Philips Saeco Moltio
Contents
1. Lift the pre ground coffee compartment lid and add one scoop of pre ground coffee to the compartment Use only the measuring scoop supplied with the machine Then close the pre ground coffee compart ment lid FN varning Add only pre ground coffee to the pre ground coffee compartment Other substances and objects may cause severe damages to the ma chine Such damages will not be covered by warranty EJ Press the button for an espresso or button for a coffee The brewing cycle starts E After the pre brewing cycle coffee begins to pour out of the dispens ing spout E Coffee brewing automatically stops when the preset level is reached press the button to stop it earlier After brewing the machine returns to the main menu Repeat the steps described above to brew more coffees using pre ground coffee Note If no pre ground coffee is poured into the pre ground coffee compart ment only water will be dispensed If more scoops have been added the machine will not brew the product and any ground coffee will be discharged into the coffee grounds drawer ENGLISH 33 MILK CARAFE This chapter explains how to use the milk carafe to prepare a cappuccino or frothed milk Note Before using the milk carafe clean it thoroughly as described in the Clean ing and Maintenance chapter We recommend filling it with cold milk approx 5 C PN warning Do not pour any other liq2. Green Green Green EN Put back the milk carafe dispenser by shifting it up to the icon Remove the milk carafe and empty it EE Remove the milk carafe and the container from the machine Rinse and fill the milk carafe with fresh water up to the MAX level EE Insert the milk carafe into the machine Pull the milk carafe dispenser to the left up to the icon Place a container under the dispensing spout to start the rinse cycle EE Press the E MENU button The following icon is displayed IH Press the button The following icon is displayed Press the C0 button to select frothed milk E The machine reminds you to insert the carafe and pull out the milk carafe dispenser ENGLISH 61 The following icon is displayed during pre heating time required by the machine Yellow EE Once the machine stops dispensing water repeat steps 13 16 until the carafe is emptied Green EE Remove the milk carafe and the container from the machine Repeat steps 11 16 one more time Disassemble and wash the milk carafe as described in the Weekly Cleaning of the Milk Carafe chapter Monthly Lubrication of the Brew Grou Lubricate the brew group after approximately 500 cups of coffee or once a month You can purchase separately the Saeco grease to lubricate the brew group For further details please refer to the maintenance products page in this manual BEB c
3. PHILIPS The manufacturer reserves the right to make changes without prior notice www philips com saeco 421940437041 Rev 0O0 del 05 02 13
4. ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coffee possible Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin blend and roast The machine is equipped with a self adjusting system that allows the use of all types of coffee beans available on the market apart from caramelized and flavored coffee beans The machine automatically adjusts itself after brewing several cups of cof fee to optimize the extraction of the coffee Adjusting the Ceramic Coffee Grinder Ceramic coffee grinders always guarantee accurate and perfect grinding and coarseness for every coffee specialty This provides for full aroma preservation delivering the truly Italian taste in every cup WN warning The ceramic coffee grinder contains moving parts that may be danger ous Therefore do not insert fingers and or other objects Only adjust the ceramic coffee grinder using the grinder adjustment key You can adjust the ceramic grinders to set the coffee grinding to your personal taste E Remove the coffee bean hopper as shown in the section Removing the coffee bean hopper 28 ENGLISH Press and turn the grinder adjustment knob under the coffee bean hopper one notch at a time Use the coffee grinder adjustment key provided with the machine You will taste the difference after brewing 2 3 cups of coffee PN warning Do not t
5. E To exit press the button Now the machine is ready to brew ye v v iG The machine is now programmed to manage a new filter I Note If the INTENZA water filter is already installed and you want to remove 3 but not replace it select the OFF option instead g If there is no INTENZA water filter installed insert the small white filter previously removed into the water tank CHANGING COFFEE BEANS The machine comes with a removable coffee bean hopper so you can switch easily from one type of coffee bean to another and enjoy a different coffee taste Note You can buy an additional coffee bean hopper as accessory CA6803 To preserve it s taste you can store coffee beans in the bean hopper in the refrigerator Removing the coffee bean hopper To remove the coffee bean hopper follow the steps below E Turn the selector to the gf position BEB caution It may happen that the selector can not be switched as it is blocked by coffee beans In this case move the selector back and forth until the beans are released ENGLISH 23 Lift the sides of the coffee bean hopper with both hands as shown in the image BEB caution Do not remove the bean hopper in a different way to avoid spilling coffee beans EJ After removal put the protection cover on the machine to prevent dust m Note we If you turn on the machine while the coffee bean hop
6. E Empty the drip tray 66 ENGLISH TALC CLEAN ESC TEE EscALER fI B 0 Green Yellow Green Yellow Insert the empty milk carafe EJ Remove the INTENZA water filter from the water tank if it was in stalled and replace it with the small white original one Place the water tank back into the machine E Press the E MENU button The following icon is displayed H Press the button Press the button until the following display is shown ae J Press the button to start the descaling process The machine reminds you to insert the carafe and pull out the milk carafe dispenser Py i Note if you press the button by mistake press the amp button to quit MEM EJ Remove the water tank and pour the entire content of the descal ing solution Then fill the water tank with fresh water up to the CALC CLEAN level EJ Place the water tank back into the machine OERE Descacer fI B START ESC Yellow Yellow Yellow Red ENGLISH 67 E Pull the milk carafe dispenser to the left up to the icon Place a large container 1 5 It under both the milk carafe dispenser and the dispensing spout EH Press the button to start the descaling cycle The machine will start dispensing the descaling solution at interval
7. Saeco Meottio USER MANUAL Type HD8769 Read carefully before using the machine ESPRESSO COFFEE AROMA saeco Mottio CE Register your product and get support at www philips com welcome CAPPUCCINO LATTE MACCHIATO STAND BY IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 2 3 8 9 Read all instructions Do not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surtaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord i
8. c o v o p SPRESSO iS COFFEE a AROMA o c o v U Red E The following icon is displayed I Press the S button to start dispensing hot water El This icon is displayed The machine reminds you to install the water dispensing spout Check that the water dispensing spout is correctly installed Press to confirm The machine will start dispensing hot water Once the water has been dispensed remove and empty the container T Note You can stop the manual rinsing by pressing the button MEM EE Repeat step 7 to 12 until the water tank is empty and the no water icon appears Green ENGLISH 17 EE At the end fill the water tank again up to the MAX level Now the ma chine is ready for brewing coffee You will see the display as shown at the left Note When you haven t used the machine for 2 or more weeks the machine will automatically perform an automatic rinse self cleaning cycle after you switch it on Thereafter you need to initiate the manual rinse cycle as described above The automatic rinse self cleaning cycle is also initiated when the machine has been in stand by mode or switched off for more than 15 minutes After this cycle has been completed you can brew a coffee 18 ENGLISH Measuring and Programming Water Hardness Measuring water hardness is very important for defining the frequency in which the machine
9. 96 EC SS 3 The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable waste collection centre for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 80 ENGLISH TECHNICAL SPECIFICATION The manufacturer reserves the right to make changes to the technical specifications of the product Nominal Voltage Power Rating Power Supply See label on the inside of the service door Housing Material ABS Thermoplastic Size w x hx d Weight 256 x 350 x 470 mm 8 5 kg Power Cord Length 1 2m Control Panel On the front Cup Size 142 Water Tank 1 9 litres Removable type Coffee Bean Hopper Capacity 300g Coffee Grounds Drawer Capacity 14 Pump Pressure 15 bar Boiler Stainless Steel Safety Devices Thermal Fuse GUARANTEE AND SERVICE Warranty For detailed information on your warranty and related conditions please read the warranty booklet
10. AND COFFEE BREWING Before brewing the coffee make sure that there are no warnings shown on the control panel and that the water tank and coffee bean hopper are filled Espresso and coffee brewing using coffee beans EE Place 1 or 2 cups under the dispensing spout E To brew an espresso or a coffee press the _ button to select the desired aroma EJ Press the button for an espresso or button for a coffee o g v EJ To brew 1 cup of espresso or coffee press the desired button once This icon will be displayed H To brew 2 cups of espresso or coffee press the desired button twice T consecutively This icon will be displayed v 6 Note In this operating mode the machine automatically grinds and doses the correct amount of coffee Brewing two espressos or two coffees requires two grinding and brewing cycles automatically carried out by the ma chine aj After the pre brewing cycle coffee begins to pour out of the dispens ing spout Coffee brewing automatically stops when the pre programmed level is reached press the button to stop it earlier 32 ENGLISH Espresso and coffee brewing using pre ground coffee This function allows you to use pre ground and decaffeinated coffee With the pre ground coffee function you can only brew one coffee at a time Ell Press the _ button to select the pre ground coffee function e Green
11. EJ Remove the suction tube A E Remove the fitting B from the milk frother by pulling it outwards al Detach the lid C from the milk carafe dispenser by pulling it down while slightly pressing on the sides Further disassemble as shown in the image 54 ENGLISH EJ Pull the fitting E outwards from the milk frothing device E clean all the parts thoroughly with lukewarm water Note You can also clean these parts in the dishwasher E Reassemble the parts following the reverse order Weekly Cleaning of the Brew Grou The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week El Turn off the machine by pressing the ly button and unplug the power cord Remove the coffee grounds drawer Open the service door EJ Remove and clean the coffee residues drawer ENGLISH 55 EZ To remove the brew group press the PUSH button and pull it by the handle E Thoroughly wash the brew group with fresh lukewarm water and care fully clean the upper filter EE Caution do not use detergent soap to clean the brew group K Let the brew group air dry thoroughly Thoroughly clean the inside of the machine using a soft dampened cloth EJ Make sure the brew group is in the rest position the two reference signs must match If they do no match proceed as described in step 9 E Gently pull down the lever until it touches the brew gr
12. Note Clean the coffee bean hopper and tray from any coffee residuals Chapter Weekly cleaning of the coffee bean hop per the tray and the compartment These problems can be considered normal if the coffee blend has been changed or if the machine has just been installed In this case wait until the machine performs a self adjusting operation as described in section Saeco Adapting System ENGLISH 79 ENERGY SAVING Stand b The Saeco full automatic espresso machine is designed for energy saving as stated by the Class A energy label After 30 minutes of inactivity the machine turns off automatically unless you have differently programmed the stand by time If a product has been brewed the machine performs a rinsing cycle In stand by mode the energy consumption is below 1Wh To turn on the machine press the IY button if the power button on the back of the machine is set to I If the boiler is cold the machine performs a rinse cycle Disposal Do not throw away the machine with the normal household waste at the end of its life but hand it in at an official waste collection centre for recy cling By doing this you help to preserve the environment The packing materials can be recycled Machine unplug the machine and cut the power cord Deliver the appliance and the power cord to a service centre or public waste disposal facility This product complies with EU Directive 2002
13. The display shows the type of coffee beans chosen when the machine is ready for brewing for ARABICA coffee beans for ROBUSTA coffee beans for a MIX of coffee beans 26 ENGLISH Coffee emptying cycle If you want to change coffee beans we recommend that you empty the coffee duct and grinder In this way you will taste the full aroma of the new coffee beans For this follow the steps below El Insert the coffee bean hopper with the new coffee beans Pl Press the E MENU button The machine shows this display T g 0 EJ Press the button to access the programming menu Scroll the 3 pages by pressing the oil button until the following icon is displayed gt EJ Press the button STOP E The machine performs two grinding cycles without brewing coffee 21 3 li V fan Note You can stop the grinding cycle early by pressing the button between the first and second grinding cycle al When the grinding cycles have been finished the following icon is displayed m Green k Note If you have not emptied the coffee duct and grinder you need to brew at least two coffees before you can taste the new coffee beans FN varning Please be aware that when you change coffee blend and switch to decaffeinated coffee still some caffeine traces might be present even after having run the emptying cycle ENGLISH 27
14. by short sprays of milk and steam Danger of burns Wait until the end of the cycle before removing the milk carafe E Fill the milk carafe with milk The level must be between the minimum MIN and maximum MAX indication on the milk carafe f Note Use cold 5 C 41 F milk with a protein content of at least 3 to ensure optimum results when preparing a cappuccino You can use whole milk or low fat milk depending on your personal taste FJ insert the carafe into the machine IEJ Pull the milk carafe dispenser to the left up to the i icon mull Note If the milk carafe dispenser is not completely pulled out steam may come out and it does not froth milk properly EJ Place a cup under the dispensing spout ENGLISH 37 H Press the S button to start the dispensing Ss CAPPUCCINO MACCHIATO e b STAND BY Fal The machine reminds you to insert the carafe and pull out the milk carafe dispenser Green The following icon is displayed during pre heating time required by the machine Ca Yellow EJ When the machine shows the following icon the machine pours the F milk The pouring can be stopped by pressing the button 6 EJ Once the milk froth has been poured the machine brews coffee The F brewing can be stopped by
15. cappuccino You can use whole milk or low fat milk depending on your personal taste FJ Insert the carafe into the machine EEJ Pull the milk carafe dispenser to the left up to the a icon E Note If the milk carafe dispenser is not completely pulled out steam may come out and it does not froth milk properly EJ Place a cup under the dispensing spout Yellow Green Green Green Green ENGLISH 43 E Press the MENU button The following icon is displayed al Press the button The following icon is displayed Press the button to select frothed milk EJ The machine reminds you to insert the carafe and pull out the milk carafe dispenser EJ The following icon is displayed during pre heating time required by the machine E The machine pours a pre defined amount of frothed milk into the cup The pouring can be stopped by pressing the button i Put back the milk carafe dispenser by shifting up to the icon After using the milk carafe clean it as described in the Cleaning and Main tenance chapter 44 ENGLISH Adjusting the frothed milk length Each time this function is selected the machine pours a pre set amount of frothed milk into the cup The machine allows you to adjust the amount
16. is displayed CAPPUCCINO 3 LATTE MACCHIATO b STAND BY c o v L U c o v o z 2 K gt SS s Green ENGLISH 51 EJ Press the button The following icon is displayed Press the r button to select frothed milk HN The machine reminds you to insert the carafe and pull out the milk carafe dispenser EK The following icon is displayed during pre heating time required by the machine Once the machine stops dispensing water the cleaning is finished EE Put back the milk carafe dispenser by shifting it up to the icon Remove the milk carafe and empty it 52 ENGLISH aH Weekly Cleaning of the Machine EE Clean the seat of the drip tray Clean the pre ground coffee compartment with the cleaning brush Weekly cleaning of the milk carafe The weekly cleaning is more thorough as it removes any milk residues from the dispenser El Press the release buttons and remove the top of the carafe Remove the lid ENGLISH 53 EJ Lift the milk carafe dispenser to remove it from the top of the carafe The milk carafe dispenser is composed of five parts that must be removed Each part is identified by capital letters A B C D E shown below in the images
17. m Green LJ Yellow Green Green E Press the button to select Latte Macchiato brewing Fal The machine reminds you to insert the carafe and pull out the milk carafe dispenser The following icon is displayed during pre heating time required by the machine EJ When the machine shows the following icon the machine pours the milk The pouring can be stopped by pressing the button EJ Once the milk froth has been poured the machine brews coffee The brewing can be stopped by pressing thes button EN Put back the milk carafe dispenser by shifting it up to the icon mm Note After using the milk carafe clean it as described in the Cleaning and Main tenance chapter It is possible to prepare a Latte Macchiato with pre ground coffee Press the Q button to select pre ground coffee and pour the pre ground coffee into the compartment ENGLISH 41 Adjusting the Latte Macchiato length Each time the button is pressed the machine pours a pre set quantity of Latte Macchiato into the cup The machine allows you to adjust the amount of brewed Latte Macchiato according to your taste and the size of your cups EJ Fill the milk carafe with milk and install it into the machine Pull the milk carafe dispenser to the left up to the 2f icon Place a cup under the dispensing spout EJ Press and hold the amp button
18. pressing the button 5 E Put back the milk carafe dispenser shifting it up to the icon a heal Note After using the milk carafe clean it as described in the Cleaning and Main tenance chapter It is possible to prepare a cappuccino with pre ground coffee Press the Q button to select pre ground coffee and pour the pre ground coffee into the compartment 38 ENGLISH Adjusting the cappuccino length Each time the S button is pressed the machine pours a pre set quantity of cappuccino into the cup The machine allows you to adjust the amount of brewed cappuccino ac cording to your taste and the size of your cups E Fill the milk carafe with milk and install it into the machine Pull the milk carafe dispenser to the left up to the i icon Place a cup under the dispensing spout i EJ Press and hold the button until the MEMO icon appears on the display Then release the button The machine is now programming L 4 CAPPUCCINO e z EJ The machine reminds you to insert the carafe and pull out the milk carafe dispenser Green E The following icon is displayed during pre heating time required by the machine Yellow Fal When the machine shows the following icon the machine starts to
19. until the MEMO icon appears on the display Then release the button The machine is now programming CAPPUCCINO iG q LATTE MACCHIATO STAND BY a EJ The machine reminds you to insert the carafe and pull out the milk carafe dispenser Green E The following icon is displayed during pre heating time required by the machine Yellow Fal When the machine shows the following icon the machine starts to dispense milk froth into the cup When the desired amount of frothed milk is reached press the button Green Once the milk froth has been poured the machine starts brewing cof Green Now the button is programmed Every time it is pressed the machine will brew the same amount of Latte Macchiato that was programmed fee When the desired coffee quantity is reached press the button 42 ENGLISH MAKING FROTHED MILK PN warning Danger of scalding Dispensing may be preceded by short sprays of milk and steam Danger of burns Wait until the end of the cycle before removing the milk carafe E Fill the milk carafe with milk The level must be between the minimum MIN and maximum MAX indication on the milk carafe wall Note Use cold 5 C 41 F milk with a protein content of at least 3 to ensure optimum results when preparing a
20. G AND MAINTENANCE Daily Cleaning of the Machine BEB caution Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine Your machine gets exposed to moist coffee and lime scale continuously In this chapter it is described in detail which activities you need to perform at which frequency Not doing this will ultimately make your machine stop working properly This repair is NOT covered by your warranty Note Usea soft dampened cloth to clean the machine You may only wash the cup holder grill in the washing machine the other parts need to be washed in lukewarm water Do not immerse the machine in water Do not use alcohol solvents and or abrasive objects to clean the machine Donot dry the machine and or its components using a microwave and or standard oven E Empty and clean the coffee grounds drawer daily with the machine turned on Push gently on the edge of the door of the coffee grounds drawer to release the handgrip Remove the coffee grounds drawer by pulling the handgrip Other maintenance operations can only be carried out when the machine is turned off and unplugged 48 ENGLISH Empty and clean the coffee residues drawer located inside of the ma chine Open the service door remove the drawer and empty it EJ Empty and clean the drip tray Press the side buttons Remove the drip tray Note Empty the drip tray also when t
21. Now the button is programmed Every time it is pressed the machine will brew the same amount of cappuccino that was programmed F dispense milk froth into the cup When the desired amount of frothed c milk is reached press the button Once the milk froth has been poured the machine starts brewing cof g fee When the desired coffee quantity is reached press the n button ENGLISH 39 LATTE MACCHIATO BREWING PN warning Danger of scalding Dispensing may be preceded by short sprays of milk and steam Danger of burns Wait until the end of the cycle before removing the milk carafe E Fill the milk carafe with milk The level must be between the minimum MIN and maximum MAX indication on the milk carafe ba Note Use cold 5 C 41 F milk with a protein content of at least 3 to ensure optimum results when preparing a cappuccino You can use whole milk or low fat milk depending on your personal taste FJ insert the carafe into the machine IEJ Pull the milk carafe dispenser to the left up to the 2 icon imal Note If the milk carafe dispenser is not completely pulled out steam may come out and it does not froth milk properly EJ Place a cup under the dispensing spout 40 ENGLISH eS CAPPUCCINO ia LATTE MACCHIATO 3 N STAND BY y ESC
22. To clean the drip tray place Coffee Oil Remover tablet inside and fill it 2 3rds full with hot water Let the cleaning solution take effect for about 30 minutes then rinse thoroughly ENGLISH 65 DESCALING CALC CLEAN PHILIPS Yellow The descaling process takes approx 35 minutes Limescale builds up inside the machine during use It needs to be removed regularly as it may clog the water and coffee circuit of your machine The machine tells you when descaling is needed If the machine display shows the CALC CLEAN icon it means that you need to descale BEB caution Not doing this will ultimately make your machine stop working prop erly and in this case repair is NOT covered by your warranty Use the Descaling solution only Its formula has been designed to ensure better machine performance You can purchase separately the Descaling solution Please refer to the maintenance products page in this user manual for further details PN warning Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end Never use vinegar as a decalci fier Note During the descaling cycle do not switch off the machine If this has hap pened you have to restart the descaling cycle to fully complete it It will restart from the point the descaling cycle had previously been left To perform the descaling cycle follow the steps below Before descaling
23. a CG d Yellow Water hardness This function allows you to adjust the water hardness setting according to the area where you live 1 very soft water 2 soft water 3 hard water 4 very hard water For more details please see the Measuring and Programming Water Hard ness chapter INTENZA Water Filter This function allows you to manage the INTENZA water filter For more details see the chapter related to filter handling Descaling cycle This function allows you to run the descaling cycle Timer stand by This function allows you to adjust the time the machine will go into stand by mode after the last brewing Contrast This function allows you to adjust the contrast of the display to better view the messages Factory Settings This function allows you to reset all factory values ENGLISH 71 How to program your machine In this example it is shown how to program the display contrast Proceed in the same way to program the other functions The programming menu can only be accessed when the machine is on and shows this display Green ll Press the button to enter the menu EE Press the button to access programming Green EJ The first p
24. acs egini iiie 8 General descriptio Nissanissa iTA NE ENERE 9 PREPARING FOR USE Machine Packaging 10 Machine Installation USING THE MACHINE FOR THE FIRST TIME Circuit priming Automatic rinse self cleaning cycle Manual rinse cyCle ssssssssssesescccecerersssnee Measuring and Programming Water Hardnes INTENZA water filter installation Replacing the INTENZA water filter CHANGING COFFEE BEANS Removing the coffee bean hopper Inserting the coffee bean hopper Coffee bean selection Coffee emptying cycle ADJUSTMENTS Saeco Adapting System Adjusting the Ceramic Coffee Grinder Adjusting the aroma coffee strength Adjusting the coffee dispensing spout Adjusting the Coffee Length ssssssess 30 ESPRESSO AND COFFEE BREWING Espresso and coffee brewing using coffee beans Espresso and coffee brewing using pre ground coffe ENGLISH MILK CARAFE Filling the Milk Carafe Inserting the Milk Carafe Removing the Milk Carafe Emptying the Milk Carafe CAPPUCCINO BREWING Adjusting the cappuccino length LATTE MACCHIATO BREWING Adjusting the Latte Macchiato length MAKING FROTHED MILK Adjusting the frothed milk length HOT WATER DISPENSING CLEANING AND MAINTENANCE Daily Cleaning of the Machine Daily cleaning of the water tank Daily cleaning of the milk carafe Weekly Cleaning of the Machine Weekly cleaning of the milk carafe Weekly C
25. age is displayed v J amp CAPPUCCINO 3 LATTE MACCHIATO 0 STAND BY e E1 Press the button to scroll the function pages until the display con trast function is displayed Yellow 72 ENGLISH ESPRESSO COFFEE z 2 T gt 3 S CAPPUCCINO 7 5 LATTE MACCHIATO 3 0 STAND BY 3 3 amp CAPPUCCINO 3 MACCHIATO MEMO e STAND BY e H Press the and buttons to increase or decrease the value of the function 6 When the display value is changed the OK message appears Press the button to confirm the change Press the eo button to exit the programming menu ium Note The machine will automatically exit the programming menu if you do not push any button for 3 minutes The values that have been changed but not confirmed won t be saved ENGLISH 73 MEANING OF THE DISPLAY SYMBOLS This machine is equipped with a colour coded system to make the user s understanding of the display signals easier The icons are colour coded according to the traffic light principle Ready Signals Green Colour The machine is ready to brew coffee with Arabica coff
26. art ment EJ Press the button one or more times to select the pre ground cof fee function Do not add ground coffee Hf Press the button to start a coffee brewing cycle Fl wait until the machine has dispensed half a cup of water Switch the power button on the back of the machine to 0 64 ENGLISH eS CAPPUCCINO MEMO LATTE MACCHIATO STAND BY e Green EJ Let the solution take effect for approximately 15 minutes Make sure you discard the dispensed water EJ Switch the power button on the back of the machine to I To turn on the machine press the button Wait until the automatic rinse cycle has been completed E Remove the coffee grounds drawer and open the service door Remove the coffee residues drawer and then the brew group EE Wash the brew group thoroughly with fresh water After rinsing the brew group insert it again in its seat until it locks into place see the Weekly Cleaning of the Brew Group chapter Insert the coffee residues drawer and the coffee grounds drawer Close the service door GE Press the button to select the pre ground coffee function Do not add coffee to the pre ground coffee compartment EE Press the button to start a coffee brewing cycle MEMO EH Repeat steps 13 14 twice Empty the container J
27. aution Before lubricating the brew group clean it with fresh water and dry it as described in the Weekly Cleaning of the Brew Group chapter E Apply the grease evenly on both side guides Lubricate the shaft too rege EJ Insert the brew group in its seat until it locks into place see Weekly x Cleaning of the Brew Group chapter Insert the coffee residues y drawer N K E Close the service door Insert the coffee grounds drawer A gt 5 OS Monthly Cleaning of the Brew Group with Coffee Oil Remover Besides weekly cleaning we recommend running the cleaning cycle with pats a Coffee Oil Remover after approximately 500 cups of coffee or once a i osae month This operation completes the maintenance process of the brew group i You can purchase separately the Coffee Oil Remover For further details please refer to the maintenance products page in this manual Ei caution The Coffee Oil Remover tablets are to be used for cleaning only and do not have a descaling function For the descaling procedure use the Saeco descaling solution and follow the procedure described in the Descaling chapter Green ENGLISH 63 E Place a container under the coffee dispensing spout Make sure the water tank is filled with fresh water up to the MAX level EJ Put a Coffee Oil Remover tablet in the pre ground coffee comp
28. by packed separately Service We want to ensure that you remain satisfied with your machine If not done already please register your product at www philips com welcome By doing so we can stay in contact with you and send you cleaning and descaling reminders If you need service or support please visit the Philips website at www philips com support or contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet by packed sepa rately or on www philips com support ENGLISH 81 ORDERING MAINTENANCE PRODUCTS For cleaning and descaling use Saeco maintenance products only You can purchase these at the Philips online shop at www shop philips com service your local dealer or at authorised service centres If you have any difficulties obtaining maintenance products for your ma chine please contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet by packed sepa rately or on www philips com support Overview of Maintenance Products PHILIPS Decalcifier CA6700 PHILIPS _INTENZA Water Filter CA6702 Grease HD5061 pHILIPS aeco i Coffee Oil Remover CA6704 82 ENGLISH PHILIPS Saeco Milk circuit cleaner Milk Circuit Cleaner CA6705 Maintenance Kit CA 6706 MACHINE ACCESSORIES Removable coffee bean hopper CA6803 83
29. damage to the machine ete The term CAUTION and this sign warn against slight injuries and or damage to the machine Warnin Connect the machine to a wall socket which is properly wired Its main voltage should comply with the technical data of the appliance Do not let the mains cord hang over the edge of a table or counter or touch hot surfaces Never immerse the machine mains plug or mains cord in water danger of electrical shock Never direct the hot water jet towards body parts danger of burning Do not touch hot surfaces Use handles and knobs ENGLISH 5 Remove the mains plug from the wall socket Ifa disturbance occurs Ifthe machine will not be used for a long time Before cleaning the machine Pull on the plug not on the mains cord Do not touch the mains plug with wet hands Do not use the machine if the mains plug the mains cord or the machine itself is damaged Do not make any modifications to the machine or its mains cord Only have repairs carried out by a service centre authorized by Philips to avoid a hazard This machine is not intended for use by persons including children with reduced physical sensory or mental capa bilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the machine by a person responsible for their safety Children should be supervised to ensure that they do not play with the machine Never in
30. de crease the value Press the button to confirm the setting EJ Press the amp button to exit the programming menu Now the ma chine is ready to brew INTENZA water filter installation We recommend you to install the INTENZA water filter as this prevents limescale to build up in your machine and preserves a more intense aroma to your coffee You can purchase separately the INTENZA water filter Please refer to the maintenance products page in this user manual for further details Water is a crucial part of every coffee so it s most important to always have it professionally filtered Using the INTENZA water filter will prevent mineral deposits from building up and improve your water quality E Remove the small white filter from the water tank and store it in a dry place 20 ENGLISH Remove the INTENZA water filter from its packaging immerse it ver tically with the opening positioned upwards in cold water and gently press the sides so as to let the air bubbles out EJ Set the INTENZA water filter according to the measurements per formed see previous chapter and indicated on the base of the filter A soft water equals 1 or 2 on the test strip B hard water standard equals 3 on the test strip C very hard water equals 4 on the test strip Qj Insert the INTENZA water filter into the empty water tank Press it until it cannot move further down EJ Fil
31. e coffee bean hopper The brew group must be inserted into the machine Insert the coffee grounds drawer Empty the coffee grounds drawer and the coffee residues drawer Fully insert the coffee grounds drawer before turning the machine off Fill the water tank Insert the coffee bean hopper Insert drip tray Turn off the machine After 30 seconds turn it back on Try this 2 or 3 times If the machine does not start contact the Philips SAECO hotline in your coun try and communicate the Error code which you see on the display You can find its contact details in the warranty booklet by packed separately or on www philips com support ENGLISH 77 TROUBLESHOOTING This chapter summarizes the most common problems you could encoun ter with your machine If you are unable to solve the problem with the information below visit www philips com support for a list of frequently asked questions or contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet by packed separately or on www philips com support Machine actions Causes The machine is not connected to the electric network The machine does not switch on Solutions Connect the machine to the electric network The power button is on position 0 Sometimes water is drained automati cally by the machine into the drip tray to manage the rinsing of the circuits and ensure optimum machine perfor mance T
32. ee beans UPS The machine is ready to brew coffee with Robusta coffee beans L psg Sg The machine is ready to brew coffee with a mix of coffee beans 90 vy The machine is ready to brew pre ground coffee LPs Select the programming menu or special beverages menu W e e Frothed milk or hot water selection S W t S Hot water dispensing gt The machine is brewing one cup of espresso STOP 2 a2 ammm a The machine is brewing one cup of coffee The machine is brewing two cups of espresso 74 ENGLISH Ready Signals Green Colour STOP 29 y STOP The machine is brewing two cups of coffee Coffee brewing using pre ground coffee in progress The machine is programming the amount of coffee to brew Frothed milk brewing The machine is brewing cappuccino STOP gt Se y ap The machine is programming the amount of milk to dispense for the cappuc cino ha o gt STOP The machine is programming the amount of coffee to dispense for the cap puccino The machine is brewing Latte Macchiato The machine is programming the amount of milk to dispense for the Latte Macchiato The machine is programming the amount of coffee to dispense for the Latte Macchiato The machine is programming the amount
33. has to be descaled and to install the INTENZA water filter for more detail on the water filter see next chapter To measure the water hardness follow the steps below E Immerse the water hardness test strip supplied with the machine in TY water for 1 second E note The test strip can only be used for one measurement FJ wait for one minute gt EJ Check how many squares have changed the colour to red and then consult the table Note The numbers on the water hardness test strip correspond to the water hardness adjustment settings More precisely 1 1 very soft water 2 2 soft water 3 3 hard water 4 4 very hard water C A The letters correspond to the references that are located at the base of the INTENZA water filter see next chapter Machine Water Hardness Setting N go A oO E Q lt x N Cc a N EJ Press the E MENU button The machine shows this display Green na pHILIPS Saeco Yellow Yellow Green ENGLISH 19 E Press the button to access the programming menu Scroll the pages by pressing the i button until the following icon is displayed Note The machine is supplied with standard water hardness setting suitable for most types of water al Press the S button to increase the value or the S button to
34. he drip tray gets filled although no water is drained The coffee grounds drawer has been P The red gj icon is always dis g v emptied with the machine off played on the machine Coffee is not hot enough The cups are cold No hot water is dispensed The hole of the water dispensing spout is clogged Coffee does not have enough crema see note Milk does not froth The blend is unsuitable coffee is not freshly roasted or the grind is too coarse The milk carafe is dirty or not inserted correctly Check that the power button is set to This is seen as normal machine behavior The coffee grounds drawer must always be emptied with the machine on Wait until the L icon is displayed before refitting the drawer Preheat the cups with hot water Clean the hole of the dispensing spout using a pin Make sure that the machine is off and cold before performing this operation Change coffee blend or adjust the grind as explained in chapter Adjusting the Ceramic Coffee Grinder Clean the carafe and insert it correctly The milk carafe dispenser has not been correctly pulled out The machine takes along time to The machine circuit is clogged by warm up or the amount of water limescale dispensed from the wand is too little The brew group cannot be removed The brew group is out of place Check that the milk dispenser has been pulled out correctly Descale the machine Turn on the mac
35. he full drip tray indicator is raised ENGLISH 49 Daily cleaning of the water tank EE Remove the small white filter or the INTENZA water filter if installed from the water tank and wash it with fresh water Put the small white filter back or the INTENZA water filter if installed in its housing by gently pressing and turning it at the same time EEJ Fill the water tank with fresh water Daily cleaning of the milk carafe It is important that you clean the milk carafe daily or after each use as it preserves hygiene and ensures perfect milk froth consistency WN warning Danger of scalding Dispensing may be preceded by short sprays of hot water and steam Danger of burns Wait until the end of the cycle before removing the milk carafe El Press the release buttons and remove the top of the carafe Rinse the top of the carafe and the milk carafe with lukewarm water Remove all milk residues EEJ Attach the top on the milk carafe ensure it is locked into place 50 ENGLISH Green EJ Remove the lid and fill the milk carafe up to the MAX level with fresh water H Put the lid back onto the milk carafe Fal Pull the milk carafe dispenser to the left up to the d a icon Place a container under the dispensing spout EJ Press the E MENU button The following icon
36. hine Close the service door The brew group automatically returns to the initial position The coffee grounds drawer is inserted Coffee is not suitable for automatic machines There is a lot of ground coffee under the brew group The machine grinds the coffee There is no water beans but no coffee comes out see note Remove the coffee grounds drawer before removing the brew group It may be necessary to change the type of coffee or the coffee grinder settings Fill the water tank and prime the circuit chapter Using the Machine for the First Time The brew group is dirty Clean the brew group Weekly Cleaning of the Brew Group chapter This might occur when the machine is automatically adjusting the dose Brew a few coffees as described in chap ter Saeco Adapting System The circuit is not primed The dispensing spout is dirty Prime the circuit chapter Using the machine for the first time Clean the dispensing spout 78 ENGLISH Machine actions Coffee is too weak see note Coffee is brewed slowly see note Coffee leaks out of the dispensing spout The selector is locked The coffee bean hopper cannot be inserted Coffee does not taste according to the new beans The R is displayed Causes This might occur when the machine is automatically adjusting the dose Solutions Brew a few coffees as described in chap ter Saeco Ada
37. irectives 2005 95 EC 2002 96 EC and 2003 108 EC on the restriction of the use of certain hazardous substances in electri cal and electronic equipment as well as waste disposal This machine complies with EU directive 2002 96 EC INSTALLATION Product overview ENGLISH 9 General description Coffee bean hopper locking removal selector switch Pre ground coffee compartment Storage area for cups Coffee bean hopper Coffee bean hopper tray Coffee bean hopper lid Control Panel Coffee dispensing spout Cup holder grill Full drip tray indicator Drip tray Water dispensing spout removable Coffee grounds drawer Brew group Coffee residues drawer Service door Milk carafe Water Tank Power cord socket Power button Coffee grinder adjustment key Pre ground coffee scoop Cleaning brush Grease for the brew group Power cord Water hardness test strip Espresso brew button Coffee brew button Aroma Pre ground coffee button Cappuccino brew button Latte Macchiato brew button ON OFF button MENU button Descaling solution to be purchased separately Filter INTENZA to be purchased separately Pr
38. irst time the following activities need to happen 1 You need to prime the circuit 2 The machine will perform an automatic rinse self cleaning cycle 3 You need to initiate a manual rinse cycle Circuit priming During this process fresh water flows through the internal circuit of the machine and the machine warms up This takes a few minutes E Place a container under the coffee dispensing spout Press the button to start the cycle The machine starts the auto See matic priming of the circuit by dispensing some water through the aR coffee dispensing spout COFFEE i AROMA A E EJ The bar under the icon shows the operation progress When the pro cess is completed the machine stops dispensing automatically Yellow Yellow A E1 Then the control panel shows the machine warm up icon o9 14 ENGLISH Automatic rinse self cleaning cycle When warm up is completed the machine automatically performs a rinse self cleaning cycle of the internal circuit with fresh water This takes less than a minute E Place a container under the coffee dispensing spout to catch the small amount of water which will be dispensed The machine shows this display Wait for the cycle to finish automati cally Yellow You can stop dispensing by pre
39. l the water tank with fresh water and reinsert it into the machine Al Dispense all the water of the tank by using the hot water function see chapter Hot water dispensing Fill the water tank again EJ Press the E MENU button The machine shows this display Green El Press the button to access the programming menu Scroll the pages by pressing the oi button until the following icon is displayed MO Yellow Yellow Green ENGLISH 21 I Press the S button to select ON and press the button to con Pea Gl To exit press the oo button Now the machine is ready to brew MEM In this way the machine has been programmed to inform the user of the need to replace the INTENZA water filter Replacing the INTENZA water filter ON OFF WRESEM Yellow Green Yellow When the INTENZA water filter needs to be replaced with a new one the following icon is displayed El Replace the INTENZA water filter as described in the previous chap ter Press the MENU button The machine shows this display EJ Press the button to access the programming menu Scroll the MEMO pages by pressing the tl button until the following icon is displayed E Select the RESET option Press the button to confirm 22 ENGLISH
40. leaning of the Brew Group Weekly cleaning of the coffee bean hopper the tray and the compartment Monthly cleaning of the milk carafe Monthly Lubrication of the Brew Group Monthly Cleaning of the Brew Group with Coffee Oil Remover DESCALING ccssssssscsessssssesscesscscvecssessesssesesnesscssssasscsseesesssssessessssesesesssesueses PROGRAMMING scscssssssssssssssssssssesecesecssscssscesscesssesssesssessnesscessnessnensnensnenes The following parameters can be adjusted How to program your machine MEANING OF THE DISPLAY SYMBOLS TROUBLESHOOTING sccssssssessssscssesssessesesssessesssessesesssessesesessesesesassosscaseosees ENERGY SAVING Stand by Disposal TECHNICAL SPECIFICATION ccscsssosssssssssssssssssesscesssssssssssscessesesesesssscaseosees GUARANTEE AND SERVICE Warranty Service ORDERING MAINTENANCE PRODUCTS MACHINE ACCESSORIES s csssssssessssssssessssssescssevsessssssssesssessesssessnsesesessesscesoes 3 4 ENGLISH IMPORTANT S afety instructions This machine is equipped with safety features Nevertheless read the safety instructions carefully and only use the ma chine as described in these instructions to avoid accidental injury or damage Keep this user manual for future reference yN The term WARNING and this sign warn against possible severe injuries danger to life and or
41. ns Wait until the end of the cycle before removing the milk carafe a Note Before starting the procedure make sure that the water tank is filled up to the MAX level E Fill the milk carafe with water up to the maximum level MAX Pour the milk cleaner bag into the milk carafe and let it dissolve com pletely EJ Insert the carafe into the machine Pull the milk carafe dispenser to the left up to the afa icon EJ Place a container under the dispensing spout Green Vl CAPPUCCINO LATTE MACCHIATO Se b STAND BY as a Green Green E Yellow Green ENGLISH 59 E Press the E MENU button The following icon is displayed KA Press the button The following icon is displayed Press the coe button to select frothed milk The machine reminds you to insert the carafe and pull out the milk carafe dispenser EJ The following icon is displayed during pre heating time required by the machine EJ Once the machine stops dispensing water repeat steps 5 8 until the carafe is emptied FN warning Never drink the solution dispensed during the procedure 60 ENGLISH Rs
42. nto wall outlet To disconnect turn any control to off then remove plug from wall outlet 12 Do not use appliance for other than intended use 13 Save these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be performed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if ca
43. of frothed milk according to your taste and the size of your cups E Fill the milk carafe with milk and install it into the machine Pull the milk carafe dispenser to the left up to the gf icon Place a cup under the dispensing spout EJ Press the E MENU button The following icon is displayed v gL 6 E1 Press the f button The following icon is displayed T g H Press and hold the button to select frothed milk until the MEMO Pe icon appears on the display Then release the button The machine is En now programming J LATTE MACCHIATO MEMO STAND BY l ENGLISH 45 al The machine reminds you to insert the carafe and pull out the milk FT carafe dispenser D G The following icon is displayed during pre heating time required by G the machine g EJ When the desired amount of frothed milk is reached press the S button 2 6 Now the frothed milk button is programmed Every time it is pressed the machine will brew the same amount of frothed milk that was programmed HOT WATER DISPENSING PN warning Danger of scalding Dispensing may be preceded by sprays of hot wa ter and steam Danger of b
44. of milk to dispense for the frothed milk ENGLISH 75 Ready Signals Green Colour START Insert the water dispensing spout and press the oo button to start dispens ing Press to exit The machine will remind the user that the carafe must be inserted Warning Signals Yellow Colour i N E ma STOP START TALC CLEAN ESG The machine is heating up to brew beverages or dispense hot water The machine is heating up during beverages programming The machine is performing the rinse cycle Wait until the machine has com pleted the cycle The machine needs the INTENZA water filter to be replaced The brew group is being reset due to machine reset Refill the coffee bean hopper with coffee beans and restart the cycle Prime the circuit The machine needs to be descaled Press the button to start the descal ing process Follow the steps described in the descaling chapter of this manual If you want to descale later press the oo button to continue using the machine Please note that not descaling your machine will ultimately make it stop working properly In this case repair is NOT covered under your warranty 76 ENGLISH Warning Signals Red Colour it Exx Close the service door Fill th
45. otection cover 10 ENGLISH PREPARING FOR USE Machine Packaging The original packaging has been designed and constructed to protect the machine during transport We recommend keeping the packaging material for possible future transport Machine Installation E Remove the drip tray with grill from the packaging Remove the machine from the packaging sane EJ For best use it is recommended to Choose a safe level surface where there is no danger of overturn ing the machine or being injured Choose a location that is sufficiently well lit clean and near an eas ily reachable socket Allow for a minimum distance from the sides of the machine as shown in the illustration 6 inches QZ Insert the drip tray with grill into the machine Make sure it is fully inserted um Note The drip tray collects the water that comes out of the dispensing spout during each rinse self cleaning cycle as well as coffee that might be spilled during beverage preparation Empty and wash the drip tray daily and each time the full drip tray indicator is raised Ei caution NEVER remove the drip tray when the machine has just been turned on Wait a couple of minutes for the machine to carry out a rinse self cleaning cycle ENGLISH 11 E Push gently on the edge of the water tank door to release the hand grip al Remove the water tank by pulling the handgrip Rinse the water tank with fresh water EJ Fill the wate
46. oup base and the two reference signs on the side of the brew group do match 56 ENGLISH E Make sure the hook to lock the brew group is in the correct position by firmly pressing the PUSH button until it locks into place Check if the hook is at the top end position If it is not please try again E Insert the brew group in its seat again until it locks into place without pressing the PUSH button Insert the coffee residues drawer and close the service door EE Insert the coffee grounds drawer ENGLISH 57 Weekly cleaning of the coffee bean hopper the tray and the com artment Clean the coffee bean hopper the tray and the coffee bean hopper com partment once a week with a cloth to remove any coffee residuals or dust To remove the tray push the hooks on the bottom of the coffee bean hop per This is shown in the picture on the left After cleaning put the tray back into the coffee bean hopper 58 ENGLISH PHILIPS Saeco Milk circuit cleaner Monthly cleaning of the milk carafe In the monthly cleaning cycle we recommend using the Saeco Milk Circuit Cleaner to keep the entire circuit clean of milk residues You can purchase separately the Saeco Milk Circuit Cleaner Please refer to the maintenance products page for further details PN warning Danger of scalding Dispensing may be preceded by short sprays of hot water and steam Danger of bur
47. per has not been p inserted the following icon appears You need to insert the bean hopper first Inserting the coffee bean hopper To insert the coffee bean hopper follow the steps below E Remove the protection cover from the machine Switch the selector to the g position 24 ENGLISH EJ Remove any beans from the coffee bean hopper compartment EJ Insert the coffee bean hopper into the compartment as shown on the image E switch the selector to they position PN warning Please be aware that when you change coffee blend and switch to decaffeinated coffee still some caffeine traces might be present even after having run the emptying cycle COFFEE gt ARABICA g ROBUSTA x ESG Green Yellow Green Green Green ENGLISH 25 Coffee bean selection This function allows you to optimize the grinding for selected type of cof fee beans E Press the E MENU button The machine shows this display E Press the button to access the programming menu Scroll the pages by pressing the oi button until the following icon is displayed EJ Press the button or the button to select the type of coffee beans in the coffee bean hopper EJ Press the B button to confirm the setting E To exit press the oo button MEM The machine is now programmed to optimise the grinding of your coffee beans
48. pting System The coffee is too coarse Change coffee blend or adjust the grind as explained in chapter Adjusting the Ceramic Coffee Grinder The coffee bean hopper selector has been shifted The coffee grind is too fine Switch the selector to the gg position Change coffee blend or adjust the grind as explained in chapter Adjusting the Ceramic Coffee Grinder Circuits clogged Perform a descaling cycle The circuit is not primed Prime the circuit chapter Using the machine for the first time The brew group is dirty The dispensing spout is clogged Some coffee beans may have got stuck The blade placed under the coffee bean hopper has been shifted Clean the brew group Weekly Cleaning of the Brew Group chapter Clean the dispensing spout and its holes Move the selector and repeat this move ment until the bean is released Shift the blade to the end of its guide covering the hole There may be some coffee beans left in the coffee bean hopper compartment The selector is not in the correct posi tion Remove the beans Put the selector in the open position You have not emptied the coffee duct and grinder The coffee bean hopper selector has been shifted You need to brew at least two coffees be fore you can taste the new coffee beans Switch the selector to the gg position The coffee bean hopper and tray are dirty
49. r tank with fresh water up to the MAX level and reinsert it back into the machine Make sure it is fully inserted BE caution Never fill the water tank with warm hot sparkling water or any other liquid as this may cause damage to the water tank and the machine Note Always carry the full water tank as shown in the picture 12 ENGLISH CAPPUCCINO LATTE MACCHIATO q STAND BY Yellow a EJ Remove the coffee bean hopper lid Slowly pour the coffee beans into the coffee bean hopper Note The coffee bean hopper contains a tray which vibrates during grinding This supports the flow of beans into the grinder BEB caution Only coffee beans must be put into the coffee bean hopper Ground coffee instant coffee caramelized coffee or any other object may damage the machine E Put back the coffee bean hopper lid on the coffee bean hopper Gd Insert the plug into the socket located on the back of the machine Insert the plug of the other end of the power cord into a wall socket with suitable power voltage EE Switch the power button to I to turn on the machine The red led next to the button blinks EE To turn on the machine simply press the hy button The control panel indicates that the circuit must be primed ENGLISH 13 USING THE MACHINE FOR THE FIRST TIME When using the machine for the f
50. rcuit BZ The machine now carries out the warm up and automatic rinse cycle to prepare for product brewing ENGLISH 69 Remove and empty the container EJ Empty the drip tray and place it back The descaling cycle is now complete BE Remove the small white water filter and place back the INTENZA water fi Iter into the water tank if it was installed Note At the end of the descaling cycle wash the brew group as described in the Weekly Cleaning of the Brew Group chapter The two rinse cycles are performed in order to have the circuit cleaned with a preset amount of water and ensure proper machine operation If the water tank is not filled up to MAX level the machine might require three or more cycles PROGRAMMING You can adjust the machine functions to your personal preference by ac cessing the program menu The following parameters can be adjusted Coffee temperature This function allows you to adjust the coffee brewing temperature Yellow COFFEE SC Coffee bean selection P ARABICA This function allows you to optimize the grinding for selected type of cof ROBUSTA 2 fee bean A Mx gt Coffee duct emptying cycle This function allows you to empty the coffee duct and grinder before changing coffee beans Yellow Yellow SALG CLEAN b Yellow Yellow Yellow Yellow R
51. re is exercised in their use Ifa long detachable power supply cord or extension cord is used 1 The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over Congratulations on your purchase of a Saeco Moltio One Touch Cappuccino full automatic coffee machine To fully benefit from the support that Saeco offers please register your product at www philips com welcome This user manual applies to HD8769 The machine is suitable for preparing espresso coffees using whole coffee beans and it is supplied with a milk carafe so you can prepare your perfect Cappuccino or Latte Macchiato in a quick and easy way In this user manual you will find all the information you need to install use clean and descale your machine CONTENTS IMPORTANT 06 sasbanasntestatsnsnabsnsstaensasavnsnssendegasessusoayosdsdeaseseveneneacans 4 Safety instructions 4 Warning 4 Caution 5 Compliance with standards ssssssssssesesesceeceeesesssssnsnsssessseceeeeeensnsnsnnseseseseeeeeeeeeessnnnnssseseeeeeeeetensnsnsnessess 7 INSTALLATION 8 PRODUCE OVERVICW
52. s The bar on the display shows the cycle progress Note The descaling cycle may be paused by pressing the button To resume the cycle press the button again This allows you to empty the con tainer or to stay away from the machine for a brief period of time EEJ When this icon is displayed the water tank is empty EE Remove and empty the container and the milk carafe EH Empty the drip tray and place it back 68 ENGLISH Yellow Red Green Yellow Wa Remove the water tank rinse it and fill it up to the MAX level with fresh water Place it back into the machine When inserting the water tank into the machine the display on the left is shown Install the milk carafe into the machine Place back the container under both the milk carafe dispenser and the dispensing spout H Press the S button to start the rinsing cycle EE When this icon is displayed the water tank is empty Repeat steps 14 18 Then continue to step 20 When the water tank is empty remove the water tank rinse it and fill it up to the MAX level with fresh water Place it back into the machine Empty the container and place it back under the dispensing spout When the amount of water needed for the rinse cycle has been completely dispensed this icon on the side is displayed Press the button to quit the descaling cycle The machine automatically primes the ci
53. sert fingers or other objects into the coffee grinder Caution e The machine is for household use only It is not intended for use in environments such as staff kitchens of shops offices farms or other work environments e Always put the machine on a flat and stable surface 6 ENGLISH Do not place the machine on a hot plate directly next to a hot oven heater or similar source of heat Only put coffee beans into the coffee bean hopper If ground coffee instant coffee or any other substance is put in it may damage the machine Allow the machine to cool before putting on or taking off Never use warm or hot water to fill the water tank Use cold water only Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water Descale your machine regularly The machine indicates when descaling is needed Not doing this will make your appliance stop working properly In this case repair is not covered under your warranty Do not keep the machine at temperature below 0 degree Celsius Residue water in the heating system may freeze and cause damage Do not leave water in the water tank when the machine is not used over a longer period of time The water can become contaminated Use fresh water every time you use the machine ENGLISH 7 Compliance with standards The machine complies with art 13 of the Italian Legislative Decree dated 25 July 2005 no 151 Implementation of the d
54. ssing the button EJ When the above steps have been completed the machine shows this display You can now proceed with the manual rinse cycle Green Manual rinse cycle During this process you activate the coffee brewing cycle and fresh water flows through the water circuit This takes a few minutes E Place a container under the coffee dispensing spout Check that the machine shows this display Green ENGLISH 15 EJ Select the pre ground coffee brewing function by pressing the ues button The machine shows this display Note Do not add pre ground coffee into the compartment C Green El Press the button The machine starts dispensing water E When the dispensing has finished empty the container Repeat the operations from step 1 to step 4 twice then continue with step 6 al Place a container under the water dispensing spout Press the MENU button The machine shows this display Green EJ Press the button IG CAPPUCCIN LATTE MACCHIAT STAND E R i SG 16 ENGLISH
55. uids than water for cleaning or milk Filling the Milk Carafe The milk carafe can be filled before use or even during use El Lift the carafe lid as shown in the figure FJ Pour the milk into the milk carafe the milk level must be between the minimum MIN and maximum MAX level indicator shown on the milk carafe EJ The milk carafe is now ready to use 34 ENGLISH Inserting the Milk Carafe El if installed remove the water dispensing spout as shown in the figure Press the two buttons on the side to unlock it and lift it slightly Pull the water dispensing spout to remove it Slightly tilt the milk carafe Insert it all the way into the guides of the machine EJ Push the carafe towards the bottom while rotating at the same time until it is locked at the drip tray Do not use force while inserting the carafe Removing the Milk Carafe El Rotate the carafe upwards until it releases from the insert in the drip tray Thereafter remove it I ENGLISH 35 Emptying the Milk Carafe El Press the release buttons to allow the removal of the top of the carafe Lift the top of the carafe Empty the milk carafe and clean it properly Note After each use clean the milk carafe as described in the Cleaning and Maintenance chapter 36 ENGLISH CAPPUCCINO BREWING PN warning Danger of scalding Dispensing may be preceded
56. urn the grinder more than 1 notch at the time to prevent dam age EJ The reference marks in the compartment for the coffee bean hopper indicate the grind setting There are 5 different grind settings to choose from position for coarse grind lighter taste to position 2 for fine grind bolder taste When you adjust the ceramic coffee grinder to a finer setting your coffee will taste stronger For a milder coffee taste adjust the ceramic coffee grinder to a coarser setting Adjusting the aroma coffee strength Choose your favourite coffee blend and adjust the amount of coffee to be ground until they meet your personal taste You can also select the pre ground coffee function E ESPRESSO E COFFEE Green Green z Note Selection must be made prior to selecting coffee Five choices ey by pressing the a button Each time the button is pressed the aroma changes by one degree according to the s selected amount 2OO extra mild aroma O2OD mild aroma MULO medium aroma OOOO strong aroma 00000 extra strong aroma _ pre ground coffee ENGLISH 29 Adjusting the coffee dispensing spout The height of the dispensing spout can be adjusted to better fit the dimen sions of the cups that you wish to use Move the dispensing spout up or do
57. urns Wait until the end of the cycle before removing the water dispensing spout Slightly tilt the water dispensing spout and then insert it all the way in into the guides of the machine FJ Push the water dispensing spout towards the bottom while rotating at the same time until it is locked in the machine as shown in the figure 46 ENGLISH MENU Green Green E ESPRESSO E z COFFEE z AROMA a z Green EJ Place a container under the hot water dispensing spout E Press the MENU button The following icon is displayed H Press the button The following icon is displayed al Press the button to start the dispensing MEMO This icon is displayed The machine reminds you to install the water dispensing spout Check that the water dispensing spout is correctly installed Press to confirm The machine will start dispensing hot water STOP Yellow Green ENGLISH 47 EJ The following icon is displayed during pre heating time required by the machine EJ Pour the desired amount of hot water To stop the hot water dispens ing process press the button CLEANIN
58. wn with your fingers to adjust its height as shown in the image The recommended positions are For the use of small cups For the use of large cups For the use of glasses for the Latte Macchiato Two cups can be placed under the dispensing spout to brew two coffees at the same time 30 ENGLISH Adjusting the Coffee Length The machine allows you to adjust the amount of brewed coffee according to your taste and or the size of your cups Each time the or button is pressed the machine brews a pre set amount of coffee Each button may be individually programmed for a specific brew setting The following procedure describes the programming of the button E Place a cup under the dispensing spout EA Press and hold the button until the MEMO icon is displayed F Then release the button The machine is now programming fG The machine starts brewing coffee EJ Press the S button as soon as the desired amount of coffee is f reached g oO Now the button is programmed each time it is pressed the machine will brew the same amount of espresso that was just programmed ian Note To program the coffee button the same steps should be followed You should always use the button to stop brewing coffee when the desired amount of coffee is reached even when you are programming the coffee button ENGLISH 31 ESPRESSO
Download Pdf Manuals
Related Search