Chief PDR2243B flat panel wall mount
Contents
1. 689 27 12 PDR FULL LEFT PDR Series Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster C d E Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche XA 9 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de2. Bp NN Adjustment nut Figure 3 Installing Covers and End Caps NOTE The covers and end caps have pressure fitting ends that lock into place with each other 1 Install cover B over the top bracket See Figure 4 2 Install end caps C and D into the cover and top bracket See Figure 4 3 Repeat Steps 1 and 2 for the lower mounting bracket See Figure 4 Figure 4 Mounting the Display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 1 5 18 1kg ALWAYS use two people and proper lifting techniques when installing display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons on display are properly seated in mounting holes in faceplate 1 Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall 2 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figure 5 3 Lower display into place listening for audible click to ensure recessed area of mo nting buttons are properly seated in lower area of mounting holes and ClickConnect mechanism has engaged See Figure 5 and See Figure 6 NOTE Holes are provided in the faceplate for use with a pad
3. 1 00 1 00 2 25 i d J 74 1 e PRODUCT FEATURES WEIGHT CAPACITY 200 LBS HEIGHT ADJUSTMENT T TILT ROLL YAW 5 17 2 0 86 m 3 40 DEPTH 500 5 19 69 p ur oa 9 l N 560 22 04 ar ad 3 q 4 600 23 62 END CAP TO END CAP PDR Series Installation Instructions DIMENSIONS cont d Unit Depth T Tit Adjustment Tilted Up Extended Retracted A SC ee SE e BEE H 3 40 SE 1003 D Tilted Down d 39 50 uU The range of adjustment will vary with different weight and depth screens N Highest Height Setting e d 64 x 2 5 2 H Roll Adjustment
4. cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Installation Instructions PDR Series TOOLS REQUIRED FOR INSTALLATION dm T Hl lt 0 Ze 222 7 32 5 5mm 9 16 Di PARTS NOTE Listed PSBU interface bracket provided with Listed Model PDRUS B but not shown B 2 Cover PDR assembly C 2 End cap D 2 End cap E 1 J 12 Adjustment wrench 5 1 2 G 4 Installation washer di il 1 5 16 x 3 1 2 Adjustment insert PDR Series Installation Instructions MOUNT INSTALLATION 9 Place two installation washers G over two lag bolts H See Figure 2 Installing Mount to Wall 10 Install two 5 16 x 3 1 2 lag bolts H through mounting holes in lower wall channel and into pilot holes See Figure 2 WARNING IMPROPER INSTALLATION CAN LEAD TO 11 Place two installation washers G over two lag bolts H MOUNT FALLING CAUSING SERIOUS PERSONAL See Figure 2 INJURY OR DAMAGE TO EQUIPMENT It is the installer s 12 Tighten all hardware DO NOT over tighten responsibility to make sure the structure to which the mount is being installed is capable of supporting five times the combined weight of the mount and all attachments 1 Determine mounting location taking into consideration display size and PDR s range of movement 2 Using a stud sensor locate two wood studs 16 a
5. installing or positioning display on mount 3 Carefully lift display from mount 4 Liftupon pin and place flag back against faceplate to return it to Closed position Remove bolt or padlock if used Pin in Closed position move to Open position to remove display Pin in Open position move to Closed position after display is removed A Figure 16 11 PDR Series Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002473 Rev00 2013 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 10 13 USA International Europe Asia Pacific gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 5 n
6. INSTALLATION INSTRUCTIONS Large Flat Panel Dual Arm Wall Mount CHIEF PDR Series Our Mounts Your Vision PDR Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipmen
7. bly to desired location 4 Tighten the bolts 5 Install the display on the mount Top Bolts Figure 11 Reconfiguring the Swing Arms to the Left or Right of Center 1 Remove the display from the mount 2 Remove four bolts two on the top and two on the bottom securing the swing arm assembly to the top and bottom mounting brackets See figure 14 PDR Series Installation Instructions WARNING The next step will release the arm assembly from the mount The arms and plate may fall if you are not careful 3 Move the swing arm assembly to desired location e Left of Center See Figure 12 Right of Center See Figure 13 4 Install retaining pin assemblies one top and one bottom and secure using two bolts one top and one bottom 5 Install four bolts two on the top and two on the bottom to secure the swing arm assembly to the top and bottom mounting brackets 6 Tighten the bolts 7 Install the display on the mount Top Bolts Figure 12 Top Bolts Figure 13 Swing Arm Tension Adjustment Swing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity If smaller displays are used it may be difficult to reposition the display after mounting Swing arm tension can be adjusted to compensate for smaller display by NOTE The display must be mounted prior to adjusting swing arm tensi
8. ed in the center of the top and bottom mounting brackets which is the standard mounting configuration The top and bottom mounting brackets have slotted holes allowing for lateral adjustment of the dual swing arms After the top and bottom mounting brackets have been installed between two wood studs 16 on center the swing arms can be adjusted or moved off center depending on the location of the mount the size of the display and the lateral movement needed to rotate the display The swing arms can be adjusted as follows e Adjusting the Swing Arms Off Center With no disassembly required you can adjust the swing arms up to 1 inch to the left of center or up to 1 inch to the right of center e Reconfiguring the Swing Arms Left of Center With some disassembly and reassembly required you can move the swing arms to the left of center by reconfiguring the mount Use the first and third slotted holes in the top and bottom mounting brackets e Reconfiguring the Swing Arms Right of Center With some disassembly and reassembly you can move the swing arms to the right of center by reconfiguring the mount Use the third and fifth slotted holes in the top and bottom mounting brackets Adjusting the Swing Arms Off Center 1 Remove the display from the mount 2 Loosen four bolts two on the top and two on the bottom securing the swing arm assembly to the top and bottom mounting brackets See Figure 11 3 Move the swing arm assem
9. lock or similar locking device if desired In addition he pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 6 Figure 5 Touseasa more permanent lock remove pin and nuts and move to lower holes A padlock or bolt may be placed through latch holes Figure 6 PDR Series Installation Instructions 5 cable clamps Figure 7 Cable Management Centris Select Adjustment Knob WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure cables do not run through pinch points 1 Loosen front and rear cable clamps on top arm See Figure 7 2 Thread cable ties J under cable clamps and secure clamps to top arm See Figure 7 3 Route power audio video cables through the cable channel in top arm See Figure 7 allowing sufficient slack in cables for left Right movement of display and swing arm and also swing arm extension and retraction 4 Secure cables to top arm using two cable ties J 5 Repeat Steps 1 through 4 as necessary for remaining top Figure 8 arm and lower arms WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route cables through holes in faceplate Tension Adjustmen
10. on 10 1 Locate the adjustment insert E and wrench E provided with the mount 2 Place adjustment insert into socket head cap screw located at swing arm pivot point See Figure 14 NOTE The display may need to be repositioned in order to gain access to the tension adjustment screw s 3 Using the wrench provided with the mount turn adjustment insert clockwise to increase swing arm tension or counterclockwise to reduce swing arm tension See Figure 15 NOTE Small adjustments of 1 8 turn or less are typically all that is required to achieve desired tension 4 Check swing arm tension If desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 2 and 3 until desired tension is achieved NOTE If changing from a smaller display to a larger display it may be necessary to increase swing arm tension Socket Head Cap screw Figure 14 Increase Figure 15 Installation Instructions PDR Series Removing Display from Mount 1 Remove bolt or padlock from faceplate if used NOTE The pin may have been used as a more permanent locking device If so remove nut and pin and move from the lower holes to the upper holes 2 Pull back on flag on upper mounting hole and press pin down into Open position See Figure 16 WARNING DISPLAY MAY WEIGH IN EXCESS OF 40 LBS Always use two people and proper lifting techniques when
11. part on center See Figure 1 Figure 2 Adjusting PDR Height NOTE Height adjustment range up to 1 08 inches 1 Check PDR for the desired height If needed use the adjustment wrench E to adjust the PDR height See Figure 3 Turn adjustment nut clockwise to lower the unit height or e adjustment nut counterclockwise to raise the unit height Figure 1 3 Place and level mount against wall aligning mounting holes in upper and lower wall channels with studs See Figure 1 4 Mark four mounting holes making sure mounting holes are located as close as possible to center of studs See Figure 1 5 Drill four 7 32 pilot holes where the mounting holes were marked See Figure 1 6 Partially install two 5 16 x 3 1 2 lag bolts into upper pilot holes DO NOT tighten at this time See Figure 2 7 Align mounting holes in upper wall channel with lag bolts and hang mount on lag bolts 8 Adjust mount lateral position left until lag bolts are seated in mounting slots in upper wall channel See Figure 2 Installation Instructions PDR Series o E o aem Neos c0 6 5 F
12. t or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the PDR does not exceed 200 Ibs 90 7 kg Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury PDR Series contains the following models e PDR2000S PDR2000B e PDRUS PDRUB NOTE CUSTOM INTERFACE BRACKET NOT SHOWN THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY Mounting Pattern WILL ADD BETWEEN 1 2 AND 2 IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY 483 ON THE MOUNT 19 00 SEE PSB XXXX DRAWING ALSO 178 25 11 700 21 125 57 _
13. ts Vertical Tilt Tension Adjustment 1 With display mounted check for desired vertical tilt tension 2 Adjust the Centris Select knob until desired vertical tilt Mna alt tension is obtained See Figure 8 ock screw 3 To lock the mount at the desired vertical tilt tighten the vertical tilt lock screw See Figure 9 Figure 9 Installation Instructions PDR Series Lateral Tilt Tension Adjustment A CAUTION DO NOT OVERTIGHTEN LATERAL TILT ADJUSTMENT NUT Overtightening lateral tilt adjustment will cause excessive wear and may distort adjustment components 1 Using a 9 16 wrench not provided slightly tighten or loosen lateral tilt tension adjustment nut See Figure 10 2 Attach the display and check for desired tilt tension 3 Repeat Steps 1 and 2 until desired tilt tension is obtained Rotational Tilt Tension Adjustment 1 If necessary loosen or tighten bottom rotational tilt tension adjustment nut See Figure 10 2 Attach the display and check for desired rotational tilt tension 3 Repeat Steps 1 and 2 until desired rotational tilt tension is obtained P e fe L Lateral Tilt Adjustment Nut e Rotational Tilt Adjustment Nut Figure 10 Swing Arm Adjustments The dual swing arms are shipped install
Download Pdf Manuals
Related Search