Xit XTCG6D
Contents
1. ltem XTCG6D Multi power Battery Pack User s Manual designed for PHOTO capture the spot PART NAMES 1 Protective cover 2 Electrical contacts 3 Attachment screw 4 Guide pin 5 Attach detach knob 6 Battery magazine release handle 7 DC cord mount 8 AF point selection Magnify button 9 AE lock FE lock Index Reduce button 10 AF start button 11 Vertical grip operation switch 12 Shutter button 13 Camera battery compartment cover slot 14 Main dial 15 Hand strap mount 16 Tripod socket 17 Battery chamber latch 18 Battery pack compartment 19 Battery magazine for size AA batteries The XTCG6D is a battery grip that can hold two battery pack LP E6 or six AA batteries it is also equipped with a vertical grip shutter button main dial etc to enable shooting in the same way as with horizontal grip USING THE BATTERY GRIP 1 Turning the vertical grip operation switch to lt ON gt Fig 12 makes the battery grip buttons and dial function in the same way as those on the camera 2 When shooting in the horizontal grip position turn the ATTACHING TO THE CAMERA 1 Remove the battery from the camera Fig 1 2 Pull out the camera s battery compartment cover a slanted angle to detach Fig 2 Perform the operation on a table so as not to drop the camera 3 Insert the detached cover into its storage slot to ensure that it will not be lost F2. can be checked on the camera 1 One or two battery packs LP E6 2 Six size AA alkaline batteries Camera s power switch Refer to your camera s instruction manual 0 C 40 C 32 F 104 F 85 or less Approx 145 6 W x 111 3 H x 85 3 D mm Approx 5 7 W x 4 4 H x 3 4 D in Approx 295g 10 402 without batteries and battery magazine
3. hed to the battery grip 4 Close the release handle Fig 7 2 e If only one battery pack is used it can be inserted in either the right or left side e If two battery packs are inserted power is supplied simultaneously by both battery packs Two battery packs with different charging levels can be inserted and used without any problems e Remove the battery packs or size AA batteries from the battery grip when the camera will not be used for an extended period INSTALLING SIZE AA BATTERIES 1 Insert the batteries onto the battery magazine for size AA batteries Fig 8 Make sure the and battery contacts are properly oriented as shown in the illustration 2 Attach the battery magazine into the battery grip Fig 9 1 After attaching check that the battery magazine is securely attached to the battery grip 3 Close the release handle Fig 9 2 e Fewer images can be shot when using size AA batteries Also the number of possible shots may vary depending on the batteries brand and storage conditions So age of size AA batteries is recommended only for emergencies e With size AA batteries use six new batteries of the same brand at temperature above 20 C 68 F the camera may not function when used in lower temperature or when old and new batteries are used together vertical grip operation switch to lt OFF gt so that you do not accidentally use the buttons or dial on the battery grip 3 The battery level
4. ig 3 When taking out the cover press lightly on the cover hinge and pull it out upward at a slanted angle Fig 3 2 4 Remove the protective cover and then insert the electrical contacts into the camera battery compartment Fig 4 1 5 Align the attachment screw with the camera s tripod socket And then turn the attach detach knob to tighten securely Fig 4 1 SPECIFICATIONS Battery Power switch Possible shots Working temperature range Working humidity e Do not further push open the battery compartment cover when it is already open doing so may damage its hinge e Be sure to attach the battery grip to the camera before inserting the batteries The results of the battery check may not be displayed properly if you attach the battery grip to the camera Dimensions with the batteries already inside e Before removing the battery grip from the camera make sure to turn the camera s power switch to lt OFF gt and take out the batteries After removing the batteries attach the protective cover to the electrical contacts INSTALLING THE BATTERY PACKS 1 After flipping out the release handle turn it as shown by the arrow Then pull out the battery magazine for size AA LR6 batteries Fig 5 2 Insert one or two battery pack LP E6 into the battery magazine for LP E6 Fig 6 3 Attach the battery magazine into the battery grip Fig 7 1 After attaching check that the battery magazine is securely attac
Download Pdf Manuals
Related Search