Premier Mounts PCM-MS2
Contents
1. Us etos atrio aUe detto sri basa 15 16 Spec eO 17 curi 18 Warning Statements PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE DISPLAY IF NOT THE WALL STRUCTURE MUST BE REINFORCED PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH DO NOT USE THIS MOUNT WITH A DISPLAY WEIGHING IN EXCESS OF 160LBS SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT2. Qty 12 Nylon Sleeves Qty 4 5 Flat Washers Metal Qty 6 1 Nylon Spacers Oty 6 1 Nylon Spacers Small Qty 6 Page 5 Installation Manual gt 4 PA PCM MS2 Thread Depth Indicator 1 Insert the thread depth indicator supplied through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it 2 Locate the correct diameter screw for the thread insert Compare your marking to the screws supplied 3 f your selected screw is longer than the marking on the thread depth indicator DO NOT USE this screw 4 screw length must not bypass the marking Select another screw size until you find one that comes closest to your mark without going past Inverted Flat Panel Display WEM a B Marking the E E d Thread Insert iy ET Thread Depth Indicator Figure 1 f screw Marking m 5 A Thread Depth Thread Depth ScreW Marking Indico tor Indicator Figure 2 Figure 3 Installation Manual Page 6 b 4 PCM MS2 PA k Finding the Center of the Plasma Display Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to Failure to do so could result in serious personal injury and possible damage to the flat panel Invert the flat panel place it on a soft flat surface to prev
3. e PREMIER MOUNTS The original holding company INSTALLATION INSTRUCTIONS NORTH AMERICA 3130 East Miraloma Avenue Anaheim CA 92806 USA Other Locations USA and Canada Phone 800 368 9700 Fax 800 832 4888 Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2008 9531 000 501 03 PCM MS2 Universal Flat Panel Mount EUROPE Swallow House Shilton Industrial Estate Shilton Coventry England CV79JY Phone 44 0 2476 614700 Fax 44 0 2476 614710 AUSTRALIA NEW ZEALAND OCEANIA DISTRIBUTOR P O Box 295 Mordialloc Victoria 3195 Australia Phone 039586 6330 WWW premiermounts com au c UL Dus PCM MS2 WN BAN EDO Tm 2 lub W 3 ere C 3 Pinging the Center or The Plasma ____ _ ______ ___ 6_6 6 6 7 tbe Montt ke castes tcc sce teresa gt 8 Se CUMING 10 KAN TS H Ss 11 Markie the Bottom Plate I pao xu RUE 12 the Bottom Wall Plate 13 CUS ile 14 Secure the Plasma to the WalEMQOUHL
4. PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE Indicates that the power plug is to be disconnected roy Contact Premier Mounts with any questions from the power outlet 800 368 9700 Safety precautions must be taken at all times Warning and Caution statements It is recommended that a maximum of 5 8 plaster board be used when mounting to wooden studs Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the flat panel display and or damage to the mounting surface Do not install near heater fireplace direct sunlight air conditioning or any other source of direct heat energy Failure to do so may result in damage to the flat panel display and could increase the risk of fire At least two qualified people should perform the installation procedure Injury and or damage can result from dropping or mishandling the flat panel display Page 2 Installation Manual 4 PCM MS2 PA Parts List This wall mount is shipped with all proper installation hardware and components Make sure that none of A Note these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 Mounting brackets Qty 2 Wall plates Qty 2 Griplates Template Qty 1
5. Qty 8 Thread depth d 5 16 x 3 Lag indicator Qty 1 po bolts Qty 8 5 16 flat Level Qty 1 washers Qty 8 Installation Tools Phillips Head Screw Driver Electronic Stud Finder Socket and Wrench Portable Drill Masonry Bit for Concrete Installation 1 4 Drill Bit for Wood Installations Page 3 Installation Manual Qty 8 Ss 2 5 as 16 M4 x25 Ss SS Ss LA 4 MB x 12 SS ELLAS Qty 8 E M5 x 16 8 20 SSS MS x25 Qty 4 M5 50 NC Qty 4 E A SEM wT 12 Qty8 NI Installation Manual M6 x 20 M8 x 20 X M8 x 25 M8 x 30 M8 x 70 PCM MS2 TAMPA 6 Y TANI 6 TAA 6 HA COty _ e na ELLL SS E amp gt 3 ey M M n IA 4 Page 4 PCM MS2 Nylon spacers and flat washers NOTE The nylon spacers may be stacked to achieve proper spacing 1 4 5 Nylon Spacers 1 Nylon Spacers Large
6. E OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 E Miraloma Ave Anaheim CA 92806 How State Law Applies This warranty gives you specific legal rights and you may also have other rights which vary from state to state Page 18 Installation Manual
7. ark a line on the bottom of the carton template Installation Manual Page 14 b 4 Ce PCM MS2 Marking the Bottom Plate Mounting Points Wall Plate Level Wall Structure Step 1 Place the upper portion of the bottom wall plate to the reference line and mark the four 4 lag bolt mounting points through the wall plate slots on the wall Step 2 Level the wall plate with the reference arrow pointing up to the ceiling Drill Gum Pilot Hole Step 3 Pilot holes are recommended size will depend on the commercially available hardware that will be used Installation Manual Page 14 PCM MS2 Securing the Bottom Wall Plate Level Wall Plate Step 1 Level and secure the plate to the wall with the reference arrow facing up to the ceiling Step 2 Secure the plate using commercially available suitable hardware depending on your installation environment Caution Do not over tighten the mounting hardware Marked Wall Template Wall Plate Step 3 When the bottom wall plate is properly installed to the wall Lay the carton template on top of the wall plate Step 4 Lay the top wall plate on top of the cardboard template and mark the four 4 mounting points Installation Manual Page 14 PCM MS2 Securing the Top Plate Pilot Hole Wall Plate Step 1 Drill four 4 4 pilot holes to the marked Power Source Area Wall Plate Step 2 Level and secure the plate to the wall with the r
8. display to its maximum tilt range remove the two 6 mm ote safety knurl knobs push the flat panel back to it s flat position loosen or remove the two 2 M6 x 30 lateral shift screws and lift the unit of the wall Installation Manual Page 14 c El BOMINES Technical Specifications All measurements are in inches mm 24 00 2 44 609 60 59 55 1800 457 20 16 00 406 40 566 143 93 M 20 50 19 900 450 520 70 50546 114 30 10 500 26670 28 00 119 Installation Manual Page 14 PCM MS2 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION US
9. eference arrow facing up to the ceiling Step 3 Secure the plate using commercially available suitable hardware depending on your installation environment Caution Do not over tighten the mounting hardware A Note Check the mount for proper tightness and security Installation Manual Page 14 PCM MS2 Securing the Plasma to the Wall Mount AT LEAST 2 QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL y WALL PLATE_ Step 1 Raise the flat panel with the mounting brackets secured to the flat panel and insert the top and bottom hooks from each bracket to the rods from the wall plates LATERAL SHIFT _ He ee eee _ _6_ i EE sh Ss iS nn nn sons dm rp r i n r p pn gn g n n r qn jn jn r M6 x 30mm Lateral Shift Screws Step 2 Make any lateral shift adjustment and lock it by tightening the two 2 M6 x 30 mm Phillips screws found on the bottom of the mounting brackets Caution Do not over tighten the M6 screws to the rods Installation Manual Page 14 PCM MS2 M amp xl mm Safety Knobs Step 1 Tilt the flat panel and secure the two 2 M6 x 12 mm safety knobs to each of the mounting brackets M To remove the display from the wall simply extend the
10. ent damage to the flat panel Use a blanket foam etc Failure to do so will result in damaging the flat panel Do not lay the flat panel on the floor without any protection to the glass The flat panel is heavy and fragile At least 2 qualified personnel are strongly recommended for installation of this product Failure to do so could result in serious injury and possible damage to the flat panel Top of Flat Panel Tape Measure Inverted Flat Panel Bottom of Flat Panel Step 1 Once the flat panel is inverted use a measuring tape to find the center of your flat panel measuring from outside to outside of the chassis Marking the Center Inverted of the Flat Panel Flat Panel Step 2 Using a pencil lightly mark the center of your flat panel Page 7 Installation Manual PCM MS2 Positioning the Mounting Brackets If your display has uneven mounting points or recessed mounting points please use the provided spacers Page 5 Caution Nylon Spacers Inverted Flat Panel Center Mark Step 1 Install the nylon spacers to the mounting points on the flat panel A Note If the nylon spacers apply to your flat panel please see Page 5 Left Mounting Bracket Right Mounting Bracket Bottom of Flat Panel Arrows Facing Out Step 2 Lay the left and right mounting brackets stamped arrows facing out Page 8 Installation Manual PCM MS2 Align the Mounting Brackets Inverted Flat Pa
11. nel Step 3 Bottom of Flat Panel Mounting Bracket Center of Viewing Guide MENU uds Step 4 The mounting brackets are designed with a center of viewing guide on the side of them Installation Manual Page 14 b 4 Z PCM MS2 Securing the Mounting Brackets The Griplate have M4 M5 M6 and MS hole patterns to fit the hardware that your flat panel requires EXAMPLE If your plasma uses M8 x 20 Phillip screws use the M8 mounting points Phillips Screwdriver rs DIMPLES FACING UP gt DIMPLES FACING UP Step 1 Pre install two 2 M6 x 30 mm Phillip pan screws to the bottom of the left and right hand side mounting brackets Step 2 Once the mounting brackets are aligned secure the Griplate M to the flat panel A Note The dimples of the top plates have to be facing up and the bottom dimples must be facing down Caution not over tighten the mounting hardware A Note Secure the two 2 M6 x 30 Phillip pan screws to the left and right mounting bracket Installation Manual Page 14 b 4 Ce PCM MS2 b Marking the Wall Center of Vvlewing Port Mark the Wall Wall Structure CENTER OF VIEWING HEIGHT DESIRED Step 1 Align the center viewing port from the carton template to the wall Step 2 Match the center of viewing port to the center of viewing height desired Viewing Port Center of Viewing Line Mark the bottom of the Template Step 3 M
Download Pdf Manuals
Related Search