Axis T8133
Contents
1. useful trainings webinars tutorials and guides Regulatory Information Europe C This product complies with the applicable CE marking directives and harmonized standards e Electromagnetic Compatibility EMC Directive 2004 108 EC See Electromagnetic Compatibility EMC on page 2 e Low Voltage LVD Directive 2006 95 EC See Safety on page 3 e Restrictions of Hazardous Substances RoHS Directive 2011 65 EU See Disposal and Recycling on page 3 A copy of the original declaration of conformity may be obtained from Axis Communications AB See Contact Information on page 3 Electromagnetic Compatibility EMC This equipment has been designed and tested to fulfill applicable standards for e Radio frequency emission when installed according to the instructions and used in its intended environment e Immunity to electrical and electromagnetic phenomena when installed according to the instructions and used in its intended environment USA This equipment has been tested using a shielded network cable STP and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio comm2. 46 46 272 18 00 Fax 46 46 13 61 30 www axis com AXIS T8133 Midspan 30W Safety Information Read through this Installation Guide carefully before installing the product Keep the Installation Guide for future reference Hazard Levels ADANGER Indicates a hazardous situation which if not avoided will result in death or serious injury AWARNING Indicates a hazardous situation which if not avoided could result in death or serious injury ACAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE Indicates a situation which if not avoided could result in damage to property Other Message Levels Important Indicates significant information which is essential for the product to function correctly Indicates useful information which helps in getting the most out of the product AXIS T8133 Midspan 30W Safety Instructions e The Axis product shall be installed by a trained professional e The Axis product shall be used in compliance with local laws and regulations To use the Axis product outdoors or in similar environments it shall be installed in an approved outdoor housing Store the Axis product in a dry and ventilated environment e Avoid exposing the Axis product to shocks or heavy pressure e Do not install the product on unstable brackets surfaces or walls e Use only applicable tools when installing the Axis product Excessive for
3. Equipment Disposal and Recycling When this product has reached the end of its useful life dispose of it according to local raws and regulations For information about your nearest designated collection point contact your local authority responsible for waste disposal In accordance with local legislation penalties may be applicable for incorrect disposal of this waste Europe A MI This symbol means that the product shall not be disposed of together with household or commercial waste Directive 2012 19 EU on waste electrical and electronic equipment WEEE is applicable in the European Union member states To prevent potential harm to human health and the environment the product must be disposed of in an approved and environmentally safe recycling process For information about your nearest designated collection point contact your local authority responsible for waste disposal Businesses should contact the product supplier for information about how to dispose of this product correctly This product complies with the requirements of Directive 2011 65 EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS China This product complies with the requirements of the legislative act Administration on the Control of Pollution Caused by Electronic Information Products ACPEIP Contact Information Axis Communications AB Emdalav gen 14 223 69 Lund Sweden Tel
4. INSTALLATION GUIDE AXIS T8133 Midspan 30W COMMUNICATIONS Liability Every care has been taken in the preparation of this document Please inform your local Axis office of any inaccuracies or omissions Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice Axis Communications AB makes no warranty of any kind with regard to the material contained within this document including but not limited to the implied warranties of merchantability and fitness for a particular purpose Axis Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing performance or use of this material This product is only to be used for its intended purpose Intellectual Property Rights Axis AB has intellectual property rights relating to technology embodied in the product described in this document In particular and without limitation these intellectual property rights may include one or more of the patents listed at http www axis com patent htm and one or more additional patents or pending patent applications in the US and other countries Equipment Modifications This equipment must be installed and used in strict accordance with the instructions given in the user documentation This equipment contains no user serviceable components Unauthorized equipme
5. ce could cause damage to the product Do not use chemicals caustic agents or aerosol cleaners Use a clean cloth dampened with pure water for cleaning Use only accessories that comply with technical specification of the product These can be provided by Axis or a third party e Use only spare parts provided by or recommended by Axis Do not attempt to repair the product by yourself Contact Axis support or your Axis reseller for service matters Transportation e When transporting the Axis product use the original packaging or equivalent to prevent damage to the product AXIS T8133 Midspan 30W Installation Guide This Installation Guide provides instructions for installing AXIS T8133 on your network Installation Steps 1 Make sure the package contents tools and other materials necessary for the installation are in order See page 7 2 Study the hardware overview See page 8 3 Study the specifications See page 8 Install the hardware See page 10 Package Contents e AXIS T8133 Midspan 30W e AC power cable e Printed materials Installation Guide this document AXIS T8133 Midspan 30W Hardware Overview 1 Port LED indicator 2 DATA amp POWER OUT 3 DATAIN Indicators Port LED Indicated Behavior Yellow On Power is on power is active Green On A remote terminal is connected Green Blinking Overload state or sh
6. e Installing AXIS T8133 1 Connect the midspan DATA IN to the network switch using a network cable 2 Connect the midspan DATA amp POWER OUT to the camera using the network cable that has been connected to the camera 3 Connect the midspan to a grounded earthed mains power outlet 100 240 V AC using the supplied power cable 4 Make sure that the LEDs on the midspan indicate the correct conditions See Indicators on page 8 10 AXIS T8133 Midspan 30W 1 Port LED indicator 2 DATA amp POWER OUT connect to Axis product 3 DATA IN connect to network e Do not cover the midspan or block the airflow to the PoE with any foreign objects Keep the midspan away from excessive heat and humidity and free from vibration and dust e Ensure that the cable length from Etherhet network source to the terminal does not exceed 100 m 330 ft The PoE is not a repeater and does not amplify the Ethernet data signal e Ifa splitter is to be used make sure it is connected close to the terminal and not on the midspan e No ON OFF switch exists simply plug the midspan into an AC power source Troubleshooting AXIS T8133 does not power up e Remove and re apply power to the device and check the indicators during power up sequence 11 AXIS T8133 Midspan 30W e Verify that the voltage at the power inlet is between 100 240 V AC e Verify that the power inlet cable is funct
7. ional The powered device does not operate e Verify that the powered device is designed for PoE operation Verify that a standard Category 5 5e 6 straight wired cable with four pairs is used e Verify that the input Ethernet cable is connected to the DATA IN port e Verify that the powered device is connected to the DATA amp POWER OUT port e If an external power splitter is in use verify that it works e Verify that there is no short over on any of the twisted pair cables or over the RJ45 connectors e If possible reconnect the same powered device into a different midspan The end device operates but there is no data link e Verify that the port on the front panel is continuously lit Verify that a standard Category 5 5e 6 straight wired cable with four pairs is used e Verify that the Ethernet cable length is less than 100 m 330 ft from the Ethernet source to the load remote terminal e Ifan external power splitter is in use verify that it works e f possible reconnect the same powered device into a different midspan Warranty Information For information about Axis product warranty and thereto related information see www axis com warranty 12 13 Installation Guide Ver M1 14 AXIS T8133 Midspan 30W Date October 2013 Axis Communications AB 2013 Part No 53460
8. nt changes or modifications will invalidate all applicable regulatory certifications and approvals Trademark Acknowledgments AXIS COMMUNICATIONS AXIS ETRAX ARTPEC and VAPIX are registered trademarks or trademark applications of Axis AB in various jurisdictions All other company names and products are trademarks or registered trademarks of their respective companies Apple Boa Apache Bonjour Ethernet Internet Explorer Linux Microsoft Mozilla Real SMPTE QuickTime UNIX Windows Windows Vista and WWW are registered trademarks of the respective holders Java and all Java based trademarks and logos are trademarks or registered trademarks of Oracle and or its affiliates UPnPTM is a certification mark of the UPnPTM Implementers Corporation Support Should you require any technical assistance please contact your Axis reseller If your questions cannot be answered immediately your reseller will forward your queries through the appropriate channels to ensure a rapid response If you are connected to the Internet you can s download user documentation and software updates e find answers to resolved problems in the FAQ database Search by product category or phrase e report problems to Axis support staff by logging in to your private support area e chat with Axis support staff selected countries only visit Axis Support at www axis com techsup Learn More Visit Axis learning center www axis com academy for
9. ort circuit Specifications Operating Conditions The Axis product is intended for indoor use AXIS T8133 Midspan 30W Mode Temperature Humidity Operating 20 C to 40 C 4 F to 104 F 10 90 RH non condensing Storage Conditions Mode Temperature Humidity Storage 20 C to 70 C 4 F to 158 F 10 90 RH non condensing Power Consumption Input Voltage 100 240 V AC 50 60 Hz Maximal Input Current 0 8 Ampere Available Output Power max 30 Watts Nominal Output Voltage 55 V DC Power over Ethernet Plus PoE IEEE 802 3at Type 2 Class 4 Ethernet Interface Input Data In Ethernet 10 100 1000Base T RJ45 female socket Output Data amp Power Out Ethernet 10 100 1000Base T plus 55 V DC RJ45 female socket with DC voltage on wire pairs 4 5 amp 7 8 AXIS T8133 Midspan 30W Connectors and Buttons For specifications and operating conditions see page 8 Network Connector RJ45 Ethernet connector Supports Power over Ethernet PoE The product shall be connected using a shielded network cable STP All cables connecting the product to the network switch shall be shielded STP and intended for their specific use Make sure that the network switch is properly grounded For information about regulatory requirements see Regulatory Information on page 2 Install the Hardwar
10. unications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Canada his Class B digital apparatus complies with Canadian CES 003 Europe his digital equipment fulfills the requirements for RF emission according to the Class B limit of EN 55022 his product fulfills the requirements for immunity according to EN 55024 office and commercial environments Australia New Zealand his digital equipment fulfills the requirements or RF emission according to the Class B limit of AS NZS CISPR 22 COR Bld 777B RRR CT C DABA RERE CSAS SCE AN EULTWETD COREBDIVATPTLE Y I RERICHELTEAENGE ZE ase sg EHC TCeEPHUET ARE Bich CIELO RU gue LT FEL Korea o 71712 7ASSCs AA 8171212 4 FE 780 ASE AS SHOE do DE AAAA ASE ASUC Safety This product complies with IEC EN UL 60950 1 Safety of Information Technology
Download Pdf Manuals
Related Search