Philips AECS7000
Contents
1. e Press on the WeCall speaker to adjust volume e Adjust volume on the connected device such as your mobile phone tablet or PC Mac e Check whether you have selected the correct source e Check whether the WeCall speaker is switched on e Check the Bluetooth or USB connection to the WeCall speaker e Check whether you have started audio play or any call on the connected device Failed to set up Bluetooth connection Check whether the WeCall speaker is switched on see Turn on the WeCall speaker on page 7 e Check whether you have selected the Bluetooth source Make sure that the WeCall speaker and your Bluetooth enabled device are within the effective operation range that is approximately 10 meters 30 feet Remove any obstacle between the WeCall speaker and your Bluetooth enabled device Check the Bluetooth setting on your device to be connected with the WeCall speaker see the user manual of the specific device for details Hold CLEAR 6 at the bottom of the WecCall speaker for more than 3 seconds to reset and then try again If there is any issue with Bluetooth connection to a PC Mac upgrade the Bluetooth driver of your PC or the iOS version of your Mac After first time pairing with a Mac the WeCall speaker may be shown as disconnected It is a not a malfunction You just need to make VoIP calls or play music through the WeCall speaker directly to activate the Bluetooth connectio2. SSSR EES SSS EF gt lt SESS e During audio play you can use on the WeCall speaker to adjust volume e During audio play you can press X to mute the WeCall speaker EN 11 5 Product information Amplifier Rated Output Power 2W RMS Frequency Response SOmIZ lok mz 3dB Signal to Noise Ratio gt 5dB Bluetooth Bluetooth version V2 1 EDR Frequency band O e OAS Band Range 10m free space Speakers Speaker Impedance 4ohm Speaker Driver Eee Sensitivity gt 84dB 1WV 1m General Information DC Power Input Input 5 VDC 1 A Battery Model No SDL 553055 1000mAh Rating voltage and capacity 3 7VDC 1000mAh Dimensions Main Unit w x 110 x 28 x 110 mm h x d Weight With Packing OB ake Main Unit 0 17 kg 6 Troubleshooting Warning e Never remove the casing of this device To keep the warranty valid never try to repair the system yourself If you encounter problems when using this device check the following points before requesting service If the problem remains unsolved go to the Philips Web page www philips com support When you contact Philips make sure that the device Is nearby and the model number and serial number are available No power Check whether the WeCall speaker is switched on see Turn on the WeCall speaker on page 7 e Recharge the WeCall speaker see Charge the WeCall speaker on page 7 No sound
3. regulations regarding the disposal of packaging materials exhausted batteries and old equipment Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by WOOX Innovations Is under license CYS Skype Is a trademark of Skype or its related companies Although this product has been tested and met our certification standards for audio and video quality it is not endorsed by Skype Skype Communications S a rl or any of their related companies Efa No emergency calls with Skype Skype is not a replacement for your ordinary telephone and can t be used for emergency calling Note e The type plate is located on the bottom of the device 2 Your WeCall speaker To fully benefit from the support that Philips offers register your product at www philips com welcome Introduction This Bluetooth conference speaker VWeCall speaker allows you to e connect to a Bluetooth enabled smartphone and make a mobile or VoIP call through the WeCall speaker directly e connect to a PC Mac through the supplied USB cable and make a VoIP call through the WeCall speaker directly e connect to a Bluetooth enabled iPhone and make a conference call through the WeCall speaker with the help of the WeCall App e enjoy music from a Bluetooth enabled mobile device or a PC Mac e enjoy music from a PC Mac connected through the supplied USB
4. the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation French Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence et la partie 15 des R gles FCC L exploitation est autoris e aux deux conditions survantes 1 l appareil ne doit pas produire de brouillage A 2 l utilisateur de l appareil dort accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement RF Exposure info This equipment complies with FCC s and IC s RF radiation exposure limits set forth for an uncontrolled environment The antenna s used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter Installers must ensure that 20cm separation distance will be maintained between the device excluding its handset and users French Cet appareil est conforme aux limites d exposition au rayonnement RF stipul es par la FCC et l IC pour une utilisation dans un environnement non contr l Les antennes utilis es pour cet metteur doivent tre install es et doivent fonctionner a au moins 20 cm de
5. 0 AM gt project sharing Friday 8 February 2013 i Regular review meeting aili with John Monday 12 February 2013 Town Meeting Group Design TOAN and CL Design Tuesday 13 February 2013 LLAN DAA DA LE Taum Manatina EN 5 Confirm the telephone number and code wt 3G 4 20 PM Enter the call details Cancel Add call Done rc a i Regular project review i photo i meeting with Paul I l t Phone 3028 9802 Code 96425379 Regular project review meeting Sender Paul Hardstuff D EnasT3 HK 852 80289802 China 86 4007815907 Participants code 96425379 6 Make a conference call ui_ one2free 2 21 PM 45 mw _ 852 30279902985643256 Calling 4 mute speaker add call FaceTime contacts Tip During a call you can use on the WeCall speaker to adjust volume During a call you can press X to mute the WeCall speaker so that the other party cannot hear you During a call you can press to end the call After a call you can press twice consecutively to redial the last number Use as a Bluetooth or PC speaker 1 2 Make sure that you have selected the correct source on the WeCall speaker In Bluetooth mode start audio play on the Bluetooth enabled device and then listen from the WeCall speaker T a ET In USB mode start audio play on the PC Mac and then listen from the WeCall speaker z aos SSS
6. Always there to help you Register your product and get support at www philips com welcome ON Question Contact Philips AECS7000 WecCall PHILIPS User manual PHILIPS Contents 1 Important Important Safety Instructions Notice Your WeCall speaker Introduction What s in the box Product overview Get started Charge the WeCall speaker Turn on the WeCall speaker Connect the WeCall speaker Use the WeCall speaker Use as a speaker phone Use together with the WeCall App for iPhone Use as a Bluetooth or PC speaker Product information Troubleshooting NN NON N N Ow Mm WM O O 12 13 EN 1 Important Important Safety Instructions The translation of this document is for reference only In the event of any inconsistency between the English version and the translated version the English version shall prevail e Follow all instructions e Heed all warnings e Do not use this device near water e Clean only with dry cloth e Do not block any ventilation openings Install in accordance with the manufacturer s instructions e Do not install near any heat sources such as radiators heat registers stoves or other devices including amplifiers that produce heat e Only use attachments accessories specified by the manufacturer e Refer all servicing to qualified service personnel Servicing is required when the device has been damaged in any way suc
7. ES 003 French Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Disposal of your old product Your product is designed and manufactured with high quality materials and components which can be recycled and reused Never dispose of your product with other household waste Please inform yourself about the local rules on the separate collection of electrical and electronic products and batteries The correct disposal of these products helps prevent potentially negative consequences on the environment and human health EN Your product contains batteries which cannot be disposed of with normal household waste Please inform yourself about the local rules on separate collection of batteries The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health Please visit www recycle philips com for additional information on a recycling center in your area Always bring your product to a professional to remove the built in battery Environmental information All unnecessary packaging has been omitted We have tried to make the packaging easy to separate into three materials cardboard box polystyrene foam buffer and polyethylene bags protective foam sheet Your system consists of materials which can be recycled and reused if disassembled by a specialized company Please observe the local
8. all such as a Skype IM call on your tablet or PC Mac 3 Use the WeCall speaker as a speaker phone during the call Eas e When there is an incoming mobile call you can press C A to answer the call e During a mobile call you can press to end the call e During a mobile call you can press X to mute the 4 built in microphones of the WeCall speaker so that the other party cannot hear you e During a mobile or VoIP call you can use on the WeCall speaker to adjust volume If the WeCall speaker has been connected to a PC Mac through the USB cable 1 Make sure that you have selected the USB source on the WeCall speaker 2 Make aVolP call such as a SkypeTM call on your PC Mac 3 Use the WeCall speaker as a speaker phone during the call Use together with the WeCall App for iPhone 1 Download Philips WeCall to your iPhone EN 9 10 Set up Bluetooth connection between the WeCall speaker and your iPhone see Option 1 Connect to a Bluetooth enabled device on page 7 Set events for conference calls in the calendar of your iPhone or Android phone Run Philips WeCall and import conference calls from your calendar atl 3G 4 20 PM Tw _ Choose an event to add to Calls Cancel Calendar Today Home monitor product 12 00 PM concept review 1 00 PM Design review 3 00 PM Regular team meeting Thursday 7 February 2013 UX team planning and 9 3
9. cable What s in the box Check and identify the following which are included with your WeCall speaker WeCall speaker e Carrying case e USB cable e Printed materials EN 5 Product overview O o LH Q 7 _ FAY 5 Q e Adjust volume during a call or music play ON OFF power switch e Power on or off the WeCall speaker CLEAR e Remove the existing pairing information Charge indicator e Turns red when the battery Is running low or when you charge the WeCall Speaker Micro USB socket e For connection with the supplied USB cable EN St USB 8 source switch e Switch between the USB or Bluetooth audio sources c a e Answer an incoming mobile call e End an ongoing mobile call Source indicator e Turns blue in Bluetooth mode e Turns green in USB mode ex e Mute the 4 built in microphones of the WecCall speaker during a call so that the other party cannot hear you 3 Get started Caution e Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation Always follow the instructions in this chapter in sequence Charge the WeCall speaker e Connect the WeCall speaker to a PC Mac through the supplied USB cable L gt The charge indicator turns red L gt When the WeCall speaker is fully charged the
10. charge indicator turns off EON SSCS SSS SSeS z e You can also charge the WeCall speaker through a USB power adapter not supplied Ea e When the battery is low the charge indicator flashes red It takes approximately 2 hours to fully charge the WeCall speaker The fully charged WeCall speaker supports approximately 8 hours of operation Turn on the WeCall speaker Slide the power switch to the ON position L gt n Bluetooth mode the status indicator turns blue L gt In USB mode the source indicator turns green e To turn off the WeCall speaker slide the power switch to the OFF position Connect the WeCall speaker Option 1 Connect to a Bluetooth enabled device You can pair the WeCall speaker with a Bluetooth enabled mobile device such as your mobile phone or tablet or PC Mac Then you can enjoy music from the WeCall speaker or use It as a speaker phone when you make mobile or VoIP calls Note e The effective operation range between the WeCall speaker and your Bluetooth enabled device is approximately 10 meters 30 feet 1 Slide the source switch at the bottom of the WeCall speaker to the position EN 7 2 Enable Bluetooth on your Bluetooth enabled device 3 Select Philips WeCall speaker on your Bluetooth enabled device and if necessary input OOOO as the paring password Ly The source i
11. distance des utilisateurs et ne doivent pas tre plac es pr s d autres antennes ou metteurs ou fonctionner avec ceux ci Les installateurs doivent s assurer qu une distance de 20 cm s pare l appareil a l exception du combin des utilisateurs FCC Section 15 105 statement NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help ICES 003 complies statement This Class B digital apparatus complies with Canadian IC
12. h as liquid has been spilled or objects have fallen into the device the device has been exposed to rain or moisture does not operate normally or has been dropped e Battery usage CAUTION e To prevent battery leakage which may result in bodily injury property damage or damage to the unit the batteries battery pack or batteries installed shall not be exposed to excessive heat such as sunshine fire or the like e Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate e CAUTION Danger of explosion if battery is Incorrectly replaced Replace only with the same or equivalent type e The device shall not be exposed to dripping or splashing e Do not place any sources of danger on the device e g liquid filled objects lighted candles UN Warning e Never remove the casing of this device e Never lubricate any part of this device e Never place this device on other electrical equipment Keep this device away from direct sunlight naked flames or heat About replacement of parts accessories Visit www philips com support to order replacement parts accessories Notice Any changes or modifications made to this device that are not expressly approved by WOOX Innovations may void the user s authority to operate the equipment FCC amp RSS compliance statement This device complies with Industry Canada licence exempt RSS standard s and Part 15 of
13. n EN 13 PHILIPS 2014 WOOX Innovations Limited All rights reserved This product was brought to the market by WOOX Innovations Limited or one of its affiliates further referred to in this document as WOOX Innovations and is the manufacturer of the product P amp F is the warrantor in relation to the product with which this booklet was packaged Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N V AECS7000_37_UM_V2 0
14. ndicator starts to flash blue L gt After successful pairing and connection the source indicator turns solid blue and the WeCall speaker beeps e To pair with a new Bluetooth enabled device you can e 1 Hold CLEAR at the bottom of the WeCall speaker for more than 3 seconds to remove the existing Bluetooth connection e 2 Disable the Bluetooth function on the currently connected device e The WeCall speaker can memorize up to 4 paired devices When you pair with another Bluetooth enabled device the first memorized device will be overridden Tip e For PC Mac to ensure stable performance the USB connection mode is recommended Option 2 Connect through USB The USB cable charges the WeCall speaker and can also be used to connect the WeCall speaker to a PC Mac to enjoy music or use it as a speaker phone when you make VoIP calls 1 Slide the source switch at the bottom of the WeCall speaker to the USB position 2 Connect the WeCall speaker to a PC Mac through the supplied USB cable L The source indicator turns green 4 Use the WeCall speaker Use as a speaker phone If the WeCall speaker has been connected to a Bluetooth enabled mobile phone or other devices such as a tablet or PC Mac 1 Make sure that you have selected the Bluetooth source on the WeCall speaker 2 Make a mobile or VoIP call on your mobile phone or a VoIP c
Download Pdf Manuals
Related Search