Shuttle SX79R5 barebone
Contents
1. SX79R5 Quick Guide English Front Panel F1 5 25 Bay F2 3 5 Bay F3 Eject Button F4 Open Door F5 Power Switch amp Power LED etree i F6 HDD LED F7 USB3 0 Ports F8 USB2 0 Port F9 Mic In F10 Headphone F11 USB2 0 Port amp Fast Charger Back Panel B1 AC Power Socket B2 Serial Port Perforation B3 SPDIF Out Port B4 USB3 0 Ports B5 eSATA Power Port B6 eSATA amp USB2 0 Ports S386 SS36E ame B7 Clear CMOS Button eee ee al Hil B8 Front Out L R Port 7 B9 Side Surround L R Port B10 Surround Back L R Port B11 Center Bass Port B12 Line In Port B13 LAN amp USB2 0 Ports B14 Wireless LAN Perforation Optional B7 2x LAN amp 4x USB 2 0 Ports Clear CMOS Button eSATA amp 2x USB 2 0 Ports a f p eSATA Power Port J8 hki USB 3 0 Ports I4 USB Header at em i fem USB2 USB3 D AUX IN Connector CN1 Aa e eee be SPDIF Out Connector D w SPDIF1 Po r bi i ma P 4 ai CPU Fan connector FAN1 hE TE a COM Connector COM1 USB Header USB1 j RaT oR Front Out Line In Ports Center Bass Surround Back Side Surround Ports 11 Front Audio Header JP2 HH Tee faa n Ak j FE CIR Header JP5 X79 Chipset LPC Header JP1 D 310 USB3 0 Header JP6 f 2 0 Serial ATA SATA 3 4 13 0 Serial ATA SATA 1 2 A Ey i E TF A CSE iF sialic aT Fan connector FAN2 PCI2. 72 2 144 pin 48 2 96 pin 4 First release retention tab at and location then lift up the metal plate on top of CPU socket Chassis 9 HEEE BEBE ii gt SEE Sees Po fed fe Ln Remove the protective membrane 3 Check that the latches are closed and the memory module is firmly installed G Complete 1 Replace the cover and refasten the thumbscrews Metal load plate A DO NOT touch socket contacts To protect the CPU socket always replace the protective socket cover when the CPU is not installed 5 Orientate the CPU and socket aligning the yellow triangle on the corner of the CPU with the triangle on the socket or you may align the CPU notches with the socket alignment keys Make sure the CPU is perfectly horizontal insert the CPU into the socket A Repeat to install additional memory modules if required 2 Complete D Mini PCle card Installation he Pees ae EEE a Please load the optimized BIOS values 1 Install the Mini PCle card into the Mini PCle slot mSATA Slot and affix it with screws H Install eSATA HDD Triangle Pin1 Marking on the CPU Metal load plate Take out the eSATA to SATA Cable and External SATA Power Cable from the accessory box 2 Plug the eSATA to SATA cable to the eSATA port and plug the External SATA Power Cable to the eSATA power
3. Data_P 12 B_Data_N 13 Ground 14 B_TX_P 15 B_TX_N 16 Ground 17 B_RX_P 18 B_RX_N 19 5VCC 20 NA 11 12 13 14 15 16 17 18 19 20 Front Audio Header JP2 1 MIC_L 2 GND 3 MIC_R 4 Front_Detect 5 LINE_R 6 Mic_detect 7 sense 8 NA 9 LINE_L 10 Line_Detect 10 8 6 4 2 gt Safety Information Read the following precautions before setting up a Shuttle XPC CAUTION Incorrectly replacing the battery may damage this computer Replace only with the same or equivalent as recommended by Shuttle Disposal of used batteries according to the manufacturer s instructions Laser compliance statement The optical disc drive in this PC is a laser product The drive s classification label is located on the drive CLASS 1 LASER PRODUCT EAUTION INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM A Begin Installation 3 Place the rack in the chassis and refasten the rack For safety reasons please ensure that the power cord is disconnected before opening the case A 1 Unscrew 3 thumbscrews of the chassis cover application area 2 Slide the cover backwards and upwards A Please do not apply excess amount of thermal paste Connect the Serial ATA Cable to motherboard A 8 Tear off the protective membrane from the bottom of ICE module Remove the protective socket mylar from the CPU socket 9 Screw the ICE module to the mainboard Note to press down on the opposite diagonal
4. Express x16 Slots ILGA 2011 Mini PCle Slot Mini PCle slot with mSATA support 2x 240 pins DDR3 Ai DIMM Slots 2x 240 pins DDR3 peii i P T f Jig uu al DIMM Slots ony ee aa oe E v 2p od Ce rer er T ATX Power Connector ATX1 ATX2 D Power Header JP4 62R SX79R0 0601 SX79R5 English Spanish Korean Traditional Chinese Japanese French German Quick Guide Jumper Sett ing S S PDIF OutPut Connector JP3 CIR Header JP5 1 Ground 1 5V 2 VCC 2 NA 3 SPDIFO ee 3 Ground nj elele 4 GPIO1 12 3 5 GPIO2 1 2 3 4 5 com Header COM1 Power Header JP4 1 DCD 2 RXD 1 HD_LED 2 PWR_LED 3 TXD 4 DTR 3 HD_LED 4 GND 5 Ground 6 DSR 5 RST_SW 6 PWR_SW 7 RTS 8 CTS 7 GND 8 GND 9 Ring 10 NA 9 NULL 10 NA CPU Fan Connectors SPEED_SENSE 5 AUX IN Connector CN1 1 AUX IN Left 2 Ground 12V Ground 3 Ground PWM_CTRL 4 AUX IN Right a 43 2 1 FAN1 FAN2 USB Header USB1 USB2 USB3 Q eSATA Power Port 1 5V_USB 2 5V_USB 1 5V 3 USB A 4 USB B 2 3 3V 5 USB A 6 USB B 3 12V 7 GND 8 GND 4 GND 9 NA 10 NULL ele Op LPC Header JP1 1 12V 2 5V 3 5VSB 4 SERIRQ 5 CLK_48M 6 CLK_33M 7 SIO_RST 8 LFRAME 9 LAD3 10 LAD2 11 12V 12 3VSB 13 Ring 14 LDRQO 15 SIO_PME 16 LAD1 17 LADO 18 4 3 3V 19 GND 20 NA 11 12 13 14 15 16 17 18 19 20 G USB 3 0 Header JP6 1 5VCC 2 A_RX_N 3 A_RX_P 4 Ground 5 A_TX_N 6 A_TX_P 7 Ground 8 A_Data_N 9 A Data P 10 OC 11 B_
5. corner while tightening each screw 10 Connect the fan connector Serial ATA Power Cable Serial ATA Cable Serial ATA Power Cable Serial ATA Cable B CPU and ICE Installation F Accessories Installation 1 Unfasten expansion slot bracket screws 1 Unfasten the ICE fan thumbscrews on the back of the chassis Remove the back panel bracket and put the bracketacide 2 Unfasten the four ICE module attachment screws and unplug the fan connector A The maximum size acceptable for display card is 267mm x 98mm x 18mm C Memory module Installation 1 Unlock the DIMM latch s ae YII re 2 Align the memory module s cutout with the DIMM slot notch Slide the memory module into the DIMM slot a as EE E PCI Express x1 6 slots Fan Connector Lgl z z i AX A DDR3 memory module has a cutout so it can only fit in one direction 3 Remove the ICE module from the chassis and put it aside A This 2011 pin socket iS fragile and easily damaged Always use 2 Install the PCI Express x16 card into the PCI Express x16 slot extreme care when installing a CPU and limit the number of times that you remove or change the CPU Before installing the CPU make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU EEES EENE 3 Secure the bracket Card PCB lt en gt Follow the steps below to correctly install the CPU into the motherboard CPU socket
6. port 3 Connect the eSATA to SATA Cable and External SATA Power Cable to the HDD E Peripheral Installation A Please be aware of the CPU orientation DO NOT force the CPU into the socket of prevent bending the pins on the socket and damaging the CPU 1 Loosen the purse lock and separate the Serial ATA and power cables eSATA port 6 Close the metal load plate lower the CPU socket lever and lock in place 2 Place the HDD and optical drive in the rack and secure with screws eSATA power port l l from the side 7 Spread thermal paste evenly on the CPU surface Serial ATA ODD eSATA to SATA Cable Metal load plate External SATA Power Cable Load lever Serial ATA HDD Retention tab 53R SX79R3 2001 9 The product s color and specification will depend upon the actually shipping product
Download Pdf Manuals
Related Search