JLab JM-TILT-60 flat panel wall mount
Contents
1. Maintenance Once you have mounted the bracket and the flat screen check that they are sufficiently secure and safe to use You should check whether screws are fixed well every two months If you have any doubts regarding the installation please consult our retailer or service department for more details __ LE gt MOUNTS Designed by JLab in The United States Assembled in China 1 year limited warranty with world class customer support Please contact customer support with any questions or comments at www jlabaudio com support CLE MOLURA VT TS INSTALLATION INSTRUCTIONS Pitching angle 10 15 DODDODO D ooooooo0o000000 JLMS LLC suggests you contact a professional to properly install the JLab Mount This JLab Mount must be installed using the supplied hardware with all required lag bolts screwed into the center of the wall studs If you are mounting into concrete or mortar all included anchors and screws must be used By continuing with the installation you agree that JLUMS LLC and its affiliates cannot be held liable for damage to equipment including TV s Walls Furniture and Fixtures Additionally JLMS LLC is not responsible for incorrect installation and JLMS LLC and its affiliates cannot be held liable for any injury or death due to improper installation If you question your ability to properly install the JLab Mount please contact a professional Tilting TV Wall Mount with built in l2. 0 x4 M8x15 x4 M8x30 x4 M E M F M G M H e Always use an assistant or mechanical lifting equipment to safely lift and position equipment i i 2 e Tighten screws firmly but do not over tighten Over tightening can damage the screws washer 0 at x4 ak am greatly reducing their holding power Package W e This product intended for indoor use only Use of this product outdoors could lead to product failure and personal injury P ST6 3x55 x6 concrete anchor x6 6 5x 24 washer x6 W A W B W C Tools required Phillips Head Screw driver 200mm length exclude the handle M6 Socket and Wrench Electric drill and 10mm masonry bit for concrete wall installation Marking Pen Hammer 14 2 KEJ WOOD STUD WALL MOUNTING A WARNING e Make sure that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components e Tighten wood screws firmly but do not over tighten Over tightening can damage the screws greatly reducing their holding power e Make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into studs Installers are responsible to provide hardware for other types of mounting situations e Wall plate can be mounted to two studs Use a stud finder t
3. each of these holes Attach the wall plate to the wall using six screws W A and six M6 washers W C as shown in fig 1 3 PJ Installing Adapter Brackets e To prevent scratching the television screen set a cloth on a flat level surface that will support the full weight of the screen e Place screen face side down Place adapter brackets on the back of screen align to holes as shown in fig 2 1 e Attach the adapter brackets to the back of the screen using the appropriate combination of screws washers spacers as shown in fig 2 2 fig 2 3 and fig 2 4 NOTE For flat back screens proceed to step 2 1 For bump out or recessed back screen skip to step 2 2 gt 4 For Flat Back Screen Begin with the shortest length screw hand thread through washer and adapter bracket into screen as shown below e Screw must make at least three full turns into mounting hole and fit snugly into place Do not over tighten e If screw cannot make three full turns into screen select a longer length screw from the baffled fastener pack Repeat for remaining mounting holes level brackets and tighten screws NOTE Spacer may not be used depending upon the type of screen For Bump out or Recessed Back Screen e Begin with longer length screw hand thread through washer adapter bracket and spacer into screen as shown below e Screw mu
4. evel Fits 110lbs 32 55 TVs UPC 812887014007 NOTE Read entire instruction sheet before you start installation and assembly Component Checklist IMPORTANT Ensure you have received all parts against the component checklist prior to installing If any parts are missing or faulty please call your distributor for a replacement A WARNING e Do not begin the installation of this product before you have read and understood the instructions and warnings contained in this installation sheet If you have any question regarding any of the instructions or warnings Please contact your local distributor e Please refer to the installation guide recommendation for required distance from wall P 7 wall plate x1 to avoid risk of property damage Pare left adapter right adapte bracket x1 bracket x1 B C This product should only be installed by someone of good mechanical aptitude with basic building experiences and a full understanding of this manual Package M e Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components M4x10 x4 M4x20 x4 M5x10 x4 M5x20 x4 M A M B M C M D e Never exceed the maximum load capacity e If mounting to wood wall studs make sure that mounting screws are anchored into _ on Ly the center of the studs Use of an edge to edge stud finder is highly recommended M6x10 x4 M6x2
5. o locate the edges of the studs Use of an edge to edge stud finder is highly recommended Based on their edges draw a vertical line down each stud s center e Place wall plate on wall as a template And mark the center of the four mounting holes Make sure that the mounting holes are on the stud centerline Drill four 1 8 3mm dia Holes 1 2 30mm deep secure it using four screws W A and four M6 washers W C as shown in fig 1 1 Ed SOLID BRICK AND CONCRETE BLOCK MOUNTING A WARNING e When installing wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity e Installer must verify that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components 34 e Use the wall plate as a template to mark six hole locations on the wall Four in the top row slots and two more in the bottom row as shown in fig 1 2 e Pre drill these holes with a 10mm masonry bit to at least 60mm in depth Insert a concrete anchor W B into
6. st make at least three full turns into mounting hole and fit snugly into place Do not over tighten e If screw cannot make three full turns into screen select a longer length screw from the baffled fastener pack Repeat for remaining mounting holes level brackets and tighten screws 54 E Hang the brackets mounted TV onto the wall plate Warning A minimum of two qualified people are required for this operation e Loosen the safety screw on the display brackets e Hook the TV mounted display brackets over the top of the wall plate as shown in fig 3 1 e Tighten the safety screws on the display brackets with a proper screw driver as shown in fig 3 1 IMPORTANT MAKE SURE THE TV IS CORRECTLY HOOKED AND THE SAFETY LOCKING SCREWS ARE LOCKED SAFELY BEFORE RELEASING THE TV E Pitching angle adjustment Use the tilt adjusting knob to adjust your TV to the desired angle the pitching angle can be adjusted between 10 15 as shown in fig 4 1 Tilt adjusting knob gt 6
Download Pdf Manuals
Related Search