ONKYO LS-B50 soundbar speaker
Contents
1. Steps 3 and 4 need to be performed on the Bluetooth device 1 2 3 4 Turn the unit on Press The indicator flashes faster and the pairing starts The pairing will end in about 30 seconds and the indicator starts flashing slowly On the Bluetooth device select the unit Onkyo LS B50 to make a connection For details on operation see the instruction manual of the Bluetooth device If the operation does not start as normal within the 33 feet 10 m range get the Bluetooth device closer to the unit and retry the operation If a passcode password passkey or PIN code is requested enter 0000 When the pairing is completed the Q indicator lights Start playback Ifyou reset Bluetooth of this unit or removed the registration of this unit from the Bluetooth device perform pairing see above again To connect any other Bluetooth device press and hold the button of the main unit to start pairing Using TV Remote Controller Preprogrammed functions This unit has been preprogrammed so that it can be operated with your existing TV remote controller The functions that can be operated are volume control and muting ix Ifyou want to use other functions or cannot operate with your TV remote controller you can use the learning function as below to enable the operation The mute state can be turned over each time you press the Mute button on your TV remote con2. Remote Controller The remote controller doesn t work Make sure that the battery is installed with the correct polarity gt P 13 Make sure that the remote controller is not too far away from the soundbar and that there s no obstruction between the remote controller and the soundbar s remote control sensor gt P 13 Make sure that the soundbar is not subjected to direct sunshine or invertertype fluorescent lights Relocate if necessary Playing USB Memory The unit supports USB memory formatted using FAT12 FAT16 and FAT32 file system The unit is compatible with MP3 playback and following audio format is supported MPEG1 Audio Layer3 format with a sampling rate of 32 44 1 or 48 kHz and 32 to 320 kbps bit rate MPEG2 Audio Layer3 format with a sampling rate of 16 22 05 or 24 kHz and 8 to 160 kbps bit rate MPEG2 5 Audio Layer3 format with a sampling rate of 8 11 025 or 12 kHz and 8 to 64 kbps bit rate You can play MP3 files stored on the root folder only MP3 files stored on the other folders cannot be played on this unit The Soundbar supports USB flash drives only Note however that playback may not be possible with some USB flash drives The soundbar contains a microcomputer for signal processing and control functions In very rare situations severe interference noise from an external source or static electricity may cause it to lockup In the unlikely event that this hap
3. 1 Press and hold the fo button on the main unit and the buttons for 10 seconds When reset is complete the three INPUT source indicators flash and the unit automatically enters the standby mode Power The soundbar turns off and after Can t turn on the soundbar restoring the power it turns off again Make sure that the power cord is properly plugged into the wall outlet gt P8 Unplug the power cord from the wall outlet wait 10 seconds or more then plug it in again The soundbar turns off unexpectedly The soundbar will automatically enter standby mode when Auto Standby launches gt P12 Remove the power cord from the wall outlet immediately Make sure that all cables and input sources are properly connected and leave the soundbar with its power cord disconnected for 1 hour After that reconnect the power cord and turn the power on If the soundbar turns off again unplug the power cord and contact your Onkyo dealer 18 The protection circuit has been activated If smoke smell or abnormal noise is produced by the soundbar unplug the power cord from the wall outlet immediately and contact your Onkyo dealer Audio There s no sound or it s very quiet Make sure that all audio connecting plugs are pushed in all the way gt P7 8 Make sure that the input of device is connected properly gt P 7 8 When the Status indicator flashes in white the muting is enabled
4. Mode Allows to comfortably listen news programs e MOVIE Mode Creates powerful 3D sound effect suitable for enjoying movies 12 5 SOUND MODE indicators Lights according to the selected sound mode e MUSIC Lights in the music mode e NEWS Lights in the news mode e MOVIE Lights in the movie mode m Lights when the input signal is Dolby Digital 6 Left channel speaker 7 Status indicator Lights white when the power is on It keeps flashing during mute It flashes just once every time volume is adjusted or the input or sound mode is changed Only when using remote controller It goes off during standby 8 Right channel speaker Using Remote Controller How to Use Remote Controller Remote control sensor Approx 16 ft 5 m How to Replace Remote Controller Batter Positive side Back sid 3 eee Use only a battery of the same type g A CR2025 aaa SOUND MODE 1 1 1 e2 1 1 1 1 1 EE H H a 1 ON STANDBY button Switches the power on standby 2 X Mute button Turns the audio off temporarily Press again to cancel muting e The Status indicator flashes when the audio is muted e Muting will also be canceled when the volume is changed or the power is turned off and on 14 3 INPUT buttons Switches the input source e To play the TV sound Turns the TV on and press the button e To play music from
5. PP Stand 2 Cushion 4 Mounting screws 3 8 10 mm 4 Main unit LB401 1 IR flasher 1 Wall mounting template 1 e Wireless subwoofer SKW B50 1 Power cord Polarized plug 1 Cushion 4 PREPARATION Placement Select an appropriate placement for your environment Place the supplied wireless subwoofer in an appropriate place for your use environment e To enjoy the best sound do not place an object on both sides of the unit Place the supplied wireless subwoofer within the 33 feet 10 m distance Mounting to Wall Refer all servicing to qualified service personnel Accessories to be prepared Wall mounting template 1 Attach the template to the position to mount e Be careful not to make a tape mark on the wall e Stand at a distance and check its position Check if it is horizontal 2 Mark the two screw points with a pen WALL MOUNTING TEMPLATE e Leave 1 25 mm between the soundbar and your TV 3 Remove the template and screw the screws into the wall Use the screws with 3 16 4 mm diameter Keep 5 16 8 5 mm of the screw protruding from the wall surface Do not use the supplied mounting screws for stand x a 3 16 4mm 2 5 16 8 5 mm 4 5 Connect all cables to the soundbar gt See 7 to 8 pages Insert the head of the
6. Press or Volume on the remote controller or the Volume buttons simultaneously on the soundbar to disable the muting gt P 14 Make sure that none of the connecting cables are bent twisted or damaged The base sound cannot be heard The protection circuit in the subwoofer may have tripped due to a rise in temperature Disconnect the power cord from the outlet and reconnect after a while 19 The subwoofer produces no sound Make sure that there is no obstacle or reflection between the soundbar and the subwoofer Make sure that the pairing the soundbar and the subwoofer completes normally At the time of purchase pairing has already been completed If the pairing is required please perform the following operation Buttons of the unit Rear of the subwoofer nonoooooooonons Mm a ny Turn on the soundbar 1 Press while pressing 6 3 seconds The status indicator flashes 30 seconds 2 Press and hold LINK button on the rear of the subwoofer supplied until the LINK indicator lights The LINK indicator flashes faster The LINK indicator lights when the pairing is completed Noise can be heard Do not bind the power cord connection cables and other audio cables with a band An audio cable may be picking up interference Try repositioning your cables Make sure that there is no obstacle or reflection between the soundbar and the subwoofer
7. a USB flash drive Connect the USB flash drive and press the button e To play music from a Bluetooth device Press the button Refer to page 16 for connecting 4 VOLUME buttons Allows to adjust the volume by 1 step in the 0 to 30 range 5 SUBWOOFER button Allows to adjust the subwoofer level by 1 step in the 10 to 10 range while listening to the sound The default setting is 0 6 SOUND MODE button Switches the sound mode of input sound as desired The mode switches in the order of MUSIC gt NEWS MOVIE gt MUSIC each time the button is pressed You can select the mode for each input source TV USB and Bluetooth e MUSIC Mode Gives concert hall like sound effect e NEWS Mode Allows to comfortably listen news programs e MOVIE Mode Creates powerful 3D sound effect suitable for enjoying movies 7 USB operation buttons Allows operation when the input source is USB e button Pressing once returns the audio to the beginning of the file being played Pressing twice continuously returns it to the previous file Then the audio will skip back to the previous file each time the button is pressed e button Pressing during stop starts playback Pressing during playback temporarily stops the audio e button The audio skips to the next file each time the button is pressed 15 Playing via Bluetooth Connection ithin 33 ft 10 m SUBWOOFER SOUND MODE
8. th e button is pressed e Auto Power On function The unit automatically turns on when audio signal is output from the T and then for about 3 seconds When this function is set to on the indicator flashes once It flashes twice when this function is set to off e Auto Standby function The unit automatically enters the standby mode if the status with no o V To switch on off this function press and hold first 6 peration and sound continues 5 minutes To switch on off this function press and hold first B and then for about 3 seconds When this function is set to on the indicator flashes once It flashes twice when this function i s set to off 2 INPUT source indicators e Lights when e Lights when e Lights when he source is TV he source is USB he source is Bluetooth 3 lt VOLUME buttons Allows to adjust the vo e Pressing the front of the main uni ume by 1 step in the 0 to 30 range buttons together will mute audio The status indicator on the will flash Press the VOLUME button again to cancel mute 4 SOUND MODE button Switches the sound mode of input sound as desired The mode switches in the order of MUSIC NEWS MOVIE MUSIC each time the button is pressed You can select the mode for each input source TV USB and Bluetooth e MUSIC Mode Gives concert hall like sound effect e NEWS
9. ONKYO _ lili LS B50 Soundbar System Instruction Manual Thank you for purchasing an Onkyo product Please read this manual thoroughly before making connections and plugging in your new Onkyo product Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new product Please retain this manual for future reference Trademarks and Licensing Manufactured under license from Dolby Laboratories DOLBY Dolby and the double D symbol are trademarks of Dolby DIGITAL Laboratories The Bluetooth word mark and logos are registered o trademarks owned by Bluetooth SIG Inc and any use of such 3 Bluetooth marks by Onkyo is under license Other trademarks and trade names are those of their respective owners AURASPHERE AuraSphere is a trademark of Onkyo Corporation AuraSphere is a listening experience technology developed by Onkyo Corporation and Sonic Emotion ag Enl D1308 1 PACKAGE CONTENTS Make sure you have the following items before use e The number in parenthesis indicates the quantity e In catalogs and on packaging the letter at the end of the product name indicates the color AC adapter 1 Power cord 1 Q Remote controller RC 877S 1 Optical digital audio 3 5 mm stereo mini A lithium ion battery CR2025 is supplied in cable 5 ft 1 5 m 1 plug cable 1 the remote control at the time of purchase Ow
10. en you can use any remote controller using preprogrammed function Learning function You can operate the unit with a TV remote controller by assigning the functions to the buttons of the remote controller Perform the following button operation when the C1 indicator starts flashing direct your TV remote controller to remote control sensor of this unit and press the button to assign on the TV remote controller 3 times When the Learning function is successfully set indicator flashes twice Press button first when pressing and holding the buttons together Learning function Button operation Press simultaneously for 3 seconds ON STANDBY 9 VOLUME w VOLUME 17 Learning function Button operation Press simultaneously for 3 seconds MUTE INPUT gt FO 4 SOUND MODE w gt E Itis recommended to select buttons that do not prevent TV operation when assigning the functions to your remote controller Signal of some types of remote controller may not be received by the unit In that case use the remote controller supplied with the unit Troubleshooting Check the items below if you have any problem Before requesting repair If the unit does not work or accept control try resetting the unit to its factory defaults and check if your problem is solved Perform the following reset procedure
11. onnect the supplied IR flasher to allow the TV remote control signal to pass through Double sided tape for mounting is attached to the supplied IR flasher side Mount to near the remote control signal sensor of TV with the double sided tape USB port Connect a USB flash drive Wireless Subwoofer ooooooooononoonorooononoooonooooo 00 0000000000 0000 npopoo0n0 0000000000 Q 0 oD oD oD vooor fl yeonssnov0n0s00000nn00000 KET Bottom Listening to TV Turn on the TV e For details on operation see the BASIC OPERATION P 11 e The unit can be operated with your existing TV remote controller For details on operation see the Using TV Remote Controller P 17 2 Fae e a kal Te 2 1 Turn the power on 2 Switch the input to TV On the buttons of the unit switches in the order of Z TV gt USB gt O Bluetooth 3 Adjust the volume ONKYO Onkyo Corporation Kitahama Chuo Bldg 2 2 22 Kitahama Chuo ku OSAKA 541 0041 JAPAN http Awww onkyo com The Americas Onkyo U S A Corporation 18 Park Way Upper Saddle River N J 07458 U S A For Dealer Service Order and all other Business Inquiries Tel 201 785 2600 Fax 201 785 2650 http Awww us onkyo com For Product Support Team Only 1 800 229 1687 http Awww us onkyo com Europe Onk
12. pens unplug the power cord from the wall outlet wait at least five seconds and then plug it back in If it doesn t work properly please try resetting gt P 18 Onkyo is not responsible for damages such as CD rental fees due to unsuccessful recordings caused by the unit s malfunction Before you record important data make sure that the material will be recorded correctly
13. screw into the keyhole slot of the soundbar and fix it firmly Please confirm that the head of the screw is at the top of the hole Do not use the supplied stands Keyhole slot Please note When preparing the screws used for wall mounting ask qualified service personnel and give careful consideration to their type material and length so that they can withstand the weight If reinforcement is necessary use reinforcing plates or anchors Onkyo is not responsible for accidents or damage caused by improper installation insufficient wall strength improper screw installation or natural calamity etc 5 Mounting on Low Board or TV Stand Accessories to be prepared Stands Cushion Mounting screws Before placing the soundbar on the boards attach the supplied stands to prevent alling Front side Back side Connections e Connect the TV and this unit using one of the possible connection cables W ANALOG OPTICAL COAXIAL TV AUDIO IN COAXIAL DIGITAL OPTICAL ANALOG COAXIAL jack Connect a separately sold cable to input the sound OPTICAL jack Connect the supplied optical digital audio cable to input audio ANALOG jack Connect the supplied stereo mini plug cable to input audio DC IN os eA 4 IR OUT terminal C
14. troller In such case you can synchronize the mute status of the unit and the TV by pressing and holding the Mute button on your TV remote controller To disable the preprogrammed function press and hold first 6 and then for about 10 seconds When the preprogrammed function is successfully disabled indicator flashes 3 times then any TV remote controller cannot be used to operate the unit When you want to re enable the preprogrammed function perform the same operation When the preprogrammed function is successfully re enabled J indicator flashes once then you can use any remote controller using preprogrammed function To control the preprogrammed functions Varieties of TV remote controllers have been preprogrammed on this unit which may lead to unintended operation from the other remote controller than your TV remote controller In such case press and hold first and then and then press either volume or mute button on your TV remote controller 2 or 3 times to turn on the controlling function When the controlling function is set to on the indicator flashes twice and then the other remote controller cannot be operated Controlling function may not be set to some TV remote controllers To cancel the controlling function press and hold first o and then for about 10 seconds When the controlling function is successfully cancelled LJ indicator flashes once th
15. yo Europe Electronics GmbH Liegnitzerstrasse 6 82194 Groebenzell GERMANY Tel 49 8142 4401 0 Fax 49 8142 4208 213 http Awww eu onkyo com Onkyo Europe Electronics GmbH UK Branch Meridien House Ground floor 69 71 Clarendon Road Watford Hertfordshire WD17 1DS United Kingdom Tel 44 0 8712 00 19 96 Fax 44 0 8712 00 19 95 China Onkyo China Limited Hong Kong Unit 1033 10 F Star House No 3 Salisbury Road Tsim Sha Tsui Kowloon Hong Kong Tel 852 2429 3118 Fax 852 2428 9039 http Awww hk onkyo com Onkyo China PRC Mainland 1301 555 Tower No 555 West NanJing Road Jing an District Shanghai China 200041 Tel 86 21 52131366 Fax 86 21 52130396 http Awww cn onkyo com Asia Oceania Middle East Africa Please contact an Onkyo distributor referring to Onkyo SUPPORT site http www intl onkyo com support The above mentioned information is subject to change without prior notice Visit the Onkyo web site for the latest update SN29401537A C Copyright 2013 Onkyo Corporation Japan All rights reserved BASIC OPERATION Using Main Unit Controls 11 1 2 ON STANDBY button INPUT button Switches the power on To turn the power standby Also switches the input source on Press once To turn the standby Press and hold for 3 seconds The indicators go off To input the source Press once to switch Switches in the order of TV gt USB gt Bluetooth each time
Download Pdf Manuals
Related Search