Silverstone ST30SF
Contents
1. SILVERSTONE Designing Inspiration SFX Form Factor SST ST30SF Support standard SFX form factor and ATX via included bracket 300W continuous power output at 50 C operating temperature rated for 24 7 operation 80 PLUS Bronze level efficiency 82 85 efficiency at 20 100 loading Class leading single 12V rail with 22A Intelligent semi fanless operation Silent running 80mm fan with 18dBA minimum Single PCI E 6pin connectors support Active PFC SPECIFICATION SFX Form Factor SST ST30SF 300W Switching Power Supply Active PFC Circuit Full Range Input 1 GENERAL DESCRIPTION AND SCOPE This is the specification of Model SST ST30SF AC line powered switching power supply with active PFC Power Factor Correction circuit meet EN61000 3 2 Also 5Vsb power is less than 0 5Winput at power off mode PS_ON input at high state which is comply with ErP Lot 6 year 2013 requirement The specification below is intended to describe as detailedly as possible the func tions and performance of the subject power supply Any comment or additional requirements to this specification from our customers will be highly appreciated and treated as a new target for us to approach 2 REFERENCE DOCUMENTS The subject power supply will meet the EMI requirements and obtain main safety approvals as following 2 1 EMI REGULATORY FCC FCC Part 15 Subpart B Class B EMC EN55022 2006 Al 2007 Class B CISPR 22 1997 Class B EN 610002. wax o Lama w a zea ota ota Corea 08a aoa aaa orm arn 4 3 HOLD UP TIME Typical load of Table 1 115V 60Hz 17 m sec minimum 230V 50Hz 17 m sec minimum The output voltage will remain within specification in the event that the input power is removed or interrupted for the duration of one cycle of the input frequency The interruption may occur at any point in the AC voltage cycle The power good signal shall remain high during this test 4 4 OUTPUT RISE TIME 10 TO 95 OF FINAL OUTPUT VALUE FULL LOAD 115V rms or 230V rms 3 3Vdc 20ms Maximum 5Vdc 20ms Maximum 12Vdc 20ms Maximum 5Vsb 20ms Maximum 12Vdc 20ms Maximum 4 5 OVER VOLTAGE PROTECTION Voltage Source Protection Point 4 6 OVER CURRENT PROTECTION OUTPUT VOLTAGE Max over current limit SFX Form Factor A 4 7 SHORT CIRCUIT PROTECTION Output short circuit is defined to be a short circuit load of less than 0 1 ohm In the event of an output short circuit condition on 3 3V 5V 12V or 12V output the power supply will shutdown and latch off without damage to the power supply The power supply shall return to normal operation after the short circuit has been removed and the power switch has been turned off for no more than 2 seconds 4 8 POWER SIGNAL POWER GOOD 115 230V FULL LOAD 100 500m sec I I I Ti mE T5 HE 1 l l I es i VAC l l l 1 X i
3. G11219230
4. Red Black COM 2 2 COM Black Back COM 3 3 COM Black Red svoc 4 4 a Yelow SATA connector Signal Pi Black COM 4 Red sw 3 Bak com 2 Cveton av 1 6PIN PCI Express connector O sea me se elos y s s con Bleck SFX Form Factor Caution 1 Please turn off your system and switch to O mode on the power supply before attaching or detaching power connectors 2 All power connectors are keyed to prevent incorrect connections If you cannot connect them easily please double check to ensure the connector s direction and type before attempting to connect again Do not attach the connector by force incorrect connection will damage power supply or devices in your system 3 The converting wire picture 5 10 can only be attached with EPS 8 pin connector to convert into ATX 4 pin connecter Incorrect connection will damage power supply or devices in your system The connectors shown above may differ depending on the model of your power supply Warranty Information Warranty terms amp conditions 1 Product component defects or damages resulted from defective production is covered under warranty Defects or damages with the following conditions will be fixed or replaced under SilverStone Technology s jurisdiction a Usage in accordance with instructions provided in this manual with no misuse overuse or other inappro
5. 3 2 2007 Class D ICES 003 2004 Class B EN 61000 3 3 2008 ANSI C63 4 2003 CISPR 22 2005 A1 2005 Class B ASINZS CISPR 22 2006 Class B AY SFX Form Factor ANB 2 2 SAFETY CB IEC 60950 1 2005 2nd Edition and or EN 60950 1 2006 A 11 2009 UL UL 60951 1 2nd Edition 2007 03 27 TUV EN 60950 1 2006 All 3 INPUT ELECTRICAL SPECIFICATIONS 3 1 AC INPUT Paraneior me Nom Max unt Nominal voltages for test purposes are considered to be within 1 0V of nominal 3 2 INRUSH CURRENT Maximum inrush current from power on with power on at any point on the AC sine and including but not limited to three line cycles shall be limited to a level below the surge rating of the input line cord AC switch if present bridge rectifier fuse and EMI filter components Repetitive ON OFF cycling of the AC input voltage should not damage the power supply or cause the input fuse to blow 3 3 INPUT LINE CURRENT amp POWER FACTOR P F At Full load AC input Input line current P F Full Load P F Q Pin 75W 3 4 EFFICIENCY 3 4 1 General Under the load conditions defined in Table 1 and Table 2 The loading condition for testing efficiency shown in Table 1 represents a fully loaded system 50 typical loaded system and 20 light loaded system Table 1 Loading Table for Efficiency Measurements 300W loading shown in Amps Lus oo Table 2 Minimum Efficiency Vs Load Load
6. PS_ON i F 12VDC 5Vpc OPs 3 3VDC J as LI l ITa II x T2 e T Ed n is we PWR OK fi 14 4 i T i LI Figure T1 Power on time shall be less than 500 ms T1 500 ms T2 Rise time 0 1 ms to 20 ms 0 1 ms T2 x20 ms T3 Power ok delay time 100 ms T3 500 ms T4 Power ok rise time T4 S 10 ms T5 T6 AC loss to output hold up time T5 T6 217 ms 4 9 The main power supply shall be off when the PS ON pin is floating open collector The ON STBY pin of P1 must remain off state for 5 Sec maximum prior to switching to the ON state 5 FAN NOISE REQUIREMENTS 5 1 The subject power supply is cooled by a self contained 80mmx15mm 12VDC fan 6 ENVIRONMENTAL REQUIREMENTS The power supply will be compliant with each item in this specification for the following Environmental conditions 6 1 TEMPERATURE RANGE Operating 10 to 50 deg C 20 10 80 deg C 6 2 HUMIDITY Operating 5 95 RH Non condensing 6 3 VIBRATION The subject power supply will withstand the following imposed conditions without experiencing non recoverable failure or deviation from specified output characteristics Vibration Operating Sine wave excited 0 25 G maximum acceleration 10 250 Hz swept at one octave min Fifteen minute dwell at all resonant points where resonance is defined as those exciting frequencies at which the device under test experiences excursions two times large than non res
7. ing Voltage Fullload Typicalload Light load Required Minimum Efficiency 115V Required Minimum Efficiency Minimum Efficiency for test purposes are considered to be within 1 0 of nominal 3 4 2 Standby Power Consumption 5Vsb Input Power 0 5W 5Vsb 45mA amp 230Vac input PS ON input signal Q High State SFX Form Factor FS 4 OUTPUT ELECTRICAL REQUIREMENTS 4 1 OUTPUT VOLTAGE AND CURRENT RATING MINIMUM NORMAL MAXIMUM PEAK LOAD LINE Output RIPPLE amp NOISE LOAD LOAD LOAD LOAD REG REG pma o qoem omer om om pom e cseR atal oem pes e em oem onmes ow oe ee oce 1 3 3V amp 5V total output not exceed 103W 2 Total output continuous shall not exceed 300W watts 3 5Vsb peak current is 3A less then 500m sec minimum voltage during peak is gt 4 5Vdc 4 JVoltages and ripple are measured at the load side of mating connectors with a 0 1 uF monolithic ceramic capacitor paralleled by a 10 uF electrolytic capacitor across the measuring terminals SA gt m _ Am 4 2 LOAD CAPACITY SPECIFICATIONS The cross regulation defined as follows the voltage regulation limits DC include DC Output ripple amp noise Lue sw ww sw o oem peat xT x 25A rena su im pau o o comino 16a 02A 08A OSA oA _ ed aln lx A l a condition 5 a HE ONE HE M condition 6 osa 204 157A osa 1A _condition_7 18A 2A 2A oa 04A eme ma puma rx
8. onant excursions Plane of vibration to be along three mutually perpendicular axes 07 ee SFX Form Factor A 6 4 GROUND LEAKAGE CURRENT The power supply ground leakage current shall be less than 3 5 mA 6 5 RELIABILITY The power supply reliability when calculated by MIL HDBK 21 7 latest revision are exceed 100 000 hours with all output at Typical load and an ambient temperature of 25 C 6 6 DIELECTRIC STRENGTH Primary to Frame Ground 1800 Vac for 1 sec Primary to Secondary 1800Vac for 1 sec 6 7 INSULATION RESISTANCE Primary to Frame Ground 20 Meg ohms Minimum Primary to Secondary 20 Meg ohms Minimum 7 MECHANICAL REQUIREMENTS 7 1 Physical Dimension 125 mm W x 63 5 mm H x 100mm D 7 2 Connectors M B 24PIN connector Signal Pin Pin Signal Green PsoN 16 4 5voc Red Black com 18 6 svoc Red White we 20 8 PWRGOOD Grey Red svoc 21 9 5vsb Purple Red swoc 22 10 12V Yelow Red svoc 23 t1 12v_ Yelow EPS 12V 8PIN connector Soma Pin Pin sga Yellow 2v 6 2 com Black Lo Yellow 12V 8 4 com Black ATX 12V 4PIN 4 4PIN EPS 12V in split mode signal n Spa Bax GNb 1 3 zv Yw 4PIN peripheral connector HDD 4PIN floppy connector FDD RUE a TA EIA AC UAR Yellow nv 1 1 5voc_
9. priate actions b Damage not caused by natural disaster thunder fire earthquake flood salt wind insect animals etc c Product is not disassembled modified or fixed Components not disassembled or replaced d Warranty mark stickers are not removed or broken Loss or damages resulted from conditions other than ones listed above are not covered under warranty 2 Under warranty SilverStone Technology s maximum liability is limited to the current market value for the product depreciated value excluding shipping handling and other fees SilverStone Technology is not responsible for other damages or loss associated with the use of product 3 Under warranty SilverStone Technology is obligated to repair or replace its defective products Under no circumstances will SilverStone Technology be liable for damages in connection with the sale purchase or use including but not limited to loss of data loss of business loss of profits loss of use of the product or incidental or consequential damage whether or not foreseeable and whether or not based on breach of warranty contract or negligence even if SilverStone Technology has been advised of the possibility of such damages 4 Warranty covers only the original purchaser through authorized SilverStone distributors and resellers and is not transferable to a second hand purchaser 5 You must provide sales receipt or invoice with clear indication of purchase date to determine warranty eligibility 6 If a
10. problem develops during the warranty period please contact your retailer reseller SilverStone authorized distributors or SilverStone http www silverstonetek com Please note that i You must provide proof of original purchase of the product by a dated itemized receipt ii You shall bear the cost of shipping or otherwise transporting the product to SilverStone authorized distributors SilverStone authorized distributors will bear the cost of shipping or otherwise transporting the product back to you after completing the warranty service iii Before you send the product you must be issued a Return Merchandise Authorization RMA number from SilverStone Updated warranty information will be posted on SilverStone s official website Please visit http www silverstonetek com for the latest updates Additional info amp contacts For North America usasupport silverstonetek com SilverStone Technology in North America may repair or replace defective product with refurbished product that is not new but has been functionally tested Replacement product will be warranted for remainder of the warranty period or thirty days whichever is longer All power supplies should be sent back to the place of purchase if it is within 30 days of purchase after 30 days customers need to initiate RMA procedure with SilverStone Technology in USA by first downloading the USA RMA form for end users form from the below link and follow its instructions For Aus
11. tralia only support silverstonetek com Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Please refer to above Warranty terms amp conditions for further warranty details For Europe support eu silverstonetek de For all other regions Support silverstonetek com Warranty length For North America and Australia All SilverStone retail PSU have from the date of purchase 3 years limited warranty some PSU carry a 1 or 5 year warranty For further information please visit http www silverstonetek com For Europe All SilverStone retail PSU have from the date of purchase 3 years limited warranty some PSU carry a 2 or 5 year warranty For further information please visit http www silverstonetek com For all other regions Please contact your local SilverStone authorized dealer or distributors for more information Note SilverStone reserve the right to alter the above warranty information Please visit http www silverstonetek com for the latest update of the warranty information SilverStone Technology Co Ltd www silverstonetek com support silverstonetek com Issue date April 2013 NO
Download Pdf Manuals
Related Search