Gembird EGM-PWM-LAN
Contents
1. 4 Gembird www gembird ua 044 4510213 48 All brands and logos are register2. 2 3
3. 4 20 1 2 3
4. EGM PWM LAN Please configure antivirus firewall to permit connection to the IP address and port of your EGM PWM LAN All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE Se 3 3 IP configuration The utility LAN Find see Figure 4 below will run automatically during the software installation but it can also be started from Start All Programs Gembird Power Manager The IP range where you would like to search for EGM PWM LAN will be set automatically according to the IP settings of your LAN adapter but can be changed manually in the Adapter subnet fields Now press the Search button NOTE only EGM PWM LAN within a local subnet can be found If your computer LAN adapter is not in the default subnet of EGM PWM LAN as might probably be the case if you chose option B section 3 1 you will have to change its IP address manually to be able to find EGM PWM LAN For example if you wish to find EGM PWM LAN with the default IP 192 168 0 254 the IP address of your computer should be set as 192 168 0 XXX where XXX stands for any digit for example 1 and the subnet mask should be 255 255 255 0 After the searching the IP addresses of the found EGM PWM LAN devices will appear in the list box Select EGM PWM LAN which you want to access and press the Open button see Figure 4 below 10 All brands and logos are registered trademarks of their respective owners
5. Note Read Chapter 10 below if you wish to customize these indicators 32 All brands and logos are registered trademarks of their respective owners energenie EGM PWM LAN ENERGY METER WITH LAN INTERFACE Figure 15 anl x Push Maximize button in this window to open the full size Power Meter window see Figure 16 below Figure 16 33 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w This window displays all the measured values Real power P Active impedance R Frequency of current Fq Energy consumed E The cost of energy consumed money sign RMS voltage V rms Peak voltage V peak RMS current I rms Peak current I peak It is beyond the scope of this manual to explain the physical meaning of these values For most consumers the energy and its cost are the most interesting The Energy E value shows the accumulated energy consumption in watt hours since a certain date the last time when Reset button was pressed This date is shown below the Cost display The Cost value is based on the amount of energy consumed and the energy costs Push the Set button near the Cost value to specify the energy costs for your home or office situation see Figure 17 below By Pushing the Reset button both Energy and Cost counters will be reset to zero 34 All brands and logos are registered trademarks of their respecti
6. 192 168 2 20 Power W D Energy Day WH 21 Energy Night WH 0 24 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w This page will automatically update itself and will keep showing you the time when your device was last seen online the latest time when the device communicated with the server external IP MAC address link to device web interface this link works in case that your computer is in the same local network with the device Values of Real Power Watts and Day and Night Energy Watt Hours will be shown In single tariff mode the whole energy is shown as Energy Day parameter To open real time chart window click on the Power or Energy value To change your account settings click your user name Click the device name to change its name and or transfer it to another account The Last seen online status information lets you check if the device keeps communicating with the server 25 All brands and logos are registered trademarks of their respective owners energenie EGM PWM LAN ENERGY METER WITH LAN INTERFACE Figure 11 energenie User 99 Log out Device2 Power W ivacy 2011 energenie com All rights reserved 26 All brands and logos are registered trademarks of their respective owners energenie EGM PWM LAN ENERGY METER WITH LAN INTERFACE 6 Adding the EGM PWM LAN be able to manage installe
7. e HS strongly recommended to avoid damp or wet places for installation e EGM PWM LAN should be connected to the European AC wall socket of the standard DIN 49 440 e possible to connect the EGM PWM LAN to the power source via other multi plugs surge protectors voltage regulators or UPS 3 1 Preparing LAN configuration of EGM PWM LAN Before configuring EGM PWM LAN hardware settings please let it obtain its IP address Follow the steps below e Make sure EGM PWM LAN is connected to the local network with the provided RJ 45 cable option A recommended All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE Sy NOTE by default the factory setting of EGM PWM LAN is DHCP enabled If your LAN has a router with built in DHCP server which is very common then EGM PWM LAN will automatically get an IP address from the DHCP server Proceed to section 3 2 below in this case NOTE you may prefer to connect EGM PWM LAN directly to the managing computer LAN adapter network card using the supplied crossover RJ 45 cable option B You might need to use this option if your LAN does not have DHCP server If you choose for option B then the following procedure is required to let EGM PWM LAN obtain a fixed IP address e Power EGM PWM LAN e Press Reset button on the side control panel see Figure 2 above with the tip of a pen e Holding it presse
8. energe nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE w Figure 4 LAN Find Connect device to the LAN or directly to this PC via LAN interface If you performed hardware reset of device wait for 10 seconds Where to search Adapter subnet Adapters C Hamachi From Local Area Connection 3 gt Search Stop The search has been completed IP addresses of the found devices Open The window of your default internet browser will be then opened to give you access to the built in web server See section 4 below for the further details 11 All brands and logos are registered trademarks of their respective owners energe NIE ENERGY METER WITH LAN INTERFACE w 4 The web server Your EGM PWM LAN is equipped with a web server which allows managing the device using any web browser such as Internet Explorer etc 4 1 Web server login page To access the web server of EGM PWM LAN just open Internet Explorer or other browser and input the IP address of EGM PWM LAN for example http 192 168 1 241 If you have used LAN Find utility to locate EGM PWM LAN then you will be taken to this webpage automatically Login page will then be displayed see Figure 5 below NOTE Java script must be enabled in your Internet Explorer or another browser settings Otherwise you get an error message WARNING JAVASCRIPT IS DISABLED Figure 5 EnerGenie Web Server 1 Password Enter The defau
9. ENERGY METER WITH LAN INTERFACE w button on the Login page to create a new account After your successful login regardless whether you created a new or used an existing account your EGM PWM LAN is automatically registered e Return back to the EnerGenie page of your EGM PWM LAN see Figure 6 below Push Activate button to let the device initiate communication with EnerGenie com server The EnerGenie page will then start updating itself until the Status becomes Registered Activated Connected see Figure 6 below 14 All brands and logos are registered trademarks of their respective owners energenie EGM PWM LAN ENERGY METER WITH LAN INTERFACE Figure 6 Server 1 Voltage 220 2 V Current 0 90 A ene rge Power 197 1 W Load present Energy 0 0 kWh Single mode 5 Since 01 01 2010 03 00 00 EnerGenie Time on device 01 01 2010 03 00 39 Device Settings Synchronized with NTP 01 01 2010 03 00 00 LAN Settings Tan Your EnerGenie account Activate Login Status Registered Not activated After a successful registration and activation the button Register will be renamed to Login and will then open the Login page of EnerGenie com and the button Activate will turn into Deactivate If by any reason you would eventually decide to stop managing your 15 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE Sy EGM PWM LAN from Internet use t
10. chez un centre autoris pour le traitement des appareils lectriques ou lectroniques 45 All brands and logos are registered trademarks of their respective owners energe DIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w WARRANTY CONDITIONS GARANTIE BEDINGUNGEN g The warranty period is 24 months and begins with the sale to the end user The receipt must clearly list the date of purchase and the part number in addition it should be printed Keep the receipt for the entire warranty period since it is required for all warranty claims During the warranty period the defective items will be credited repaired or replaced at the manufacturer s expense Work carried out under the warranty neither extends the warranty period nor starts a new warranty period The manufacturer reserves the right to void any warranty claim for damages or defects due to misuse abuse or external impact falling down impact ingress of water dust contamination or break Wearing parts e g rechargeable batteries are excluded from the warranty Upon receipt of the RMA goods Gembird Europe B V reserves the right to choose between replacement of defective goods or issuing a credit note The credit note amount will always be calculated on the basis of the current market value of the defective products Die Garantie betr gt 24 Monate ab Verkaufsdatum an den Endverbraucher Das Kaufdatum und der Ger tetyp sind durch eine masch
11. energe DIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w this parameter exceeds a certain maximum fill in the Max field then If you wish the event to be triggered when the value of this parameter drops below a certain minimum fill in the Min field Secondly you select the desired action from the Action list box If you choose to execute a specific application or program you can select the path to this application in the Path field It is possible to give the event a practical name in the Name field Select the Use growth checkbox if you are interested in the difference between the current value of the parameter and its previous value rather than in its absolute value Tip Use growth checkbox might be particularly useful if you wish to do something whenever a certain device gets switched on or off 42 All brands and logos are registered trademarks of their respective owners energe NIE ENERGY METER WITH LAN INTERFACE w 11 Troubleshooting The status of EGM PWM LAN Try to ping the device see section 6 1 in Power Manager does not above become Connected Reset EGM PWM LAN by pressing the E Reset button on the side control panel see Figure 2 above or switch it off and then on again using the Main rocker switch Z see Figure 1 above Make sure EGM PWM LAN is connected Connection to EGM PWM LAN to LAN and switched on Launch LAN Find is lost It seems something is utility You can also
12. interval Fe 12 Calculate i AN 0 days 00 hrs 03 mins gt NNA 18 09 53 End Total money ri spent 37 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w The horizontal axis represents the date time and the vertical axis represents the values of the chosen parameter Note The scale of the vertical axis changes automatically once you browse or zoom the chart The scale will be chosen in such a way that all the values within the displayed time period fit onto the screen Some extra tools are placed under the chart e From the Displayed value list box you can choose the value which you wish to display in the graph area e The displayed chart normally shows the average values of the chosen parameter You can determine the data point density with the Graph details level slider With this slider you actually change the number of points within the chosen time interval for the averaging Fewer points mean less details and a smoother chart More points mean more details and a more precise chart The Sum tool is used to calculate energy statistics within a selected time period Push the 2 button to activate this feature and then select a time period on the chart area by dragging and dropping with the left mouse button Doing so you will select the period as shown on the Figure 8 below The chosen period will be s
13. EGM PWM LAN ENERGY METER WITH LAN INTERFACE USER MANUAL HANDBUCH HANDLEIDING MANUEL DESCRIPTIF energe DIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w Energy meter with LAN interface Energiemessger t Energiemeter met LAN interface Compteur d nergie avec interface LAN 222 00 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w 1 1 Features e LAN Energy Meter accessible from anywhere within your LAN creates insight in your energy consumption voltage current power e Get your power consumption curves via Internet no permanent computer connection required e No external IP address at home No problem Your own user account on EnerGenie com will let you view and analyze the energy costs via Internet with any PC or even mobile phone e Power Meter software provides basic power consumption readings home use and advanced readings business scientific use 1 2 Specifications Input 220 240 V AC 50 60 Hz Load max 10 A Power consumption max 1 4 W e Computer measurements voltage and current measuring RMS values true p
14. ER WITH LAN INTERFACE w IP address Subnet mask Gateway DNS server will be used only if the DHCP option is disabled If you set DHCP option it is recommended for your own convenience to set up your DHCP server so that it always provides the same IP address to EGM PWM LAN To do that you will need to know the MAC address of EGM PWM LAN It can be found on this page or on the bottom sticker of the device The MAC address is fixed and cannot be changed DNS server address is important to be properly set up in case you wish to enable the NTP timer correction option see section 4 4 below IP filter option is needed to prevent unauthorized access to the server It restricts the web server access from any computer with IP address different from IP1 IP2 and IP3 Make sure that you input IP1 IP2 and IP3 correctly before enabling this option Power Manager client port is used for connecting with the Power Manager software normally it is not needed to change this setting 18 All brands and logos are registered trademarks of their respective owners energenie EGM PWM LAN ENERGY METER WITH LAN INTERFACE 4 4 Device settings page On the device settings page you can setup name password and internal time of EGM PWM LAN see Figure 8 below Server 1 1 energenie EnerGenie Device Settings LAN Settings Log Out Figure 8 Device settings Server name Server 1 Password Set device time Use NTP for timer m correctio
15. cess your EGM PWM LAN from anywhere in the world using any Internet enabled device desktop PC laptop smartphone etc See section 4 2 above on how to register your EGM PWM LAN on the server and setup the connection 5 1 Logging in To login into your EnerGenie account just open the webpage www energenie com user in your Internet browser and enter your login and password in the login window see Figure 9 below If you are a new user click New account button then fill user profile form 22 All brands and logos are registered trademarks of their respective owners ene rge nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE w Figure 9 energenie Login Jonn Password m CES zd Check Remember me checkbox for automatic login in the future the website will then save a cookie on your computer If you lost your password click Forgot password button 5 2 Device management page After a successful login you will see the list of your registered devices see Figure 10 below 23 All brands and logos are registered trademarks of their respective owners energenie EGM PWM LAN ENERGY METER WITH LAN INTERFACE Figure 10 Message Device with MAC address 88 B6 27 01 00 05 registered successfully Return to device web interface and press Activate button energenie User qq Log out Device2 Ga Last seen online 05 May 2011 13 47 57 IP 80 252 18 146 88 B6 27 01 00 05Device web interface gt
16. d EGM PWM LANs please do the following Install Power Manager software on a PC connected to your local network socket icon will then appear in your system tray Choose device from the right upper corner see Figure 12 below device name connection My PMS LAN LAN Device65 USB Figure 12 27 All brands and logos are registered trademarks of their respective owners energe nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE asm In the Add LAN device window see figure 13 below please enter correct IP address port number 5000 by default and password 1 by default as configured on the Device settings page see section 4 6 above of the web server To disconnect from the device uncheck the option Enable set this option again to regain the access Click OK button to return to the LAN devices window Figure 13 Edit device r Device Name Device 2 Device IP 192 168 2 20 Port Password Measurements reading period sec Enabled Clear database 28 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w e To edit the LAN device select it and click the Device settings button or just double click on the LAN device e To remove the LAN device select it and click the Del button in the keyboard If the status of EGM PWM LAN shows the device is not Connected it could be due to the following r
17. d for about 3 seconds The above mentioned procedure forces EGM PWM LAN to reset itself to the default settings see below e 192 168 0 254 Subnet mask 255 255 255 0 7 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w e Gateway 192 168 0 1 e DNS 0 0 0 0 e DHCP enabled e filtering disabled e Power Manager client port 5000 EGM PWM LAN then searches for an IP address from your eventual DHCP server If no DHCP server is found within 1 minute EGM PWM LAN will then automatically revert to the default settings see above with IP 192 168 0 254 8 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE wn 3 2 Power Manager installation It is now time to identify which IP address has been obtained by EGM PWM LAN We need to carry out the following e Insert the Power Manager CD into PC CD ROM drive This PC can be connected either to the same LAN where the device is if you chose option A section 3 1 or directly to the device with the crossover RJ 45 cable if you chose option B section 3 1 f for any reason the automatic setup does not work then open CD ROM drive in the My Computer window and launch SETUP EXE from the CD e Follow instructions of the installation software NOTE Antivirus or firewall software may block connection to
18. e ni ne commencent pas une nouvelle p riode de garantie Le fabricant se r serve le droit d annuler toute demande de garantie pour les dommages ou d fauts dus une mauvaise utilisation abus ou les effets externes chute choc p n tration de l eau la poussi re etc Les pi ces d usure par exemple les piles rechargeables sont exclus de la garantie D s r ception de la marchandise sous garantie le SAV de Gembird Europe BV se r serve le droit de choisir entre le remplacement des produits d fectueux ou de d livrer un avoir Le montant d avoir sera toujours calcul e sur la base de la valeur actuelle du march des produits d fectueux Gembird Europe B V Gembird Europe B V Wittevrouwen 56 1358CD Almere The Netherlands www gembird nl support ort gmb nl Tel 0900 4362473 0 15 p m binnen Nederland Wittevrouwen 56 1358CD Almere The Netherlands www gembird nl support ort gmb nl 33 0 251 404849 Prix d appel depuis telephone fixe Pays Bas 0 15 euro min Prix d appel depuis telephone mobile autre pays selon operateur Exclusief mobiele telefoonkosten 47 All brands and logos are registered trademarks of their respective owners ene rge nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE ass wem 1
19. easons e Incorrect IP Port Password specified in the Add LAN device window e PC is not connected to the local network e You are trying to access EGM PWM LAN from the PC which is not allowed to do so Change PC IP address or change P filter list in EGM PWM LAN hardware settings see section 4 5 above e EGM PWM LAN is not connected to local network To check if EGM PWM LAN is on your local network you can do so called ping test e Goto Start gt Run e Type cmd e Type ping lt EGM PWM LAN IP Address specified in utility in the window which would appear Suppose EGM PWM LAN with IP address 192 168 2 189 is connected to the local network Then the cmd window will look as shown on the Figure 14 below 29 All brands and logos are registered trademarks of their respective owners energe EGM PWM LAN ENERGY METER WITH LAN INTERFACE sS Figure 14 Microsoft Windows Version 6 0 60021 Copyright lt c 2886 Microsoft Corporation All rights reserved C Users Administrator gt ping 192 168 2 189 Pinging 192 168 2 189 with 32 tes of data Reply from 192 168 2 189 byt 32 time ims TTL 128 Reply from 192 168 2 189 by 32 time lt ims TTL 128 Reply from 192 168 2 189 by 32 time lt ims TTL 128 Reply from 192 168 2 189 bytes 32 time lt ims TTL 128 Ping stat 5 for 192 168 2 189 Packe Sent 4 Received 4 Lost x loss Approximate round trip times in milli seconds Minimum ms Maximum ims Average C Users Admini
20. ed trademarks of their respective owners
21. elected on the chart and the start and finish values of the interval will be shown in the corresponding fields inside Statistics for the period box The calculated average value will be shown in the Mean value field Note you can also adjust the Start and Finish fields manually 38 All brands and logos are registered trademarks of their respective owners energe nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE w Tip You can calculate the total energy consumption within a certain period pushing the Calculate button see Figure 19 below Figure 19 x energenie POWER MANAGER va EGM PWM LAN Real Power Es 18 06 30 18 07 00 18 07 30 18 08 00 78 09 00 18 09 30 18 10 00 D Statistics for the period Graph details level Displayed value Time under the cursor Jui 17 2012 Start 17 07 2012 18 10 21 Mean value Real Power 09 Less More Automatically track new 108 End 17 07 2012 181021 2 Consumed s ei Num of points 100 Di d ti terval isplayed time in 0 days 00 hrs 03 mins Export to Excel 39 All brands and logos are registered trademarks of their respective owners energe nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE aes EN A The zooming tool allows changing the time scale of the chart Push the zooming tool button and then click with the left mouse button to adjust the scale to the desired level a When you select the home tool the c
22. ftware is started the main power manager window will appear which shows a list of all connected devices see Figure 12 above Push the Device settings button bottom right here to set the device specific options see Figure 13 above In the settings screen you are able to change the name of your device in the Name field and the data downloading frequency in the Measurement reading period field from 2 to 10 seconds To delete all previous recorded data just push the Clear database button Note Device IP Port and Enabled fields will be grey these functions are only available on the LAN version of the EGM PWM LAN 31 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE Sy To open the Power Meter window select your EGM PWM LAN device from the list see Figure 12 above and then click the Power meter button see the chapter 8 below 8 Power Meter The Power Meter window can be opened in either a minimized or maximized mode The minimized Power Meter window is shown in Figure 15 below This window is useful for monitoring selected measured values displays single measured value e g money spent Note Click with the right mouse button over this field to choose a different measured value to display Two warning indicators These indicators by default would show you when the voltage is beyond its limits too high or too low
23. hart displays every record from the whole period where the selected parameter has any records in the database e The Excel tool exports the average values of the selected period into an Excel file for further analysis or archiving see Figure 20 below Figure 20 1 TimeValuel Time Value TimeValue3 TimeValue4 2 21 06 2012 11 11 33 21 06 201211 12 00 61 49197 21 06 2012 11 12 00 21 06 2012 11 12 10 61 44834 W 21 06 2012 11 12 10 21 06 2012 11 12 30 61 41078 W 5 21 06 2012 11 12 30 21 06 2012 11 12 50 61 39684 40 All brands and logos are registered trademarks of their respective owners energe nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE w 10 Advanced features The Power Manager software also allows you to define a number of user defined events Possible events are Lighting up the indicators in the Power Meter window see Chapter 8 above or run a user specified application To set the parameters for such events see Figure 21 below just push the Events button in the Power Manager window see Figure 12 above Figure 21 POWER MANAGER energenie Name Action Voltage too high Vrms 230 000 Light up indic Voltage too low Vue SIT 210 000 To define your event first choose the parameter of your interest from the Value list box If you wish the event to be triggered when the value of 41 All brands and logos are registered trademarks of their respective owners
24. hen Deactivate button to stop communication of the device with EnerGenie com server If you eventually decide to change registration of your EGM PWM LAN and assign it to another account it will be possible via EnerGenie com website see section 5 below See section 5 below for further details on managing your EGM PWM LAN via EnerGenie com website Below the page you can see the current time of the web server and eventual information about the last successful timer synchronization Automatic timer synchronization is used if Use NTP for timer correction option is enabled see section 4 4 below 16 All brands and logos are registered trademarks of their respective owners energenie EGM PWM LAN ENERGY METER WITH LAN INTERFACE 4 3 LAN settings page Figure 7 Server 1 LAN settings Obtain IP address m automatically energenie usen IP address Subnet mask 2 Gateway EnerGenie DNS server Device Settings IP filter LAN Settings IP 1 0 000 IP 2 0 0 0 0 Log Out IP 3 0 0 0 0 MAC address Power Manager client port S000 On the LAN settings page see Figure 7 above you can set up DHCP IP address Subnet mask Gateway DNS server and IP filter up to 3 IP addresses can then be enabled for remote access The new settings will be applied immediately after you press the Apply button 17 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY MET
25. inell erstellte Kaufquittung zu belegen Bitte bewahren Sie Ihren Kaufbeleg daher f r die Dauer der Garantie auf da er Voraussetzung f r eine eventuelle Reklamation ist Innerhalb der Garantiezeit werden alle M ngel wahlweise durch den Hersteller entweder durch Instandsetzung Austausch mangelhafter Teile oder im Austausch behoben Die Ausf hrung der Garantieleistung bewirkt weder eine Verl ngerung noch einen Neubeginn der Garantiezeit Eine Garantieleistung entf llt f r Sch den oder M ngel die durch unsachgem e Handhabung oder durch u ere Einwirkung Sturz Schlag Wasser Staub Verschmutzung oder Bruch herbeigef hrt wurden Verschlei teile z B Akkus sind von der Garantie ausgenommen Gembird Europe B V Wittevrouwen 56 1358CD Almere The Netherlands www gembird nl support ort gmb nl Tel 31 36 5211588 GEMBIRD Deutschland GmbH Coesterweg 45 59494 Soest Deutschland www gembird de support support gembird de Tel 49 180 5 436247 0 14 pro Minute aus dem deutschen Festnetz Mobilfunkpreise k nnen abweichen 46 All brands and logos are registered trademarks of their respective owners energe Nie ENERGY METER WITH LAN INTERFACE w GARANTIE VOORWAARDEN CONDITIONS DE GARANTIE Garantie est de 24 mois a partir de la date d achat de De garantietermijn bedraagt 24 maanden en gaat in op de aankoopdatum van het product door de eindgebruiker Op de aankoopbon m
26. lt password is 7 It is recommended to change the password on the Device settings page see section 4 3 below after the first login 12 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w After a successful login you will face the Energenie page see section 4 2 below NOTE There is a possibility that you might then need to open the LAN settings page see section 4 3 below to complete the IP configuration 4 2 EnerGenie page With the help of EnerGenie page see Figure 6 below you will be able to see the current power consumption of the load connected Irms Vrms and Energy The EnerGenie page also allows you to setup access of your EGM PWM LAN from anywhere via Internet even if it does not have an external IP address To setup this free service you should follow two simple steps e Register the device To restrict access to the device via the Internet to the rightful owner only the device should be registered e g assigned to your account To register the device simply push the button Register on this page see Figure 6 below You will then be redirected to Login page of EnerGenie com If you already own an account at EnerGenie com then just enter your login and password on this page and you are done Otherwise use the Registration 13 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN
27. n NTP server poolntporg i Reset accumulated See Day Night mode M Day starts at 6 v Night starts at 23 v Page refresh 5 delay 10 x ply To be able to setup the schedule of EGM PWM LAN you have to first setup its internal clock correctly Enter the current local time and date 19 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w Alternatively if the option Use NTP for timer correction is enabled by default then the time will be taken from NTP server The device will try to connect with the server every 18 hours The first synchronization would take place in 15 seconds after you press the Apply button NTP server field should have a valid name of NTP server by default pool ntp org If for any reason the NTP time correction doesn t work you can choose the best NTP server for your country via the website www pool ntp org NOTE for NTP time correction to work properly the device should have access to the Internet and have a proper DNS server setting see section 4 3 above Server name can be convenient to identify the web server if you have more than one EGM PWM LAN It is Server 1 by default The password is necessary to access EGM PWM LAN both from your web browser and the Power Manager software see section 6 below This password is case sensitive and can be up to 32 characters long Alphanumeric charac
28. oeten de aankoopdatum en productomschrijving duidelijk vermeld staan Gelieve de aankoopbon de gehele garantieperiode te bewaren deze is ten alle tijden benodigd voor alle garantie aanspraken Tijdens de garantieperiode zullen alle gebreken verholpen of vervangen worden door de fabrikant d m v reparatie omruiling van het defecte onderdeel of het gehele apparaat Aanspraken tijdens de garantieperiode leiden niet tot verlenging hiervan Garantieaanspraak vervalt bij schade of gebreken die ontstaan zijn door oneigenlijk gebruik misbruik of invloeden van buitenaf vallen stoten water stof vuil of breken Slijtagegevoelige onderdelen b v batterijen zijn uitgesloten van garantie Bij ontvangst van de RMA goederen behoudt Gembird zich het recht om te kiezen tussen vervanging van de defecte waren of het uitgeven van een kreditnota Het bedrag van de kreditnota zal altijd gecalculeerd zijn op basis van de huidige marktprijs voor het defecte produkt l utilisateur final Le talon de garantie doit num rer clairement la date d achat et le type d appareil Conservez le re u d achat pendant toute la dur e de la garantie car elle est n cessaire pour toute r clamation Au cours de la p riode de garantie tous les d fauts doivent tre remplac aux frais du fabricant soit par la r paration ou la remplacement de la pi ce d fectueuse ou l ensemble du produit Les travaux effectu s sous garantie ne prolongent pas la p riode de garanti
29. ower measuring real energy consumed during a time period kWh e Measurements range up to 250 V AC 10 A RMS 2500 W 22 MW a year e Measurements accuracy 2 within 50 W 2500 W power range e Working conditions 10 to 40 C below 90 humidity e Resistance to short circuits 1 5 kV e Dimensions 135 mm x 92 mm x 78 mm e Net weight 0 35 kg All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE Sy 1 3 System requirements e LAN socket e Internet connection is required for uploading the information to EnerGenie com server 1 4 Package contents e EGM PWM LAN e Software CD e User manual e LAN crossover patch cord LAN patch cord All brands and logos are registered trademarks of their respective owners energe nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE w 2 Indicators and controls of the EGM PWM LAN Figure 1 Socket 1 energenie Day Night mode indicator POWER METER LAN Load indicator Reset button LAN activity indicators 5 LAN socket All brands and logos are registered trademarks of their respective owners energe Nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE w 3 Installation of EGM PWM LAN To use EGM PWM LAN please follow next steps e Connect EGM PWM LAN to the wall socket first and then to the LAN socket or your computer LAN card with the provided patch cord or vice versa
30. sed electrical and electronic devices please contact your city council or an authorized company for the disposal of electrical and electronic equipment Entsorgungshinweise um Werfen Sie dieses Ger t nicht in den Hausm ll Entsorgung kann sowohl der Umwelt als auch der menschlichen Gesundheit schaden Informationen zu Sammelstellen f r Altger te erhalten Sie bei Stadtverwaltung oder einer autorisierten Stelle f r die Entsorgung von Elektro und Elektronikgeraten Richtlijnen m b t afvalverwerking ii Batterijen en accu s dienen als klein chemisch afval afgeleverd te worden bij toegewezen afvalverzamelpunten zie www afvalgids nl U dient ervoor te zorgen dat de batterijen accu s leeg zijn en dus geen stroom meer kunnen leveren Let op de batterijen accu s dienen onbeschadigd ingeleverd te worden Gooi dit product niet weg in uw vuilnisbak Dit kan zowel het milieu als de gezondheid schade toebrengen Informatie over het inleveren van dit product kunt u inwinnen bij uw gemeentelijke vuilnisdienst of andere geautoriseerde instelling in uw buurt Traitement des d chets Ne jetez pas cet appareil dans les d chets domestiques Un traitement inappropri peut tre dommageable l environnement et a la sant humain Vous trouvez des informations sur les centres de rassemblement des appareils vieux chez l administration municipale ou
31. strator gt e EGM PWM LAN is connected to local network ping test is ok but not responding Reset EGM PWM LAN by pressing the Reset button A on the side control panel see Figure 2 above or switch it off and then on again see Figure 1 above NOTE The Reset button A see Figure 2 above can sometimes help if EGM PWM LAN can t be accessed or works abnormally The device will then be restarted All the IP settings and device settings will remain the same as before but the server time will be reset and all schedules will become outdated 30 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w 7 Power Manager Your EGM PWM LAN has an offline and an online working mode It is offline whenever it is not connected to a PC or when the PC is turned off The device will come online automatically when it is connected to a PC with the Power Manager software running In this mode the software keeps downloading the power readings from the EGM PWM LAN into a database In the offline mode the EGM PWM LAN will only save Energy consumption data kWh which will be logged into the database when the device comes online again The measured data can be viewed and analysed with the Power Manager software The software shows different energy characteristics changing over time including the money spent and the power consumption kWh When the so
32. ters and spaces are allowed to be entered Only the first eight characters of the password are used to access the device with the Power Manager software You will need to enter this password in the Add LAN device window see section 7 below The Power Manager software accesses EGM PWM LAN via a certain client port by default 5000 You can change this port to any other except port 80 which is always occupied by the web server Don t forget to push the Apply button to save your settings 20 All brands and logos are registered trademarks of their respective owners energe NIE ENERGY METER WITH LAN INTERFACE w 4 5 Web server logout Having finished working with EGM PWM LAN choose Log Out in the main menu If you don t do this you will be logged automatically after 10 minutes of inactivity While you are logged to the web server it can t be accessed from any other computer If another user tries to access the web server which is running an active session the error message will be shown on the login page Somebody with another IP has already logged in Try again later In the meantime the Power Manager software see section 6 can still access the EGM PWM LAN 21 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE y 5 EnerGenie com device interface With your free personal account at EnerGenie com website you will be able to ac
33. try to use Reset wrong with its IP address button to let the device renew its IP address see section 3 2 above Ok but not responding 43 All brands and logos are registered trademarks of their respective owners ene rge nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE ases EC Declaration of Conformity We hereby certify that the following product complies with all the relevant Safety Requirements of 4 EMVG and of the Directives 2006 95 EC 93 68 EEC and 2004 108 EC Applicant Gembird Europe BV Wittevrouwen 56 1358CD Almere The Netherlands Equipment Computer parts Model Nos EGM PWM LAN Product description EGM PWM LAN Energy Meter European standards EN55022 2006 EN55024 1998 A1 2001 A2 2003 EN61000 3 2 2006 EN61000 3 3 2008 EN60335 2002 A13 2008 EN55014 2006 EN55014 2 1997 A2 2008 The following manufacturer WITHIN Europe is responsible for this declaration Gembird Europe BV Wittevrouwen 56 1358CD Almere The Netherlands Tel 31 0 36 5211588 Fax 31 0 36 5347835 Director 2 The Netherlands Dec 6 2010 Place and Date Authorized signature 44 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE Sy Waste disposal Do not deposit this equipment with the household waste Improper disposal can harm both the environment and human health For Information about waste collection facilities for u
34. ve owners energenie EGM PWM LAN ENERGY METER WITH LAN INTERFACE Figure 17 o er __ Eri o Choose the rate per kWh and currency If you have different rates for peak hours and off peak hours just check the box Use Day Night modes You will then be able to enter the dual rates and the start finish times for these modes 35 All brands and logos are registered trademarks of their respective owners energe NIE EGM PWM LAN ENERGY METER WITH LAN INTERFACE w 9 Using the charts In the online mode the values of P R Fq Irms Vrms and Cost are continuously logged into the database These readings can be used to build time charts To display the charts just click on the desired value in the Main Power Meter window see Figure 16 above or push the Chart button in the Power Manager window see Figure 12 above This will open the Chart window as displayed in Figure 18 below 36 All brands and logos are registered trademarks of their respective owners energe nie EGM PWM LAN ENERGY METER WITH LAN INTERFACE w Figure 18 energenie POWER MANAGER 17 July 2012 EGM PWM LAN Cost 17 dy 2012 18 07 00 18 07 30 18 08 00 Graph details level EE Statistics for the period aph det level Displayed value Jul 17 2012 Start 17 07 2012 18 06 50 Mean value Cost Less p Automatically track new 17 07 2012 v 18 09 48 measurements a Num of points Displayed time
Download Pdf Manuals
Related Search