Home

SYBA SY-PEX50039

1. the power sources 3 Open the computer case Refer to your computer user manual for more details 4 Find an available PCI E slot and remove the slot bracket Save the bracket screw for later use 5 Align the SATAII host controller card horizontally with respect to the PCI slot and insert it into the slot firmly and evenly Take care not to the slot fasten it to the computer case with the bracket screw you have saved 6 Connect SATA II device to the connector of controller card with IDE SATA Cable 7 Close the computer case Make sure to reconnect all the external devices to your computer 5 Driver Installation Driver Locations The drivers can be located in the directories of the Driver CD JMicron JMB363 Driver Windows 98 98SE or Windows ME Step 1 Start Windows 98 98SE or Windows ME Step 2 The Update Device Wizard will appear informing you that it has found a PCI RAID controller Chick Next button Step 3 a Windows 98 98SE user Select Specify a location b Windows ME user Select Specify the location of the driver Advanced and then select Specify a location Step 4 Insert the Device CD in the CDROM driver and click on the Browse button Step 5 At the Browse option 1 Select CDROM drive 2 Select folder JMB36x Step6 The Update Device Wizard will appear informing you that it has found Click the Next button Step7 Follow
2. G501975JM36311 PCI E Serial ATAII Host Controller Card USER MANUAL MM JM363 2IR WARNING Before installing and activating RAID function please make sure you have a complete backup of your existing data from hard drives Manufacturer is not responsible for data loss due to abuse misuse or neglect Should you have and installation problem please contact us for assistance All other company and product names are trademarks or registered trademarks of their respective owners 1 Overview MM 363 2IR is a single chip one lane PCI Express to two port Serial ATA Il and one port PATA Host Controller The MM J363 2IR is designed to provide two port SATA II and one port PATA connectivity The MM J363 2IR supports both AHCI and Legacy IDE controller to increase system feasibility including Native Command Queuing NCQ Hot Plugging ATAPI Device Supporting Port Multiplier with Command based Switching Supporting Programmable Output Swing Control to fit SATA II Gen2i and Gen2m External SATA Connection eSATA It features PCI Express bus and Serial ATA interface to express high performance storage devices 2 Features Compliance a gt Compliant with Serial ATA AHCI Advanced Host Controller Interface Spec Reversion 1 0 gt Compliant with Bus Master Programming interface for IDE ATA Controllers Revision 1 0 Compliant with PCI Express Base Spec Revision 1 0a Compliant with Serial ATA High Speed Serialized AT Attachmen
3. cted to the default SATA controller Make sure the Serial ATAII host controller card is properly installed into your system and there is no SATA device connected to the card Step2 Start the Windows system Step3 Windows System will inform you that it has found a PCI X RAID controller Click the next button to continue Step4 Select search for a suitable driver for your device Recommended and click on the next button Step5 Insert Driver CD into the CDROM drive Select Specify a location and click the Next button to continue JMicron JMB363 Driver x32 folder Setp6 The update Device Driver Wizard will appear informing you that it has found driver Click ok button and then the Next button Step7 Follow the setup instructions to complete installation Select 6 Accessories One User Manual One ATA 133 80 wires 40pin IDE cable One serial ATA cable One PCI E SATA Ii HOST controller card One Driver CD
4. t Spec Revision 1 0a Compliant with Serial ATA II Extensions to Serial ATA 1 0a Revision 1 1 Compliant with Gen2i and Gen2m Serial ATA li Electrical Spec Revision 1 0 Integrated 1 Lane PCI Express PHY and 2 port SATA I PHY Integrated two PLL for both PCI Express bus and SATA II interface Output swing control and Automatic impedance calibration for both PCI Express and SATA II PHY Supports up to 64K Byte external Flash for BIOS expansion Supports a slave SMBus interface follow System Management Bus Specification Revision 1 1 Supports 1 Lane 2 5Gbps PCI Express bus Internal native interface multiplexed to 2 port SATA II and 1 port PATA All registers accessible in unified memory space SATA II PATA Functions Supports 2 port 3 0Gbps SATA II interface Supports two independent SATA II channels separate logic and FIFO Supports Native Command Queue NCQ on SATA II port Supports Hot Plugging like USB on SATA II port Supports SATA II Gen2i and Gen2m External SATA Connection eSATA Supports Port Multiplier with Command based Switching on SATA II port Supports up to UDMA6 transfer mode of PATA Supports up to 4 storage device connection Supports up to RAIDO RAID1 JBOD RAID function 3 Jumper settings JP1 For Test 4 Installing the Ultra SATA II IDE Host controller card into your computer 1 Turn off your computer and all external devices connect to it 2 Disconnect your computer from
5. the instructions to finish up the driver installation Windows NT 2000 XP 2003 lf you are performing a new windows NT 4 0 2000 XP or 2003 installation to a SATA hard drive attached to the Serial ATAII controller card Step1 Please copy all the directories and files in the floppy folder to the root directory of a floppy disk to create a pre install disk for Win2K WinXP Win2003 WinXP 64bits Win2003 64bits For example A amd64 x32 txtsetup ocem If your windows NT 4 0 2000 XP or 2003 installation CD is bootable simply put the CD into the CDROM drive and startup your system to begin installation If your windows NT 4 0 2000 XP or 2003 Installation CD is not bootable you must use the windows NT 4 0 2000 XP or 2003 installation diskette to boot up first before commencing installation Step2 Press F6 for third party SCSI or driver installation at the beginning of the text mode installation Insert the 1 44MB floppy diskette into the floppy drive Press S when setup asks if you want to specify an additional device Step3 Press Enter to continue on with text mode setup Step4 Follow the setup instructions to complete installing windows NT 4 0 2000 XP or 2003 If you are already using a SATA hard drive is still connected to the default SATA controller Make sure the Serial ATAII host controller card as the default bootable drive you must follow these procedures Step1 Make sure the SATA hard drive is still conne

SYBA SY-PEX50039

Contents

Download Pdf Manuals

Related Search

Related Contents