SYBA SI-PEX40059
Contents
1. Follow the on screen instructions to complete the installation 5 Restart Windows to complete the installation To Verify Driver I nstallation 1 Right click My Computer and click Manage 2 Select Device Manager 3 Look for the following Windows XP 2003 Double click SCSI and RAID controller Marvell 91xx SATA 6G Controller should be displayed Windows Vista 7 Double click Storage controllers Marvell 91xx SATA6G Controller should be displayed2. G6501975SE91201 PCI Express SATA II 6G Card User Manual Ver 1 00 All brand names and trademarks are properties of their respective owners Features and Benefits e Compliant with PCI Experss Specification v2 0 and backward compatible with PCI Express 1 e Compliant with Serial ATA Specification 3 0 e Supports communication speeds of 6 0Gbps 3 0Gbps and 1 5Gbps e Hot plug and Hot Swap for SATA hard drives e Supports Native Command Queuing NCQ Supports Port Multiplier FIS based switching or command based switching e Supports ATA and ATAPI commands e Compatible with SATA 6G 3G and 1 5G Hard Drives e Supports Windows XP Server 2003 Vista 7 32 64 bit Bus Interface e PCI Express x1 Connectors e 2x SATA connectors e 1x IDE connectors System Requirements PCI Express enabled system with one available PCI Express slot Windows XP Server 2003 Vista 7 32 64 bit Package Contents 1 x PCle SATA III 6Gb s Card 1 x SATA Cable 1 x IDE Cable 1 x Driver CD 1 x User Manual 1 x Low Profile Bracke Note Contents may vary depending on country market e o p e Hardware Installation 1 Turn off your computer 2 Unplug the power cord and remove your computer s cover 3 Remove the slot bracket from an available PCle slot 4 To install the board carefully align the card s bus connector with the selected PCle slot on the motherboard Push the board down firmly 5 Attac
3. ad Driver to install the driver 3 Insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive please select Marvell 9128 SATA 6G Controller D Marvell 9128 Driver miniport Floppy32 mv9 1xx In then press Next Change D to match your CD ROM drive letter 4 Continue with Windows OS installation For An Existing Installation 4 Please insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive 2 At the Windows desktop click Start and then Run 3 Type D Marvell 91 28 Driver drvSetup exe click OK Change D to match your CD ROM drive letter 4 Follow the on screen instructions to complete the installation 5 Restart Windows to complete the installation For Windows 7 x64 Vista x64 For A New Windows Installation 1 Follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press Load Driver to install the RAID driver 3 Insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive please select Marvell 9128 SATA 6G Controller D Marvell 9128 Driver miniport Floppy64 mv91xx in then pres Next Change D to match your CD ROM drive letter 4 Continue with Windows OS installation For An Existing Installation 1 Please insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive 2 At the Windows desktop click Start and then Run 3 Type D Marvell 9128 Driver drvSetup exe click OK Change D to match your CD ROM drive lett 4
4. h your internal devices to the PCle SATA 6G Card 6 Replace the slot bracket s holding screw to secure the card 7 Replace the computer cover and reconnect the power cord Driver Installation For Windows XP Server 2003 32bit For A New Windows Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Marvell 9128 Driver miniport Floppy32 folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press F6 to install the driver 3 When prompted press S to specify the location of the driver 4 Insert the floppy disk and then press Enter 5 Scroll to Marvell shared library install first using the arrow keys and press Enter to select 6 Press S again to select the second device 7 Scroll to Marvell 9128 SATA Controller 32bit Driver and press Enter to select 8 Press Enter to complete the installation of drivers 9 Continue with the Windows OS installation For An Existing Windows Installation 1 Please insert the driver CD bundled with PCle SATA 6G Card into your CD ROM Drive 2 At the Windows desktop click Start and then Run 3 Type D Marvell 9128 Driver drvSetup exe click OK Change D to match your CD ROM drive letter 4 Follow the on screen instructions to complete the installation 5 Restart Windows to comp
5. lete the installation For Windows XP Server 2003 64bit For A New Windows Installation A new installation requires a floppy disk for the driver installation To make this Sloppy disk copy the contents of the Marvell 9128 Driver miniport Floppy64 folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press F6 to install the driver 3 When prompted press S to specify the location of the driver 4 Insert the floppy disk and then press Enter 5 Scroll to Marvell shared library install first using the arrow keys and press Enter to select 6 Press S again to select the second device 7 Scroll to Marvell 9128 SATA Controller 64 bit Driver and press Enter to select 8 Press Enter to complete the installation of drivers 9 Continue with Windows OS installation For An Existing Installation 1 Please insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive 2 At the Windows desktop click Start and then Run 3 Type D Marvell 9128 Driver drvSetup exe click OK Change D to match your CD ROM drive letter 4 Follow the on screen instructions to complete the installation 5 Restart Windows to complete the installation For Windows 7 Vista 32bit For A New Windows Installation 1 Follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press Lo
Download Pdf Manuals
Related Search