Scosche NN1665B car kit
Contents
1. assemble the kit CAUTION DISCONNECT YOUR VEHICLE S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP PREVENT ELECTRICAL DAMAGE WE RECOMMEND THE USE OF A VOLT OHM METER OVER A TEST LIGHT TO CHECK WIRING A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE S COMPUTER AND OR DIAGNOSTIC SYSTEMS AVOID ALL FACTORY AIRBAG WIRING AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH NOTES e See your vehicle s instructions for any special tools your installation might require e Read all instructions accompanying your car stereo for proper wiring and mounting instructions LIABILITY DISCLAIMER This instruction booklet is based on carefully documented data and research of automobile dash disassembly wire harness codes and information pertaining to installation of this kit NN1665B in 2009 Up 370Z vehicles Scosche Industries Inc can not be held responsible for discrepancies inconsistencies that may occur due to the automobile manufacturing changes or options or damage that may occur in the automobile during the installation of components while using this booklet If you have any further questions call our toll free technical help line at 1 800 621 3695x3 2010 SCOSCHE INDUSTRIES INC SI 1 10 NN1665B 3000003 FACTORY WIRING CODES MOUNTING THE STEREO For Factory Wiring Codes go to Www scosche cars com SINGLE DIN MOUNT 1 Attach Factory A C controls to 6944 Panel using the 5 factor2. controls for re use during kit assembly 6 Remove 2 Phillips head screws from factory brackets securing A C module Retain screws and A C modules for re use during kit assembly Standard Radio 1 With Panel removal tool unclip panel surrounding shifter and move back 2 Extract 2 Phillips head screws securing side panel between shifter and A C controls and with panel removal tool unclip and remove Do this for both left and right side panels 3 Extract 2 Phillips head screws to the sides of the A C controls securing radio panel and with panel removal tool unclip unplug and remove 4 Extract 4 Phillips head screws securing radio bezel and A C controls unplug and remove 5 Extract 4 Phillips head screws securing radio unplug and remove 6 Extract 5 Phillips head screws securing the A C Controls to bezel Retain screws and A C controls for re use during kit assembly 7 Remove 2 Phillips head screws from factory brackets securing A C module Retain screws and A C modules for re use during kit assembly 6945 RIGHT BRACKET 6552 POCKET 6944 PANEL ASEMBLY
3. MOUNTING THE STEREO cont d DOUBLE DIN MOUNT 1 Attach factory A C controls to 6944 panel using the 5 factory Phillips head screws removed during disassembly see right 2 Attach 6945 and 6946 brackets to aftermarket double din stereo using screws supplied with aftermarket stereo 3 Attach A C module to 6945 and 6946 brackets using 2 Phillips head screws from factory brackets removed during disassembly 4 Reconnect and secure stereo A C module and brackets into dash using Phillips head screws removed during disassembly 5 Reconnect A C controls and place 6944 panel and factory A C control assembly into dash and secure using 4 during disassembly FACTORY SCREWS VARIOUS REAR SUPPORTS NOTE REAR SUPPORT AVAILABLE SEPARATELY REAR SUPPORT OF THE STEREO ADDS TO THE INSTALLATION S STRUCTURAL INTEGRITY 6946 LEFT BRACKET DBL DIN STEREO 6945 RIGHT BRACKET SCOsSsChHie NN1665B IN DASH STEREO INSTALLATION KIT FOR 2009 UP NISSAN 370Z NON NAVIGATION 6946 LEFT BRACKET 6945 RIGHT BRACKET 6944 PANEL 6552 POCKET INTRODUCTION PRELIMINARY This premium installation kit is for 2009 Up Nissan 370Z non navigation vehicles Included are all the parts you need to mount your car stereo or CD player into your vehicle s dash Refer to the individual instruction in this manual to remove your vehicle s factory radio and
4. y Phillips head screws CAR STEREO CONNECTORS NNO4B removed during disassembly see right SO NEO TD AC OR WIKING HARNESS T 2 Attach 6552 pocket to 6944 panel using screws supplied with kit See below NNO4B 3 p 3 Attach 6945 and 6946 brackets to aftermarket 2007 Up Nissan Connector Di stereo using screws supplied with aftermarket stereo 4 Attach AC module to 6945 and 6946 brackets using 2 Phillips head screws from factory brackets removed during disassembly NAA2B 2007 Up Nissan Antenna Adapter a 5 Reconnect and secure stereo A C module and brackets into dash using Phillips head screws removed during disassembly 6 Reconnect A C controls and place 6944 panel FACTORY STEREO REMOVAL 6552 pocket and factory A C control assembly into dash and secure using 4 during disassembly 2009 UP NISSAN 370Z non navigation FACTORY High End Radio SGREWS 1 With panel removal tool unclip panel surrounding shifter and move back 2 Extract 2 Phillips head screws securing side panel between shifter and A C controls and with panel removal tool unclip and remove Do this for both left and right side panels 3 Extract 2 Phillips head screws to the sides of the A C controls securing radio panel and with 6946 LEFT panel removal tool unclip unplug and remove BRACKET 4 Extract 6 Phillips head screws securing radio unplug and remove 5 Extract 5 Phillips Head screws securing A C controls to bezel Retain screws and A C
Download Pdf Manuals
Related Search