Foster 2510 060 cooker hood
Contents
1. 4 flash for 30 seconds to signal the need to clean filters ATTENTION The alarm can be reset by pressing for long speed key n 3 with engine switched off The keys perimetric edge remains always lighted To deactivate it press for long speed key n 1 with engine switched off ATTENTION To reactivate the lighting press for long speed key n 1 It is possible to automatically delay the stalling of the engine by pressing for long one of the speed keys The engine will run for others 10 minutes F12 17 MAINTENANCE Please switch off the electrical power or discon nect the appliance before carrying out any mainte nance operation 1 Cleaning of the stainless steel parts in order 2 to avoid scratches in the steel surfaces please don t use abrasive powders or brushes Use li quid detergents specifically made for stainless steel items Filter Cleaning Remove the filter from the container and wash it in the dishwasher or with soapy water without rubbing it with a cloth or a sponge Before replacing the filter carefully dry it wi thout deforming it ATTENTION The expelled air must not be convoyed in ducts which are shared by other appliances powered with energy different from the electrical one Should the use of the hood be contempora neous to other appliances powered by energy different from the electrical one an adequate ventilation on the room is to be foreseen Th2. Allow the tube to slight within the stack towards the upper bracket and lock it in place with the two screws T inserted inside the bracket use a flat tipped screw driver ATTENTION Prior to operation 7d Connect the exhauster with a 120 mm int exhaust pipe Use the supplied 150 to 120 mm plastic re duction Connect the power flex to the electricity main F12 16 ELECTRICAL CONNECTIONS before carrying out any electrical connection make sure that the voltage corresponds to the one men tioned on the label located on the inside of the ap pliance It is advisable to entrust the installation of the electrical connection to a qualified technician Appliance provided without plug please con nect a plug or an omni polar switch in compliance tothe existing local regulations and with an ope ning connection distance not inferior to 3 mm The earth wire must not be interrupted by the switch Foster decline any responsibility for any in conveniences deriving from the non obser vance of the aforesaid instructions of the use of materials which are not in compliance with the existing regulations CONTROL PANEL The control panel is electronic and is positioned in the lower end part of the hood FUNCTION OF BUTTONS 3 SWITCHED OFF 1 TURN ON 1st SPEED AND MOTOR TURN OFF 2 TURN ON 2nd SPEED 3 TURN ON 3rd SPEED 4 TURN ON 4th SPEED REMARKS After 30 hours use of the hood indicators of keys 1 2 3
3. spazzolato Foster inox spazzolato Foster Air outlet diameter 120 150 mm 120 150 mm Voltage 220 240 V 220 240 V Frequency 50 Hz 50 Hz Max absorbed Power 356W 359W 18 F12 Foster z via M S Ottone 18 20 Brescello RE ASSISTENZA TECNICA Tel 0522 684450 FAX 686019 MAIL service fosterspa com MAGAZZINO RICAMBI Tel FAX 0522 684300 MAIL assistenza fosterspa com Grafica e Stampa SERIART www seriart com FI2 09 09
4. Foster 527 S4000 Cappa Parete Wall Mount Hood 90 2440 090 Cappa Parete Wall Mount Hood 120 2440 120 J A Cappe d arredo HOODS Forni Built in ovens na Lavelli Sinks gt Miscelatori Faucets ATI Piani Cottura Cooker hobs C OUTLINE DIMENSIONS 50 11 INSTRUCTIONS FOR INSTALLATION MAINTENANCE AND USE OF THE S 4000 WALL MOUNT HOOD GENERAL INFORMATION before installing and using the hood read carefully all instructions contained in the present handbook We suggest that you always keep the handbook and the warranty certificate within easy reach USE the hood at issue is a SUCTION hood The odours and vapours coming from the motor shall be conve yed into and external exhaust duct The extractor hood can be converted into a Fil tering hood by purchasing the Carbon Filter pack carbon filter cod 9700400 F12 HOW TO INSTALL SERIE 4000 WALL MOUNT HOOD OPERATION 1 1a Mark a horizontal line on the wall on a level with the lower edge of the extractor hood at le ast 650 700 mm from the pan support 1b Mark a vertical line on the wall on the centre of the cooker hob 1c Mark the centres of the two holes on the wall 100 mm to 415 mm from the Horizontal line de scribed in point 1a 1d Mark on the wall the centres of the two holes 180 to 80 mm from the top of the chimney OPERATION 2 2a Using an 8 mm bit drill in the centres marked according to the instructions in
5. e use of an open flame under the hood or the preparation of food with an open flame is to be excluded as this could cause a fire Check that the oil doesn t overheat during the frying process in order to prevent it from catching fire The non compliance to filter cleaning recom mendations causes a risk of fire It is of course recommended to follow the said instructions F12 IMPORTANT The use of the hood in presence of other non electrical appliances such as but not limited to wood burning stoves gas stoves non electrical water heaters requires the presence of an exter nal exhaust which ensures a good ventilation of the room Verify the conditions of the exhaust chimney in case the hood is not used for a long period oftime Please also pay the maximum attention to the local standard regulations concerning exhaust scaven ging All recommendations on the subject should be scrupulously observed in order to avoid unpleasant inconveniences THE MANUFACTURER DECLINES ANY RE SPONSIBILITY CAUSED BY NON COMPLIAN CE TO THE HERE ABOVE MENTIONED RE COMMENDATIONS TECHNICAL FEATURES Type WALL MOUNT 90 WALL MOUNT 120 Code 2440 090 2440 120 Dimensions 898X490X50 mm 1198X490X50 mm Capacity 240 1000 m lh 240 1000 mh Cooking surface lighting n 6 LEDX 1W n 9 LED X1 W Anti grease filters 1 1 Perimetric suction elements 3 4 Working speed 4 4 Operation Aspirante Aspirante Finishing inox
6. points 1c and 1d the holes must be at least 60 mm in depth 12 Fi2 13 OPERATION 3 3a Insert 4 four FISCHER plugs into the holes made as described in point 2a 3b Fix the lower bracket in place with the screws not forgetting to insert the washers 3c Fix the upper bracket in place with the screws ATTENTION Use a level to make sure that the brackets have been correctly positioned OPERATION 4 4a Hang up the extractor hood by inserting the two screws X into the slots in the lower bracket 4b Using a screwdriver with a cross headed tip adjust the two screws so that the extractor hood is perfectly level F12 14 OPERATION 5 5a Mark the centre of hole Y inside the upper part and holes Z inside the lower part on the wall ATTENTION To access the holes Z open the perimetric suction elements pushing the centre of the frontal part 5b Remove the hood from the wall OPERATION 6 6a Using an 8 mm bit drill in the centres formed with the operations described in point 5a the holes must be at least 60 mm in depth F12 OPERATION 7 7a Insert 3 three FISCHER plugs into the holes made as described in point 6a 7b Hang up the extractor hood as described in point 4a ATTENTION Check the position of the extractor hood again with a level Regulate any misalignment with the screw as described in point 4a 7c Fix the extractor hood in place with the screws and washers 7d
Download Pdf Manuals
Related Search