Black Box LPS500A-MM-LC network media converter
Contents
1. D 4 x 15 8 x 13 3 cm NOTE To connect this device to a router bridge or switch refer to the corresponding device s user s manual Page 6 724 746 5500 blackbox com Chapter 2 Overview 2 Overview 2 1 Introduction Use the PoE PSE Media Converter 10 100 1000BASE T to 1000BASE SX LX to connect two types of network segments easily and inexpensively It complies with IEEE 802 3af power over Ethernet PoE standard The AC powered PoE media converter is power sourcing equipment PSE that combines data received over a twisted pair link with 48 VDC providing power to an IEEE 802 3af powered device PD over the existing CAT5 UTP cable The media converter includes PD signature sensing and power monitoring It also features overcurrent protection undercurrent detection and fault protection input The Link Fault Passthrough LFP allows the media converter to monitor both the fiber and copper RX ports for loss of signal In case of a loss of RX signal on one media port the converter will automatically disable the TX signal to the other media port passing through the link fault Far End Fault FEF enables the converter to stop sending link pulse to the link partner once a loss of the fiber RX signal is encountered Then the link partner will synchronously stop sending data FEF prevents loss of valuable data transmitted over an invalid link Available models include e LPSSOOA MM SC PoE PSE Media Converter 10 100 1000BASE T to 1000BA2. usado nicamente con carritos o pedestales que sean recomendados por el fabricante El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra o superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u otros aparatos incluyendo amplificadores que producen calor El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato Precauci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato El equipo el ctrico debe ser limpiado nicamente de a
3. A 6 A RO A RR abate 7 ZA Into dC A A ta 7 A LR RO 7 223 Whats Inu dd cli 8 ZA NEON tano Baca AMG stat na E da de ra io snes leo didas 8 25 LED CS a aida 9 2 6 Side Panel DIP Switches and Reset BUTON iisiccccscsssooncnaseasncstcnotacnseade red a added ad a ilatina 9 A RARO 11 3 1 C nnecting HardWare ii A ad ida 11 3 2 POE Endpoint RJ 45 Pin ASSIGHIMEME ee ciissintasienrnenin cian cadacanendoadetuhesdnad vi qaensandan SES Ea E ea Ne ea aa dati Aqua sde Ascer 12 4 Link Fault Passthroug Mirian ota tog 13 5 Gable Connection Parameters ula iii 15 724 746 5500 blackbox com Page 5 PoE PSE Media Converters 10 100 1000BASE T to 1000BASE SX LX 1 Specifications Data Transfer Rate 1000 Mbps 1 488 000 pps 100 Mbps 148 800 pps 10 Mbps 14 880 pps Fiber Cable 50 125 62 5 125 or 100 140 um multimode 8 3 125 8 7 125 9 125 or 10 125 um single mode Flow Control IEEE 802 3x compliant for full duplex backpressure flow control for half duplex PSE Power Feeding Supports Endpoint via twisted pair Pins 1 2 3 6 Standards IEEE 802 3u 10BASE T 100BASE TX 100BASE FX IEEE 802 3z ab 1000BASE T IEEE 802 3af Power over Ethernet UTP Cable CAT5 or better cable up to 328 feet 100 m Indicators FX 2 LEDs Power Link Act PSE TP 6 LEDs PoE SPD Link Act 4W 7W 15 4 W Power 100 240 VAC 50 60 Hz 24 W Temperature Tolerance 32 to 122 F 0 to 50 C Humidity 5 to 90 Size 1 6 H x 6 2 W x 5 3
4. May 2010 G e LPS500A MM SC LPS500A MM LC lt gt BLACK BOX LPS500A SM 10K SC LPS500A SM 10K LC NETWORK SERVICES lt sBLACK BOX d KaT 5500 gt wi piackbox com 1 724 746 5 en 200 m Couns 000BASE X j 10 100 1000BASE T PoE PSE To1 la s Media Conve PoE Power uipment er Sourcing Eq Customer Order toll free in the U S Call 877 877 BBOX outside U S call 724 746 5500 Support FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 e Inf ti Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 e JOUER tt Web site www blackbox com E mail infoO blackbox com PoE PSE Media Converters 10 100 1000BASE T to 1000BASE SX LX Federal Communications Commission and Industry Canada Radio Frequency Interference Statements This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It hasbeen tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at hi
5. Panels The media converter has one Gigabit Ethernet twisted pair port and one fiber port on its front panel It also has a Power LED on the front panel The AC power input connector is on the back panel 4w 0 LNK ACT 7w O srp LNK ACT 15 4W O PoE O Pwr PSE TP y L_ FX l Figure 2 1 Front panel Figure 2 2 Back panel Page 8 724 746 5500 blackbox com Number BR W N 2 5 LED Indicators LED FX LNK ACT TP LNK ACT TP SPD PWR PoE PSE TP 4W TW 15 4W 2 6 Side Panel DIP Switches and Reset Button Chapter 2 Overview Table 2 1 Front and back panel components Component RJ 45 port LED indicators 2 SC or LC connectors 3 prong power outlet Description Links to twisted pair Gigabit Ethernet Described in Table 2 2 Links to fiber Links to power cord Table 2 2 Indicators and their functions Color Green Green Green Amber Green Green Red Green Green Green Function Lit when fiber connection is good Blinks when fiber data is present Lit when TP connection is good Blinks when TP data is present Lit when TP speed is 1000 Mbps Off when TP speed is 100 or 10 Mbps Lit when TP speed is 100 Mbps Off when TP speed is 1000 or 10 Mbps Lit when 5 V power is coming up Lit when PoE input power is active Lit when PoE input power is disrupted caused by overtempera ture overcurrent Lit when PD Class Type is Class 1 Lit when PD Cla
6. SE SX SC connectors multimode fiber e LPS500A SM 10K SC PoE PSE Media Converter 10 100 1000BASE T to 1000BASE SX SC connectors single mode fiber 10 km e LPSSOOA MM LC PoE PSE Media Converter 10 100 1000BASE T to 1000BASE SX LC connectors multimode e LPS500A SM 10K LC PoE PSE Media Converter 10 100 1000BASE T to 1000BASE SX LC connector single mode fiber 10km 2 2 Features e IEEE 802 3af PoE PSE compatible e Internal AC power supply e Overcurrent protection e Undercurrent detection e Minimum load sensing e Fault protection Input e PSE MDI power enable disable e LFP and FEF e Supports one 10 100 1000BASE T Gigabit Ethernet UTP port and one 1000BASE SX LX SC LC Gigabit Ethernet fiber port e Supports 802 3x flow control for full duplex ports and backpressure for half duplex ports e Supports comprehensive types of fiber with different distances and connections including SC and LC e Supports auto mode on the twisted pair port e DIP switch to set configurations e Supports jumbo frame Normal Mode 2 KB Cut Through Mode 9 KB 724 746 5500 blackbox com Page 7 PoE PSE Media Converters 10 100 1000BASE T to 1000BASE SX LX 2 3 What s Included Your package should include the following items If anything is missing or damaged please contact Black Box Technical Support at 724 746 5500 e 1 10 100 1000BASE T To 1000BASE X PoE Media Converter e 1 AC power cord e 1 user manual on CD ROM 2 4 Front and Back
7. ble The media converter can also work as a standard media converter when PoE is disabled 3 Connect the FX port to a fiber network using the appropriate fiber cable WARNING Verify that the AC input conforms to your country s AC power requirement before inserting the power plug 10 100 1000BASE T to 1000BASE SX LX PoE Media Converter Links to PD device Links to 1000BASE X fiber network Figure 3 1 Connecting PSE PoE converter and cables 724 746 5500 blackbox com Page 11 PoE PSE Media Converters 10 100 1000BASE T to 1000BASE SX LX 3 2 PoE Endpoint RJ 45 Pin Assignment IEEE 802 3af assigns pairs on the RJ 45 connector of the CAT5 cable as shown in Figure 3 2 Endpoint 48V via twisted pair Pins 1 2 3 6 Signal Pairs 48V RJ45 Connector CAT5 Cable Figure 3 2 Endpoint PSE RJ 45 male connector Page 12 724 746 5500 blackbox com Chapter 4 Link Fault Passthrough 4 Link Fault Passthrough This converter supports link fault passthrough LFP Link status on one port is sent to the other port to identify the remote nodes If the twisted pair port is unplugged the converter stops transmission on the fiber port This causes the remote fiber node link to fail LEDs indicate the link failure on both twisted pair and fiber ports If the fiber link fails the converter restarts autonegotiation on the twisted pair port but stays in the link failure state This causes the remote twisted
8. cuerdo a las recomendaciones del fabricante En caso de existir una antena externa deber ser localizada lejos de las lineas de energia El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando El cable de poder o el contacto ha sido da ado u Objectos han ca do o l quido ha sido derramado dentro del aparato o El aparato ha sido expuesto a la lluvia o El aparato parece no operar normalmente o muestra un cambio en su desempe o o El aparato ha sido tirado o su cubierta ha sido da ada MON 724 746 5500 blackbox com Page 3 PoE PSE Media Converters 10 100 1000BASE T to 1000BASE SX LX Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies Inc Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners We re here to help If you have any questions about your application or our products contact Black Box Tech Support at 724 746 5500 or go to blackbox com and click on Talk to Black Box You ll be live with one of our technical experts in less than 20 seconds Page 4 724 746 5500 blackbox com Table of Contents Table of Contents Chapter Page E gal O CU O
9. pair node link to fail LED also indicates the link failure on both twisted pair and fiber ports Refer to Figure 4 1 for the normal status when the link succeeds Refer to Figure 4 2 and Figure 4 3 for the error status when TP Cable A Fiber Cable B or Fiber Cable C fails to connect NOTE LFP function only takes effect when S1 2 see Figure 2 3 is enabled Disabling 1 2 will turn LFP off e indicates LNK ACT LED Lit indicates LNK ACT LED Off Gigabit Gigabit Ethernet Ethernet sa switch switch station Fiber cable Figure 4 1 Normal status via a pair of LFPs Gigabit Gigabit Ethernet Ethernet delia switch LFP LFP switch an D B A TP C TP O OO fre O O O O cable Figure 4 2 The status when TP Cable A or D is broken Gigabit Gigabit Ethernet Ethernet O switch switch station Fiber cable Figure 4 3 The status when Fiber Cable B or C is broken 724 746 5500 blackbox com Page 13 PoE PSE Media Converters 10 100 1000BASE T to 1000BASE SX LX Gigabit Gigabit Ethernet Ethernet Remote Fiber switch switch station Fiber cable Figure 4 4 Normal status via one LFP Gigabit Gigabit Ethernet Ethernet Remote Fiber switch LFP switch station B C Fiber cable Figure 4 5 The status when twisted pair Cable A is broken Gigabit Gigabit Ethernet Ethernet Remote Fiber switch each station Fiber cable Figure 4 6 The status when fiber Cable B or C is broken NOTE The LFP function can work with different link par
10. s own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le Reglement sur le brouillage radio lectrique publi par Industrie Canada Page 2 724 746 5500 blackbox com In NOM Statement strucciones de Seguridad Normas Oficiales Mexicanas Electrical Safety Statement 1 2 3 4 5 oN OD oO 10 11 12 13 14 15 16 17 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas Todas las instrucciones de operaci n y uso deben ser seguidas El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc El aparato el ctrico debe ser
11. ss Type is Class 2 Lit when PD Class Type is Class O or 3 DIP switches and a reset button are on the side panel of the converter See Figure 2 3 724 746 5500 blackbox com Page 9 PoE PSE Media Converters 10 100 1000BASE T to 1000BASE SX LX yBnowyy ing da od PoE IC PoE DIS LFP W LFP DIS RESET union sid ddI CM Cm sig 30d CE Reset Button Cut through MW Normal Figure 2 3 DIP switches and Reset button on the converter s side panel Table 2 3 Side panel components and their functions Component Setting Function Reset button Press once After you change the DIP switch settings you must press the Reset button for changes to take effect DIP Switch S1 1 Bridge mode Up Cut through default mode supports jumbo frames size up to 9216 Bytes Down Normal mode supports frame size up to 2048 Bytes DIP Switch S1 2 LFP Up LFP enabled default Down LFP disabled DIP Switch S1 3 PoE ON OFF PoE ON Powering PD devices enabled default PoE OFF Not powering PD devices disabled Page 10 724 746 5500 blackbox com Chapter 3 Installation 3 Installation 3 1 Connecting Hardware The 10 100 1000BASE T PoE PSE to 1000BASE X Media Converter requires no software configuration To install the media converter follow the steps below 1 Connect the PSE media converter to an AC power source 2 Connect a PoE PD device to the PSE TP port on the media converter using the appropriate twisted pair ca
12. tners for example a fiber port on a switch You do not have to use these units in pairs for this function to work Page 14 724 746 5500 blackbox com Chapter 5 Cable Connection Parameters 5 Cable Connection Parameters 1000BASE SX LX networks only support full duplex mode The switch based media converter breaks the twisted pair and fiber segments collision domain to extend the cabling distance TP cable limitations CAT5 and up to 328 feet 100 m Mode 1000SX SC LC 850nm 1000LX SC LC 1310 nm Table 5 1 Mulltimode fiber cable limitations Multimode Fiber Multimode Fiber 62 5 125 um 50 125 um Bandwidth MHz km Distance Bandwidth MHz km Distance 160 m 220m 400 500 m Single mode fiber 9 125 um Single mode transceiver 1310 nm 10 km 724 746 5500 blackbox com Page 15 Black Box Tech Support FREE Live 24 7 Tech support the way it should be A Great tech support is just 20 seconds away at 724 746 5500 or blackbox com lt BLACK BOX About Black Box Black Box Network Services is your source for more than 118 000 networking and infrastructure products You ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free live 24 7 Tech support available in 20 seconds or less Copyright 2010 All rights reserved 724 746 5500 blackbox com
Download Pdf Manuals
Related Search