EnovateIT E997
Contents
1. MANUAL Assembly STEP2 While on a flat surface insert monitor pole stem through plastic washer into riser arm STEP 3 Using a 1 8 allen wrench attach keyboard tray or eDesk to monitor pole stem with 10 24 x 3 4 flat head screws NOTE To avoid stripping the screws or screw holes do not use a power tool for this step Screws should be hand tightened only Only use screws provided in installation kit Plastic Washer Place on Flat Surface 13 MANUAL Assembly Riser Arm Stem STEP 4 NON EXTENSION ARM Insert riser arm stem through plastic washer into pivot mount Plastic Washer and secure with large slotted pan head screw Large Slotted Pan Head Screw Kol STEP 4 2 EXTENSION ARM Insert riser arm stem through plastic washer into extension arm and secure with large slotted pan head screw Riser Arm Stem Plastic Washer Large Slotted Pan Head Screw 14 MANUAL Assembly STEP2 Align screws with the quick mount slots in the monitor pole VESA plate Slide the monitor into place and tighten the screws STEP 3 Insert the additional two M4 x 16mm screws and standof2. STEP2 Push the keyboard tray release tabs to the right and remove the keyboard tray STEP 3 STEP4 Place adhesive pad with cable tie Lay the mouse and keyboard cables into place as shown into place and allow the ends of the cables to hang out of the bottom of the eDesk Cable Tie amp Adhesive Pad 17 MANUAL Cable Management STEP5 Tie cables into place Take care to leave the appropriate amount of slack inthe cables to open and close the keyboard tray properly STEP 6 Keyboard Tray Cable Notch and Cable Management Insert Replace the keyboard tray and place the mouse and keyboard into place STEP7 Run the mouse and keyboard cables thought the keyboard notch and replace the rubber keyboard cable management insert STEP 8 Replace the plastic cover plate 18 MANUAL Cable Management RISER ARM CABLE MANAGEMENT STEP 1 Run video and power cables down monitor pole and riser arm Also run mouse and keyboard cables into riser arm Snap cable covers into place p Mouse Cable Exit Keyboard Cable Exit On Opposit
3. ern xcd L mcum j STEP2 Using 5 16 allen wrench adjust screw clockwise or counterclockwise CLOCKWISE LIGHTER TENSION COUNTERCLOCKWISE STRONGER TENSION 22 MANUAL Adjustments MONITOR POLE TENSION ADJUSTMENT STEP 1 Remove plastic cover lt CET EZ Sa LISTS STEP 2 Using a 1 2 socket wrench adjust nut to tighten or loosen tension CLOCKWISE TIGHTEN TENSION COUNTERCLOCKWISE LOOSEN TENSION 0 gt FOR gt AJ Be Ope 23 MANUAL Adjustments WORK SURFACE AND MONITOR LEVELING J Movement when folded STEP 1 Lower riser arm to access set screws STEP 2 Using a 1 8 allen wrench loosen set screw 1 this will unlock the adjustment pin STEP 3 Using a 4mm allen wrench tighten or loosen set screw 2 to move adjustment pin Re tighten set screw 1 Do not over tighten set screws Movement when extended 24 MANUAL Adjustments KEYBOARD TILT STEP 1 Fold eDesk to stored position STEP 2 Remove plastic cover plate STEP 3 Locate the set screw STEP 4 Using a 1 8 allen wrench turn the set screw clockwise to the desired position 25 Accessorie
4. 2 Socket Wrench ji Phillips Screwdriver WE 1 E s Flat Head Screwdriver The following procedures must be performed as described to ensure proper installation Mounting NOTE Always mount the e997 to a wall stud Wall Stud 48 Walltrack Wall Stud 42 Walltrack 1 Wall Stud N 32 Walltrack Tem 1 Bottom of Track Y X Y Z Mounting Max Keyboard Min Keyboard Height Height Height 2 36 5 45 34 X 32 5 41 30 28 5 37 26 MOUNTING HEIGHT DIAGRAM MANUAL Mounting Preferred Method of Mounting 20 Gage 035 or Heavier Metal Stud STEP 1 Determine Your desired keyboard height Use the chart on previous page for standard keyboard heights adjust vertical dimensions as required for desired keyboard height STEP2 Locate the exact center line of the wall stud where the arm will be mounted STEP 3 Using a level mark the hole locations for the appropriate track size using the dimensions to the left make note of the bottom of the track STEP4 Place the track against the wall and secure with the Wide Flat Washer the Phenolic Washer and the Hex Nut Self Tapping Metal Screw DO NOT DRILL PILOT HOLES STEP5 Ensure tra
5. and slide channel through hole Must be 1 7 8 minimum clearance behind wall for channel rotation Metal Stud STEP 2 3 8 3 5 8 115 Hold ends of straps between bx E thumb and forefinger and pull toward you until channel rests flush behind wall Slide plastic cap mD7 along straps with other hand until flange of cap is flush with wall SS Metal Stud STEP 3 Snap straps at wall by pushing side to side snapping off straps level with flange of cap Patented under one or more of the following U S Patent Nos 4 993 901 5 028 186 5 161 296 5 738 385 6 161 999 7 144 212 7 320 569 and foreign counterparts thereof and of 4 650 386 and 4 752 170 Other patents pending TOGGLER and typeface symbol TA TB TC TH ALLIGATOR SNAPTOGGLE and SnapSkru are worldwide registered trademarks of Mechanical Plastics Corp Assembly STEP 1 NON EXTENSION ARM Slide pivot mount to bottom of wall track you may need to pull the pivot mount towards you while sliding level and secure screws tightly with 3 16 allen wrench STEP 1 2 EXTENSION ARM Slide pivot mount with extension arm to bottom of wall track level and secure screws tightly with 3 16 allen wrench
6. 21999 Articulating Wall Arm Enovate Medical e997 Articulating Wall Arm was designed to set a new standard in quality Enovate Medical s goal is to provide a wall arm that is ready for years of use and backed by a commitment of exemplary service and support Thank you for purchasing the Enovate Medical e997 Articulating Wall Arm MANUAL Warnings o 22 26 27 WELCOME WARNINGS COMPONENTS amp HARDWARE MOUNTING ASSEMBLY CABLE MANAGEMENT ADJUSTMENTS ACCESSORIES MOVEMENT MANUAL e Table of Contents Warnings N Important Warnings Electrical Shock Warning The above symbols represent safety warnings that require significant attention when seen onthe EMC cart or inthe user manual Failure to do so could result in minor injury major injury or even death Read the entire installation manual before you begin MOUNTING Installer must verify that the entire wall will safely support the combined weight of all attached equipment and hardware Improper installation of this product can cause extensive property damage or serious personal injury either during or after installation It is the responsibility of the installer to ensure that all applications including wood concrete block brick steel etc are secured properly and are in compliance with local and national building codes California installations could require specific anchorage and additional mounting scr
7. ck is level before fully tightening screws DO NOT OVER TIGHTEN SCREWS If hole strips out see page 10 1 4 14 x 2 1 2 y Hex Nut Self Tapping Metal Screw 7 Phenolic Washer t Wide Flat Washer REF OSHPD OPA 2671 10 MANUAL Mounting Wood Stud Mounting Hardware not included Follow Steps 1 through 3 from the previous page STEP4 Drill a 3 16 pilot hole into each of the mounting hole locations Use the Wide Flat Washer Phenolic Washer and the Hex Nut Wood Screw to secure the track to the wall STEP5 Ensure track is level before fully tightening screws 1 4 14 x 4 Hex Nut Wood Screw V KOA lt Phenolic Washer i Wide Flat Washer For Striped Holes or Lighter than 20 035 Gage Metal Studs Hardware not included Follow Steps 1 through 3 from the previous page STEP 4 Drill a Y holes through the center of the striped hole and install SNAPTOGGLE brand hollow wall anchors See wall anchor installation instructions on page 11 STEP 5 Ensure track is level before fully tightening with cross drive 1 4 20 x 2 1 2 screws Track Fr Wall Metal Stud N Hi mnm N 10 MANUAL eMounting SNAPTOGGLE METAL STUD ANCHOR INSTALLATION STEP 1 Drill a 72 hole through center of metal stud Hold metal channel flat alongside plastic straps
8. e Side Cable Tie amp Adhesive Pad STEP 2 Run cables along extension arm if applicable and up wall track Snap cable cover into place Cable Tie amp Adhesive Pad Monitor Pole Cable Cover Riser Arm Cable Cover Cable Cover MANUAL 2 Cable Management STEP 3 Install wall track cover place a single side into place then starting at one end flex cover inward until opposite side snaps into place STEP 4 WITHOUT CPU BRACKET Secure top plate with 10 24 x 1 2 button head screws and a 1 8 allen wrench 20 MANUAL Cable Management STEP 4 2 WITH CPU BRACKET Insert CPU bracket into wall track Top of wall track install Bottom of wall track install Remove CPU bracket mount and replace as shown f MS Bee STEP5 Place CPU into CPU Bracket adjust front plate until it securely holds the CPU then tighten knobs CPU 21 Adjustments RISER ARM VERTICAL TENSION ADJUSTMENT Adjustments should be made only after all peripherals are installed STEP 1 Ensure riser arm is parallel to the floor L a
9. ediately to reguest service If the unit is not working properly please contact Enovate Medical Customer Service at enovatemedical com support 888 909 8930 toll free Components amp Hardware STANDARD COMPONENTS Q Wall Track 32 42 48 EK Nu B Wall Track End Cap 2x Wall Track Cable Cover E o Monitor Pole amp Cable Cover Pivot Mount mim Riser Arm 8 Cable Cover o Standard Keyboard Tray Mouse Holder Standard Tray Adhesive Mouse Pad 0 0 Riser Arm Knuckle OPTIONAL COMPONENTS Extension Arm amp Cable Cover CPU Bracket eDesk HARDWARE INCLUDED 6 8 x 1 4 14 x 2 1 2 Plastic Washer Hex Nut Self Tapping Metal Screw for metal stud mounting only 6 8 x 6 8 x 2x 1 4 x 1 1 4 1 10 24 x 3 4 Phenolic Washer Wide Flat Washer Flat Head Screw l 4x 4x 10 24 x 1 2 M4 x 16mm 10 x 1 4 Button Head Screw Pan Head Screw Standoff 5x 4x Cable Tie Dual Lock Pads amp Adhesive Pad TOOLS NEEDED Drill 3 8 Socket Level Pencil Wrench 5 64 1 8 4mm 3 16 5 16 Allen Wrench Allen Wrench Allen Wrench Allen Wrench Allen Wrench 1
10. ews Check with local authorities for codes in your area Other seismic states have similar regulations WARNING Because wall surfaces and construction methods and materials vary it is imperative that you consult with the appropriate engineering architectural or construction professional to ensure that your wall computing station is mounted properly to handle the applied loads ELECTRICAL SHOCK HAZARD Cutting or drilling into electrical wires and cables can cause FIRE DEATH or SERIOUS PERSONAL INJURY Always make certain the area behind the mounting surfaces is free of electrical wires and cables before drilling into wall EXPLOSION AND FIRE HAZARD Drilling into gas plumbing can cause EXPLOSION FIRE DEATH or SERIOUS PERSONAL NJURY Always make certain the area behind the mounting surface is free of gas water waste or any other plumbing before drilling into wall WARNING Weight should not exceed 20lbs gt PPP SERVICE AND REPLACEMENT Warranty will be void if an attempt to service or replace any part of the Enovate Medical Wall Arm is made unless directed to do so through Enovate Medical approved documentation i e this User Manual or other instructions Only Enovate Medical or an Enovate certified entity may service or replace the Enovate Medi cal Wall Arm components If any component on the Enovate Medical Wall Arm is missing or damaged the wall station must not be used Contact Enovate Medical imm
11. fs into the bottom two holes of the monitor pole VESA plate to properly secure the monitor NOTE Use the 4 10 Standoffs if needed Adhesive Mouse Pad Place the adhesive mouse pad into place before mounting the keyboard MOUNTING THE KEYBOARD Mount keyboard to keyboard tray using dual lock pads provided MOUNTING THE MONITOR STEP 1 Loosely insert two M4 x 16mm screws with standoffs into the top two holes of the VESA pattern on the back of the monitor Cable Management and Cable Management Insert Keyboard Tray Cable Notch 2 L Adhesive Mouse Pad STEP 1 Run the mouse and keyboard cables through the keyboard notch letting them hang out ofthe bottom of the keyboard tray HF STEP 2 Replace the rubber cable management insert and plastic cover plate MANUAL Cable Management eDESK CABLE MANAGEMENT STEP 1 Extend keyboard tray
12. s MOUNTING MOUSE HOLDER STANDARD TRAY STEP 1 Peel backing from two sided tape on back of mouse holder STEP 2 Place mouse holder 26 Movement ARM EXTENSION KEYBOARD TILT MONITOR TILT 27 MANUAL Movement amp Adjustment RANGE OF MOVEMENT WITH EXTENSION ARM 90 90 28 MANUAL Movement amp Adjustment RANGE OF MOVEMENT NO EXTENSION 4 NIE X N 90 N S DS 90 29 30 31 32 33 enovate MEDICAL 1152 Park Avenue Murfreesboro TN 37129 p 888 909 8930 f 615 896 8906 www enovatemedical com support enovatemedical com 2013 Enovate Medical LLC All Rights Reserved
Download Pdf Manuals
Related Search