Zanussi ZWG6144PS washing machine
Contents
1. Disconnect the appliance from the mains supply Cut off the mains cable and discard it Remove the door catch to prevent children and pets to get closed in the appliance 5 place a bowl on the floor 6 let the drain hose run along the floor place the external extremities of the drain and in let hoses in the bowl placed on the floor and let water drain out completely 7 screw the water inlet hose to the tap and the drain hose to the rear of the appliance again www zanussi com When you intend to start the appliance up again make sure that the room temperature is above 0 C Environment concerns The symbol a on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Packaging materials The materials marked with the symbol are recyclable gt PE lt polyethylene gt PS lt polystyrene www zanussi com gt PP lt polypropylene This2. tap Leave the door open to prevent the forma a low frequency By pressing any button the tion of mildew and unpleasant smells appliance will come out of the energy saving Warning If there are children or pets in Stains the house activate the child safety de Door seal vice in the inner side of the door frame for more details read Child safety in the chapter At the end of every Safety Information cycle check from the door seal and remove objects that could be trapped in the fold Stand by during programme setting up and once the programme has finished if the programme selector dial and any button are 5 not touched after a few minutes the energy YS saving system is enabled The pilot lights go off The green pilot light of the button 6 flashes with a Washing programmes Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum psa tia Fabrics Load Type of Laundry COTTONS AUTOMATIC SPIN RE uij 90 Cold DUCTION Main wash Rinses Maximum spin speed at 1400 rpm RINSE HOLD Max load 6 kg Reduced load 3 kg SUPER QUICK White coloured cotton and linen Normally soiled items EXTRA RINSE DELAY START COTTONS PREWASH AUTOMATIC SPIN RE Wg 90 Cold DUCTION Prewash Main wash Rinses Maximum spin speed at 1400 RINSE HOLD rpm SUPER QUICK 1 Max load 6 kg Reduced load 3 kg EXTRA RINSE White coloured cotton and linen Heavy soiled items DELAY START
3. Maximum Load Cotton Spin Speed Maximum Installation Unpacking A Warning Read carefully the Safety information chapter before installing the appliance Warning Remove and keep all transit devices so that they can be re fitted if the appliance ever has to be transpor ted again Necessary tools 60 cm 85 cm 54 cm Information on the electrical connection is given on the rating plate on the inner edge of the appliance door 0 05 MPa 0 8 MPa 6kg 1400 rpm Remove the exter nal film Use a cut ter if necessary Remove the cardboard top Remove the polystyrene packaging materi als Spread the front piece on the floor behind the appli ance and then lay the appliance care fully rear side down on it Make sure that no hoses are www zanussi com crushed in the process Remove the polystyrene base from the bot tom Return appliance to it s upright posi tion Open the door and remove the plastic hose guide the bag containing the instruction booklet and the plastic plug caps from the drum XX N V Sz S34 SF SS SS Al F WW SS KUUL Remove the power supply cable and the draining and inlet hose from the hose hold ers on the rear of the appliance i Unscrew the three bolts and remove the hose holders Slide out the relevant plastic
4. User manual Washing Machine U S F R MANUAL ZWG 6144 PS ZAN USSI Contents Safety information 2 Firstuse a oa ana ana aL 12 Safety instructions ______________ 3 Daily use ______ 2222222 12 Frost precaution _______________ 4 Washing programmes_ 19 Environment concerns ____________ 5 Consumption values ___________ 21 Product description 6 Care and cleaning _______2_____ 22 Technical data ________________ 7 What to do if 24 Installation 7 Subject to change without notice Safety information Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an in correct installation and use causes injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety A Warning Risk of suffocation injury or permanent disability Do not let persons children included with reduced physical sen sory reduced mental functions or lack of experience and knowl edge use the appliance They must have supervision or instruction for the operation of the appliance by a person who is responsible for their safety Do not let children play with the appliance Keep all packaging away from children Keep all detergents away from children Keep children and pets away from the appliance door when it is open If the appliance has a child safety device we recommend you ac tiv
5. the piece of cloth Screw the hose back to the appliance and make sure the connection is tight Turn on the water tap During appliance operation it is possible that the red pilot light of the button 6 flashes and one of the indicator pilot lights illuminates to in dicate that the appliance is not working Before contacting your local Service Centre please carry out the checks listed below Possible cause Solution The light of button 6 flashes and the light 7 1 illuminates Problem with the water The filter in the inlet hose or the inlet valve filter are blocked Clean the water inlet filters read Cleaning the water inlet filters supply wy The water tap is closed Q Washing TN ino Open the water tap Extra Rinse s 3 The inlet hose is squashed or kinked O End Check the inlet hose connection Start Pause Nae ze for more details The light of button 6 flashes and the light 7 2 illuminates Problem with the water drainage 24 www zanussi com Q Washing The drain hose is squashed or kinked NY Extra Rinse Check the drain hose connection Dena The drain filter is clogged ian Pause Ifthe appliance stops working without discharging the water first vo carry out an emergency drain BION Turn the programme selector dial to O L Unplug the appliance Close the water tap If necessary wait until the water has cooled down Unscrew t
6. Tar stains first treat with stain remover me thylated spirits or benzine then rub with deter gent paste Open the door by carefully pulling the door handle outwards Load the laundry Place the laundry in the drum one item at a time shaking them out as much as pos sible Maximum Loads Recommended loads are indicated in the Washing Programmes General rules Cotton linen drum full but not too tightly packed Synthetics drum no more than half full Delicate fabrics and woollens drum no more than one third full Close the door gently Warning Make sure that any fabrics were not trap ped when closing the door www zanussi com Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the envi ronment Although biodegradable detergents contain substances which in large quantities can up set the delicate balance of nature The choice of detergent will depend on the type of fabric delicates woollens cottons etc the colour washing temperature and de gree of soiling All commonly available washing machine deter gents may be used in this appliance powder detergents for all types of fabric powder detergents for delicate fabrics 40 C max and woollens liquid detergents preferably for low tempera ture wash programmes 60 C max for all types of fabric or specia
7. in terms of combined energy and water consumptions for washing normally soiled cotton laundry The water temperature of the washing phase may differ from the temperature declared for the selected programme Consumption values The data of this table are approximate Different causes can change the data the quantity and type of laundry the water and ambient temperature Programmes Load Energy con Water con Approximate Remaining Cc sumption sumption litre programme moisture kWh duration mi nutes Cottons 60 C 6 Cottons 40 C 6 0 75 72 145 52 Synthetics 40 C 3 0 6 57 95 35 Delicates 40 C 3 0 6 65 75 35 Wool Hand wash 30 C 2 0 3 48 55 30 Standard cotton programmes www zanussi com 21 Programmes Energy con Water con Approximate Remaining sumption sumption litre programme moisture kWh duration mi 1 nutes Standard 60 C 6 1 07 54 194 52 cotton coy Standard 60 C 3 0 79 43 172 52 cotton o Standard 40 C 3 0 61 43 167 52 cotton 1 At the end of spin phase Off Mode W Left On Mode W 0 65 0 65 The information given in the charts above are in compliance with the EU Commission regulation 1015 2010 implementing directive 2009 125 EC Care and cleaning AN Warning Switch the appliance off and re move the mains plug from the socket before any cleaning action Maintenance Wash With the use of low temperature washes it is possible to get a build
8. means that they can be recycled by dis posing of them properly in appropriate collec tion containers Ecological hints To save water energy and to help protect the environment we recommend that you follow these tips Normally soiled laundry may be washed with out prewashing in order to save detergent water and time the environment is protected too The machine works more economically if it is fully loaded With adequate pre treatment stains and limi ted soiling can be removed the laundry can then be washed at a lower temperature Measure out detergent according to the wa ter hardness the degree of soiling and the quantity of laundry being washed Product description aes Detergent dispenser drawer Water drain hose Worktop E Drain hose support Control panel E Hose holders Door opening handle Water inlet hose Rating plate on the inner edge Mains cable El Front adjustable feet Back feet Child safety device To activate this device rotate the button To disable this device and restore the possi without pressing it inside the door clockwise bility of closing the door rotate the button anti until the groove is horizontal If necessary usea clockwise until the groove is vertical coin 6 www zanussi com Technical data Dimensions Width Height Depth Electrical connection Voltage Overall power Fuse Water supply pressure Minimum Maximum
9. oa open until the filter re moval www zanussi com before removing the filter remove any fluff or small objects from around the filter if necessary place the filter cover in the right position again open the filter cov er and insert the fil ter again The filter is inserted correctly when the indicator on its top is visible and blocked close the filter cov er insert the mains plug again Cleaning the water inlet filters 23 Important If the appliance doesn t fill it takes a long time to fill with water the starting button flashes red or the display if available shows the relevant alarm see chapter What to do if for more details check if the water inlet filters are blocked To clean the water inlet filters Turn off the water tap Unscrew the hose from the tap Clean the filter in the hose with a stiff brush What to do if The appliance does not start or stops during operation Certain problems are due to lack of simple maintenance or oversights which can be solved with the help of the indications de scribed in the charts without calling out an en gineer Fault code and mal function Screw the hose back onto the tap Make sure the connection is tight Unscrew the hose from the appliance Keep a towel near by because some water may flow Clean the filter in the valve with a stiff brush or with
10. off by turning the selector dial to After a few minutes the door can be opened pay attention to the water level and temperature After closing the door it is necessary to select the programme and options again and to press the button 6 When you start the programme by pressing the button 6 the washing phase pilot light 7 1 illuminates This means that the appliance is operating The additional rinses pilot light 7 2 illuminates when the appliance performs an extra rinse When the programme has finished the end cycle pilot light 7 3 comes on Turn the programme selector dial to O The appliance stops automatically The pilot light of the button 6 and the pilot light corre sponding to the just finished washing phase go off The light 7 3 illuminates If a programme or an option that ends with wa ter left in the tub has been selected and the door remains locked to indicate that the water must be emptied out before opening the door Follow the below instructions to empty out the water 18 Select the draining or spinning programme Reduce the spin speed if needed by press ing the relevant button Press the button 6 At the end of the programme the door can be now opened Turn the programme selector dial to O to switch the appliance off Remove the laundry from the drum and carefully check that the drum is empty If you do not in tend to carry out another wash close the water www zanussi com
11. pro gramme when the appliance is working the red pilot light of the button 6 will flash 3 times to indicate a wrong selection The appliance will not perform the new selected programme To switch the appliance off turn the programme selector dial to the position O To cancel or change a running programme switch the ap pliance off by turning the programme selector dial to the position Select the new programme by turning the se lector to the desired programme Start the new programme by pressing the button 6 again The water in the tub will be not emptied out Push the temperature button to select the most suita ble temperature for washing your laundry By selecting a programme the appliance proposes automati cally the maximum spin speed provided for that programme By selecting Automatic Spin reduction the spin speed is reduced to a half but not less than 400 rpm The relevant light illuminates CW Rinse Hold By selecting this function the water of the last rinse is not emptied out to prevent the fabrics from creasing Before opening the door it will be necessary to empty out the water To empty out the water please read the paragraph At the end of the programme By pressing this button the corresponding pilot light illumi nates Short cycle for lightly soiled items or for laundry which needs only freshening up With this option a reduced load of laundry is recommended Cottons 3 kg Synthet
12. the plug into the power socket There is no power at the socket Please check your domestic electrical installation The main fuse has blown Replace the fuse The programme selector dial is not correctly positioned and the button 6 has not been pressed Please turn the selector dial and press the button 6 again The delay start has been selected If the laundry are to be washed immediately cancel the delay start The end of the drain hose is too low Refer to paragraph in Water drainage in chapter Installation An option or a programme that ends with the water still in the tub or a that eliminates all the spinning phases has been selected Select the draining or spinning programme The laundry is not evenly distributed in the drum Redistribute the laundry Too much detergent or unsuitable detergent creates too much foam has been used Reduce the detergent quantity or use another one Check whether there are any leaks from one of the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp Check the water inlet hose connection The drain or inlet hose is damaged Replace it with a new one The programme is still running Wait the end of washing cycle The door lock has not been released Wait until the door lock is released There is water in the drum Select drain or spin programme to empty out the water The transit b
13. with special care Wash the socks and the gloves inside the bag or a net Remove stubborn stains before washing Blood treat fresh stains with cold water For dried stains soak overnight in water with a spe cial detergent then rub in the soap and water Oil based paint moisten with benzine stain remover lay the garment on a soft cloth and dab the stain treat several times Dried grease stains moisten with turpentine lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth Rust oxalic acid dissolved in hot water or a rust removing product used cold Be careful with rust stains which are not recent since the cellulose structure will already have been dam aged and the fabric tends to hole Mould stains treat with bleach rinse well whites and fast coloureds only Grass soap lightly and treat with bleach whites and fast coloureds only Ball point pen and glue moisten with ace tone lay the garment on a soft cloth and dab the stain Lipstick moisten with acetone as above then treat stains with methylated spirits Treat any re sidual marks with bleach www zanussi com Red wine soak in water and detergent rinse and treat with acetic or citric acid then rinse Treat any residual marks with bleach Ink depending on the type of ink moisten the fabric first with acetone then with acetic acid treat any residual marks on white fabrics with bleach and then rinse thoroughly
14. COTTONS ECO ail 2 W 60 40 AUTOMATIC SPIN RE 8 Main wash Rinses Maximum spin speed at 1400 rpm DUCTION Max load 6 kg RINSE HOLD White and coloured cotton This programme can be selec EXTRA RINSE ted for slightly or normally soiled cotton items The tempera DELAY START ture will decrease and the washing time will be extended This allows to obtain a good washing efficiency by saving energy SYNTHETICS AUTOMATIC SPIN RE uy 60 Cold DUCTION Main wash Rinses Maximum spin speed at 1200 rpm RINSE HOLD Max load 3 kg Reduced load 1 5 kg SUPER QUICK 1 Synthetic or mixed fabrics underwear coloured garments EXTRA RINSE non shrink shirts blouses Normally soiled items DELAY START www zanussi com 19 Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Detergent Compartment Fabrics Load Type of Laundry MIXED FABRICS Cold Main wash Rinses Maximum spin speed at 1200 rpm Max load 3 kg Highly energy efficient cold wash programme for lightly soiled laundry This programme requires a detergent which is active in cold water DELICATES 40 Cold Main wash Rinses Maximum spin speed at 700 rpm Max load kg 3 Reduced load 1 5 kg Delicate fabrics acrylics viscose polyester Normally soiled items WOOL HANDWASH 40 Cold Main wash Rinses Maximum spin speed at 1200 rpm Max load 1 kg Machine washable wool hand washable woollens an
15. LD EXTRA RINSE DELAY START AUTOMATIC SPIN RE DUCTION DELAY START uij AUTOMATIC SPIN RE DUCTION RINSE HOLD EXTRA RINSE DELAY START www zanussi com Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum ett Fabrics Load Type of Laundry p 5 SHIRTS uy 30 AUTOMATIC SPIN RE Main wash Rinses Maximum spin speed at 900 rpm DUCTION Synthetics and mixed fabrics Suitable for 5 6 shirts DELAY START lightly soiled MINI 30 W 30 Main wash Rinses Maximum spin speed at 700 rpm BOCES UES IRE B Max load 2 k DUCTION g DELAY START Synthetics and delicates Lightly soiled items or which only needs freshening up JEANS UW Go Calk AUTOMATIC SPIN RE B Main wash Rinses Maximum spin speed at 1200 rpm DUCTION Max load 3 kg Trousers shirts or jackets in denim and jersey realized with hi RRES HOLD s or jackets in denim and jersey realize DELAY START tech materials The Extra Rinse option is activated automati cally 1 If you select the SUPER QUICK option by pressing button 4 we recommend that you reduce the maximum load as indicated Full loading is possible however with somewhat reduced cleaning results 2 Standard programmes for the Energy Label consumption values According to regulation 1061 2010 these programmes are respectively the Standard 60 C cotton programme and the Standard 40 C cotton programme They are the most efficient programmes
16. ate it General Safety Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket Do not change the specification of this appliance 2 www zanussi com Obey the maximum load volume of 6 kg refer to the Programme chart chapter If the supply cord is damaged it must be replaced by the manu facturer its service agent or similarly qualified persons in order to avoid a hazard The operating water pressure minimum and maximum must be between 0 5 bar 0 05 MPa and 8 bar 0 8 MPa The ventilation openings in the base if applicable must not be obstructed by a carpet The appliance is to be connected to the water mains using the new supplied hose sets Old hose sets must not be reused A Safety instructions Installation Remove all the packaging and the transit bolts Keep the transit bolts When you move the appliance again you must block the drum Do not install or use a damaged appliance Do not install or use the appliance where the temperature is less than 0 C or where it is exposed to the weather Obey the installation instruction supplied with the appliance Make sure that the floor where you install the appliance is flat stable heat resistant and clean Do not install the appliance where the appli ance door can not be fully opened Always be careful when you move the appli ance because it is heavy Always wear safety gloves Make sure that there is air ci
17. cked throughout the delay time If you need to open the door you must set the appliance to PAUSE by pressing the button 6 and then wait a few minutes After you have closed the door press the button 6 again 17 fy Start Pause Start Pause i Indicator pilot lights O Washing Extra Rinse O End At the end of the programme Start the programme by pressing the button 6 To start the selected programme press the button 6 the corresponding green pilot light stops flashing The pilot light 7 1 illuminates to indicate that the appliance starts operat ing and the door is locked If you have chosen a delayed start the appliance will begin the countdown To interrupt a programme which is running press the but ton 6 the corresponding green pilot light starts flashing It is possible to change some options of a running pro gramme before the programme carries them out To restart the programme from the point at which it was in terrupted press the button 6 After the programme has started the door is locked If for any reason you need to open the door set firstly the ap pliance to PAUSE by pressing the button 6 After a few mi nutes it will be possible to open the door lf the door remains locked this means that the appliance is already heating or that the water level is too high In any case do not try to force the door If you cannot open the door but you need to open it you have to switch the appliance
18. d delicate fabrics with hand washing care symbol Note A single or bulky item may cause imbalance If the ap pliance doesn t perform the final spin phase add more items redistribute the load manually and then select the spinning programme RINSE Rinse Short spin speed at 700 rpm Max load 6 kg To rinse and spin cotton garments which have been washed by hand Select the EXTRA RINSE option to intensify the rins ing action The appliance adds additional rinses DRAIN Draining of water For emptying out the water left in the drum in the programmes with Rinse Hold option SPIN Drain and long spin at maximum spin speed at 1400 rpm Max load 6 kg Separate spin for hand washed garments and after pro grammes with the Rinse Hold option selected If the Automat ic Spin reduction is selected by pressing the relevant button the appliance performs a short spin EASY IRON 60 Cold Main wash Rinses Maximum spin speed at 900 rpm In order to obtain the best anti creasing result reduce the load of synthetics items Recommended load 1 Kg Synthetic or mixed fabrics Gentle wash and spin to avoid any creasing The appliance performs additional rinses 20 uij AUTOMATIC SPIN RE DUCTION RINSE HOLD EXTRA RINSE DELAY START AUTOMATIC SPIN RE DUCTION RINSE HOLD SUPER QUICK 1 EXTRA RINSE DELAY START LE LE AUTOMATIC SPIN RE DUCTION RINSE HOLD DELAY START AUTOMATIC SPIN RE DUCTION RINSE HO
19. d over the edge of a sink using the plastic hose guide The end of the drain hose must always be ventilated i e the inside diameter of the drain pipe must be larger than the out side diameter of the drain hose The drain Tie the plastic hose guide to the tap with a string to prevent that the drain hose unhooks when the appliance is emptying Onto a sink outlet spigot Push the drain hose onto the spigot and se cure with a clip ensure a loop is formed in the drain hose to prevent waste from the sink entering the appliance If the outlet spigot has not been used before remove any blanking plug that may be in place Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm 10 hose must not be kinked If your drain hose looks like this see beside you do not require the U piece Just push the hose firmly in to the standpipe Directly to a built in drain pipe in the room wall The drain hose may be extended to a maxi mum of 4 metres An additional drain hose and joining piece is available from your Local Centre www zanussi com Connections overview 7 0 5 bar 0 05 MPa 8 bar 0 8 MPa A max 100 cm max 400 cm 1 In the interest of the environment The appliance should be connected to the FOUL drainage system the water wi
20. he drain hose from the rear support see Frost pre caution and unhook it from the sink or spigot Let it run along the floor Place a bowl on the floor and place the end of the draining hose into the bowl The water should drain by gravity into the bowl When the bowl is full empty it Repeat the procedure until water stops flowing out Screw the draining hose to the rear support and reposition it Open the door and remove the laundry Carry out the drain filter cleaning as described in Cleaning the drain filter At the end of cleaning action close the door and insert the mains plug again Run a drain programme to check if the appliance works now The light of button 6 flashes and the light 7 3 illuminates Door open O Washing The door has not been closed or is not closed properly oe Rinse Close firmly the door O nd AN Start Pause Nad AS Xm S The appliance does not start or stops during Before contacting your local Service Centre operation without any visible alarm please carry out the checks listed below www zanussi com 25 Malfunction Possible cause Solution The appliance does not start The appliance fills then empties immediately The appliance does not empty and or does not spin There is water on the floor The door will not open The appliance vibrates noisily 26 The plug is not properly inserted in the power socket Insert
21. ics and delicates 1 5 kg www zanussi com Extra Rinse SN Super Spin Quick Delay Start o y Delay Start www zanussi com This appliance is designed for saving water However for peo ple with very delicate skin allergic to detergents it may be necessary to rinse the laundry using an extra quantity of water Press simultaneously the buttons 3 and 4 for some seconds the pilot light 7 2 comes on This function stays permanently on To remove it press the same buttons again until the pilot light 7 2 goes off The start of the programme can be delayed by 9 6 or 3 hours by means of this button The relevant light illuminates You must select this option after you have set the programme and before you start the programme Select a delayed start select the programme and the required options select the delay start by pressing the button 5 press the button 6 the appliance starts its hourly countdown The programme will start after the selected delay has ex pired Cancelling the delayed start after having started the programme set the appliance to PAUSE by pressing the button 6 press the button 5 once the light relevant to the selected delay goes off press the button 6 again to start the programme The DELAY START cannot be selected with the drain pro gramme Important The selected delay can be changed only after se lecting the washing programme again The door will be lo
22. l for woollens only The detergent dispenser drawer is provi ded with an insert for liquid detergent Do not use the insert downwards for gelatinous detergents with programmes including pre wash with the delay start option In all these cases you can use metering balls or sachets provided with the detergent Take out the me tering aid at the end of the washing cycle Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric load size degree of soiling and hardness of the water used For the quantity of detergent refer always to what is written on the product packing Use less detergent if you are washing a small load the laundry is lightly soiled large amounts of foam form during washing Degrees of water hardness Water hardness is classified in so called de grees of hardness Information on hardness of the water in your area can be obtained from the relevant water supply company or from your lo cal authority 13 If the water hardness degree is medium or high we suggest you to add a water softener follow ing always the manufacturer s instructions When the degree of hardness is soft readjust the quantity of the detergent Open the detergent dispenser drawer UIJ Compartment for powder or liquid de tergent used for main wash Compart ment for liquid addi tives fabric softener starch Warning If you wish to carry out the prewash p
23. ll then be taken to a sewage works for treatment before being discharged safely into a river It is essential that these appliances are not con nected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution If you require any further advice please contact your local water authority C N WASHING i MACHINE DISHWASHER RAINWATER RUN OFF SURFACE WATER FOULDRAIN DRAINS amp SEWERS FOUL SEWERS UNTREATED SEWAGE TREATMENT DISCHARGE WORKS Yy TREATED DISCHARGE RIVER RIVER K J www zanussi com Electrical connection The appliance must be earthed Make sure that the electrical information on the rating plate agree with your domestic power supply Always use a correctly installed shockproof socket Do not use multi way plugs connectors and extension cables There is a risk of fire Do not replace or modify the mains cable yourself Contact the After Sales Service Make sure that the mains plug and cable is not squashed or damaged by the back of the appliance The mains plug must be accessible without moving machine to enable electrical isolation of appliance prior to cleaning or service Do not pull the mains cable to disconnect the appliance Always pull the mains plug This appliance complies with the E E C Di rectives 11 Warning The appliance is supplied with a 13 amp plug attached Use a 13 amp ASTA app
24. olts and packing have not been removed Check the correct installation of the appliance The appliance is not levelled correctly Adjust the feet The laundry is not evenly distributed in the drum Redistribute the laundry Maybe there is very little laundry in the drum Load more laundry www zanussi com Malfunction Possible cause Solution Spinning starts late or the appliance does not spin No water is visible in the drum Unsatisfactory washing results The appliance makes an unusual noise The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum The laundry is redistributed by reverse rota tion of the drum This may happen several times before the unbalance disap pears and normal spinning can resume If after 10 minutes the laundry is still not evenly distributed in the drum the appliance will not spin In this case re distribute the load manually and select the spin programme Load more laundry The load is too small Add more items redistribute the load manually and then select the spinning programme Appliances based on modern technology operate very economically using very little water without affecting performance Too little detergent or unsuitable detergent has been used Increase the detergent quantity or use another one Stubborn stains have not been treated prior to washing Use commercial products to treat the s
25. or a long time let the water flow until it is clean The first time you use the appliance make sure that there is no leakage Use Warning Risk of injury electrical shock fire burns or damage to the appliance Use this appliance in a household environ ment Obey the safety instructions on the detergent packaging Do not put flammable products or items that are wet with flammable products in near or on the appliance Do not touch the glass of the door while a programme operates The glass can be hot Frost precaution If the appliance is installed in a place where the temperature could drop below 0 C proceed as follows to remove any water remaining inside the appliance 1 unplug the appliance 2 turn off the water tap 3 unscrew the water inlet hose from the tap 4 unscrew the drain hose from the rear sup port and unhook it from sink or spigot Make sure that you remove all metal objects from the laundry Do not put a container to collect possible water leakage under the appliance Contact the Service to ensure which accessories can be used Care and Cleaning Warning Risk of injury or damage to the appliance Do not use water spray and steam to clean the appliance Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal objects Disposal A Warning Risk of injury or suffocation
26. our the detergent for prewash phase among washing items into the drum Warning Depending on the type detergent you use powder of liquid ensure that the flap placed in the main wash compartment is in the desired position Flap for powder or liquid detergent UP Flap position if using POWDER detergent DOWN Flap posi tion if using LIQ UID detergent dur ing main wash If the flap is not in the desired position 14 Remove the drawer Push the drawer edge outwards where indicated by the arrow PUSH to facilitate drawer removal The flap is down and you wish to use powder detergent Rotate the flap up wards Ensure to fit the flap completely in Carefully put the drawer back Measure out the detergent Pour the powder detergent into the main wash com partment LJ The flap is up and you wish to use liquid detergent Rotate the flap downwards Carefully put the drawer back Measure out the detergent For the quantity of detergent refer al ways to what is written on the product packing and ensure that the detergent can be poured in the drawer www zanussi com Pour the liquid detergent in the compart ment J without exceeding the limit indica ted in the flap The detergent must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme A Warning Do not use the flap in DOWN position
27. rculation be tween the appliance and the floor Adjust the feet to have the necessary space between the appliance and the carpet Electrical connection A Warning Risk of fire and electrical shock www zanussi com The appliance must be earthed Make sure that the electrical information on the rating plate agrees with the power sup ply If not contact an electrician Always use a correctly installed shockproof socket Do not use multi plug adapters and exten sion cables Make sure not to cause damage to the mains plug and to the mains cable Should the ap pliance power supply cable need to be re placed this must be carried out by our Serv ice Centre Connect the mains plug to the mains socket only at the end of the installation Make sure that there is access to the mains plug after the installation Do not pull the mains cable to disconnect the appliance Always pull the mains plug Do not touch the mains cable or the mains plug with wet hands Only for UK and Ireland The appliance has a 13 amp mains plug If it is necessary to change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse This appliance complies with the E E C Di rectives Water connection Make sure not to cause damage to the water hoses The appliance is to be connected to the wa ter mains using the new supplied hose sets Old hose sets must not be reused Before you connect the appliance to new pipes or pipes not used f
28. roved BS 1362 fuse if it is necessary to change the fuse in the plug First use Ensure that the electrical and water connections comply with the installation instructions i Ensure that the drum is empty Before the first wash run a cotton cycle at the highest temperature without any Daily use Sort out the laundry Follow the wash code symbols on each gar ment label and the manufacturer s washing in structions Sort the laundry as follows whites coloureds synthetics delicates woollens Before Loading The Laundry BN W Important Make sure that no metal objects are left in the laundry e g hair clips safety pins pins Button up pil lowcases close zip fasteners hooks and poppers Tie any belts or long tapes Remove any hooks e g curtains Never wash whites and coloureds together Whites may lose their whiteness in the wash New coloured items may run in the first wash they should therefore be washed sep arately the first time Rub particularly soiled areas with a special detergent or detergent paste 1 do not use acetone on artificial silk 12 supplied A cut off plug inserted into a 13 amp socket is a serious safety danger Make sure that it is disposed of safely laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of deter gent into the main wash compartment and start the machine Treat curtains
29. spacers AN Warning Do not remove the drain hose from the rear sup port Remove this hose only if it is necessary to drain the water Refer to Frost precaution and What to do if S ff Plug the smaller upper hole and the two large ones with the corresponding plastic plug caps www zanussi com Positioning and levelling Water inlet a Level the appliance by raising or lowering the feet The appliance MUST be level and stable on a flat hard floor If necessary check the setting with a spirit level Any necessary adjustment can be made with a spanner Accurate levelling prevents vibration noise and displacement of the appliance during op eration Repeat the levelling action if the appliance is not level and stable Warning This appliance is free standing only Do not remove the worktop for any reason www zanussi com Connect the hose to a tap with a 3 4 thread cn Loosen the ring nut to angle the hose to the left or right depending on the position of your water tap Do not place the inlet hose downwards After positioning the inlet hose be sure to tighten the ring nut again to pre vent leaks Water drainage Firstly form a hook in the end of the drain hose using the plastic hose guide supplied with the appliance The end of the drain hose can be positioned in four ways Hooke
30. tubborn stains The correct temperature was not selected Check if you have selected the correct temperature Excessive laundry load Reduce the laundry load The appliance is fitted with a type of motor which makes an unusual noise compared with other traditional motors This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning as well as increased stability of the appliance After completing these checks switch on the service centre is on the rating plate We recom appliance and press the button 6 to restart the mend that you write the data here programme If the malfunction shows again contact your Service Centre The necessary data for the Model description MOD anrinninudnnmanas Product number PNO ccdcccctsssordsceccesscescesscesseccsenecess Serial number SIND VE www zanussi com 27 www zanussi com shop ey kes a NX fN 192981731 A 372012
31. up of residues inside the drum We recommend that a maintenance wash be performed on a regular basis To run a maintenance wash The drum should be empty of laundry Select the hottest cotton wash programme To aid cleaning the top part of the additive compart ment should be re moved Use anormal measure of detergent must be a powder with biological properties Cleaning the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly 22 www zanussi com Use a stiff brush to clean and remove all washing powder residue Clean all the removed parts of the dispens er drawer under a tap to remove any traces of accumulated powder Use the previous brush to clean the recess ensuring that upper and lower part of it is well cleaned After having cleaned the dispenser and the drawer recess replace it Cleaning the drain filter The filter permits to hold fluff or foreign bodies left unawares in the laundry The pump must be cleaned regularly To clean the filter proceed as follows turn programme selector dial to position unplug the appliance open the door A turn the drum and align the filter cov er FILTER with the arrow on the door seal gt open the filter cov er by pressing the special hook and by rotating the cov er upwards Lt Warning Keep Cerne the filter cover
32. with Gelatinous detergent or thick detergent Powder detergent With programmes with prewash Do not use liquid detergent if the washing programme doesn t start immediately In all above listed cases use the flap in UP position Set your washing programme Measure out the fabric softener Pour fabric softener or any additives into the compartment marked amp do not exceed the MAX mark in the drawer Any additives must be placed in the ap propriate compart ments of the dispens er drawer just before starting the wash pro gramme Close the detergent dispenser drawer The control panel permits to select a washing programmes and different options When an option button is selected the corresponding pilot light is on Otherwise it is off For compatibility among washing programmes and options see the Washing Programme Chart If an incorrect option is selected the integrated red pilot light of the button 6 flashes 3 times OCO000 www zanussi com 15 Programme selector di al 16 Temperature button Automatic Spin reduc tion and Rinse Hold Super Quick Turn the programme selector dial to the required pro gramme The selector dial can be turned either clock wise or counter clockwise The green pilot light of the but ton 6 starts flashing the appliance is now switched on If you turn the programme selector dial to another
Download Pdf Manuals
Related Search