La Crosse Technology WS7027
Contents
1. R amp TTE Directive 1999 5 EC Summary of the Declaration of Conformity We hereby declare that this wireless transmission device does comply with the essential requirements of R amp TTE Directive 1999 5 EC 552. When 12h mode display is selected the calendar format will be month and date display MANUAL TIME SETTING In case the Weather Station is not able to detect the DCF signal disturbances transmitting distance etc the time can be manually set The clock will then work as a normal Quartz clock 43 TIME Hours flashing Q cJ uy Minutes flashing DCF To set the clock 1 The hour and minute digits start flashing in the time display section 2 Use the IN key to adjust the hours and the OUT key to adjust the minutes If you hold the key while you adjust the hours move 1 hour and the minutes move 5 minutes 3 Confirm with the SET key and enter the Calendar Setting or exit the setting mode by pressing the Note The unit will still try and receive the signal despite it being manually set When it does receive the signal it will change the manually set time into the received time During reception attempts the DCF tower icon will flash If reception has been unsuccessful then the DCF tower icon will not appear but reception will still be attempted the following day CALENDAR SETTING DATE DATE Cui me Year flashing Date flashing Month flashing The date default of the Weather station is 1 1 of the year 2006 after initial set up Once the radio controlled time signals are received the date is automatically updated However if the signals are not received the date can also be set manually To do this
3. about 75 due to the varying areas the Weather Station has been designed for use in In areas that experience sudden changes in weather for example from sunny to rain the Weather 46 Station will be more accurate compared to use in areas where the weather is stagnant most of the time for example mostly sunny If the Weather Station is moved to another location significantly higher or lower than its initial standing point for example from the ground floor to the upper floors of a house remove the batteries and re insert them after about 30 seconds By doing this the Weather Station will not mistake the new location as being a possible change in air pressure when really it is due to the slight change of altitude Again disregard weather forecasts for the next 12 to 24 hours as this will allow time for operation at a constant altitude THE WEATHER TENDENCY INDICATOR Working together with the weather icons are the weather tendency indicators located on the left and right hand side of the weather icons When the indicator points upwards it means that the air pressure is increasing and the weather is expected to improve but when indicator points downwards the air pressure is dropping and the weather is expected to become worse Taking this into account one can see how the weather has changed and is expected to change For example if the indicator is pointing downwards together with cloud and sun icons then the last noticeable change in
4. sudden temperature changes this may lead to rapid changes in forecasts and readings and thereby reduce their accuracy SPECIFICATIONS Temperature measuring range Indoor 9 9 C to 59 9 C with 0 1 C resolution 14 2F to 139 8F with 0 2F resolution OF L displayed if outside this range Outdoor 39 9 C to 59 9 C with 0 1 resolu tion 39 8 F to 139 8 F with 0 2 F resolution OF L displayed if outside this range 53 Relative humidity measuring range ndoor humidity range Outdoor humidity range nterior data checking intervals ndoor temperature checking interval ndoor humidity checking interval Outdoor temperature and humidity data checking interval Power consumption Weather station Thermo Hygro outdoor transmitter Battery life Dimensions L x W x H Weather Station Thermo Hygro outdoor transmitter LIABILITY DISCLAIMER 1 to 99 with 1 resolution Display if temperature is OL F display if lt 1 and 99 if gt 99 1 to 99 with 1 resolution Display if outside temperature is OF L display 1 if lt 1 and 99 if gt 99 every 15 seconds every 20 seconds Every 4 seconds or every 15 minutes if data are lost and display 3 x AA IEC LR6 1 5V 2 x AA IEC LR6 1 5V up to 24 months Alkaline batteries recommended 91 x 29 x 144 9mm without stand 38 2 x 21 2 x 128 3 mm without wall bracket The electrical and
5. will sound Following the indoor temperature humidity and the time as 0 00 will be displayed If these information are not displayed on the LCD after 60 seconds remove the batteries and wait for at least 60 seconds before reinserting them Once the indoor data is displayed user may proceed to the next step 3 After the batteries are inserted the Weather station will start receiving data signal from the transmitter The outdoor temperature and humidity data should then be displayed on the Weather station If this does not happen after 2 minutes the batteries will need to be removed from both units and reset from step 1 4 In order to ensure sufficient 868 MHz transmission however the distance between the Weather Station and the transmitter should not be more than 100 meters see notes on Positioning and 868 MHz Reception 34 Note In the event of changing batteries of the units ensure the batteries do not spring free from the contacts Always wait at least 1 minute after removing the batteries before reinserting otherwise start up and transmission problems may occur WHEN MORE THAN ONE TRANSMITTER IS USED 1 User shall remove all the batteries from the Weather Station and transmitters and wait 60 seconds 2 Insert the batteries in the first transmitter 3 Within 2 minutes of powering up the first transmitter insert the batteries in the Weather Station Once the batteries are in place all segments of the LCD will lig
6. WIRELESS 868 MHz WEATHER STATION Instruction Manual INTRODUCTION Congratulations on purchasing this Weather Station with wireless 868MHz transmission of outdoor temperature and humidity and display of indoor temperature and humidity It is further featuring a DCF 77 radio controlled clock with date display With four easy to use function keys this innovative product is ideal for use in the home or office MTs o INSTANT TAANSMISSION Instant Transmission is the up and coming state of the art new wireless transmission technology exclusively designed and developed by LA CROSSE TECHNOLOGY IT offers you an immediate update of all your outdoor data measured from the transmitters follow your climatic variations in real time 30 FEATURES The Weather Station fe Ys RS RS e o o o ee eo eo LCD Display Battery cover Function Keys fl i il o ae Detachable stand DCF 77 Radio controlled time with manual setting options Time reception ON OFF 12 24 hour display Hour and minute display seconds indicated by flashing dot Time zone option 12hours Date and month weekday and date calendar display selectable Weather forecasting with 3 weather icons and weather tendency indicator Weather forecasting icon sensitivity setting Temperature display in degrees Celsius or Fahr enheit F selectable Indoor and o
7. anne HMO Outdoor cls qupoor winwax Ee HOMO E MINMAX me 1m U A aC E 4 Weather Forecast icon cA H HUMIDITY C Outdoor reception signal h T i a emperature in Number showing Transmitter unit Comfort Indicator Icon Indoor Relative Humidity Outdoor Relative Humidity When the signal is successfully received by the Weather Station the outdoor transmission icon will be switched on If not successful the icon will not be shown on LCD The user can then easily see whether the last reception 38 was successful icon on or not icon off On the other hand the short blinking of the icon shows that a reception is currently taking place For better distinctness the LCD screen is split into 5 sections displaying the information for time date weather forecast indoors and outdoors LCDI RADIO CONTROLLED TIME In normal mode display of radio controlled time A reception tower symbol in the upper left hand corner of LCD 1 of the display indicates that the DCF 77 time signal is scanned for flashing or received steady In setting mode display of manual setting values LCD 2 CALENDAR Display date and month In setting mode display of a variety of references and setting values LCD 3 WEATHER FORECAST AND WEATHER ICONS Display of the weather to be expected in form of three weather symbols and two weather tendency indicators in form of an arrow which change th
8. cs Using the IN key set the year required The range runs from 2003 to 2029 default is 2006 2 Press the SET key to enter the month and date setting mode 44 3 Press the IN or OUT key to set the date and the OUT or IN key to set the month required 4 Confirm with the SET key and exit the setting mode by pressing the CH key twice Note Skip the SNOOZE function as it is not available in France s model C F TEMPERATURE DISPLAY SETTING TIME D H Flashing DCF The default temperature reading is set to degre e Celsius To select F degree Fahrenheit i The will be flashing use the IN key to tog gle between and F 2 Once the desired temperature unit has been chosen confirm with the SET key and enter the Weather Forecast Icon Sensitivity setting or exit the setting mode by pressing the CH key WEATHER FORECASTING ICON SENSITIVITY SETTING For locations with rapid changes of weather conditions the threshold can be set to a different level for faster display of weather conditions poe eeN TIME g Digit flashing DCF As Using the IN key to set the weather sensitivity level There are 3 levels of setting 1 2 and 3 level 1 is the most sensitive setting level 3 is the least sensitive setting default setting is 2 2 Confirm with the SET key and exit the Manual settings 45 WEATHER FORECAST AND TENDENCY The weather forecasting icons There are 3 weather icons in the thir
9. d humidity data and the times at which they were recorded press the IN key continuously for about 3 seconds This will reset all minimum and maximum data recorded to the current time date temperature and humidity The min max temperatures and humidity recorded are of current time and they remain unaffected by the time zone setting 48 OUTDOOR TEMPERATURE AND HUMIDITY Maximum Display Outdoor Reception Signal QUTDOOR HUMIDITY Outdoor Temperature in Relative Humidity Number showing Transmitter unit only if there is more than one transmitter The last LCD section shows the outdoor temperature and humidity a reception signal and a number beside the temperature will also show if more than one transmitter has been used TOGGLING AND RESETTING THE OUTDOOR RECORDINGS 1 To toggle between the outdoor current minimum and maximum temperature and humidity data and the times at which they were recorded press the OUT key Once to show the minimum temperature and humidity values with time and date recorded Twice to show the maximum temperature and humidity values with time and date recorded Three times to return to the current time date temperature and humidity levels Note the time date information is only available for MIN MAX temperature data 2 To toggle between transmitters press the CH key Once to show transmitter 2 Twice to show transmitter 3 Three times to return to transmitter 1 Note The transmitter nu
10. d section of LCD which can be displayed in any of the following combinations FORECAST FORECAST FORECAST de Se STi Sunny Cloudy with sunny intervals Rainy For every sudden or significant change in the air pressure the weather icons will update accordingly to represent the change in weather If the icons do not change then it means either the air pressure has not changed or the change has been too slow for the Weather station to register However if the icon displayed is a sun or raining cloud there will be no change of icon if the weather gets any better with sunny icon or worse with rainy icon since the icons are already at their extremes The icons displayed forecasts the weather in terms of getting better or worse and not necessarily sunny or rainy as each icon indicates For example if the current weather is cloudy and the rainy icon is displayed it does not mean that the product is faulty because it is not raining It simply means that the air pressure has dropped and the weather is expected to get worse but not necessarily rainy Note After setting up readings for weather forecasts should be disregarded for the next 12 24 hours This will allow sufficient time for the Weather Station to collect air pressure data at a constant altitude and therefore result ina more accurate forecast Common to weather forecasting absolute accuracy cannot be guaranteed The weather forecasting feature is estimated to have an accuracy level of
11. dity are measured and transmitted every 4 seconds The range of the Thermo Hygro outdoor transmitter may be affected by the temperature At cold temperatures the transmitting distance may be decreased Please bear this in mind when placing the transmitter 868MHz RECEPTION CHECK If the outdoor temperature and humidity data are not being received within three minutes after setting up or outdoor display always show in the outdoor section of the Weather station during normal operation please check the following points 50 1 The distance of the weather station or transmitter should be at least 1 5 to 2 meters away from any interfering sources such as computer monitors or TV sets 2 Avoid positioning the Weather Station onto or in the immediate proximity of metal window frames 3 Using other electrical products such as headphones or speakers operating on the same signal frequency 868MHz may prevent correct signal transmission and reception 4 Neighbours using electrical devices operating on the 868MHz signal frequency can also cause interference Note When the 868Mtz signal is received correctly do not re open the battery cover of either the transmitter or Weather Station as the batteries may spring free from the contacts and force a false reset Should this happen accidentally then reset all units see Setting up above otherwise transmission problems may occur The transmission range is about 100 m from the transmitte
12. e marking 3 Replace compartment cover HOW TO INSTALL AND REPLACE BATTERIES IN THE THERMO HYGRO OUTDOOR The Thermo hygro transmitter uses 2 x AA IEC LR6 1 5V battery To install and replace the batteries please follow the steps below f Remove the battery compartment cover 2 Insert the batteries observing the correct polarity see marking 3 Replace the battery compartment cover on the unit Note In the event of changing batteries in any of the units all units need to be reset by following the setting up procedures This is because a random security code is assigned by the transmitter at start up and this code must be received and stored by the Weather station in the first 3 minutes of power being supplied to it 33 BATTERY CHANGE It is recommended to replace the batteries in all units on an annual basis to ensure optimum accuracy of these units X Please participate in the preservation of the environment Return used batteries to an authorised depot SETTING UP WHEN ONE TRANSMITTER IS USED 1 First insert the batteries in the transmitter see How to install and replace batteries in the Termo hygro outdoor transmitter above 2 Within 2 minutes of powering up the transmitter insert the batteries in the Temperature Station see How to install and replace batteries in the Weather Station above Once the batteries are in place all segments of the LCD will light up briefly and a short signal tone
13. eir appearance depending on the air pressure development ECD 4 INDOOR TEMPERATURE AND HUMIDITY In normal mode on the left display of the current indoor temperature In normal mode on the right display of the current indoor relative humidity By pressing the IN key display of the stored MIN MAX indoor temperature and humidity with simultaneous display of a MIN or MAX symbol in the upper center In normal mode display of comfort indicator 39 Display of low battery indicator A small battery symbol on the upper right side indicates low running batteries Pela OUTDOOR TEMPERATURE AND HUMIDITY In normal mode on the left display of the current outdoor temperature In normal mode on the right display of the current outdoor relative humidity By pressing the OUT key display of the stored MIN MAX outdoor temperature and humidity with simultaneous display of a MIN or MAX symbol in the upper center By pressing the CH key display of outdoor sensors up to three outdoor transmitters 1 2 or 3 in the center will indicate from which sensor the current reading originates Display of low battery indicator A small battery symbol on the upper right side indicates low running batteries An antenna symbol in the upper center indicates that a signal is received from the transmitter s DCF 77 RADIO CONTROLLED TIME The time base for the radio controlled time is a Cesium Atomic Clock operated by the Phys
14. electronic wastes contain hazardous substances Disposal of electronic waste in wild country and or in unauthorized grounds strongly damages the environment Please contact your local or and regional authorities to retrieve the addresses of legal dumping grounds with selective collection All electronic instruments must from now on be recycled User shall take an active part in the reuse recycling and recovery of the electrical and electronic waste The unrestricted disposal of electronic waste may do harm on public health and the quality of environment This product must however not be thrown in general rubbish collection points 54 As stated on the gift box and labeled on the product reading the User manual is highly recommended for the benefit of the user The manufacturer and supplier cannot accept any responsibility for any incorrect readings and any consequences that occur should an inaccurate reading take place This product is not to be used for medical purposes or for public information This product is only designed to be used in the home as indication of the future weather and is not 100 accurate Weather forecasts given by this product should be taken only as an indication and not as being totally accurate The specifications of this product may change without prior notice This product is not a toy Keep out of the reach of children No part of this manual may be reproduced without written consent of the manufacturer
15. ey set the time zone The range runs from 0 to 12 and then runs from 12 back to 0 in consecutive 1hour intervals 3 Press the SET key to confirm and enter the Time Reception ON OFF setting or exit the setting mode by pressing the CH key TIME RECEPTION ON OFF SETTING bay Q n D REC 42 Digit flashing In area where reception of the DCF 77 time is not possible the DCF 77 time reception function can be turned OFF The clock will then work as a normal Quartz clock Default setting is ON 1 The digit ON will start flashing on the LCD 23 Use the IN key to turn OFF the time reception function 3 Confirm with the SET key and enter the 12 24 Hour Display setting or exit the setting mode by pressing the CH key Note If the Time Reception function is turned OFF manually the clock will not attempt any reception of the DCF time as long as the Time Reception OFF function is activated The Time Reception and DCF icons will not be displayed on the LCD TIME Q Cc 4 K 24 flashing or z 12 24 HOUR TIME DISPLAY SETTING 1 After setting time reception ON OFF press the SET key 12h or 24h flashes in the LCD 2 Press the IN key to select the 12h or 24h display mode 3 Press the SET again to confirm and to enter the Manual Time setting or exit the setting mode by pressing the CH key Note When 24h mode display is selected the calendar format will be date and month display
16. hat the outdoor temperature reading is receivable In event that the signal is not received relocate the transmitters or move them slightly as this may help the signal reception CARE AND MAINTENANCE Extreme temperatures vibration and shock should be avoided as these may cause damage to the unit and give inaccurate forecasts and readings 52 Precautions shall be taken when handling the batteries Injuries burns or property damage may be resulted if the batteries are in contact with conducting materials heat corrosive materials or explosives The batteries shall be taken out from the unit before the product is to be stored for a long period of time Immediately remove all low powered batteries to avoid leakage and damage Replace only with new batteries of the recommended type When cleaning the display and casings use a soft damp cloth only Do not use solvents or scouring agents as they may mark the LCD and casings Do not submerge the unit in water Special care shall be taken when handling a damaged LCD display The liquid crystals can be harmful to user s health Do not make any repair attempts to the unit Return them to their original point of purchase for repair by a qualified engineer Opening and tampering with the unit may invalidate their guarantee Never touch the exposed electronic circuit of the device as there is a danger of electric shock should it become exposed Do not expose the units to extreme and
17. ht up briefly and a short signal tone will sound Following the indoor temperature humidity and the time as 0 00 will be displayed If this information is not displayed on the LCD after 60 seconds remove the batteries from both units and wait for at least 60 seconds before reinserting them 4 The outdoor temperature and humidity data from the first transmitter channel 1 should then be displayed on the Weather Station Also the signal reception icon will be displayed If this does not happen after 2 minutes the batteries will need to be removed from both units and reset from step 1 5 Insert the batteries in the second transmitter as soon as the outdoor temperature and humidity readings from the first transmitter are displayed on the Weather Station Note User shall insert the batteries into the second transmitter within 45 seconds after the Weather Station displays the information of the first transmitter 6 The outdoor temperature and humidity from the second transmitter and the channel 2 icon should then be displayed on the Weather Station If this does not happen after 2 minutes the batteries will need to be removed from all the units and reset from step 1 TA Insert the batteries in the third transmitter as soon as the channel 2 icon and outdoor data are displayed on the Weather Station Then within 2 minutes the channel 3 outdoor data from the third transmitter will be displayed and the channel icon will shift back to 1 once the thi
18. ikalisch Technische Bundesanstalt Braunschweig which has a time deviation of less than one second in one million years The time is coded and transmitted from Mainflingen near Frankfurt via frequency signal DCF 77 77 5 kHz and has a transmitting range of approximately 1 500 km Your radio controlled Weather Station receives this signal and converts it to show the precise time in summer or wintertime The quality of the reception depends greatly on the geographic location In normal cases there should be no reception problems within a 1 500km radius around Frankfurt Once the outdoor temperature and humidity are displayed on the Weather station after initial set up the DCF tower icon in the clock display will start flashing in the upper left corner This indicates that the clock has detected that there is a radio signal present and is trying to receive it When the time code is received the DCF tower becomes permanently lit and the time will be displayed 40 DCF reception is done twice daily at 02 00 and 03 00 am If the reception is not successful at 03 00 am then the next reception takes place the next hour and so on until 06 00am or until the reception is successful If the reception is not successful at 06 00 am then the next attempt will take place the next day at 02 00 am If the tower icon flashes but does not set the time or the DCF tower does not appear at all then please take note of the following Recommended distance to any in
19. mber will only be displayed if there is more than one transmitter detected 3 To reset the minimum and maximum temperature and humidity data and the times at which they were recorded press the OUT key continuously for about 3 seconds This will reset all minimum and maximum data recorded to the current time date temperature and humidity The current time taken is the normal displayed time and does not regard the time zone set for the unit 49 Note The MIN MAX data for each transmitter needs to be reset separately TO VIEW THE MIN MAX DATA FROM DIFFERENT TRANSMITTERS When more than 1 transmitter used t To toggle between transmitters press the CH key Once to show transmitter 2 Twice to show transmitter 3 Three times to return to transmitter 1 2 Use OUT key to view the MIN MAX temperature and humidity data for the selected transmitter 3 To reset the minimum and maximum temperature and humidity data and the times at which they were recorded press the SET key continuously for about 3 seconds This will reset the MIN MAX data recorded to the current time date temperature and humidity The current time taken is the normal displayed time and does not regard the time zone set for the unit Note the MIN MAX data for each transmitter needs to be reset separately LOW BATTERY INDICATOR Low battery indicator is displayed on the LCD when the batteries require changing THERMO HYGRO OUTDOOR TRANSMITTER The temperature and humi
20. r to the Weather Station in open space However this depends on the surrounding environment and interference levels If no reception is possible despite the observation of these factors all system units have to be reset see Setting up POSITIONING THE WEATHER STATION Mm Y The Weather Station comes attached with removable table stand which provides the option of VAG od table standing or wall mounting the unit Before wall mounting please check that the outdoor k temperature and humidity values can be received from the desired locations To wall mount ti Fix a screw not supplied into the desired wall leaving the head extended out the by about 5mm 2 Remove the stand from the Weather Station by pulling it way from the base and hang it onto the screw Remember to ensure that it locks into place before releasing gt 51 POSITIONING THE THERMO HYGRO OUTDOOR TRANSMITTER d The Transmitter is supplied with a holder that may be attached to a wall with the two L screws supplied The Transmitter can also be position on a flat surface by securing the CE stand to the bottom to the Transmitter jal To wall mount eile Secure the bracket onto a desired wall using the screws and plastic anchors 2 Clip the remote thermo hygro transmitter onto the bracket Note Before permanently fixing the transmitter wall base place all units in the desired locations to check t
21. rd transmitter is successfully received If this does not happen user shall restart the setting up from step 1 Note User shall insert the batteries into the third transmitter within 45 seconds after the Weather Station displays the information of the first transmitter Or immediately after reception of the second transmitter is 35 finished 8 In order to ensure sufficient 868 MHz transmission however the distance between the Weather Station and the transmitter should not be more than 100 meters see notes on Positioning and 868 MHz Reception IMPORTANT Transmission problems will arise if the setting for additional sensors is not followed as described above Should transmission problems occur it is necessary to remove the batteries from all units and start again the set up from step 1 FUNCTION KEYS Weather station The weather station has four easy to use function keys SET key Setting To enter the set mode for the following functions LCD contrast Time zone Time Reception ON OFF 12 24 hour display Manual time Year Date C F and W eather forecasting icon sensitivity settings Note The year can be displayed in the set mode not displayed in normal mode IN key Indoor To toggle between the current minimum maximum indoor temperature and humidity To press for over 3 seconds to reset the indoor maximum and minimum temperature and humidity records will reset all records to current level No
22. te The Time date information is only available for MIN MAX temperature data and will be changed to default time after the reset operation To change LCD contrast time zone Time Reception ON OFF 12 24 hour display hour year month day F and weather forecasting icon sensitivity in s etting modes 36 Note in 24hr time display mode the day is set by using the IN key In 12hr time display mode the month is set by using the IN key OUT key Outdoor To toggle between the current minimum maximum outdoor temperature and humidity Press for around 3 seconds to reset the outdoor maximum and minimum temperature and humidity records will reset all records to current level of the relative transmitter being reset each transmitter s data must be reset separately Note The time date information of MIN MAX temperature will be reset to default time as well To change minute day month units in setting modes Note in 24hr time display mode the month is set by using the OUT key In 12hr time display mode the day is set by using the OUT key CH key Channel To toggle between the Thermo Hygro outdoor transmitters 1 2 and 3 if more than 1 transmitter is used To exit manual setting mode 37 LCD SCREEN TIME DCF Tower Icon for time reception DATE Calendar 1m L FORECAST Weather Tendency Icon Low battery i e E weather station l a A Indoor Temperature in Low battery indicator transmitter sam
23. terfering sources like computer monitors or TV sets is a minimum of 1 5 2 metres Within ferro concrete rooms basements superstructures the received signal is naturally weakened In extreme cases please place the unit close to a window and or point its front or back towards the Frankfurt transmitter During nighttime the atmospheric disturbances are usually less severe and reception is possible in most cases A single daily reception is adequate to keep the accuracy deviation below 1 second MANUAL SETTINGS The following manual settings can be changed when pressing the SET key for LCD contrast setting Time zone setting Time reception ON OFF setting 12 24 Hour setting Manual time setting Calendar setting C F setting Weather forecasting icon sensitivity setting 41 LCD CONTRAST SETTING i le iede flashing The LCD contrast can be set to 8 different levels to suit the users needs default LCD contrast setting is LCD 5 To set the desired contrast level 1 Press the IN key to select the level of contrast desired 2 Press the SET key to confirm and enter the Time Zone setting or exit the setting mode by pressing the CH key TIME ZONE SETTING Time Zone flashing Oh The time zone default of the Weather Station is 0 To change to another time zone ls Press the SET key after completing the LCD contrast setting in order to enter the time zone setting flashing 2 Using the IN k
24. the weather was when it was sunny the sun icon only Therefore the next change in the weather will be the cloud with rain icons since the indicator is pointing downwards Note Once the weather tendency indicator has registered a change in air pressure it will remain permanently visualized on the LCD 47 INDOOR TEMPERATURE AND HUMIDITY READING WITH COMFORT LEVEL INDICATOR Minimum Display INDOOR W HUMIDITY e eo IO gg4 Indoor Relative Indoor Temperature in UZ Humidity The indoor temperature and humidity are measured automatically and displayed on the fourth section of the LCD THE COMFORT LEVEL INDICATORS Comfortable A happy face icon indicating a temperature level between 20 0 and 25 9 68F to 78 6F and humidity between 45 and 65 Uncomfortable A sad face icon indicating any value outside the comfortable range TOGGLING AND RESETTING THE INDOOR RECORDINGS 1 To toggle between the indoor current minimum and maximum temperature and humidity data and the times at which they were recorded press the IN key Once to show the minimum temperature and humidity values with time and date recorded Twice to show the maximum temperature and humidity values with time and date recorded Three times to return to the current time date temperature and humidity levels Note The Time date information is only available for the MIN MAX temperature data 2 To reset the minimum and maximum temperature an
25. utdoor temperature display with MIN MAX recording 31 Indoor and outdoor humidity reading displayed as RH with MIN MAX recordings All MIN MAX temperature recordings show date and time received All MIN MAX recordings can be reset Indoor comfort level indicator happy or sad face icons Can take up to three outdoor transmitters LCD contrast setting Low battery indicator Wireless transmission at 868 MHz Signal reception intervals at 4 seconds Wall mounting or table standing e o o o oo o eee The Thermo Hygro Outdoor Transmitter Remote transmission of outdoor temperature and humidity to Weather Station by 868 MHz Display alternately the outdoor temperature and humidity readings on LCD EEEN Shower proof casing Wall mounting case Mounting at a sheltered place Avoid direct rain and sunshine 32 HOW TO INSTALL AND REPLACE BATTERIES IN THE WEATHER STATION The Weather station uses 3 x AA IEC LR6 1 5V batteries When batteries will need to be replaced the low battery icon will appear on the LCD To install and replace the batteries please follow the steps below TRANSMITTER T Insert finger or other solid object in the space at the bottom center of the battery compartment and lift up to remove the cover 2 Insert batteries observing the correct polarity se
Download Pdf Manuals
Related Search