Intex 28645EG water pump
Contents
1. 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English SAND FILTER PUMP HOSE CONNECTION SETUP continued For NON INTEX pool Connect the hose 12 to the pool inlet outlet connection with a large hose clamp Tighten securely Remove the drain cap 3 before attaching the drain waste hose or pipe LARGE HOSE CLAMP For INTEX pool size 16 and below In acounter clockwise motion unscrew plunger valve union from the threaded strainer connector 26 Be careful not to lose the step rubber washer 23 Grasp the plunger valve assembly Make sure the step washer 23 is in place Connect adaptor B 28 to plunger valve union Remove wall plug and then insert the strainer 29 amp 31 into the lower position of protruding hose connection and the nozzle 29 amp 30 into the upper position of protruding hose connection Adaptor B 28 fits over the strainer connection 29 inserted into the connection Tighten securely 4 Remove the drain cap 3 before attaching the drain waste hose or pipe SAVE THESE INSTRUCTIONS Page 13 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 OPERATING INSTRUCTIONS A WARNING Risk of electric shock Connect this product only to a grounding type receptacle protected by a ground fault circuit interrupter GFCI or residual current device RCD Contact a qualified electrician if you cannot verify that2. INTEX INTEX ABOVE GROUND POOLS AGP s 0 GROUND POOLS INTEX ABOVE GROUND POOLS AGP s 0 s 457cmx84cm 15 x33 2587 9792 457cmx91cm 15 x36 2822 10681 457cmx1 Dm 5 x42 3284 12430 EASY SET POOL Bouno 4STemxi22em iSw4g 4440 316805 4 METAL 8 220 1648 501 19156 4 FRAME POOL S4gemxrzacm1exas 6 asn 4 2 2 52 _ 95 39 4 4 7azematazcm 2axse 12481 an 8 220 16 48 9061 19 56 sacma zn 4 4 Simds2maexs2 6981 20423 4 4 ULTRA FRAME 4 22 52 __ 10972 399 8 a TS2emkis2emQaxsz 12481 an e e 5 sssemerasemcreass ase 6 _ _ e POOL _ s66emx6t0emxtzzem t2x20 48 4909 16688 4 2 2 27 8 220918487 sasa 19187 4 2 2 EZE 305 1 0 132 10 20 52 sess 22085 4 4 2 366cmx732cmxt32cm 12x20x52 saos stss 6 4 4 75 132 1832 2 14964 5458 12 8 6 NOTE The 12 hours timer setting o has an additional 20 minutes over the actual setting MVE AAA MEM A TS Tum FAFA tAE SAVE THESE INS
3. The drain valves are loose Heavy use getting in and out of pool SOLUTION Super chlorinate with shock treatment Correct pH to your pool store s recommended level Vacuum pool bottom Maintain proper chlorine level Adjust pH level to the recommended level Run filter until water is clear Correct the pH level Check with your pool dealer for advice Adjust the chlorine level Repair with a patch kit Finger tighten all caps Use Intex pool vacuum to clean bottom of pool SURFACE Leaves insects etc Pool too close to trees Use Intex pool skimmer DEBRIS Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference interference that may cause undesired operation of the device Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee th
4. B on the pump by pressing the switch to position the sand filter pump is now filtering the water and will stop after the operating hours are completed The built in timer will now operate for the number of hours selected at the same time each day C Operating hours can be re adjusted if necessary Follow step A B To operate the sand filter pump manually without the TIMER mode A Turn on the pump by pressing the switch to position the sand filter pump is now filtering the water B To turn off the pump press the switch to O position TIMER DIAL HOURS TIMER IMPORTANT If you continue to experience difficulty please contact our Consumer Service Department for assistance See separate Authorized Service Centers sheet SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English INTEX POOLS OPERATING TIME TABLE WITHOUT INTEX SALTWATER SYSTEM This table shows the required operating time for average use of the sand filter pump with above ground pools If the system is attached to an Intex Saltwater System unit the filter pump running time should be longer than the required operating time of the Intex Saltwater System unit Water Capacity Calculated at x 90 for Frame Pool and 80 Pool Size for Easy Set amp Oval Pool Gals Liters SF80110 SF70110 SF60110 Sand filter pump operating time For one cycle Hours
5. 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English po IMPORTANT SAFETY RULES Read understand and follow all instructions carefully before installing and using this product Model SF80110 Model SF70110 Model SF60110 UNTEX IMPORTANT DO NOT RETURN PRODUCT TO STORE To purchase parts and accessories or to obtain non technical assistance visit www intexcorp com For technical assistance and missing parts call us toll free for U S and Canadian Residents 1 800 234 6839 Monday through Friday 8 30am to 5 00pm Pacific Time 195 PO R0 1406 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English TABLE OF CONTENTS Warnings Parts References Setup Instructions Product Specifications Operating Instructions Intex Pools Operating Time Table Non Intex Pools Operating Time Table Maintenance Long Term Storage Troubleshooting Guide Common Pool Problems General Aquatic Safety Limited Warranty SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English IMPORTANT SAFETY RULES Read Understand and Follow All Instructions Carefully Before Installing and Using this Product READ AND FOLLOW ALL INSTRUCTIONS A WARNING To reduce the risk of injury do not permit children to use this product Always supervise children and those with disabilities Children mu
6. 39744 _ dL 65 Optional When ordering parts be sure to quote the model number and part numbers lll SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English POOL OUTLET STRAINER amp PLUNGER VALVE SETUP optional The strainer grid prevents large objects from jamming and or damaging the filter pump If your pool has an inflatable top ring install the strainer nozzle and plunger valve before inflating the pool liner top ring The part numbers here onward refer to the parts depicted in the Parts List section of this manual To install do the following In a counter clockwise motion unscrew plunger valve union from the threaded strainer connector 26 see drawing 1 Be careful not to lose the step rubber washer 23 Place the plunger valve on the ground in a safe place In a counter clockwise motion unscrew the strainer nut 24 from the threaded connector 26 Leave the flat washer 25 on the connector 26 Install the strainer and plunger valve at the lower position of pool outlet marked From the inside of the pool liner insert the connector 26 into one of the pre cut holes with the washer remaining on the connector to be placed against the inside of the liner wall Before assembly lubricate the threads with a petroleum jelly With the flat side of the strainer nut 24 facing the outside wall of the liner in a clockwis
7. and reassembled to its original integrity A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage These product warnings instructions and safety rules provided with the product represent some common risks of water recreation devices and do not cover all instances of risk and danger Please use common sense and good judgement when enjoying any water activity SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 PARTS REFERENCE Before assembling your product please take a few minutes to check the contents and become familiar with all the parts E o Optional SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 SPARE PART NO SF80110 SF70110 SF60110 ame S S 6 mosen oO ES 9 REF NO DESCRIPTION PRESSURE GAUGE 6 WAY VALVE DRAIN OUTLET COVER CLAMP x lt 10 HosEWmHNUTS 11009 moo 1100 SANDFILTERINTERGONNECTING HOSE 1 11820 11988 11595 _ 14 UEAFTRAPNUT e nam 11479_ 15 jLEAFTRAPORING O 11824 11232 11282 1e BAT 11260 11260 i7 FLTER
8. drawing 32 In a counter clockwise motion unscrew the leaf trap cover 14 then remove the basket 16 and leaf trap o ring 15 from the pre filter housing see drawing 33 5 Empty and flush the basket using a garden hose may use a plastic brush to remove deposits from the basket Do not use metal brush 6 Clean and rinse the inside of the pre filter housing and the leaf trap O ring with a garden hose 7 Reinstall the leaf trap O ring basket and leaf trap cover to the pre filter housing 8 Close the sediment release valve 19 back SAVE THESE INSTRUCTIONS Page 19 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English POOL CARE amp CHEMICALS All pools require care to keep the water clear and hygienically clean With proper chemical control your filter will help attain this objective Consult your pool supply dealer for instructions regarding the proper use of chlorine algaecide and other chemical agents required for sparkling clear water Keep pool chemicals away from children Do not replenish chemicals in pool while pool is occupied Skin or eye irritations could occur Daily pH checking and chemical treatment of the water is very important and cannot be overemphasized Chlorine algaecide and maintenance of proper pH levels are required when filling the pool as well as during the season Consult your local swimming pool supply store for instructions The season s first f
9. inspect for any visible damage For missing or damaged parts contact the appropriate Intex Service Center listed in the separate Authorized service Centers sheet In a counter clockwise motion unscrew the leaf trap cover 14 from the pre filter housing Take out the basket 16 and filter housing nut 17 see drawing 10 Connect the pre filter housing to the motor water inlet Note Align the connector in the pre filter housing with the water inlet on the motor see drawing 11 Lam INI te IN zu 22 n ID C p Zi pni adi Q 104 SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 SETUP INSTRUCTIONS continued 4 Ina clockwise motion screw filter housing nut 17 onto the motor water inlet See drawings 12 1 amp 12 2 5 Replace the basket 16 and leaf trap cover 14 back to the pre filter housing See drawings 13 1 amp 13 2 Sand tank installation Place the tank support base on the selected location Place the tank on the tank support base See drawing 14 1 Connect the motor pre filtering assembly unit to the tank support base See drawing 14 2 NOTE Ensure the pre filter housing water inlet hose connection is facing towards the pool IMPORTANT Some countries especially in the European community require the product to be secured to the ground or to a base in a permanent upright position Check y
10. pump and run the pump for about one minute to level out the sand bed after backwashing the sand media Switch off the pump change the 6 way valve to FILTER position see drawing 23 Switch on the pump The system is now operating in the normal filtering mode Run the pump until the desired pool water clearance is obtained and no more than 12 hours per day Record the initial pressure gauge reading when the filter media is clean NOTE During initial setup of the system it may be necessary to backwash frequently due to unusual heavy dirt present in the water and sand After that as the filter removes dirt and impurities from the pool water the accumulated dirt in the sand media will cause the pressure to rise and the flow to diminish If there is no vacuuming device attached to the system and the pressure gauge reading is in the yellow zone it is time to backwash the sand media see BACKWASH under initial startup and operation section Vacuuming device i e Intex auto pool cleaner attached to the system may also cause the flow to diminish and the pressure to rise Remove any vacuuming device from the system and check if the pressure gauge reading has dropped from the yellow zone to the green zone Operating the system under TIMER mode or manually To operate the sand filter pump in FILTER mode under TIMER control A Setthe timer dial to the desired operating hours See operation time table see drawing 31
11. valve cover and ensure the o ring is in place Clean sand tank o ring with garden hose water Tighten the clamp with wrench supplied Contact Intex service center Tighten reinstall hose nut Ensure o ring L shape o ring is in place and not damaged Turn off the pump and restart 5 minutes later Re set the timer Contact Intex service center Clear any obstructions in the intake by unscrewing it from the 6 way valve Contact Intex service center Use only No 20 silica sand with particle size range 0 45 to 0 85 mm 0 018 to 0 033 inches and a Uniformity Coefficient less than 1 75 Change sand SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 COMMON POOL PROBLEMS PROBLEM DESCRIPTION ALGAE Greenish water Green or black spots on pool liner Pool liner is slippery and or has a bad odor COLORED WATER Water turns blue brown or black when first treated with chlorine FLOATING MATTER IN WATER Water is cloudy or milky CHRONIC LOW WATER LEVEL Level is lower than on previous day SEDIMENT ON POOL BOTTOM Dirt or sand on pool floor Chlorine and pH levels need adjustment Copper iron or maganese in water being oxidized by the added chlorine This is Common Hard water caused by a too high pH level Chlorine content is low Foreign matter in water Rip or hole in pool liner or hoses
12. HOUSNGNUT 3 iei 19261 L SHAPE O RING 3 na 142 i9 AIR RELEASE VALVE SEDIMENT RELEASE VALVE 2 10460 10460 10460 _ 20 VAvEORNG f 2 10264 i264 10264 21 PLUNGER VALVE HOSE OFING amp STEP WASHER NOLUDED 2 10747E 10747 10747 _ zx HostoRNG 10262 10262 25 srEPWASHER OO i745 10745 24 STRANERNUT i056 io256 10256 25 FLAT STRAINER RUBBER WASHER 2 10255 10255 10255 _ 26 THREADED STRAINER CONNECTOR 2 11235 10744 10744_ zr ADJUSTABLE POOL NLET NOZZLE 1 11074 11074 11074 25 ADAPTORB o o y o oe 10722 10722 29 STRAINER CONNECTOR 2 noo i070 11070 sw POOLINLETNOZ E Mori sr SmANERGRID O 3 Moz 1072 33 PUMP MOTOR amp CONTROL mer meea T1807EG 34 PRE FILTER ASSEMBLY i 118 35 LEAFTRAPCOVER OO o 3 i480 11480 36 VACUUMRELEASEVALVE 2 nar 4s 11497 S7 VACUUM RELEASE VALVE CAP NOT SHOWN 2 11576 11576 11576 _ 38 SAND FILTER PUMP MOTOR INLETO NING 2 11457 11457 11457 39 SANDFILTERPUMPTANK meos 11802 1180 40 SAND FILTER PUMPTANKBASE 3 11816 11800 11801 _ 417 THREADED STRAINER CONNECTOR 2
13. TRUCTIONS PELE Us 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English NON INTEX POOLS OPERATING TIME TABLE This table shows the required operating time for average use of the sand filter pump with above ground pools Water Capacity Sand filter pump operating time For one cycle Hours Gals Liters SF80110 SF70110 SF60110 NEN NEN NN RN me me 3 7 ow p E ome ws LLL ome xm 8 3 3 mw m9 oom omm LLL me 9m 3 9 s e LE LL e me cwm 2 3 s 099 cm o 5 ome LLL m e j e RR RR RN m m MM o or mee me EN INNEN NEN DE NN NN RR NN omm me e LL wee e me cm L omm c LL LL SAVE THESE INSTRUCTIONS Page 18 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English MOTOR PRE FILTER CLEANING AND MAINTENANCE Make sure the filter pump is switched off then disconnect the power cord from the electrical outlet Turn both plunger valve handles fully clockwise until they stop This closes the valve prevents the water from flowing out of the pool Release the pressure first by opening the sediment release valve 19 located on the lower side of the pre filter housing see
14. at interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 GENERAL AQUATIC SAFETY Water recreation is both fun and therapeutic However it involves inherent risks of injury and death To reduce your risk of injury read and follow all product package and package insert warnings and instructions Remember however that product warnings instructions and safety guidelines cover some common risks of water recreation but do not cover all risks and dangers For additional safeguards also familiarize yourself with the following general guidelines as well as guidelines provided by nationally recognized Safety Organizations Demand constant supervision A competent adult should be appointed as a lifeguard or water watcher especially when children are in and around the pool Learn to swim Take the
15. bolt and install the clamp around the tank and 6 way valve flanges then replace the clamp bolt and use a phillips screwdriver not included to tighten it see drawings 22 AM 3 Ur Vl SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English SAND FILTER PUMP HOSE CONNECTION SETUP A WARNING Position this product away from the pool so as to prevent children from climbing on it and accessing the pool The 6 way valve has three hose connection ports Connect one hose 12 end to the pre filter inlet and the other end of the hose to the lower plunger valve with the strainer Ensure the hose nuts are securely tightened Connect the second hose 12 between the 6 way valve water outlet and the upper plunger valve with the inlet nozzle Ensure the hose nuts are securely tighten The third hose connection port drain waste outlet on the 6 way valve shall be directed to a proper draining receptacle using a hose or pipe not provided Remove the drain cap before attaching the drain waste hose or pipe The sand filter pump is now ready to filter the pool WATER LEVEL 6 WAY VALVE PLUNGER WATER OUTLET L SHAPE 3 ADJUSTABLE O RING POOL INLET S NOZZLE b THREADED STRAINER CONNECTOR L SHAPE O RING OUTSIDE LINER WALL MOTOR MOTOR PRE WATER FILTER OUTLET ILLUSTRATION NOT TO SCALE SAVE THESE INSTRUCTIONS Page 12
16. d in This prevents the center pipe hub 7 from excessive shock see drawing 17 Place the sand shield 6 back and continue to pour the sand into the tank Sand shall be filled between the MAX and MIN marked gauge on the center pipe Evenly spread and level out the sand by hand see drawings 17 amp 18 5 Remove the sand shield 6 6 Wash away all sand around the top edge of the tank SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 SETUP INSTRUCTIONS continued A WARNING Improper tank valve and clamp assembly could cause the valve and clamp to blow off and cause serious injury property damage or death 6 way valve installation 1 Lower the 6 way valve over the tank slowly and ensure the bypass pipe protruding underneath the 6 way valve fits securely into the center pipe hub 7 top opening see drawing 19 IMPORTANT There are three hose connection ports on the 6 way valve ensure the outlet connection from filter to the pool on the valve is facing towards the pool and the inlet connection from motor to valve is aligned with the motor outlet see drawing 20 WATER OUTLET Place an L shape o ring 11 on the 6 way valve inlet connection and on the pump motor outlet In a clockwise motion connect the sand filter interconnecting hose 13 between the pump motor outlet and the 6 way valve inlet connection see drawing 21 Remove the clamp
17. d remove the strainers plunger valves from the pool wall In a counter clockwise motion unscrew the drain valve cap 9 from the drain valve to thoroughly drain the tank The drain valve is located at the bottom of the filter tank Disassemble the pump motor from the tank base Leave sand filter pump pieces and hoses outside to thoroughly air dry Coat the following o rings and washers with petroleum jelly for long term storage L shape o rings 11 amp 18 Pump hose O rings 22 Strainer valve assembly step washers 23 Flat strainer rubber washers 25 Depress the 6 way valve handle and rotate so as to set the pointer on the valve top N position This allows the water to drain from the valve Leave the 6 way valve in this inactive position It is best to place all dry pieces and pump motor in the original packaging for storage To avoid condensation or corrosion problem do not cover or wrap pump motor with plastic bags Store the pump motor and accessories in a dry place The storage s temperature should be controlled between 0 degrees Celsius 32 degrees Fahrenheit and 40 degrees Celsius 104 degrees Fahrenheit SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 TROUBLESHOOTING GUIDE DIABALLLLUU OH LLLLLOA uLLLL o TROUBLE CAUSE FILTER MOTOR The motor is not plugged in FAILS TO START The GFCI RCD circuit breaker is tripped Motor too hot a
18. e motion screw the strainer nut 24 back onto the threaded connector 26 see drawing 2 Finger tighten the strainer nut 24 onto the threaded connector 26 Grasp the plunger valve assembly Make sure the step washer 23 is in place In a clockwise motion screw the plunger valve union back onto the threaded connector 26 see drawing 3 In a clockwise motion turn the plunger valve handle to close position Ensure the plunger valve is securely closed This will prevent water from flowing out during filling of the pool see drawing 4 1 NOTE Never cover the vacuum release valve 36 unless it is damaged or leaking Replace the vacuum release valve immediately SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English POOL INLET NOZZLE amp PLUNGER VALVE SETUP optional In a counter clockwise motion unscrew plunger valve union from the threaded strainer connector 26 see drawing 5 Be careful not to lose the step rubber washer 23 Place the plunger valve on the ground in a safe place In a counter clockwise motion unscrew the strainer nut 24 from the threaded connector 26 Leave the flat washer 25 on the connector 26 INSIDE Install the nozzle and plunger valve at the vili ors upper position of pool inlet From the inside of the pool liner insert the connector 26 into one of the pre cut
19. edly your electrical system may have a defect Turn off circuit breaker and call an electrician to correct the problem Let the motor cool down and restart again Adjust the chlorine and pH level Consult your local swimming pool supply stores Load with filter sand see sand loading instructions Set valve to FILTER position Operate the filter for longer periods Clean the strainer screen at the inlet Clear any obstructions in the intake hose by discharging it inside pool wall Tighten hose nuts check hoses for damage check pool water level Clean the pre filtering basket more often Backwash filter Install the nozzle at the upper position of the pool inlet and the strainer at the lower position of the pool outlet Remove about 1 of sand if necessary Remove any pool vacuuming device attached to the system line urn off pump clear any debris or obstruction in the outlet remove all air from the filter pump and turn pump on again Turn off pump if water leaking from the vacuum release valve then release valve needs to be replaced Contact Intex Service Center immediately to order replacement You may cover release valve with the cap temporarily if you ensure that the strainer cover strainer grid is installed and you Do Not run the pump while pool is occupied Fill pool to correct water level Clean strainer screens at pool inlet Tighten hose nuts check hose for damage Contact Intex service center Remove 6 way
20. ee see drawing 28 Do not use this setting with pump running SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English OPERATING INSTRUCTIONS continued Initial startup and operation Before operating be sure that All the hoses have been connected and tightened securely and correct amount of filter sand have been loaded The entire system is connected to a grounding type receptacle protected by a ground fault circuit interrupter GFCI or residual current device RCD CAUTION The filter control valve has a closed position The pump should never be on when the valve is in the closed position If the pump is operated with the valve closed explosive situation could exist 1 Turn both plunger valve handles fully counter clockwise until they stop This opens the valves to allow water to flow into the sand filter pump With water flowing into sand filter pump the water pressure will allow the air trapped inside to escape from the air release valves 19 When all the air has escaped water will flow out of the valves 19 When this occurs gently finger tighten the valves 19 in a clockwise direction IMPORTANT To prevent air lock open the lower plunger valve connected inlet hose first and then the upper plunger valve connected outlet hose Open the air release valves wait until water starts to flow out of the air release valves close air release val
21. holes with the washer remaining on the connector to be placed against the inside of the liner wall Before assembly lubricate the threads with a petroleum jelly With the flat side of the strainer nut 24 facing the outside wall of the liner in a clockwise motion screw the strainer nut 24 back onto the threaded connector 26 see drawing 6 Finger tighten the adjustable pool inlet nozzle 27 and the strainer nut 24 onto the threaded connector 26 Grasp the plunger valve assembly Make sure the step washer 23 is in place In a clockwise motion screw the plunger valve union back onto the threaded connector 26 see drawing 7 In a clockwise motion turn the plunger valve handle to close position Ensure the plunger valve is securely closed This will prevent water from flowing out during filling of the pool see drawing 8 NOTE Never cover the vacuum release valve 36 unless it is damaged or leaking Replace the vacuum release valve immediately Adjust the direction of nozzle head pointing away from the pool outlet for a better circulation result see drawing 9 The pool liner is now ready to fill with water Consult the above ground pool owner s manual for filling instructions SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 PRODUCT SPECIFICATIONS The sand filter removes suspended particles but does not san
22. illing of the pool may have brackish water requiring extra water additives and extra filtering time Do not allow swimming in pool until the pH level is balanced Consult your local swimming pool supply store for instructions Chlorinated water may damage lawns gardens or shrubbery as children play in the pool and splash water outside the pool Lawn areas underneath the pool liner will be destroyed Note that some types of grass may grow through the liner Filter run time depends on pool size weather and usage level Experiment with various run times so as to produce clean clear water A CAUTION Concentrated chlorine solutions may damage the pool liner Always follow the chemical manufacturer s directions and the health and hazard warnings A CAUTION Allowing the water to freeze will damage the sand filter and void the warranty If anti freeze solution is needed use only propylene glycol Propylene glycol is non toxic and will not damage plastic system components other anti freezes are highly toxic and may damage plastic components in the system Before emptying your pool for long term storage or relocation be sure the water is directed towards an acceptable drain water receptacle away from the house Check local regulations for specific directions regarding disposal of swimming pool water Switch off the unit and disconnect power cord from electrical outlet When the pool is empty disconnect all hoses from pump and plunger valves an
23. itize your pool Pool chemisiry is a specialized area and you should consult your local pool service specialist for details Mode SF80110 SF70110 SF60110 Power 110 120 Volt AC 110 120 Volt AC 110 120 Volt AC Amperage 3A 4 8A 6A Maximum working pressure 2 bar 30 psi 2 bar 30 psi 2 bar 30 psi Recommended filtering No 20 silica sand No 20 silica sand No 20 silica sand media quantity 23 Kg 50 Lbs or 35 Kg 77 Lbs or 55 Kg 121 Lbs or glass sand 25 Kg glass sand 38 Kg 55 Lbs 84 Lbs Recommended filtering No 20 silica sand or glass sand Particle size range 0 45 to 0 85 media Not included mm 0 018 to 0 033 inches Uniformity Coefficient less than 1 75 Limited Warranty see Limited Warranty NOTE NOT SUITABLE FOR USE WITH KCP LOW SALT AUTOMATIC SALTWATER SYSTEM MODEL 6110 6220 SETUP INSTRUCTIONS TOOLS REQUIRED One 1 Phillips screwdriver Pump location and mounting The system must be installed on a solid level and vibration free base Provide a location protected from the weather moisture flooding and freezing temperature Provide adequate access space and lighting for routine maintenance Pump motor requires free circulation of air for cooling Do not install the pump in a damp or non ventilated location A team of 2 or more people is recommended for setting up this product Motor pre filtering assembly setup Remove the sand filter and its accessories from the packaging carefully and
24. nd overload protection is shut off FILTER DOESN T Improper chlorine or pH levels CLEAN POOL No filtering media in tank Wrong 6 way valve setting position Excessively dirty pool The strainer screen is restricting the water flow FILTER DOESN T PUMP WATER OR FLOW IS VERY Excessively dirty pool SLOW Sand media clogged with dirt Nozzle and strainer connections are reversed Crusting or caking on the filtering sand surface Pool vacuuming device attached to the system The vacuum release valve on the plunger valve is activated The vacuum release valve on the plunger valve is leaking Clogged inlet or discharge An air leak on the intake line PUMP DOESN T Low water level WORK Strainer screen clogged up An air leak on the intake hose Faulty motor or the impeller is jammed 6 WAY VALVE Sand tank o ring missing COVER LEAKING Sand tank o ring dirty Flange clamp not tight 6 way valve damage HOSE LEAKING Hose nut not securely tight Hose connection fitting o ring L shape o ring missing TIMER IS Possible inner timer TIMER CAN T BE SET PRESSURE GAUGE Clogged inlet of the pressure gauge DOESN T WORK Pressure gauge damage SAND IS FLOWING Sand is too small EM INTO THE Sand bed is calcified SOLUTION Line cord must be plugged into a 3 wire outlet that is protected by a Class A Ground Fault Circuit Interrupter or RCD Reset circuit breaker If circuit breaker trips repeat
25. oduct while standing in water or when your hands are wet Do not use an appliance leakage current interrupter ALCI in place of a GFCI since the ALCI will not protect people mE postion this product away from pool so as to prevent children from climbing on it and access the pool Do not operate this product when pool is occupied To reduce the risk of entrapment hazard never enter the pool if suction strainer component is loose broken cracked damaged or mning Replace loose broken damaged cracked or missing suction strainer components immediately Never play or swim near suction fittings Your body or hair may be trapped causing permanent injury or drowning u To prevent equipment damage and risk of injury always turn pump off before changing the filter control valve position Never operate this product above the maximum working pressure stated on the filter tank Hazardous Pressure Improper tank valve cover assembly could cause the valve cover to blow off and cause serious injury property damage or death This product is intended to be used only for the purposes described in the manual FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE ELECTRIC SHOCK ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH A CAUTION This product is for use with storable pools only Do not use with permanently installed pools A storable pool is constructed so that it is capable of being readily disassembled for storage
26. our local authorities to determine if there is a regulation in your area regarding above the ground swimming pool filter pumps If yes then the product can be mounted to a platform using the two holes located in the base See drawing 14 3 The product can be mounted on a cement base or onto a wooden plat form to prevent accidental falling over mounting holes are 6 4 mm in diameter and spaced 100 mm for model SF80110 spaced 115 mm for model SF70110 amp SF60110 apart e Use two bolts and lock nuts with a maximum of 6 4 mm in diameter Model SF80110 100 mm Model SF70110 amp 60110 115 mm SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 SETUP INSTRUCTIONS continued Sand loading IMPORTANT Use No 20 silica sand or glass sand with particle size range 0 45 to 0 85 mm 0 018 to 0 033 inches and a Uniformity Coefficient less than 1 75 NOTE Before loading the tank with sand ensure the center pipe hub assembly is securely in place at the bottom of the tank and vertically centered inside the tank 1 Place the sand shield 6 over the top of the center pipe Pour the sand into the tank at a slow rate see drawing 15 2 Fill the tank approximately half way remove the sand shield 6 from the top see drawing 16 3 Evenly distribute the sand inside the tank then fill the tank with some water to provide a cushioning effect when the remaining sand is poure
27. st stay away from this product and electrical cord s Assembly and disassembly by adults only Risk of electric shock Connect only to a grounding type receptacle this product is provided with a ground fault circuit interrupter If replacement of the plug or cord is needed use only identical replacement parts 2 Always unplug this product from the electrical outlet before removing cleaning servicing or making any adjustment to the product The unit is provided with a ground fault circuit interrupter GFCI To test the GFCI push the test button The GFCI should interrupt power Push the reset button power should be restored If the fails to operate in this manner The GFCI is defective If the GFCI interrupts power to the pump without the test button being pu ted ground current is flowing indicating the poss of an electric shock Do not use this pump Disconnect the pump an have the problem corrected by a qualified service representative before Un Do not bury the electrical cord Locate the cord where it will not be damaged by lawn mowers hedge trimmers and other equipment To reduce the risk of electric shock replace damaged cord immediately Use a qualified electrician to replace the cord To reduce the risk of electric shock do not use extension cords timers plug adaptors or converter plugs to connect unit to electric supply provide a properly located outlet Do not attempt to plug in or unplug this pr
28. the receptacle is protected by a GFCI RCD Use a qualified electrician to install the GFCI RCD which has a maximum rate of 30mA Do not use a portable residual current device PRCD To reduce the risk of electric shock do not use extension cords timers plug adaptors or converter plugs to connect unit to electric supply provide a properly located outlet Do not attempt to plug in or unplug this product while standing in water or when your hands are wet Never operate this product above the maximum working pressure stated on the filter tank Always switch off pump before changing the 6 way valve position Operating this product without water flowing through the system can cause a build up of hazardous pressure which can result in an explosive situation serious injury property damage or death Never test this pump with compressed air Never operate the system with water temperature above 35 C 95 F 6 way valve positions and function Valve Position Function Water Flow Direction FILTER Normal filtration and regular see drawing 23 vacuuming of pool to pool see drawing 24 filter media to valve waste drain outlet see drawing 25 leveling the sand bed after backwashing to valve waste drain outlet see drawing 26 lowering pool level or to drain the pool outlet bypassing the filter media see drawing 27 without going through the filter media pool bypassing the filter media Shuts off all flow to filter and pool
29. time to learn CPR and first aid Instruct anyone who is supervising pool users about potential pool hazards and about the use of protective devices such as locked doors barriers etc Instruct all pool users including children what to do in case of an emergency Always use common sense and good judgement when enjoying any water activity Supervise supervise supervise For additional information on safety please visit The Association of Pool and Spa Professionals The Sensible Way to Enjoy Your Aboveground Onground Swimming Pool www nspi org American Academy of Pediatrics Pool Safety for Children www aap org Red Cross www redcross org e Safe Kids www safekids org Home Safety Council Safety Guide www homesafetycouncil org Toy Industry Association Toy Safety www toy tia org SAVE THESE INSTRUCTIONS 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 LIMITED WARRANTY Your Sand Filter Pump has been manufactured using the highest quality materials and workmanship All Intex products have been inspected and found free of defects prior to leaving the factory This Limited Warranty applies only to the Sand Filter Pump and accessories listed below The provisions of this Limited Warranty apply only to the original purchaser and is not transferable This Limited Warranty is valid for the period noted below from the date of the initial retail purchase Keep your original sales receipt with this man
30. tions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This Limited Warranty does not apply if the products are subject to negligence abnormal use or operation accident improper operation improper voltage or current contrary to operating instructions or to damage by circumstances beyond Intex s control including but not limited to ordinary wear and tear and damage caused by exposure to fire flood freezing rain or other external environmental forces This Limited Warranty applies only to those parts and components sold by Intex The Limited Warranty does not cover unauthorized alterations repairs or disassembly by anyone other than Intex Service Center personnel DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN OR REPLACEMENT IF YOU ARE MISSING PARTS OR NEED ASSISTANCE PLEASE CALL US TOLL FREE FOR U S AND CANADIAN RESIDENTS 1 800 234 6839 OR VISIT OUR WEBSITE WWW INTEXSTORE COM Proof of Purchase must accompany all returns or the warranty claim will be invalid SAVE THESE INSTRUCTIONS Page 24
31. ual as proof of purchase will be required and must accompany warranty claims or the Limited Warranty is invalid Sand Filter Pump Warranty 2 Years Hoses Plunger Valves amp Fittings Warranty 180 days If a manufacturing defect is found within the periods noted above please contact the appropriate Intex Service Center listed in the separate Authorized Service Centers sheet The Service Center will determine the validity of the claim If the Service Center directs you to return the product please carefully package the product and send with shipping and insurance prepaid to the Service Center Upon receipt of the returned product the Intex Service Center will inspect the item and determine the validity of the claim If the provisions of this warranty cover the item the item will be repaired or replaced at no charge Any and all disputes regarding the provisions of this Limited Warranty shall be brought before an informal dispute settlement board and unless and until the provisions of these paragraphs are carried forth no civil action may be instituted The methods and procedures of this settlement board shall be subject to the rules and regulations set forth by the Federal Trade Commission F T C IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND IN NO EVENT SHALL INTEX THEIR AUTHORIZED AGENTS OR EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL DAMAGES OR LIABILITIES Some states or jurisdic
32. ves NOTE The plunger valve is equipped with a vacuum release valve that will automatically activate to minimize the suction at the pool outlet if the outlet is blocked This is an additional safety feature to prevent suction entrapment The vacuum release valve will reset once the blockage is removed and the pump is switched off To restart the system the air must be removed from the filter pump per previous step Ensure the drain waste outlet on the 6 way valve is not covered and directed to a proper draining receptacle Ensure the pump is off depress the 6 way valve and turn it to the BACKWASH position see drawings 24 amp 29 IMPORTANT To prevent damage to the 6 way valve always depress the valve handle before turning Always switch off pump before changing the 6 way valve position Switch on the pump see drawing 30 Water is circulating backward through the sand media and to waste drain outlet Backwash until a clear flow of water is observed in the waste drain outlet or through the drain sediment window NOTE The initial backwash of the filter is recommended to remove any impurities or fine sand particles in the sand media TIMER OFF ON SAVE THESE INSTRUCTIONS Page 15 195PO SAND FILTER PUMP ENGLISH 7 5 X 10 3 PANTONE 295U 06 28 2013 195 English OPERATING INSTRUCTIONS continued Switch off the pump change the 6 way valve to RINSE position see drawing 25 Switch on the
Download Pdf Manuals
Related Search