Panduit S6512B racks
Contents
1. For Technical Support www panduit com resources install maintain asp Page 16 of 22 INSTRUCTIONS CM599D PDU Bracket Adjustment e PDU brackets are height adjustable if PDU spacing other than the factory position is desired e Remove 2 M5 Torx Screws per bracket as shown below e Reposition brackets at desired distance ensuring that mounting flange of PDU bracket rests on the outside of cabinet post See Installed view below e Secure each PDU bracket to cabinet post with 2 M5 Torx Screws per bracket Top PDU Bracket 2 M5 Torx Screws use T25 Torx bit PDU Bracket installed J 9 Bottom PDU Bracket 2 M5 Torx Screws use T25 Torx bit For Technical Support www panduit com resources install maintain asp Page 17 of 22 INSTRUCTIONS CM599D Front and Rear Floor Seal Installation Vertical Exhaust Duct ONLX e Install Floor Seal to front or rear of cabinet frame using 2 M10x20mm Bolts Flange on floor seal will face outward away from the cabinet 2 M10x20mm Bolts use 15mm socket wrench For Technical Support www panduit com resources install maintain asp Page 18 of 22 INSTRUCTIONS CM599D Cabinet Seal Kit Installation Switch Configured S Tvpe Cabinets ONLY e Install Horizontal Blanking Pan2. Sealing i da ita gia str G a al it sags a R PDU Bracket ATEN it ieli b a Se Front and Back Border Cabinet Seal Kit Installation 25 iii iu d re a id a g ee t ba re Ta i Top of Cabinet Cable Manager Installatieti asaasemrdrsuant rehosktemmd tat ng Top of Cabinet Cable Manager Installation for vertical exhaust ducts 2 eee For Technical Support www panduit com resources install maintain asp Page 3 of 22 INSTRUCTIONS CM599D Packaging Material Removal Before removal of packaging material Check tip indicator on the outside of cabinet to ensure cabinet was shipped in the upright position If tip indicator shows improper handling inspect cabinet for damage before accepting cabinet Before handling cabinet Small glide strips are installed at various locations around the cabinet to protect the cabinet s finish during shipping These strips are to be removed prior to handling of cabinet Shipping Hold Down Bracket Doubles as Floor Mounting Bracket Retain bracket if floor mounting is desired see Page 6 e Remove all stretchwrap and protective cardboard from outside of cabinet e Remove all Shipping Brackets if necessary e Remove 2 Hold Down Brackets at front and rear of cabinet e Use 2 people to carefully lift and remove cabinet from pallet IMPORTANT Leveling Legs must be fullv retracted before the cabinet is moved into place Sliding cabinet on leveling legs mav result in damage to the leve
3. flat surface VIEW 4 5 e Remove Door Handle Backing Plate and rotate position of Door Handle 180 e Loosen Cam Screw to reposition Door Cam and Cam Stop to outside of door Tighten Cam Screw e With Door Handle repositioned secure Door Handle Backing Plate to Door Handle e Remove PANDUIT label and re attach in correct orientation near top of door e Reinstall Single Hinge Door per instructions on Page 12 2 M4 Screws use 2 5mm Allen Key Top Hinge Bracket M6 Torx Screw use T30 Torx bit Bottom Hinge Bracket Door Catch Door Handle Backing 2 Hex Nuts Plate use 8mm socket wrench Door Cam reposition to outside edge of door Door Handle rotate 180 PANDUIT Label For Technical Support www panduit com resources install_maintain asp Page 13 of 22 INSTRUCTIONS CM599D Rear Split Doors Removal and Installation e Open Rear Split Doors to approximately 90 e Lift Rear Split Doors up pull doors away from cabinet frame e REVERSE STEPS to install Rear Split Doors sfx as a a aE Ell SOA 00 OO9 0 099 00900 9 00 500 9 00 900909 9 00099 9 005050 900990 000 9 00009 95 009990 099 005009 095600 9 00 509009 le Dl do For Technical Support www panduit com resources install maintain asp Page 14 of 22 INSTRUCT
4. inward to lock in place NAP p0 205 2 009 202 000 00 0 20 2 00 2 00 2 20 2 20 0 00 2 202 00 2 00 2 002 00 0 00 0 00 0 00 0 00 0 20 2 00 0 00 0 00 2 00 0 00 0 00 2 000 00 0 00 2 00 Aa 22002000 000 000000 000 00000000 i For Technical Support www panduit com resources install maintain asp Page 11 of 22 INSTRUCTIONS CM599D Single Hinge Door Removal and Installation e VIEW 1 Pull down Compression Sleeve at top door hinge e VIEW 1 Pull Single Hinge Door away from cabinet so that Top Hinge Screw fits through cutout of door e VIEW 2 Lift bottom of door off Bottom Hinge Pin e REVERSE STEPS to install Single Hinge Door Top Hinge Screw Compression Sleeve Pull down VIEW 3 Bottom Hinge Pin For Technical Support www panduit com resources install_maintain asp Page 12 of 22 INSTRUCTIONS CM599D Single Hinge Door Door Handle Direction Reversal e VIEW 1 2 Remove Top and Bottom Hinge Brackets from current location remove top hinge screw if necessary VIEW 1 2 Install Top and Bottom Hinge Brackets on opposite side of cabinet re install top hinge screw if necessary e VIEW 3 Move Door catch to opposite side of cabinet frame Door Handle Reversal Lay door on a
5. CM599D READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET rrom ski an D U l NET ACCESS S Tvpe Server Cabinets Server Configurations INSTRUCTIONS CM599D O Panduit Corp 2013 NOTE Some views in this document may vary slightiv from vour actual cabinet configuration Tool List Phillips screwdriver Flatblade screwdriver 22mm socket wrench 15mm socket wrench 13mm socket wrench 8mm socket wrench 7mm socket wrench T30 Torx bit T25 Torx bit 6mm Allen Key 2 5mm Allen Key Wire Cutter FOR TECHNICAL SUPPORT www panduit com resources install maintain asp Page 2 of 22 INSTRUCTIONS CM599D Table of Contents Net Access S Tvpe Network Cabinets General Cabinet Operation Packaging Material Removal ke A e beads iernae Sousa BEE l a EEE T EN E EN Floor Mounth stedise konie A a A A e AE EA GE et NS NG Gods Lunnan vestene ape unner eee Equipment RalAdjustment uuussasmrsvemersit mi 6 tate auecemaletedseaeaes Overhead Cable Openings sa il van aed E ue towiates Cable Management Fingers Installation SNISF SN25F e cee ce cence eee eens Single Hinge Door Removal and Installation eeennennzzennnnennznnnnnnnni Rear Split Doors Removal and Installation ss eeneennnennnnennnkannnennzzennni In Row Side Panel Removal and Installation sse senenennzenenzzannnnzannnnnzz Cabinet
6. IONS CM599D In Row Side Panel Removal Installation and Adjustment optional e Pul 2 Spring Loaded Hinge Pins to release Rear Side Panel from cabinet frame e Pull 4 Spring Loaded Hinge Pins to release Front Side Panel from cabinet frame e REVERSE STEPS to install In Row Side Panels IMPORTANT Install Front Side Panel First Spring Loaded Hinge Pins Spring Loaded Hinge Pins 2 Locations 2 Locations Spring Loaded Hinge Pin Top and Bottom Move Finger Pull into Slot to Lock Hinge Pin in OPEN position Ny ai z Vn a m r TY ae aN Rear Side Panel Adjustment Bushing Adjust Fit of Side Panels Use included wrench to raise or lower adjustment bushings Adjustment Wrench included Side panels removed from view to add clarity For Technical Support www panduit com resources install_maintain asp Page 15 of 22 INSTRUCTIONS CM599D Cabinet Sealing Install 6 Latch Plugs 3 upper and 3 lower into the door latch cut outs to the front side of the cabinet only Install 2 foam seals to the upper and lower frame Seal should be pressed up against the Equipment Rails behind the latch plugs 3 Latch Plugs Foam Seal Foam Seal 3 Latch Plugs
7. Torx bit Re install screws from previous step to secure to the frame e Attach front fascia to the front vertical wall by sliding fascia over studs in vertical wall see detail view Tighten with 4 M5x0 8 but ton head screws use T25 Torx bit Attach rear fascia to the rear vertical wall by sliding fascia over studs in vertical wall see detail view Tighten with 4 M5x0 8 but ton head screws use T25 Torx bit 2 Vertical Walls Remove 4 M5 Torx Screws use T25 Torx bit 5 M5 Torx Screws Rear Fascia use T25 Torx bit Front Fascia 2 Vertical Walls 4 M5 Torx Screws use T25 Torx bit For Technical Support www panduit com resources install_maintain asp Page 20 of 22 INSTRUCTIONS CM599D Top of Cabinet Cable Manager Installation for vertical exhaust ducts IMPORTANT INSTALL VERTICAL EXHAUST DUCT PRIOR TO INSTALLING REAR VERTICAL WALL e Disassemble front fascia assemblies packaged in cabinet by removing 2 M5x0 8 button head screws use T25 Torx bit e Remove 2 M5x0 8 button head screws use T25 Torx bit from front of Cable Manager base e Install vertical wall on front of Cable Manager base using 5 M5x0 8 button head Torx screws use T25 Torx bit Re install screws from previous step to secure to the frame e Attach front fascia to the front vertical wall by sliding fascia over studs in vertical wall see detail view Tigh
8. e to outside of cabinet UIT III Equipment Rail M10 Hex Head Screw Mount Nut use 15mm socket wrench MITIMITIT MUNIT IT MLITI IMLITIT MLIUITIT MLIT IT ILUTIT MLITITM Slot of Front to Back Beam HA 704 M10 Hex Head Screw use 15mm socket wrench For Technical Support www panduit com resources install maintain asp Page 9 of 22 INSTRUCTIONS CM599D Overhead Cable Openings Remove Bezel Insert to allow for overhead cable entrv e Cut 8 tabs with wire cutter to open large cable openings OPTIONAL e Install M10 threaded rod into 6 tapped holes if desired e 21 152 4mm x 152 4mm 6 x 6 openings can be used to route power overhead e PANDUIT Coot Boot products can be used to seal around cables fiber to prevent hot air recirculation 6 M10 Threaded Holes Removable Insert Overhead Cable Opening Bezel N Bezel 3 v 8 gt 2 152 4mm x 152 4mm Openings 6 x 6 pi Sa OPTIONAL For Technical Support www panduit com resources install maintain asp Page 10 of 22 INSTRUCTIONS CM599D Cable Management Fingers SN15F SN25F e Insert tabs of Cable Management Finger into mounting slots of cabinet post e Slide Cable Management Finger inward to lock into place a M Cable Managment Finger Insert tabs into cabinet post Slide
9. el so that front face aligns with equipment rails Install 2 Bottom Seal Brackets Left Bracket is noted by diamond cutout Attach D shaped Rubber Seal to Horizontal Blanking Panel Attach 25mm x 50mm Foam Seals to bottoms of Horizontal Blanking Panel and 2 Bottom Seal Brackets Example part number S8512BA D Shaped Rubber Seal 2 M5 Torx Screws use T25 Torx bit Horizontal Blanking Panel align with equipment rails 16 3 j DO U alle A pE 2 M5 Torx Screws ki q B use T25 Torx bit e B Je TE 9 NY I d 3 LT S ah A lt i 1 l d A 4 ve d i q o c i Jer Z de tul 17 5 i z ale HS PER i 0 o Seal Bracket note diamond s cutout LEFT Bottom Seal Bracket 25mm x 50mm Foam Seals For Technical Support www panduit com resources install_maintain asp Page 19 of 22 INSTRUCTIONS CM599D Top of Cabinet Cable Manager Installation e Disassemble front fascia assemblies packaged in cabinet by removing 2 M5x0 8 button head screws use T25 Torx bit e Remove 2 M5x0 8 button head screws use T25 Torx bit from front and rear of Cable Manager base e Install vertical walls on front and back of Cable Manager base using 5 M5x0 8 button head Torx screws use T25
10. etracted e If Necessary secure 2 Shipping Hold Down Brackets at front and rear of cabinet e See Floor Mounting View below for floor mounting dimensions e Attach the anchors to the floor with appropriate hardware for your type of floor 2 Shipping Hold Down Brackets 4 M10 Hex Head Screws use 15mm socket wrench l Floor Mounting View O e U m Q n 173mm ologe ogs 6 79 g b DIM A 1070mm deep cabinets 699mm 27 52 jfr i 1200mm deep cabinets 581mm 33 51771 l i DIMA DIM B 9 P 600mm wide cabinets 191mm 7 52 EA IE 700mm wide cabinets 241mm 9 48 4X 14mm DIA 800mm wide cabinets 291mm 11 46 0 55 9 b For Technical Support www panduit com resources install maintain asp Page 6 of 22 INSTRUCTIONS CM599D Ganging e Ensure cabinets are level e Secure Ganging Brackets to cabinets at 4 locations shown below Do not use Ganging Brackets to cinch cabinets together IMPORTANT Ensure cabinets are level by following the guidelines on page 5 Leveling the cabinet prior to ganging is important to ensure proper door operation 4 Ganging 7 l Fi 2 g Brackets AT z ke gt biez zz 8 M6 Torx Screws use T25 Torx bit 9 7 je alli wel si L B G a F ke 0 e ll gt i gig L a oe a bi ki For Tec
11. hnical Support www panduit com resources install maintain asp Page 7 of 22 INSTRUCTIONS CM599D Grounding e Attach Grounding Lug or Grounding Bar at any of the 6 location s shown below e Grounding location is indicated by universal ground symbol e Use M5 bonding screw 8 Grounding Lug Locations Front and Rear of Beams Note top cap removed for clarity For Technical Support www panduit com resources install maintain asp Page 8 of 22 INSTRUCTIONS CM599D Equipment Rail Adjustment e Loosen M10 Hex Head Screw at top and bottom of rear equipment rail e Adjust equipment rail to desired positon e Tighten M10 Hex Head Screw to 30 0 5 0 N m 22 1 3 7 Ft Ibs NOTE Front equipment rails are in a fixed position Uninstall Re install and Move Equipment Rails Top and Bottom Locations e Remove 2 M10 Hex Screws at top and bottom of Equipment Rail e Remove 2 Equipment Rail Mount Nuts through slots of Front to Back Beam e REVERSE STEPS to re install Equipment Rails insert Equipment Rail Mount Nuts through slots of Front to Back beam while holding finger grip of mount nut ensure that barbed surface of Equipment Rail Mount Nut faces outside of cabinet M10 Hex Head Screw use 15mm socket wrench Equipment Rail rT Mount Nut Finger Grip Area Fr Po MLIT ME l l l l l l l l l l l Barbed Surface fac
12. ling legs Leveling Legs ship in retracted position list Front Door l 2 Side Panel 6 M5 Hex Screws L J Shipping Bracket Shipping Brackets use 7mm socket wrench A La pi 2 M14 Hex Nuts i use 22mm socket wrench a 8 M10 Hex Head Screws T use 15mm socket wrench lt N A 4 Lag Screws and Washers i use 13mm socket wrench Pallet 2 Shipping Hold Down Brackets Note Doors Side panels and other components are removed for clarity For Technical Support www panduit com resources install_maintain asp Page 4 of 22 INSTRUCTIONS CM599D Leveling e Ensure that 4 Leveling Legs are fully retracted e Slide Cabinet into final position e Lower the 4 Leveling Legs until the cabinet weight is fully supported e Adjust the 4 Leveling Legs so that the cabinet is level front to back and side to side Front to Back Cabinet Leveling 4 Leveling Legs use 6mm Allen Key Side to Side Cabinet Leveling Note When ganging multiple cabinets together ensure that adjacent cabinets are adjusted to the same height For Technical Support www panduit com resources install maintain asp Page 5 of 22 INSTRUCTIONS CM599D Floor Mounting e Ensure that 4 Leveling Legs are fully r
13. ten with 4 M5x0 8 but ton head screws e Attach rear vertical wall to the Cable Manger with 4 M5x0 8 button head screws use T25 Torx bit from underneath Top of Cabi net Cable Manager Front Vertical Wall Remove 2 M5 Torx Screws use T25 Torx bit 5 M5 Torx Screws W use T25 Torx bit Front Vertical Wall 4 M5 Torx Screws use T25 Torx bit Rear Vertical Wall IMPORTANT VERTICAL EXHAUST DUCT MUST BE INSTALLED PRIOR TO INSTALLATION OF REARVERTICALWALL 4 M5 Torx Screws use T25 Torx bit For Technical Support www panduit com resources install_maintain asp Page 21 of 22 INSTRUCTIONS CM599D This page is left intentionally blank For Instructions in Local Languages and Technical Support www panduit com resources install maintain asp PANDUIT www panduit com E mail techsupport panduit com Phone 866 405 6654 Page 22 of 22
Download Pdf Manuals
Related Search