
17. n Technology Equipment according to European Standard EN 55022 and EN 55024 In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures 5 www acti com ACTI Connecting Vision Hardware Manual Pp Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Water and Moisture Do not use this video product near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Don t use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord or plug is damaged 2 If liquid has been spilled or objects have fallen into the video product 3 If the video product has been directly exposed to rain or water 4 If the video product does not operate normally by following the op
18. ng orientation Screw Holes from Left to Right Screw Holes from Right to Left 1 Remove a knockout on the gang box to route the network cable 2 Route the network cable along the surface or inside the surface and into the gang box 3 Attach the gang box on the surface or inside the surface according to the recommended orientation above 6 ACTI Connecting Vision Hardware Manual gt Step 2 Install the Gang Box Converter 1 Route the network cable to pass through the hole of the gang box converter 2 Install the gang box converter onto the gang box using the screws included in the gang box package Note which screw holes to attach to secure the converter to the gang box Screw Holes from Left to Right Screw Holes from Right to Left NOTE Same screw holes apply when using the 4 octagon gang boxes 17 ACTI Connecting Vision Hardware Manual gt Step 3 Connect the Cable Connect the network cable to the Ethernet port of the camera Step 4 Install the Camera 1 Align the camera screw holes to the screw holes of the gang box converter 2 Attach the three 3 screws included in the gang box converter package to secure the camera to the converter is ACTI Connecting Vision Hardware Manual gt Step 5 Connect to Network On the network side connect the other end of the network cable to a network switch See Basic Connections on page
19. olicy wg acri Tres guide comtare me basic forranon you meed to WAY sep Camera For Otak wlormaken on NA so anons pioase refer to Da Hardware Martial and F rrara Marisa on af t J 8 www acti com ACTI Connecting Vision Hardware Manual gt Physical Description Mini Dome 3 Mini Fisheye Dome 9 www acti com ACTI Connecting Vision Hardware Manual 4 1 Ethernet Port The Ethernet port connects to a network using an Ethernet cable 2 Reset Button The Reset Button is used to restore the factory default settings of the camera including the administrator s password How to reset the camera While the power is on press and hold the Reset Button for 5 seconds or until the Blue LED lights up 3 LED Indicators e Blue LED The Power LED lights blue when the camera is powered on the light goes off once the initial boot up process is complete e Amber LED The Ethernet Activity LED blinks amber when network activity is in progress e Green LED The Ethernet Link LED lights green when a network connection is established 4 Memory Card Slot Insert a memory card not included into this slot for local recording NOTE Supports microSDHC and microSDXC cards How to install the memory card Insert the memory card into the slot with the metal contacts facing down and then push the card until it clicks into place How to remove the memory card Access the Web Configurator to
20. through that hole later 12 ACTI Connecting Vision Hardware Manual gt 3 Use the camera body and locate the three 3 screw holes 4 Install the camera body to the ceiling using the three 3 screws included in the camera package NOTE Please make sure the screw is flat on the plate 13 WA lt gt ACTI Connecting Vision Hardware Manual 5 Connect the Ethernet cable to the Ethernet port of the camera 6 Adjust the camera viewing angle and focus See How to Adjust the Viewing Angle and Focus on page 21 NOTE Not applicable to E96 model 7 Attach the cover to the camera body and tighten the three 3 screws to secure it 14 ACTI Connecting Vision Hardware Manual gt Installing the Camera on a Gang Box In case the camera has to be installed on a gang box use the gang box converter below to install your camera Rig Supported Gang Box Converter Description Gang Box PMAX 0805 The gang box converter is installed onto the gang 4 Round box which can either be on a surface or inside the 4 Octagon surface The camera can then be installed onto the gang box converter NOTE The gang box and the gang box converter are not included in the camera package is ACTI Connecting Vision Hardware Manual gt Step 1 Install the Gang Box Before installation note that the gang box must be installed with either of the followi
21. urther operations please refer to the Firmware User Manual 34 ACTI Connecting Vision Copyright 2014 ACTi Corporation All Rights Reserved 7F No 1 Alley 20 Lane 407 Sec 2 Ti Ding Blvd Neihu District Taipei Taiwan 114 R O C TEL 886 2 2656 2588 FAX 886 2 2656 2599 Email sales acti com
22. wards to release the dome cover latches 24 ACTI Connecting Vision Hardware Manual gt 3 Remove the ring from the cover A 4 Insert ring to the new dome cover and latch it to the cover body 25 ACTI Connecting Vision Hardware Manual gt How to Replace the Lens D91 D92 only For wider viewing angle the bundled lens can be replaced with the optional IR compatible lens Contact your sales agent to purchase To replace the lens follow the procedures below 1 Using the bundled hex screwdriver loosen the three 3 screws to open the dome cover 2 Attach the lens focus tuner to the lens and continuously rotate until the lens comes off 3 When the lens comes off remove the spring and remove the bundled lens from the lens focus tuner 6 ACTI Connecting Vision Hardware Manual gt 4 Remove the transparent plastic from the replacement lens 5 Attach the spring to the replacement lens ayni 6 Continuously rotate the replacement lens to attach it to the camera a ACTI Connecting Vision Hardware Manual gt 7 Attach the lens focus tuner when the tip of the lens is difficult to hold then turn it clockwise or counter clockwise to adjust the camera focus See How to Adjust the Viewing Angle and Focus on page 21 for more information 8 Close the dome cover 28
Download Pdf Manuals
Related Search