Gorenje GI64324X dishwasher
Contents
1. If the water hardness has been set on a value above H3 and the 3 1 option is activated the 3 1 OPTION LIGHT 9 flashes warning of a setting error because these products are not suitable for use with very hard water This does not prevent the use of the option but the washing results might not be of the best 13 14 User instructions DELAYING THE PROGRAM available in all programs except the soak program The PROGRAM DELAY button 6 can be pressed to delay the start of the washing program by up to 12 hours This means that the dishwasher can be operated at the time of day of your choice Press the PROGRAM DELAY button 6 again the 3 FIGURE DISPLAY 12 will show the number of hours of delay with which the appliance will Start After setting the delay start the program press the START PAUSE button 4 for a few seconds until the PROGRAM STARTED light 5 starts flashing The appliance will prewash the dishes after which the program delay set previously will come into effect To cancel the program delay once the wash has started proceed as follows e Press the START PAUSE button 4 for a few seconds until the PROGRAM STARTED light 5 stops flashing e Press the PROGRAM DELAY button 6 several times until the program delay returns to zero e Press the START PAUSE button 4 to start the program 1 14 15 3 119 7512 User instructions CEN D START THE DISHWASHER After carrying out a2. Contents CEN 1 Safety and operating instructions 2 Installation and hook up 3 Description of the controls 9 4 Operating instructions 17 5 Cleaning and maintenance 29 6 Troubleshooting 33 Thank you for choosing one of our products You are advised to read this manual carefully it contains all the information you need about the right conditions for the proper safe use of your dishwasher The individual sections are laid out to provide you with a step by step guide to all your appliance s functions the texts are easy to understand and are complete with detailed illustrations Recommendations are given for the correct use of the baskets spray arms containers filters washing programs and for operating the controls Following the cleaning instructions provided here will keep your dishwasher s performance at peak levels in the long term This user friendly manual will provide answers to all your questions about use of the dishwasher INSTALLATION INSTRUCTIONS these are intended for the qualified technician who must carry out the installation hook up and testing of the appliance USER INSTRUCTIONS these consist of recommendations for using the appliance a description of its controls and of the correct cleaning and maintenance procedures i li lI i i h he Fa a Safety instructions 1 Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE IT MUST ALWAYS BE KEP
3. F F WESS MY CUTLERY BASKET The basket has removable top grids into which items of cutlery can be inserted to keep them properly spaced and allow water to pass between them effectively The cutlery supports and central lid are in the bag of accessories The central lid is intended to act only as a cover do not place the cutlery in it Depending on model the grids may vary in shape The cutlery should be arranged in an orderly manner inside the basket with the handles pointing downwards Take care during loading to avoid injury from the knife blades The basket is suitable for all types of cutlery except those long enough to interfere with the upper spray arm Ladles wooden spoons and cooking knives can be placed in the upper basket making sure that the knife blades do not protrude from the basket ZTNRRRNY i a A ie LNA 25 26 User instructions UPPER BASKET It is recommended to load the upper basket with small or medium sized items such as glasses small plates tea or coffee cups shallow bowls and light objects made from heat resistant plastic If the upper basket is used in the lowermost position it can also be loaded with serving dishes provided they are only slightly soiled LOADING THE UPPER BASKET Load plates facing forward cups bowls etc must always be facing downwards The left side of the basket can be loaded with cups and glasses on two levels In the centre section plates
4. conventional washing cycles 3 1 products might create problems such as a white deposit poor drying results and residues left on dishes The introduction of detergent into the rinse aid dispenser even in liquid form will damage the dishwasher 4 3 General warnings and recommendations Before using the dishwasher for the first time it is advisable to read the following recommendations concerning dish types to be washed and their loading There are generally no constraints on the washing of domestic dishes but in certain cases it is necessary to take their characteristics into account Before loading the dishes into the baskets it is necessary to e remove coarse food remains e g bones fish bones etc which may clog the filter or damage the wash pump e soak any pots or pans with burnt on food remains on the bottom to facilitate removal then load them into the LOWER BASKET There is no need to pre wash the dishes under running water before loading them into the baskets since this only wastes water Correct loading of the dishes helps ensure optimal washing results ees e a F y rA Q i r r f a f D n Q a _ oT F l WARNING e Make sure that the dishes are securely in place so that they cannot tio over or obstruct the rotation of the spray arms during the washing cycle e Do not place very small objects in the baskets as these could fall and obstruct the spray arms or the wash pump e Containers such as cup
5. e If available connect the dishwasher to a hot water supply up to 60 TO CUT DOWN ON DETERGENT CONSUMPTION AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment To avoid using excessive amounts of detergent and to save on electricity observe the following e separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures e donot pour the detergent directly on the dishes REMOVING THE DISHES At the end of the washing program wait at least 20 minutes before removing the dishes to allow them to cool down To prevent any water droplets on the upper basket from falling on the dishes in the lower basket it is advisable to unload the lower basket first and then the upper basket S User instructions 4 Operating instructions Once the dishwasher has been correctly installed prepare for use as follows e Adjust the water softening system e Add the regenerating salt e Add the rinse aid and detergent 4 1 Using the water softening system The amount of scale contained in the l L water water hardness index can cause Ne whitish staining on the dry dishes which i tend to become dull over time The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water g The dishwasher is factory set for water hardness level 3 average h
6. YOUR DEALER THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY A QUALIFIED TECHNICIAN THIS DISHWASHER MUST BE USED BY ADULTS USE BY PERSONS WITH REDUCED MENTAL AND OR PHYSICAL CAPABILITIES IS ONLY PERMITTED UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR THEIR SAFETY KEEP CHILDREN AWAY FROM DETERGENTS AND PACKAGING MATERIALS PLASTIC BAGS POLYSTYRENE ETC AND NEVER ALLOW THEM TO APPROACH OR PLAY WITH THE DISHWASHER SINCE IT MIGHT CONTAIN DETERGENT RESIDUES CAPABLE OF CAUSING PERMANENT DAMAGE TO THE EYES MOUTH AND THROAT AND EVEN LEADING TO SUFFOCATION DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MAY CAUSE AN EXPLOSION DO NOT LOAD DISHES THAT ARE SOILED WITH ASH WAX OR PAINTS CEN gt Safety instructions LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN PUTING PEOPLE AT RISK NEVER LEAVE THE DISHWASHER DOOR OPEN PEOPLE MIGHT TRIP OVER IT DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE KNIVES OR OTHER SHARP ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE DOWN OR LAID HORIZONTAL IN THE TOP BASKET TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM THE BASKET AQUASTOP MODELS THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK WHEN THE AQU
7. a free standing dishwasher is absolutely forbidden If the appliance is not built in and is therefore accessible on on side the door hinge area must be covered for safety reasons injury hazard The covering fixtures are available as an accessory from specialist dealers or the After Sales Service To build in the dishwasher the special kit must be purchased from authorised dealers or the After Sales Service Some models are equipped with only one adjustable foot at the rear which can be adjusted by turning the screw on the lower front part of the appliance aa I lI 1 i h he a _ a Installation instructions 2 1 Water supply connection Preventing the risk of clogging or damage if the water pipe is new or has not been used for a long time before connecting to the water supply check that the water is clear and free of impurities to prevent damage to the appliance The dishwasher must always be connected to the water system with new hoses old or used hoses must never be reused CONNECTING TO THE WATER SUPPLY a ay Connect the intake hose to a cold water supply with 3 na gas thread inserting the filter A supplied with the gt dishwasher Take care to screw the hose firmly into a wa place with your hands and then complete by oy tightening about 1 4 of a turn with pliers ah In dishwashers equipped with the ACQUASTOP A device the filters is already fitted inside the threaded uS ring b The dishw
8. a further reduction in the bacteria level If the temperature falls during this stage of the program e g because the door is opened or due to a power blackout the program lights 3 flash to warn that the anti bacteria effect is not guaranteed 1 2 Average power consumption with the softener set on level 2 The cycle duration and power consumption may vary according to the water and room temperatures and the type and amount of dishes A The washing cycle will not take place if the dishwasher door is left open or not properly closed 11 12 User instructions 3 2 Washing programs The dishwasher is equipped with a control panel an an 3 FIGURE DISPLAY 12 described in chapter 3 Description of the controls from which it is possible to carry out all the power switch on switch off and programming operations Before starting a washing program make sure that e The water supply tap is open e The correct amount of detergent has been added to the dispenser e The baskets have been correctly loaded e The spray arms are able to rotate freely and without obstruction e The dishwasher door is securely closed 1 14 15 3 1197512 13 2 10864 PROGRAMMING In this dishwasher model all the programming operations are possible only with closed door A porta aperta suWith open door on thel 3 FIGURE DISPLAY 12 will appear the symbols SELECTION PROGRAM Keep pressing the PROGRAM SELECTION button 2 un
9. and saucers can be loaded vertically into the supports provided Loading examples ra Iz Q fay rere mi Sr MTD ETELE Y SHA T hth Sk ail User instructions CEN JU Depending on the models the basket may be equipped with some or all of the following accessories Supports for cups or long objects ladles spoons on the left can be tipped to the vertical position when not in use Long stemmed glass holder on the left to use simply lift and fix onto the hooks provided Cutlery racks on the right designed for knives and teaspoons for teaspoons pull out the sliding support The racks can be tipped to the vertical position when not in use Fixed or movable racks in the middle The movable supports can be fixed vertical resting on the bottom of the basket when not in use or set in the intermediate position as required fre if rt Ph 1 ee aa eel hel Peet ee Be F a ke uxt k a J al 2 2 fa rm User instructions ADJUSTING THE UPPER BASKET The height of the top basket can be adjusted to allow large dishes or pans to be placed in the bottom basket The adjustment procedure may be type A or B depending on the dishwasher model purchased Version A pull out with adjustment in two positions e Pull out both the basket guides e Remove the stops first releasing them as shown in the diagram e Pull out the basket e Inserire nella guida la
10. coppia di ruote superiore o inferiore secondo la regolazione desiderata e Return the stops to their original position e The left hand and right hand sides of the basket must always be set at the same height 28 Version B with adjustment in three positions on both sides The sides of the basket must always be set at the same height e Raise the basket by pulling on the top edge 1 to the first or second catch depending on the height required e To lower the basket first release it by pulling the release lever 2 Adjustment is also possible with the basket loaded but in this case when lowering the basket it should be held steady with one hand to avoid knocking the dishes ks a OS ki k User instructions 5 Cleaning and maintenance Before carrying out any work always unplug the appliance from the electrical supply or switch off the all pole disconnection device 5 1 General warnings and recommendations Avoid the use of acidic or abrasive detergents Clean the outer surfaces and door lining of the dishwasher regularly using a soft cloth moistened with water or with a normal detergent suitable for painted surfaces Clean the door gaskets with a damp sponge Periodically once or twice a year it is advisable to clean the tank and gaskets using a soft cloth and water to remove any deposits CLEANING THE WATER INTAKE FILTER The water intake filter A located at the outlet of the w
11. part of the door the detergent dispenser is on the left and the rinse aid dispenser is on the right With the exception of the SOAK program before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser The rinse aid on the other hand should only be added as required 19 20 User instructions ADDING THE RINSE AID The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining it is automatically added to the water during the final rinse cycle from the container situated on the inner side of the door To add rinse aid Open the door Rotate the container cap anticlockwise by of a turn and remove it Add the rinse aid until the container is full approximately 140 cc The optical level indicator on the side of the cap should be completely obscured Refill the rinse aid when the optical level indicator becomes clear again or when the rinse aid warning light illuminates Replace the cover and turn it in a clockwise direction Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam ADJUSTING THE RINSE AID DISPENSER SETTING The dishwasher is factory set for medium water hardness However it possible to change the setting by turning the dispenser s selector to the desired position the amount of rinse aid dispensed is proportional to the selector position To a
12. point is possible to program the dishwasher again If the malfunction persists contact your authorised Service Centre 33 User instructions TECHNICAL DATA Width Depth measured flush with the outer edge of the control panel Height depending on models Capacity Water supply pressure Electrical characteristics 34 997 599 mm Free standing 600 mm Semi integrated 570 mm Free standing from 850 mm to 870 mm from 890 mm to 910 mm Semi integrated from 820 mm to 870 mm from 860 mm to 910 mm 12 Standard place settings min 0 05 max 0 9 MPa min 0 5 max 9 bar See rating plate
13. ASTOP DEVICE IS TRIPPED CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM THE WATER SUPPLY IMMEDIATELY AFTER INSTALLING THE DISHWASHER PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW IF THE DISHWASHER FAILS TO OPERATE CORRECTLY DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE DO NOT ATTEMPT TO REPAIR THE APPLIANCE REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL EQUIPMENT ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN REPAIRS CARRIED OUT BY UNAUTHORISED PERSONS WILL INVALIDATE THE WARRANTY AS WELL AS POSING A POTENTIAL HAZARD TO THE USER THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE The manufacturer declines all responsibility for damage to persons or property resulting from failure to observe the above precautions from tampering with even a single component of the appliance or from the use of non original spare parts gt Installation instructions 2 Installation and hook up Remove the polystyrene basket retainers Position the appliance in the desired place of installatio
14. D ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID WASTING ELECTRICITY us mad Safety instructions CEN gt OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE CUT OFF THE MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN LOCKS DOORS ETC THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE BY ENSURING THIS PRODUCT IS DISPOSED OF CORRECTLY YOU WILL HELP PREVENT POTENTIAL NEGATIVE CONSEQUENCES FOR THE ENVIRONMENT AND HUMAN HEALTH WHICH COULD OTHERWISE BE CAUSED BY INAPPROPRIATE WASTE HANDLING OF THIS PRODUCT THE SYMBOL X ON THE PRODUCT OR ON THE DOCUMENTS ACCOMPANYING THE PRODUCT INDICATES THAT THIS APPLIANCE MAY NOT BE TREATED AS HOUSEHOLD WASTE INSTEAD IT SHALL BE HANDED OVER TO THE APPLICABLE COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT DISPOSAL MUST BE CARRIED OUT IN ACCORDANCE WITH LOCAL ENVIRONMENTAL REGULATIONS FOR WASTE DISPOSAL FOR MORE DETAILED INFORMATION ABOUT TREATMENT RECOVERY AND RECYCLING OF THIS PRODUCT PLEASE CONTACT YOUR LOCAL CITY OFFICE YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE PRODUCT IN THE EVENT OF A FAULT DISCONNECT THE DISHWASHER FROM THE ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANSIT IF IN DOUBT CONSULT
15. RCE THE PLUG MUST BE ACCESSIBLE AFTER INSTALLATION NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD IN THE EVENT OF DAMAGE TO THE SUPPLY CORD HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE DO NOT USE ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD IT IS NECESSARY TO INSTALL IN THE FIXED WIRING AN ALL POLE DISCONNECTION DEVICE HAVING A GAP BETWEEN CONTACTS OF AT a LEAST 3 5MM AFTER INSTALLATION THE DISCONNECTION DEVICE HAS TO BE EASY TO REACH m THE CONNECTION TO THE MAINS MUST BE CARRIED OUT BY A An QUALIFIED TECHNICIAN IN ACCORDANCE TO THE SCHEME SHOWN Ke a BELOW AND THE REGULATIONS IN FORCE L brown N blue yellow green 20 mm manufacturer or an Authorized Technical Service Centre in order to A In the event of damage to the supply cord have it replaced by the avoid any risk Installation instructions FOR GREAT BRITAIN ONLY THIS APPLIANCE MUST BE EARTHED Fuse replacement If the mains lead of this appliance is fitted sae with a BS 1363A 13amp fused plug to Gq TINA change a fuse in this type of plug use an A A nel t A S T A approved fuse to BS 1362 type p AL JA and proceed as follows way Alle SN Bie 1 Remove the fuse cover A and fuse B WW 2 Fit replacement 13A fuse into fuse NOT ees cover a ATION 3 Refit both i
16. T INTACT TOGETHER WITH THE DISHWASHER BEFORE USING THE APPLIANCE CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN IN COMPLIANCE WITH THE REGULATIONS IN FORCE THIS APPLIANCE IS INTENDED FOR DOMESTIC USE AND COMPLIES WITH THE EEC DIRECTIVES 73 23 89 336 INCLUDING 92 31 AND 93 68 CURRENTLY IN FORCE INCLUDING THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE WASHING AND DRYING OF DISHES ANY OTHER USE SHALL BE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR USES OTHER THAN THOSE DESCRIBED ABOVE THE NAME PLATE FEATURING THE TECHNICAL DATA SERIAL NUMBER AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE DOOR THE NAME PLATE ON THE INNER EDGE OF THE DOOR MUST NEVER BE REMOVED DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME SEPARATE THE VARIOUS MATERIALS WHICH MAKE UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT OBSTRUCTE
17. alt water inside the tank may lead to corrosion Be careful not to confuse the salt and detergent packages adding detergent to the salt container will damage the water softening system ADJUSTING THE WATER SOFTENING SYSTEM available in all programs except the soak program The dishwasher is equipped with an electronic device for adjusting the water softening setting according to the hardness of the water To adjust the water softening setting proceed as follows 1 14 15 3 1197 512 13 2 10864 e Keep the PROGRAM DELAY button 6 pressed for a few seconds until the H symbol followed by the set value appears on the 3 FIGURE DISPLAY 12 e The PROGRAM DELAY button 6 can be pressed again to select the most suitable hardness value h 0 h 1 h 2 h 5 Refer to the Water hardness table to select the value e To exit the programming mode press the START PAUSE button 4 or do not touch the keypad for 2 seconds to allow the system to exit the mode automatically User instructions CEN 2 WATER HARDNESS TABLE WATER HARDNESS German Degrees dH French Degrees dF SEU oe 0 7 Setting N 1 NO SALT so 5 8725 h 0 16 23 26 40 h 1 24 31 41 60 h 2 32 47 61 80 h 3 48 58 81 100 h 4 Contact your local water board for information on the hardness of your water supply 4 2 Using the rinse aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner
18. ardness 41 60 dF 24 31 dH When using water of medium hardness the regenerating salt container should be refilled after approximately 20 washing cycles The salt container can hold approximately 1 7 Kg of salt in grains The container is situated at the bottom of the dishwasher After removing the lower basket unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher Before replacing the cap remove any salt residues from around the opening e When using the dishwasher for the first time in addition to the salt it is also necessary to add one litre of water to the container e Each time the salt container is refilled make sure that the cap is securely closed The mixture of water and detergent must never penetrate the salt container as this would compromise the operation of the regeneration system In the event of this occurring the warranty will be invalidated e Only use regenerating salt specially formulated for domestic dishwashers If using salt tablets do not fill the container completely 17 nN Y 18 User instructions e Do not use table salt as it contains insoluble substances which over time may damage the water softening system e When necessary refill the regenerating salt container before starting the washing program In this way the excess saline solution will be immediately removed by the water the prolonged presence of s
19. asher can also be connected to a hot water supply not exceeding 60 C Supplying the appliance with hot water cuts down the washing time by approximately 20 minutes but slightly reduces its effectiveness Make the connection to the domestic hot water supply using the same procedure described for connecting to the cold water supply DRAIN CONNECTION Insert the dishwasher s drain hose into a drain pipe having a diameter of at least 4 cm or alternatively place it inside the kitchen sink using the plastic support provided taking care not to crush or excessively bend the hose It is important to prevent the hose from coming loose and falling For this purpose the plastic support is equipped with a hole for tying it to the wall or water tap z MAX 100 cm emmed mre ee e ee e ee e e ee ede e e e e e min 30 m The free end should be positioned at a height of between 30 and 100 cm and should never be submerged in water If a horizontal drain extension hose is used for a maximum of 3 m the drain hose can be placed at a maximum height of 85 cm from the ground Installation instructions CEN gt 2 2 Electrical connection and precautions CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE AND MEET THE REGULATIONS IN FO
20. ater supply tap needs to be cleaned periodically _ After having closed the water supply tap unscrew the end of the water intake hose remove the filter A and clean it delicately under running water Reassemble filter A in its seat and carefully screw the water intake hose back into position CLEANING THE SPRAY ARMS The spray arms can be easily removed for periodic cleaning of the nozzles to prevent possible clogging Wash them under running water and carefully replace them in their seats checking that their rotary movement is in no way impeded e Toremove the upper spray arm unscrew locking ring R e To remove the lower spray arm simply lift it up pulling by the central part 29 s CEND 30 User instructions CLEANING THE FILTER UNIT It is advisable to periodically inspect the centre filter C and if necessary to clean it To remove the filter grip the tabs turn them anticlockwise and lift upwards push the centre filter D from the underside to remove it from the micro filter separate the two parts which make up the plastic filter by pressing the body of the filter in the zone shown by the arrows remove the centre filter by lifting it upwards GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE The filters should be cleaned under running water using a stiff brush When removing the filter take care that there are no food residues on it If any residues fall into the washing
21. djust the rinse aid setting rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it Then use a screwdriver to rotate the rinse aid selector to the desired position Replace the cap turning it clockwise The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains If on the other hand the dishes are sticky or have white streaks it is necessary to reduce the rinse aid setting User instructions C EN D ADDING THE DETERGENT To open the detergent dispenser cap lightly press the button P Add the detergent and close the cap carefully During the washing cycle the dispenser will be opened automatically pe os st mE pa Hh iF a lade a i NOTH e MIN WL y Fa EET i ii i Lr i m1 i j L e When a program with hot prewash is selected see program table extra detergent must be placed in the cavity G H depending on models e Use only detergents specially formulated for dishwashers For optimal washing results it is important to use a good quality detergent e The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results Once opened the detergent packs should not be kept for too long otherwise the detergent loses its effectiveness e Do not use detergents formulated f
22. es If in doubt as to the fastness of the colours it is advisable to wash just a few items at a time for approximately one month 23 z i j User instructions E 4 4 Using the baskets The dishwasher has a capacity of 12 place settings including serving dishes LOWER BASKET The lower basket receives the full force of the lower spray arm and should therefore be used for the toughest items with a heavier degree of soiling All types and combinations of loads are AC permitted provided that the dishes pots and C f A ll of DD pans are arranged with all the soiled surfaces a yet J gtr Ss exposed to the water jets coming from the S ae bottom To make the most of the space inside the basket when loading large items certain models are equipped with tip up supports for plates in 2 or 4 sections With tip up supports BOTTOM BASKET INSERTS Some models are equipped with bottom basket inserts which improve the drying of dishes The inserts are supplied in the accessories bag to use them simply fit them into place as shown 2 i aaa pne Tg i User instructions CEN gt LOADING THE LOWER BASKET Carefully load flat plates soup plates dessert and serving dishes positioning them vertically Pots pans and their covers must be loaded upside down When loading soup plates and dessert bowls be sure to leave a gap between them Loading examples Met F
23. ets 1 Average power consumption with the softener set on level 2 2 The cycle duration and power consumption may vary according to the water and room temperatures and the type and amount of dishes A 10 The washing cycle will not take place if the dishwasher door is left open or not properly closed User instructions CEN gt onde DURATION CONSUMPTION PROGRAM SELECTION TYPE AND GRADE OF DIRT Silda EO E SONEN 2 LITRES 1 KWh 2 6 p PANS AND DISHES ars fii AWAITING COMPLETION OF Cold prewash 15 5 I THE LOAD i DELICATE DISHES WITH Wash at 38 C i p 2 P LIGHT DIRT WASHED Cold rinse 45 13 0 85 QUIC IMMEDIATELY AFTERUSE Rinse at 58 C DISHES WITH NORMAL When the AUTO program is selected the 8 cut TET T O dishwasher recognises the type of dirt and AUTO 40 50 ga 70 P IMMEDIATELY pelea USE automatically adjusts the e parameters as appropriate DISHES WITH NORMAL A 9 bio P DIRT WASHED Cele lise 100 17 1 35 ECO IMMEDIATELY AFTER USE Rinse at 70 C Dry cp E VERY DIRTY PANS AND Haa 0 10 E DISHES WASHED a Meee 110 20 1 50 HYGIENE P IMMEDIATELY AFTER USE Bae at 70 C ry Only run the soak program with partial load The DELAYED START 6 and 3 1 8 options cannot be used with the soak program To execute programs 6 7 8 9 10 users must first press the extra programs button 10 The HYGIENE PLUS program terminates with an anti bacteria rinse that ensures
24. he table below which indicates the most appropriate program according to dish type and degree of soiling DURATION CONSUMPTION PROGRESS SELECTION TYPE AND GRADE OF DIRT PROGRAM MINUTES WATER POWER 2 LITRES 1 KWh 2 eae Cold rinse the Ai PANS AND DISHES FOR Pity RINSING AND DRYING eee at 70 C 45 9 0 90 a ry Cold prewash Wash at 45 C ES a a Cold rinse 59 12 090 Rinse at 70 C Dry E VS When the AUTO program is selected the NORMAL DIRT WASHED dishwasher recognises the type of dirt and e IMMEDIATELY AFTER USE automatically adjusts the washing parameters as 60 70 appropriate Cold prewash DISHES WITH NORMAL kk bio DIRT EVEN WITH DRIED oN Wash at 52 C 180 see ki RESIDUES Rinse at 66 C Dry Prewash at 40 C VERY DIRTY PANS AND Wash at 70 C Cy DISHES EVEN WITH DRIED 2 cold rinses 150 15 1 50 ON RESIDUES Rinse at 70 C Dry The HYGIENE PLUS program terminates with an anti bacteria rinse that ensures a further reduction in the bacteria level If the temperature falls during this stage of the program e g because the door is opened or due to a power blackout the program lights 3 flash to warn that the anti bacteria effect is not guaranteed Reference program as per EN 50242 standard Some models feature an intermediate rinse See energy label Reference program for laboratories Detergent 20g in dispenser 10g in door or tablet Configuration see photo in Using the bask
25. ll the operations described above correctly to start the dishwasher simply press the START PAUSE button 4 for a few seconds until a beep sounds the PROGRAM STARTED light 5 starts to flash The 3 FIGURE DISPLAY 12 will show the duration of the program in minutes The duration time is only approximate because it depends on the washing conditions quantity of dishes water temperature etc and is also continually updated as the washing program progress The 3 FIGURE DISPLAY 12 shows the estimated duration of the washing program If it is necessary to open dishwasher door during the washing cycle there will be a 1 minute delay before the program can be resumed After correctly closing the door press the START PAUSE button 4 again This operation may negatively affective the progress of the washing cycle 13 2 10864 END PROGRAM The end of the program is indicated by a short signal acoustic and from the End visual notification on 3 FIGURE DISPLAY 12 By pressing the PROGRAM SELECTION button 2 the End visual signal will vanish from the display and the dishwasher is ready to continue a new cycle 15 aa CEN 16 User instructions TO SAVE ON ENERGY AND PROTECT THE ENVIRONMENT e Always try to run the dishwasher fully loaded e Do not wash the dishes in running water e Use the washing program that is most appropriate for each type of load e Do not carry out any preliminary rinsing
26. n The back or sides of the dishwasher may be placed up against walls or other furniture units If the dishwasher is installed near a heat source fit the special insulating panel to prevent overheating and malfunction of the appliance To ensure stability install integrated or built under dishwashers only under continuous worktops and screw them to the adjacent units To facilitate the installation procedure the intake and drain hoses can be positioned in any direction make sure that the hoses are not kinked crushed or pulled too tightly Make sure to tighten the locking ring nut once the pipes have been placed in the direction required A hole at least 8 cm in diameter is required to allow the power supply cable and pipes to pass Level the appliance on the floor using its adjustable feet This operation is essential for ensuring correct operation of the dishwasher Building in a dishwasher underneath a ceramic hob is absolutely forbidden A dishwasher can be built in underneath a conventional hob provided there is no break in the kitchen worktop and the dishwasher and hob are installed and secured correctly so that no hazards are generated When installing the dishwasher in a compartment next to one or more other appliances it is essential to comply with all the recommendations provided by the appliance s manufacturer minimum distances installation procedures etc For free standing models only Installing a hob on top of
27. ned properly check that the correct amount of detergent has been added there is regenerating salt inside the special container the dishes are being loaded correctly the selected program is suitable for the dish types and their degree of soiling all the filters are clean and positioned correctly e the spray arm nozzles are not obstructed e there is no object obstructing the rotation of the spray arms 31 32 User instructions If the dishes fail to dry or remain dull check that e there is rinse aid inside the special container e the rinse aid dispenser setting is correct e the detergent used is of good quality and has not lost its effectiveness for example through incorrect storage with the box left open If the dishes show signs of streaking staining etc check that e the rinse aid dispenser setting is not too high If there are visible traces of rust inside the tank e the tank is made of steel and therefore any rust marks are due to external elements fragments of rust from the water pipes pots cutlery etc Special products are commercially available to remove such marks e check that the amount of detergent being used is correct Certain detergents can be more corrosive than others e check that the cap of the salt container is securely closed and that the water softening setting is correct If after following the above troubleshooting instructions the problem persists call the neares
28. nto plug cover is lost the plug must not be used until a correct replacement is fitted Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug Replacement fuse covers are available from your local electrical store i The fuse cover must be refitted when changing a fuse and if the fuse User instructions CEN D 3 Description of the controls 3 1 Front panel All the dishwasher control are grouped on the front panel Programming and option selection are only possible with the door closed 1 14 15 3 1197512 Lt 13 2 10864 1 ON OFF BUTTON 2 SELECTION PROGRAM BUTTON 3 PROGRAM PHASE INDICATOR LIGHTS 4 START PAUSE BUTTON 5 PROGRAM STARTED STOP INDICATOR LIGHT 6 PROGRAM DELAY BUTTON 7 PROGRAM DELAY LIGHT 8 3 1 OPTION BUTTON 9 3 1 OPTION LIGHT 10 EXTRA PROGRAM BUTTON 11 EXTRA PROGRAM LIGHT 12 3 FIGURE DISPLAY remaining time program delay alarms 13 NO SALT WARNING LIGHT 14 NO RINSE AID WARNING LIGHT 15 DOOR HANDLE Flashes while the program is in progress stops flashing and remains on at the end of the program or if the program is interrupted intentionally or due to a malfunction C EN gt PROGRAM RINSE 2 DELICATE 3 AUTO 60 70 IEC DIN 4 BIO EN 50242 5 HYGIENE PLUS GE User instructions SETTING THE WASHING PROGRAM To select the most suitable program for the dishes to be washed refer to t
29. or washing dishes by hand because they produce a great deal of foam and may negatively affect the operation of the dishwasher e Add the correct amount of detergent An insufficient amount of detergent will result in a partial removal of dirt from the dishes whereas an excessive amount is wasteful and does not improve the washing results e The market offers liquid and powder detergents with differing chemical compositions which may contain phosphates or be phosphate free but contain natural enzymes Detergents containing phosphates are more effective against grease and starch at temperatures above 60 C Enzyme detergents on the other hand are also effective at lower temperatures from 40 to 557 and are more easily biodegradable With enzyme detergents it is possible to obtain at low temperatures comparable results to those which can only be achieved at 65 C using traditional detergents For the safeguarding of the environment we recommend the use of phosphate and chlorine free detergents 21 CEN 22 User instructions e 3 1 Products If you wish to use detergents which already contain salt and rinse aid check whether your dishwasher is fitted with the 3 1 option button on the Controls description page and then refer to the section which explains how to use this function If the button is not provided we recommend the use of conventional products separate detergent salt and rinse aid because with
30. pit they might block hydraulic components or foul the spray arm nozzles lt is essential to thoroughly clean the filters according to the above instructions the dishwasher cannot function if the filters are clogged Carefully replace the filters in their seats to avoid damaging the wash pump PROLONGED DISUSE Run the soak program twice in succession Unplug the power cord from the socket Leave the door slightly open in order to prevent the formation of unpleasant odours inside the washing tank Fill the rinse aid dispenser Shut off the water supply tap IONS le A p II etriieat BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE e Check that there are no deposits of sludge or rust inside the water pipe if there are allow the water to run from the water supply tap for a few minutes e Plug the power cord back into the socket e Reconnect the water intake hose and open the tap again TROUBLESHOOTING MINOR PROBLEMS In some cases it is possible to remedy minor problems by referring to the following instructions If the program fails to start check that the dishwasher is connected to the electrical power supply there is no power failure the water tap is open the dishwasher door is properly closed If water remains inside the dishwasher check that e the drain hose is not kinked e the drain siphon is not obstructed e the dishwasher filters are not clogged If the dishes are not being clea
31. s bowls glasses and pots should always be loaded with the opening facing downwards and with any cavities at an angle to allow the water to drain out e Do not stack dishes or place them in such a way that they cover one other e Do not place glasses too close together because they may knock against each other and break or there might be staining at the point where they touch MAKE SURE that the items being washed are dishwasher safe Items which are not dishwasher safe e Wooden dishes pots or pans these may be damaged by the high washing temperatures e Handcrafted items these are rarely suitable for washing in a dishwasher The relatively high water temperatures and the detergents used may damage them e Plastic dishes heat resistant plastic dishes must be washed in the upper basket e Dishes and objects in copper tin zinc or brass these tend to stain e Aluminium dishes items made from anodised aluminium may lose their colour e Silverware silver items may stain e Glass and crystal in general glass and crystal objects can be washed in the dishwasher However certain types of glass and crystal may become dull and lose their clearness after many washings Therefore for these items we recommend using the least aggressive program available e Decorated items the decorated objects available on the market are generally able to withstand washing in the dishwasher although the colours may fade after a great many wash
32. t After Sales Centre WARNING any operations performed on the appliance by unauthorised persons are not covered by the warranty and shall be paid for by the user User instructions END 6 Troubleshooting The dishwasher is equipped with a self diagnostics system that is capable of detecting and signalling a number of possible faults TABLE OF FAULTS DETECTED BY THE SELF DIAGNOSTICS SYSTEM FAULT E1 E2 E3 E4 E5 E6 E7 E8 E9 DESCRIPTION The anti flooding system where present has been tripped The water level limitation system has tripped The appliance cannot heat the water The temperature sensor is disconnected The appliance cannot take in the water The appliance cannot drain the water from the tank The dishwasher cannot measure the precise water quantity that has been loaded Problem on the water distribution system to the baskets Water intake system malfunction If an alarm occurs the appliance interrupts the program in progress and signals a fault e Alarms E1 E2 E3 E4 E8 and E9 interrupt the current program immediately e The E5 E6 alarms interrupts the running program once the cause is resolved it will bring bach the execution of the program e The alarm E7 is visualized at the end of the cycle that comes however brought to the end since the operation of the dishwasher is not harmed To reset an alarm is necessary e Open and close the door or turn off and on the machine At this
33. til the indicator light corresponding 3 to the desired program illuminates CANCELLING THE CURRENT PROGRAM To annul the current program press the START PAUSE button 4 for a few seconds until the PROGRAM STARTED indicator light 5 stops flashing Now press the START PAUSE button 4 again until PO appears on the display about 10 seconds User instructions CEN gt CHANGIN THE PROGRAM To modify the program keep the START PAUSE button 4 pressed for a few seconds until the PROGRAM STARTED indicator light 5 stops flashing then select the new program following the instructions provided above press the START PAUSE button 4 again and keep it pressed for a few seconds until the indicator light 5 starts to flash again 1 14 15 3 119 7 512 13 2 10864 3 1 OPTION BUTTON available in all programs except the soak program By pressing the button 8 you activate the 3 1 option confirmed when the relative light comes on This option has been studied for the use of dishwashing powder or tablets with integrated substances in place of regenerating salt or rinse aid known on the market as 3 in 1 or triple action products in this case the dishwasher will use the product in an optimal way avoiding salt and rinse aid consumption which could already be found in the dishwasher Note When selecting the 3 1 button it is normal that the salt and rinse aid lights remain on if their containers are empty
Download Pdf Manuals
Related Search