Planar Systems PT1745R
Contents
1. Choose the adjustment items by pressing the Enter button Adjust the value of the adjustment items by pressing the Up or Down button With the OSD menu on screen press Menu button to return main menu or exit OSD The OSD menu will automatically close if you have left it idle for a pre set time To Lock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press Menu key the OSD menu will pops upon display b Press and hold the Menu key again with the OSD menu on the screen the OSD menu will disappear Then press the Power key 1 time while the menu key is still being pressed The Lock Unlock menu will appear for 3 seconds c Use the Enter key to select OSD or Power setting then set at Lock by pushing the UP or Down button d When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically 7 To Unlock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press and hold the Menu key then press the Power key simultaneously the Lock Unlock menu will appear for 3 seconds b Use the Enter key to select OSD or Power setting then set at Unlock by pushing the UP2. or Down button c When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically Please note a When the OSD Lock function is selected this indicates that all the buttons except power button are now disabled b When the Power Lock function is selected this indicates that the power key is disabled user can not to turn off the monitor by Power key O R V N On Screen Display Menus Main OSD Menu ITEM CONTENT Contrast The monitor luminance level control Brightness The monitor backlight level control Auto Adjust Fine tune the image to full screen automatically Left Right Moving screen image horizontal position to left or right Up Down Moving screen image vertical position to up or down Horizontal size The screen image horizontal dot clock adjustment Fine The screen image pixel phase adjustment OSD Left Right Moving OSD menu horizontal position to left or right OSD Up Down Moving OSD menu vertical position to up or down OSD Time out OSD auto disappear time selection OSD menu language selection English French Japanese Deutsch OSD Language y Ka VERO Spanish Italian Traditional Chinese and Simplified Chinese Factory Reset Factory default value restored RGB Color temperature selection 9300K 6500K 5500K 7500K User Volume Audio volume adjustment Mute Audio On Off control Appendix Troubleshoo
3. 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1280 x 1024 1280 x 1024 1280 x 960 1152 x 864 640 x 480 832 x 624 H Frequency KHz 31 47 31 47 37 86 37 50 35 16 37 88 48 08 46 88 48 36 56 48 60 02 64 00 80 00 60 00 67 50 35 00 49 72 V Frequency Hz 70 60 72 75 56 60 72 75 60 70 75 60 75 60 75 66 75 Touch Screen Driver Installation The PT1745R PT1745S is available with both RS232 and USB connections The touch driver is located on the enclosed CD ROM for these operating systems Windows 7 VISTA XP 2000 ME 98 NT 4 0 CE XP Embedded Linux Apple Mac OS Please Note The PT1745R PT1745S is Microsoft Windows HID Human Interface Device compatible if you use the USB touch screen interface No additional software driver is required for general operation of the touch screen A calibration tool can be installed for improved touch position accuracy See Optional Calibration Tool Install section for more information PT1745R PT1745S Optional Calibration Tool Install If you would like to use the Optional Calibration Tool follow the instructions below Please note the calibration tool supports Windows 7 VISTA XP XP Embedded 2000 98 and ME operating systems via USB only Open the CD ROM Select the monitor size and then model name Click on the Load Utility button that appea
4. PLANAR PT1745R PT1745S Touch Screen Monitor USER S GUIDE www planar com The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another language or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders The test results show that this device meets the FCC rules Those limits are set to protect residential areas from the devices with harmful emission This device will produce use and radiate radio frequency energy In addition failure to follow the user s manual to install or use this device might produce harmful interference with radio communication Not withstanding the foregoing it does not guarantee that this type of harmful interference does not occur in some special installations The interference caused by this device to the reception of radio or television signals may be verified by turning it on and off Any changes or modifications to this TFT LCD would void the user s authority to operate this device Important Recycle Instructions Lamp s inside this product contains mercury This product may contain other electro
5. com support for operations manuals touch screen drivers warranty information and access to Planar s Technical Library for online troubleshooting To speak with Planar Customer Support please have you model and serial number available and dial Planar Support Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the US Hours 24 hours a day 7 days a week Toll or long distance charges may apply Planar Systems Inc Customer Service 24x7 Online Technical Support http www planar com support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the United States Hours 24 hours a day 7 days a week 2013 Planar Systems Inc 7 13 Planar is a registered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice 020 1021 00E 820470035105
6. e used as commercial and light industrial equipment only Features include Direct Analog signal input Active matrix TFT LCD technology 1280 x 1024 SXGA resolution 17 viewable display area 31 47 80 KHz horizontal scan 56 75 Hz high refresh rate 0 264mm x 0 264mm pixel pitch Auto adjustment function Multilingual OSD user control Kensington security slot 100 mm VESA mount Removable base for flexible mounting solutions PT1745R 5 wire resistive touch screen with dual RS 232 Serial USB controller PT1745S SAW touch screen with dual RS 232 Serial USB controller Build in audio 1W x 2 Touch Screen for PT1745R Analog 5 wire resistive touch screen for finger and stylus input Surface Anti glare treatment Interface Dual RS 232 Serial USB controller e Transmittance 82 5 Driver Windows 7 VISTA XP 2000 ME 98 NT 4 0 CE XP Embedded Linux Apple Mac OS Touch Screen for PT1745S Surface Acoustic Wave SAW touch screen for finger and stylus input Surface Anti glare treatment Interface Dual RS 232 Serial USB controller e Transmittance 921596 Driver Windows 7 VISTA XP 2000 ME 98 NT4 0 CE XP Embedded Linux Apple amp Mac OS Package Overview A N Display Power Cord VGA Signal Cable Ke USB Cable Ato B RS 232 Cable Audio in Cable PLANAR T corne taza USERS GUIDE LL Touch Screen Driver Landing S
7. eeeeeeeeeeeeees 18 PT1745R PT1745S Install Instructions Technical Support Usage Notice VAN Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture A Warning Please do not open or disassemble the product as this may cause electric shock Precautions Follow all warnings precautions and maintenance as recommended in this user s manual to maximize the life of your unit Do Turn off the product before cleaning Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and isopropyl alcohol Use a soft cloth moistened with mild detergent to clean the display housing Use only high quality and safety approved AC DC adapter Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time Don t Do not touch the LCD Display screen surface with sharp or hard objects Do not use abrasive cleaners waxes or solvents for your cleaning Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field In direct sunlight Introduction About PT1745R PT1745S The PT1745R PT1745S is a 17 flat panel screen with an active matrix thin film transistor TFT liquid crystal display LCD This unit is to b
8. gnal from the computer graphics card Below are the three kinds of Warning Signal Please check the cable connections or contact your local dealer or Planar for more information No Signal This message means that the display has been powered on but it cannot receive any signal from the computer graphics card Check all the power switches power cables and VGA signal cable Going to Sleep The display is under the power saving mode In addition the display will enter power saving mode when experiencing a sudden signal disconnecting problem The monitor can be activated by pressing any key on the keyboard triggering the mouse or touching the screen Out of Range This message means that the signal of the computer graphic card is not compatible with the display When the signal is not included in the Video Modes list we have listed in the Appendices of this manual the monitor will display this message Product Dimensions 386 8 mm 319 9 mm o A 341 9 mm Front View Side View 222 5 mm 196 1 mm 202 0 mm Top View Compatibility Modes Mode IBM VGA IBM VGA VESA VGA VESA VGA VESA SVGA VESA SVGA VESA SVGA VESA SVGA VESA XGA VESA XGA VESA XGA VESA SXGA VESA SXGA VESA SXGA VESA SXGA Apple Mac Il Apple Mac Resolution 720 x 400
9. nic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG For more information on how to recycle your product please visit WWW PLANAR COM GREEN Table of Contents Usage Notice A ao O 1 Introduction About PT TT45R PT1Z45S italica lia i Earls 2 Touch Screen Tor PT 1745R IPT 1745S ch Ac ido Lean iaia 2 Package OV6erVIQW sen ie PERITO o io 3 Installation Product Overview Front VieW ccades e a des E vanne dele nica LALA ani Bottom View Start Your Installation ss othe Lei iesu eL langues Mal abled oe reatino 5 Connecting the Display Figure Y Msc ret dre sr merisier 6 Figure Ti lesson a Kensington Security Slot VESA Mount Your Monitor Remove the Deskstand User Controls Side Panel Controls How to Use the OSD Menus On Screen Display Menus Appendix Troubleshooting sd ades o asd Aa dlc LD da 14 Warning Signal NO Signal dul A IR E a love Going to Sleep iussis iion eror enis eese rero demi eau tee eva e tore YER e FEE eene RA Out OR Ranges rere Product Dimensions Compatibility Modes Touch Screen Driver Installation PT1745R PT1745S Optional Calibration Tool Install cece ee eeee
10. port of your display to the audio out port of your computer 7 1 5 Connectthe RS 232 or USB cable from the RS 232 or USB port of your display to the RS 232 port or USB port 7 1 of your computer 6 Configure the touch screen Refer to the Touch Screen Driver Installation section on page 18 7 Once the touch screen is configured the monitor is ready for use A Notice To ensure the display works well with your computer please configure the display mode of your graphics card to make it less than or equal to 1280 x 1024 resolution and make sure the timing of the display mode is compatible with the LCD display We have listed the compatible Video Modes of your display in the appendix on page 17 for your reference Figure 7 1 ie Com ITIP mi Hoh B Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products The Kensington lock is not included K M y Kensington Security Slot VESA Mount Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors and corresponding with the standards of flat panel monitor mounting devices
11. rs to the right of the model name The HID calibration tool will automatically open From here the user can choose to do the following BON gt a 4 Points Calibration b 9 Points Linearization c 25 Points Linearization d Clear e Draw Test f Advanced In the Advanced settings area the user may do the following i Adjust the Double Click Area ii Enable auto right click and adjust the auto right click time iii Choose to be either in the HID Mouse Mode or HID Digitizer Mode Windows Vista only iv Simply click the Apply button once the settings are finalized PT1745R PT1745S Install Instructions If you are using a PC running Windows 7 VISTA XP 2000 ME 98 NT4 0 follow the instructions below 1 2 Power on the PC Be sure the USB or the RS 232 Serial cable is connected from the PC to the LCD display Open the CD ROM Follow the step by step instructions as shown on the pop up windows If you are using a PC running Windows XP Embedded follow the instructions below Express 1 2 3 Power on the computer Make sure that the RS232 or USB cable is connected to the computer Be sure that your EWF is disabled If your EWF is enabled please disable the EWF by using the EWF Manager command Once the EWF is disabled click on the XP driver on the CD ROM and follow the step by step instructions as shown on the pop up windows Custom 1 2 3 Power on the computer Make sure
12. such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on an UL listed certified swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used 100 0 mm Slots x4 E E S VESA 7 2 Mounting 0 el Interface E e e e a 2 B et x1 Ej ay immo Om A Warning Please select the proper screws The distance between the back cover surface and the bottom of the screw hole is 11 mm Please use four M4 screws diameter with proper length to mount your monitor Please note the mounting stand must be able to support at least 11 Ibs 5Kg Remove the Deskstand Remove 4 screws and then remove hinge User Controls Side Panel Controls Menu off status key Name Menu Up Down Enter Power alee Menu on status Menu appear Menu disappear return to main item Brightness Main item select up Adjust up Mute Main item select down Adjust down Enter Select sub item function Power On Off How to Use the OSD Menus E Menu A Up v Down e Enter 0 Power 1 Press the MENU button to pop up the on screen menu and press Up or Down button to select among the six functions in the main menu
13. that the RS232 or USB cable is connected to the computer Follow the step by step instructions found in the zipped file on the CD ROM If you are using a PC running Windows CE follow the instructions below 1 Poweron the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Using Platform Builder build an image file by following the step by step instructions found in the zipped file on the CD ROM If you are using a PC running Linux or Apple Mac OS follow the instructions below 1 Poweron the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Follow the step by step instructions found in the zipped file on the CD ROM When changing the Touch Interface RS 232 or USB please follow instructions below 1 Uninstall the touch driver Re start the computer Remove the original Touch Interface RS 232 or USB Connect the computer to the Touch Interface RS 232 or USB that you would like to use Load the Touch Driver CD then follow the step by step instructions as show on monitor gi de m PLEASE NOTE Don t plug in both the RS 232 and USB cables Doing so may cause a driver conflict making your touch screen inoperable Technical Support Cables and Accessories To find cables and accessories for your Planar monitor touch screen or other Planar products visit our online store at www PlanarOnline com Technical Support Visit Planar at http www planar
14. ting If you are experiencing trouble with the display refer to the following If the problem persists please contact your local dealer or our service center Problem No image appears on screen gt Check that all the I O and power connectors are correctly and well connected described in the Installation section gt Make sure the pins of the connectors are not crooked or broken Problem Partial Image or incorrectly displayed image gt Check to see if the resolution of your computer is higher than that of the display gt Reconfigure the resolution of your computer to make it less than or equal to 1280 x 1024 Problem Image has vertical flickering line bars gt Use Fine to make an adjustment gt Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the display Problem Image is unstable and flickering gt Use Horizontal size to make an adjustment Problem Image is scrolling Check and make sure the VGA signal cable or adapter is securely connected Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the display Problem Vague image characters and graphics gt Use Fine to make an adjustment If this problem still exists use Horizontal size to make an adjustment Warning Signal If you see warning messages on your screen this means that the display cannot receive a clean si
15. trip User s Guide Installation CD ROM Installation Product Overview Front View S 7 Bottom View POWER SWITCH Start Your Installation Please follow these instructions so that you can hookup the cables to associated connector 1 al Lay the display flat on an even surface 2 Move the stand into position as seen in the step 2 diagram 3 4 Connect the cables to the appropriate connectors as seen in the step 4 diagram Use Remove the cable cover as seen in the step 3 diagram step 4 1 diagram if using the RS 232 serial connector Use the step 4 2 diagram if using the USB connector Position all cables under the cover lip as seen in the step 5 diagram Re attach the cable cover Remove the screw CBM M3x6 from the accessory box and insert the screw into the cable cover and monitor as seen in the step 5 diagram Step 4 1 Step 4 2 Connecting the Display Figure 7 1 To setup this display please refer to the following figure and procedures 1 Be sure all equipment is turned off 2 Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet 7 1 3 Connectthe D SUB cable from the display s VGA input connector to the D SUB connector of your host computer and tighten the screws 7 1 4 Connector the audio in cable from the audio input
Download Pdf Manuals
Related Search