Belkin F9K1118 router
Contents
1. 42 Troubleshooting Support and Warranty 44 Troubleshooting xz ssepe rune Ne UE 44 Teghinica Supports 2 3 id vas REL han AI Rc dye 49 Belkin International Inc Limited 2 Year Product Warranty 50 Regulatory Information 53 Statement scence rue pide gad eed lites 53 GETTING STARTED What s in the Box AC1800 DB Wireless AC Gigabit Router Ethernet cable attached to router Power supply attached to router Network information card attached to router Quick Setup Guide Initial Setup Where to Place Your Router For the best results place the Router next to your modem in an open location away from large metal objects and magnets such as those found in speakers Raising the Router above floor level can improve the strength of your wireless signal How to Set It Up Connect Your AC1800 DB Router Turn off your modem by disconnecting its power supply Some modems have a battery backup this will need to be disconnected at this time as well Connect your Router to your modem using the cable already attached Power up your modem by plugging in its power supply If your modem has a battery backup it can be reconnected at this time you may need to hold the reset button for 10 seconds Power up your Router by plugging in its power supply Connect to Your Router SEA PELE NO 52. belkin WIRELESS AC GIGABIT ROUTER AC1800 DB F9K1118 8820 01245 Rev BOO TABLE OF CONTENTS Getting Started IER Ria anam min 1 Ale Du Mc M RP n 1 Initial SOW dme IRR RB Rr anne tas 1 Manually Set Up Your Internet Connection 10 Additional Capabilities 22 Adding Other USB Devices 24 USB Print and Storage Center 25 GUCStACCESS nde tid ete Lid n Tus akon FA e 26 Media Server by myTwonky 27 Website Filters Powered by Norton 28 Intellistream QOS d cutee cem quick at 29 IPVG Config retibD eue dresser are RE OCA 32 Getting to Know Your 33 Holt Padel o ie ell M derbi aga etait ne AA RE DADA SR 33 Back Paie wad glue ru da DI RUE nS esate 34 Technical Details eue deu dunnanuanuanunagaanaans 35 Technical Poatures iien koe bea ee x Rie RUE ERE tar 35 System Requirements 36 Using Your ROUTE occo ir irukan 37 Auto Update on Your Belkin Router 37 Updating the Router s Firmware via the Web Interface 38 Resetting the 41 Restoring your Router to Factory Default
3. Firmware Version CAN ium LI aw n hs t Check tor New Firmware Version Checa lemese feed emm Meme ftmt 6 Click on Firmware Update toward the bottom 7 Click the Choose File button toward the middle of the screen to search for the file you saved previously Note The firmware version in the image above is depicted as an example Your file name will vary depending on your model and version 39 USING YOUR ROUTER 8 Select the firmware file by left clicking on it and then click the Open button in the lower right corner of the window This will take you back into the Router s interface Firmware Version 03 02 20 2017 12 9 37 Check tor New Firmware Version Meca lemese Update Firmware Choose File io Me chosen 9 Click the Update button 10 A prompt asking Are you sure you want to continue with upgrading will appear Click OK 11 A second prompt will open telling you the Router will not respond during the upgrade and warning you not to remove the power supply from the Router Click OK once more Congratulations The firmware has been updated successfully 40 Resetting the Router Reset Button Red The Reset button is used in rare cases when the Router may function improperly Resetting the Router will restore the Router s normal operation while maintaining the programmed settings You can also restore the factory default
4. You can share a USB hard drive or flash drive to your network via your Router s USB port Once connected you can share files and music with other computers and devices within your network Plug your USB hard drive into the USB port on the back of your Router You can manually check the status of your shared drive by visiting the USB Print and Storage Manager If you have difficulty sharing a drive on your network please see the Troubleshooting section of this manual A few USB hard disks require more power than the Router s USB port provides In these cases you may notice the drive failing to come on or remaining on for a short time If your disk has an optional power supply please use it while the disk is attached to your Router Adding a Printer You can add a printer to your network via your Router s USB port Once connected you can print from various computers and wireless devices within your network Plug your printer s USB cable into the USB port located on the back of your Router You can manually check the status of your printer by visiting the USB Print and Storage Manager found under the Belkin icon displayed in your system tray Windows or menu bar Mac If you have difficulty sharing a printer on your network please see the Troubleshooting section of this manual Note Each computer that will use the printer must have both the Belkin software and the printer s driver installed If the print
5. Increase the distance between the equipment and the receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment 53 IMPORTANT NOTE Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance To maintain compliance with FCC RF exposure compliance requirements please follow operation instructions as documented in this manual This transmitter must not be co located or operating in conjunction with any other antenna or transmitter SAR compliance has been established in typical laptop computer s with USB slots and this product could be used in typical laptop computers with USB slots Other applications such as handheld PCs or similar devices have not been verified and may not comply with related RF exposure rules and such use shall be prohibited The availability of some specific channels and or operational frequency bands is country dependent and firmware is programmed at the factory to match the intended destination The firmware setting is not accessible by the end
6. on the back of your Router Your Router will begin to make your content available to other devices on your network automatically tone wane If you want to configure Media Server by myTwonky visit ee ee http router and choose Media Server There are several settings in the configuration page DLNA Server Enables or disables your media server Server Name The name under which other devices will see your content Refresh Re scans your USB storage devices for media content Shared Drives Shows information about and status of each of your attached drives You can see the name of the drive its capacity and whether media is being served from it or not When you click Save your Router will save your changes 27 belkin 303 the buta Filtering Options IQ Wn rmi Website Filters Powered by Norton Web filters provide a first layer of whole home Internet protection to guard you from unsafe and inappropriate websites on any device on your network There are four different filtering options 1 Block malicious adult and other non family friendly sites 2 Block malicious and adult sites 3 Block malicious sites 4 No filters If you think a site should be added to the filtering list submit a request at safeweb norton com Content filtering may not work as intended if 1 You are connecting through a VPN router 2 You are routing traffic through a proxy se
7. Dynamic Connection Cable and fiber customers generally require a dynamic connection Some DSL customers require a PPPoE connection Let s try dynamic first Select Dynamic from the menu that appears and press Next me us eee 16 GETTING STARTED A host name is generally not required Hit Save The Router will restart ES 2 If after a few minutes your Internet Status says Online you re done You can surf the Internet If these steps do not work try restarting your modem and repeating the process If not we ll try a PPPoE connection next Ine belkin 17 me eo PPPoE Connection Some DSL customers require a PPPoE connection Select PPPoE this time and press Next 18 GETTING STARTED LE Enter the username and password supplied by your Internet provider and click Save Ignore the other fields unless required by your ISP The Router will restart belkin 276 ED belkin A little more oomph LLL J LI SJ e LA m Cem Dm LLLI d vo st If after a few minutes your Internet Status says Connected you re done You can surf the Internet If these steps do not work try restarting your modem and repeating the process 19 Connect Your Wireless Devices Android ios 4 phones and tablets 1 Open the Settings app and select Wireless and Network iPhone iPad and iPod touch 1 Op
8. ate cee Retrieve the network ID card from the foot of your new Belkin Router Neuen bean em Pd din we a Can t find the card The default network name and When requested please enter the password password are also printed on the foot of the Router security key provided on the card Use your computer tablet or smartphone to connect to When your device has connected to the Router use a browser the wireless network shown on the network ID card to visit http router The router homepage will appear For information on how to connect your wireless devices please see the Connect Your Wireless Devices section on page 20 Let s connect to the Internet If the page does not load then try visiting http 192 168 2 1 to see the router homepage Click the Detect my connection button in green If you would rather set up the Router manually click the set it up manually link and proceed to page 10 After several moments your Router should automatically detect your Internet connection and restart This can take anywhere from 30 seconds to 3 minutes depending on your connection type If your Router is unable to establish an Internet connection on its own you may be asked to restart your modem or provide a username and password if your connection requires one Follow the on screen instructions provided Checking for updates j Once your Router is online it will determine if there is a fir
9. complete each of the required fields and click Complete Registration If you don t want to register right now click Register Later to proceed At the next screen you can download optional software that was bundled with your Router 12 mn Get the most out of your router g Belkin Wi Fi 79 Ei Bekin MediaPtay Belkin USB Print and Storage Center b Device Manual o o de po ae This screen shows you optional software that is available for your Router such as the USB software to allow you to print through the Router s USB port If you wish to download and install any of these software programs simply click on the button appropriate for your device When finished installing optional software click Thanks take me to the dashboard 13 Congratulations You are now at your Router s dashboard Your Router is now set up and ready to use The status of your Internet connection is shown in the upper left corner of the Router s homepage If it does not say Online troubleshooting information will be displayed belkin 276 A little more oomph ELM v mees am ig 2 Commer tee Dm eet hote belkin is ELI SC 14 Manually Configuring Your Router s Internet from the Dashboard To set up your ISP connection manually select ISP Connection Type from the list under the header WAN Settings 15
10. having difficulty maintaining a VPN connection Wireless technology is radio based which means connectivity and the throughput performance between devices decreases when the distance between devices increases Other factors that will cause signal degradation metal is generally the worst culprit are obstructions such as walls and metal appliances Note also that connection speed may decrease as you move farther away from the Router In order to determine if wireless issues are related to range we suggest temporarily moving the computer within 10 feet from the Router if possible Changing the wireless channel Depending on local wireless traffic and interference switching the wireless channel of your network can improve performance and reliability See the section titled Changing the Wireless Channel for instructions on how to choose other channels 44 Limiting the wireless transmit rate Limiting the wireless transmit rate can help improve range and connection stability Most wireless cards have the ability to limit the transmission rate To change this property in Windows go to the Windows Control Panel open Network Connections and double click on your wireless card s connection In the properties dialog select the Configure button on the General tab then choose the Advanced tab and select the rate property Wireless client cards are usually set to automatically adjust the wireless transm
11. not be set to auto connect Open the USB Print and Storage Center Check that the printer appears in the list of available devices View the properties of the printer and check that auto connect is selected A different sort of USB device that plugged into the USB port is not showing up on my computer Most USB devices other than disks and printers must be accessed via the USB Print and Storage Center 1 Try unplugging and re plugging the device Please check that the USB connector is firmly plugged into the Router 2 Open the USB Print and Storage Center Check that the device appears in the list of available devices 3 Select the device and click the Use button The device will be virtually connected to your computer until you choose to Stop Using the device or another person requests use of the device 48 Technical Support US http www belkin com support UK http www belkin com uk support Australia http www belkin com au support New Zealand http www belkin com au support Singapore 1800 622 1130 Europe http www belkin com uk support 49 Belkin International Inc Limited 2 Year Product Warranty What this warranty covers Belkin International Inc Belkin warrants to the original purchaser of this Belkin product that the product shall be free of defects in design assembly material or workmanship What the period of coverage is Belkin warrants the Bel
12. operation in the band 5150 5250 MHz is only for indoor use to reduce the potential for harmful interference to co channel mobile satellite systems ii high power radars are allocated as primary users i e priority users of the bands 5250 5350 MHz and 5650 5850 MHz and that these radars could cause interference and or damage to LE LAN devices 55 Avertissement i les dispositifs fonctionnant dans la bande 5 150 5 250 MHz sont r serv s uniquement pour une utilisation l int rieur afin de r duire les risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux ii De plus les utilisateurs devraient aussi tre avis s que les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux c d qu ils ont la priorit pour les bandes 5 250 5 350 MHz et 5 650 5 850 MHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL This radio transmitter IC 3623A F9K1118V2 Model F9K1118V2 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater than the maximum gain indicated for that type are strictly prohibited for use with this device Ce dispositif a t con u pour fonctionner avec une antenne ayant un gain maximal de PCB dipole anten
13. settings by using the Reset button Use the restore option in instances where you may have forgotten your custom password Resetting the Router Push and release the Reset button The lights on the Router will momentarily flash The Router light will begin to blink When the Router light becomes solid again the reset is complete Restoring Your Router to Factory Defaults Press and hold the Reset button for at least 5 seconds and then release it The lights on the Router will momentarily flash The Router light will begin to blink When the Router light becomes solid again the restore is complete 41 Restoring the Router to Default Settings Using the Web Interface Symptoms You need to restore the factory defaults using the web interface E m This may be because the Router is not performing as expected or you wish remove all previously configured settings Setup steps 1 Open a web browser on the computer 3 Click on Restore Factory Defaults in the left hand column under 2 In the address bar of the web browser type heading http router or http 192 168 2 1 42 USING YOUR ROUTER er te Dr qe Rowe rn renters termy normama 4 Click on the Restore Defaults button Message from webpage WARNING Al Your Settings Wil be Lost Aro You Sure You want to do thes 5 warning box will open that s
14. MB RAM 50MB of free hard drive space for installation 36 USING YOUR ROUTER Auto Update on Your Belkin Router The Router will automatically check for a newer version of firmware every time you log into the dashboard and alert you with a message at the top of the screen if there is an update available You can choose to download the new version or ignore it You will see a series of prompts warning you that the firmware is about to be updated Please do not disconnect the power from the Router at this time as it could cause the system to fail 37 USING YOUR ROUTER Updating the Router s Firmware via the Web Interface The following steps show you how to update your Router s firmware using its web interface You do not need to be connected to the Internet as this interface is built into the Router itself Setup steps 1 Locate and download the firmware file from the Belkin support site Type your part number into the search box in the top right corner and look for Firmware in the title 2 Save the file to a location on your computer where you can get to it easily such as your desktop 3 Connect the computer to one of the four LAN ports on the Router refer to image 4 Open a web browser on the computer 5 In the address bar of the web browser type http router or http 192 168 2 1 and press Enter on your keyboard 38 USING YOUR ROUTER Advanced kenga
15. N Connector Connect your modem to this port using an Ethernet cable B Wired LAN Connectors Connect computers and other wired network devices to these ports using Ethernet cables C USB Port USB printers disks and other USB devices plugged into this port will be shared on your network Each USB port has a light that indicates its status Off No USB device is connected or the attached USB device is not in use Blinking Please wait to unplug the device until the light turns off On The USB device is connected and being shared on your network D Reset Button This button is used to restart your Router in rare cases when it functions incorrectly Resetting the Router will preserve your settings This button may also be used to restore the factory default settings Please see the Troubleshooting section for more information E Power Connector Connect the included power supply to this jack TECHNICAL DETAILS Technical Features Integrated 802 11ac Wireless Access Point Utilizing Dual Band Network technology your Router creates two separate networks one at 2 4GHz band and the other at 5GHz band allowing increased bandwidth to all your connected wireless devices and computers NAT IP Address Sharing To save you the cost of adding IP addresses per computer in your house your Belkin Router uses Network Address Translation NAT technology allowing you to share a single IP address acr
16. RED BY LAW IMPLIED INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND SUCH IMPLIED WARRANTIES IF ANY ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL SPECIAL DIRECT INDIRECT CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS BUT NOT LIMITED TO LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Some states do not allow the exclusion or limitation of incidental consequential or other damages so the above limitations may not apply to you 52 REGULATORY INFORMATION FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We Belkin International Inc of 12045 E Waterfront Drive Playa Vista CA 90094 declare under our sole responsibility that the device F9K1118 V2 complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution Exposure to Radio Freque
17. Select WPA WPA2 from the drop down menu under the Authentication heading 4 Enter a password This can be from 8 63 characters of your choice including spaces and punctuation OR a 64 digit hexadecimal number using only the numbers 0 9 and letters A F 5 Click Save to finish Your wireless connection is now encrypted Each computer using your wireless network will need to use the new key Note If you are configuring the Router over a wireless connection you will have to re connect to the Router after changing any security settings Note Some older networking hardware supports only WEP encryption If your older computers cannot connect to your network try 128 bit or 64 bit WEP or seek software updates from their manufacturers 46 I am having difficulty setting up Wired Equivalent Privacy WEP security on my Router 1 Log in to your Router Visit http router or http 192 168 2 1 with your web browser Click Security under the WiFi heading You should now be on the Security page Under Security Mode select the 128 bit WEP option You may type in a WEP key manually or generate one from a passphrase Type a phrase in the Passphrase field and click the Generate button A WEP key is composed of 26 hexadecimal digits 0 9 A F For example C3 03 OF AF 4B B2 C3 D4 4B C3 D4 EE 74 is a valid 128 bit WEP key Click Save to finish Your wireless activity is now encry
18. ake the following steps 1 Contact Belkin International Inc at 12045 E Waterfront Drive Playa Vista CA 90094 Attn Customer Service within 15 days of the Occurrence Be prepared to provide the following information a The part number of the Belkin product b Where you purchased the product c When you purchased the product d Copy of original receipt 2 Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim Belkin reserves the right to review the damaged Belkin product All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser If Belkin determines in its sole discretion that it is impractical to ship the damaged equipment to Belkin Belkin may designate in its sole discretion an equipment repair facility to inspect and estimate the cost to repair such equipment The cost if any of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser Damaged equipment must remain available for inspection until the claim is finalized Whenever claims are settled Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have 51 How state law relates to the warranty THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN THERE ARE NO OTHER WARRANTIES EXPRESSED OR EXCEPT AS REQUI
19. ays Warning All your settings will be lost Are you sure you want to do this Click OK 6 The Router will begin the restoring process Once the restore is complete the Router will reboot Note This may take several minutes Your Router has successfully been restored to its factory settings 43 TROUBLESHOOTING SUPPORT AND WARRANTY Troubleshooting can t connect to the Internet wirelessly If the light on the front of the Router is solid blue then your Router is connected to the Internet You may not be connected to the Router s wireless network Please refer to Connect Your Wireless Devices on page 20 of this manual for instructions If your Windows XP computer is running SP2 you will not be able to set up the Router via the wireless setup process You will need to either update to Windows XP SP3 or complete the setup via a wired connection can t connect to the Internet wirelessly and my network name is not listed in Available Networks 1 Verify that your Router is on and the front panel light shows solid blue 2 If you are far from the Router you might try moving closer to see if you might have been out of range 3 Using a computer attached to the Router via a network cable visit http router and ensure that Broadcast SSID is ON This setting is found on the Channel and SSID page My wireless network performance is slow inconsistent suffers from weak signal or I m
20. driver is not installed you will be asked to install it by the Belkin USB Print and Storage Manager 23 Adding Other USB Devices Other USB devices may also be shared via your Router Plug your device into the USB port located on the back of your Router Computers running the Belkin USB Print and Storage Manager will be able to make use of the shared device 24 Optional Software USB Print and Storage Center The USB Print and Storage Center helps to manage and monitor the use of your USB printers scanners hard drives and other devices that are connected to your Router s USB port and shared across your network 25 Guest Access You can allow guests to use your Internet connection without joining your personal network The network name and password for the guest network is located on the network information card found under the foot of your Router A person using your guest network will be able to join without a password but will be shown a login page when they attempt to surf the Web They will need to enter the guest password into this page to continue 26 Media Server by myTwonky belkin 303 amp Belkin Media Server by myTwonky lets your Router stream music movies and photos to different DLNA UPnP devices on your network In order to use Media Server by myTwonky you will need to insert a USB storage device with media content into a free USB port DLNA Server my TWONKY
21. egistered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Android and Google Chrome are trademarks of Google Inc
22. en the Settings app and select the Wi Fi menu item 2 From there select Wi Fi to see the list of available networks 3 Select your wireless network from the list If asked 2 Select your wireless network from the list that appears to do so enter your network password there If asked to do so enter the network password Mac OS X Your Mac provides a menu of available wireless networks at the right end of the menu bar 1 Click on the 772 icon showing wireless waves 2 Select your wireless network from the list that appears there If asked to do so enter the network password 20 Windows 7 amp Your computer provides a menu of available wireless networks at the right end of the task bar 1 Left click on the gil icon that looks like signal strength bars 2 Select your wireless network from the list If asked enter your network password network key Windows Vista and Windows XP Your device provides a menu of available wireless networks at the right end of the task bar 1 Right click on the icon that shows a computer with wireless waves XP 5 or two computers Windows Vista CH x 2 Choose View Available Wireless Networks XP or Connect to a network Vista from the menu 3 Select your wireless network from the list If asked enter your network password network key 21 ADDITIONAL CAPABILITIES Adding USB Devices 22 Adding a Drive
23. h Canadian ICES 003 Cet appareil numerique de la classe B conforme a la norme NMB 003 du Canada Industry Canada Statement This device complies with RSS standards of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Ce dispositif est conforme a la norme CNR standards d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage prejudiciable et 2 ce dispositif doit accepter tout brouillage recu y compris un brouillage susceptible de provoquer un fonctionnement indesirable susceptible de provoquer un fonctionnement indesirable IMPORTANT NOTE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body D claration d exposition aux radiations Cet quipement est conforme aux limites d exposition aux rayonnements IC tablies pour un environnement non contr l Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps Caution i the device for
24. it rate for you but doing so can cause periodic disconnects when the wireless signal is too weak as a rule slower transmission rates are more stable Experiment with different connection rates until you find the best one for your environment Note that all available transmission rates should be acceptable for browsing the Internet For more assistance see your wireless card s user manual I ve installed this new Router and some of my network clients computers game consoles etc are now unable to connect Your new Router came pre configured with a network name and password found printed on an attached card All clients must use this network name and password to connect wirelessly to your Router You will need to find the network settings on your client select the network name printed on the card from the list of available networks and enter the password when prompted to join the wireless network 45 Does the Router support Wireless Protected Access WPA security The Router ships with WPA WPA2 security turned on Windows XP and some older network hardware may require a software update to support WPA WPA2 I am having difficulty setting up WPA security on my Router 1 Log in to your Router by visiting http router or http 192 168 2 1 with your web browser Click Security under the WiFi heading You should now be on the Security page 2 Under Security Mode select WPA WPA2 Personal PSK 3
25. kin product for two years What will we do to correct problems Product Warranty Belkin will repair or replace at its option any defective product free of charge except for shipping charges for the product Belkin reserves the right to discontinue any of its products without notice and disclaims any limited warranty to repair or replace any such discontinued products In the event that Belkin is unable to repair or replace the product for example because it has been discontinued Belkin will offer either a refund or a credit toward the purchase of another product from Belkin com in an amount equal to the purchase price of the product as evidenced on the original purchase receipt as discounted by its natural use What is not covered by this warranty All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkin s request at the sole expense of the purchaser or if Belkin determines that the Belkin product has been improperly installed altered in any way or tampered with The Belkin Product Warranty does not protect against acts of God such as flood lightning earthquake war vandalism theft normal use wear and tear erosion depletion obsolescence abuse damage due to low voltage disturbances i e brownouts or sags non authorized program or system equipment modification or alteration 50 How to get service To get service for your Belkin product you must t
26. mware update available and offer to install it Please allow up to 5 minutes for the firmware to update Downloading new firmware If there are no updates available then setup will proceed belkin Get everything connected er ee quicker At the next screen you will be invited to change your network name and password Re using your previous network name SSID and password makes connecting your existing devices to the new router much easier If you decide to change these settings then enter the new values and click Save and Continue Note The password must be at least 8 characters long If you changed your network name and password make note of iton the service card located on the foot of the Router You will then have to connect to the new network GETTING STARTED 2 camere T belkin Here is your new network ikam Vat name and password are m Pons Bent Pin Please take this opportunity to register your Router This will help technical support if there is a problem with your Router p e mn ras Let s register your router te Simply complete each of the required fields and click Complete Registration If you don t want to register right now click Register Later to proceed 9 Get the most out of your router E Botkin wi fi EE Cs Ei Beixin MediaPtay Hm cm Belkin USB Print and Storage Center At the next screen you can d
27. ncy Radiation The radiated output power of this device is far below the FCC radio frequency exposure limits Nevertheless the device shall be used in such a manner that the potential for human contact during normal operation is minimized When connecting an external antenna to the device the antenna shall be placed in sucha manner to minimize the potential for human contact during normal operation In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20cm 8 inches during normal operation Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures Reorient or relocate the receiving antenna
28. ne avec dB 3 1 Une antenne gain plus lev est strictement interdite par les r glements d Industrie Canada L imp dance d antenne requise est de 50 ohms Conform ment la r glementation d Industrie Canada le pr sent metteur radio peutfonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pourl metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que lapuissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit n cessaire l tablissement d une communication satisfaisante Le pr sent metteur radio IC 3623A F9K1118V2 Model F9K1118V2 a t approuv par Industrie Canada pour fonctionner avec les types d antenne num r s ci dessous et ayant un gain admissible maximal et l imp dance requise pour chaque type d antenne Les types d antenne non inclus dans cette liste ou dont le gain est sup rieur au gain maximal indiqu sont strictement interdits pour l exploitation de l metteur 56 belkin com 2013 Belkin International Inc All rights reserved All trade names are registered trademarks of respective manufacturers listed iPad iPhone iPod touch Mac Mac OS and Safari are trademarks of Apple Inc registered in the U S and other countries Windows Windows Vista Internet Explorer and DirectX are either r
29. oss your network SPI Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common attacks and viruses Universal Plug and Play UPnP Compatibility UPnP offers seamless operation of voice and video messaging games and other applications that are UPnP compliant Web Based Advanced User Interface You can easily make changes to your Router s advanced settings through your web browser These changes can be made from any computer on your network Integrated 4 Port 10 100 Switch Your Router has a built in 4 port network switch to allow your wired computers to share printers data MP3 files digital photos and much more USB Port The USB port lets you plug in printers hard drives and other USB devices to share across your network 35 System Requirements Router Broadband Internet connection such as a cable or DSL modem with RJ45 Ethernet connection At least one computer with an installed network interface adapter TCP IP networking protocol installed on each computer RJ45 Ethernet networking cable Internet browser Setup A computer running Internet Explorer 8 or higher Firefox Google Chrome or Safari Minimum 1GHz processor and 512MB RAM Or a smart device running iOS or Android operating systems USB Print and Storage Manager Windows XP SP3 or higher Windows Vista or Windows 7 or Mac OS X v10 5 or above Minimum 1GHz processor and 512
30. ownload optional software that was bundled with your Router This screen shows you optional software that is available for your Router such as the USB software to allow you to print through the Router s USB port If you wish to download and install any of these software programs simply click on the button appropriate for your device belkin 276 belkin A little more oomph v I gt 2 m ner Do 00 eem hcm v When finished installing optional software click Thanks take me to the dashboard Congratulations You are now at your Router s dashboard Your Router is set up and ready to use Using the WPS Button 1 Start WPS Push Button Connection WPS PBC on your computer or other Wi Fi device that you would like to connect wirelessly to your Router Often there will be a button for this purpose in software that came with the device or a physical WPS PBC or Security button on the device itself N Within two minutes press the WPS button on your Router and hold for two seconds The WPS light small light above WPS button will blink blue while it listens for your Wi Fi device Once a connection is established the light will turn blue and then go out If a connection is not established the light will blink amber You may repeat the process to try again You can repeat this process for each WPS enabled device you d like to add to your network Manually Set Up Your Internet Connec
31. pted Each computer using your wireless network will need to use the new key Note If you are configuring the Router over a wireless connection you will have to re connect to the Router after changing any security settings Note Some older networking hardware supports only 64 bit WEP encryption If your older computers cannot connect to your network try 64 bit WEP A disk I plugged into the USB port is not showing up on my computer 1 Try unplugging and re plugging the disk Please check that the USB connector is firmly plugged into the Router 2 If your disk has an optional power supply please use it while the disk is attached to your Router 3 The Router supports FAT16 FAT32 or NTFS formatted disks Disks in other formats will not appear in the Finder Mac OS X or Windows Internet Explorer A disk I plugged into the USB port is not coming on or remains on only for a short time Some drives require more power than the Router s USB port provides If your disk has an optional power supply please use it while the disk is attached to your Router 47 A printer plugged into the USB port is not showing up on my computer 1 Try unplugging and re plugging the printer Please check that the USB connector is firmly plugged into the Router 2 To print to a printer attached to the Router your computer must have that printer s driver installed Please check that the driver is installed 3 The printer may
32. rotocol IP uses a 128 bit address to implement additional features that are not present in current IP addresses od Contact your ISP to inquire about their support for IPv6 Pass Through Devices connected to your Router can talk to each other using native IPv6 packets but information will be sent to all connected devices Pass through is not efficient and is not recommended for consistent use 32 GETTING TO KNOW YOUR ROUTER Front Panel A Router Status Light Your Router s status is shown by the light on the front Off The Router is not plugged into a power source Blinking Blue The Router is starting up Solid Blue The Router is connected to the Internet Blinking Amber The Router can t detect the modem Either the modem is off is not plugged into the Router or is unresponsive B Wi Fi Protected Setup WPS Light and Button The WPS button on the front of your Router can be used to help establish a secure connection between your Router and other WPS enabled Wi Fi devices such as computers To use WPS refer to page 9 The small light near the WPS button shows what is happening while you are using WPS to establish a connection Off Idle Blinking Blue The Router is listening for a WPS enabled computer or other device Solid Blue The Router has made a secure connection with the computer or other device Amber A connection was not created 33 Back Panel A Modem WA
33. rver 3 You have previously visited the site and it has been stored in your cache 4 You manually set the DNS servers on your computer tablet or smartphone 28 belkin 303 belkin o bene Rus Booed Test CNP Ent Intellistream QoS Intellistream prioritizes video and gaming traffic for a better online entertainment experience There are two ways to enable Intellistream Run a Speed Test In order for Intellistream to provide you the best media experience your Router needs to know what your approximate Internet speeds are Click Run a Speed Test and the test will begin belkin 303 Once complete you will see the results belkin d 29 belkin 474 belkin men If your Internet speed is greater than 70Mbps when downloading Intellistream QoS will only improve your uploading experience Refresh This will retest your Internet speed When you click Save your Router will save your changes 30 ADDITIONAL CAPABILITIES Manual set This will let you set your approximate Internet speeds If you do not know your Internet speeds contact your ISP belkin 303 belkin me eee belkin 2bb belkin me teen When you click Save your Router will save your changes Intellistream is now enabled 31 IPv6 Configuration belkin 303 belkin A new version of Internet P
34. tion Use a browser to visit http router You can also try visiting http 192 168 2 1 The Router s Welcome page should appear Click the Set it up manually link Please select the type of connection your ISP provides Refer to page 16 fora description of the connection types belkin What type of connection are you setting up Thy amet ag If the selected connection type requires additional information such as an ISP username and password the system will ask you for it At the next screen you will be invited to change your network name and password Reusing your previous network name SSID and password makes connecting your existing devices to the new router much easier 10 oak belkin Get everything connected T Here is your new network quicker name and password Click Great what s next If you decide to change these settings then enter the new values and click Save and Continue Note The password must be at least 8 characters long If you changed your network name and password make note of it on the service card located on the foot of the Router You will then have to connect to the new network Please refer to page 20 to do this eee 11 te belkin tee Let s register your router Please take this opportunity to register your Router This will help technical support if there is a problem with your Router Simply
35. user Modifications The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin International Inc may void the user s authority to operate the equipment Industry Canada Statement This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause interference and 2 This device must accept any interference including interference that may cause undesired operation of the device IMPORTANT NOTE IC Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance To maintain compliance with IC RF exposure compliance requirements please follow operation instructions as documented in this manual Operations in the 5 15 5 25GHz band are restricted to indoor usage only 54 IMPORTANT NOTICE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 23cm between the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter IC Statement This Class B digital apparatus complies wit
Download Pdf Manuals
Related Search