Beko DFN 6833 dishwasher
Contents
1. Pause Cancel key for 3 seconds 2 Release the key when the Start Pause indicator starts flashing For a couple of minutes the machine will fulfill the necessary operations required to cancel the function Once the Time Delay function is cancelled 00 00 will appear on the Remaining Time indicator G You can select and start a new programme following the cancellation of Time Delay function G Time Delay function can not be set after the programme starts Starting the programme To start your machine after selecting the programme and auxiliary functions press Start Pause Cancel key Once the programme starts to run Remaining Time indicator displays EN the estimated time to the end of the programme Start Pause indicator starts lighting continuously Your machine performs water softening depending onthe hardness level of the supply water Remaining time displayed towards the end in some programmes can be different from the time indicated at the beginning due to this process The total time can also change while the programme is running depending on the ambient temperature where your machine is installed temperature of the supply water and amount of the dishes GJ Pay attention not to open the door of the machine when it is running Stop the machine by pressing Start Pause Cancel key if you have to open the door Then open the door of the machine There may be a rush of vapour whe2. Programme Table e Do not put more detergent than suggested on the detergent package Water softening system G The dishwasher requires soft water If the hardness of the water is above 6 dH the water must be softened and descaled Otherwise ions that create the hardness will accumulate on the surfaces of the dishes and may adversely affect the washing shining and drying performances of the product The product is equipped with a water softening system which reduces the hardness of incoming water This system softens the supply water that enters into the product to a level that will allow washing the dishes with the required quality Adjusting the water softening system Washing performance will increase when water softening system is adjusted properly Use the test stripe supplied with the product to determine the supply water hardness in order to adjust the system 11 EN Adding salt Water softening system needs to be regenerated in order for the product operates with the same performance continuously Dishwasher salt is used for this purpose g g Use in your product only the special softening salts produced particularly for use in dishwashers We recommend using granular or powder softening salts Do not use salts containing insoluble substances such as table salt or common salt in the machine Performance of water softening system may deteriorate in time Salt reservoir will fill with wate
3. check the lid once again at the end of the programme Salty food remnants have remained on dishes for a long time gt gt gt f silverware soiled with such foods will be kept waiting in machine dirt must be removed by prewash or dishes must be washed without being kept waiting Electric installation is not grounded gt gt gt Check if your machine is connected to the actual grounding line Otherwise the static electric created in the product causes arcs on the surfaces of metal items creating pores removing the protective cover on the surface and causing discoloration Intensive cleansers such as bleaches are used gt gt gt Protective cover on metal surfaces gets damaged and looses its efficiency in time when it gets in contact with cleansers such as bleach Do not wash your dishes with bleach Metal items particularly such as knives are used for purposes other then their intended uses gt gt gt Protective cover on the edges of knives may get damaged when they are used for purposes such as opening cans Do not use metal kitchen utensils out of their intended uses Silverware are made of low quality stainless steel gt gt gt Corrosion on such items is inevitable they should not be washed in dishwashers Kitchen utensils that are already corroded are washed in dishwasher gt gt gt Rust on a corroded item can migrate to other stainless steel surfaces and cause corrosion on those surfaces as well Such items should not be
4. designed to allow you create wider areas in the upper or lover section of the machine based on your requirements by adjusting the height 22 EN 2 Repeat the same process to lower the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up Adjusting the height of loaded upper basket depends on the model Basket adjustment mechanism on the upper basket of the machine is designed to allow you create wider areas in the upper or lover section of the machine based on your requirements by adjusting the height of the loaded basket in up or down directions without removing it from the machine To raise the basket 1 Grab one of the upper basket wires right or left and lift it up A 2 Repeat the same process to raise the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up To lower the basket 1 Press the latch on the basket adjustment mechanism right or left to lower the basket B 2 Repeat the same process to lower the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up 23 EN Adjusting the height of empty upper basket depends on the model You can adjust the height of the upper basket according to the size o
5. washed in dishwashers 37 EN Detergent remains in detergent dispenser Detergent dispenser was damp when adding detergent gt gt gt Make sure that the detergent dispenser is dried well prior to filling it with detergent Detergent is added long before the washing process gt gt gt Pay attention to add detergent shortly before start up of the washing Opening of the detergent dispenser lid is prevented during washing gt gt gt Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers Detergent is stored under unsuitable conditions gt gt gt f you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recommend you to use tablet detergents Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Care Decorations and ornaments on kitchen utensils are being erased GJ Decorated glasses and decorated luster porcelains are not suitable for washing in the dishwasher Manufacturers of glassware and porcelain tableware items do not recommend washing such kitchen utensils in the dishwashers either Dishes are scratched GJ Kitchen utensils that contains or are made of aluminum should not be washed in dishwas
6. position Keep holding the keys pressed in this stage 2 Release On Off 1 key while pressing and holding the Half Load 1 2 key 3 Keep the Half Load 2 key pressed for three seconds more 4 Rinse Aid indicator lights up and the Rinse Aid indicator status saved on your machine appears on the display as ON or OFF 5 You can change the status of the indicator as ON or OFF by pressing the Start Pause Cancel key G If you switch off the machine with On Off key when the status is ON then the Rinse Aid indicator will come on when the rinse aid level in your machine becomes low while the machine is in use If you switch off the machine by pressing On Off key when the status is set to OFF then the Rinse Aid indicator will never come on End of programme End of Programme indicator will light up once the washing programme is over 1 Press On Off key to turn off your machine 2 Close the tap 3 Unplug the machine from the socket G Leave your dishes in the machine for about 15 minutes to cool down after they are washed Your dishes will dry in a shorter time if you leave the door of your machine ajar during this period This process will increase the drying effectiveness of your machine 29 EN uuuueJBoid s3 94 Buisn pue somasa ple suu jn e pue 1 su dsip yes 1 u ljos 1972M NJ e YPM JNO palwed aq JsNnW ZPZOG NJ YLM 59uepio22e ul sls BY s lninsui Hul
7. position C 4 Slide the rack down and lock it with the tabs D i Perform the same process in reverse order to open the racks To adjust the height of the racks 1 Fold the rack E 2 Slide the rack up F 3 Open the rack at the desired level N Make sure that the impeller does not touch the dishes you placed on the racks Upper basket height adjustable rack depends on the model Use the lower and upper parts of the height adjustable racks in the upper basket of the machine by sliding them down or up according to the heights of the glasses cups or etc A B C Upper basket drawer depends on the model You can easily place additional desert spoons small forks and knives into the basket drawer installed to the upper basket of your machine Upper basket glass support piece depends on the model When placing long stemmed glasses or wine glasses do not lean them against other pieces but to the edge of the basket or to the rack 1 Do not lean long glasses against each other They can move and get damaged during washing If you wish to place large volume pieces on the upper basket release the tab of the glass support piece from the upper basket wire it is hooked to Thus you can obtain a wider space III NCC ee pall eee PT L e STII Wow Collapsable upper ba
8. the drainpipe in order to prevent any dislocation of the water discharge hose during operation of the product G Drainpipe must be connected to the sewage system and it should not be connected to any surface water EN Adjusting the feet If the door of the product cannot be closed properly or if the product swings when you push it slightly then you need to adjust the feet of the product Adjust the feet of the product as illustrated in the installation manual supplied with the product Aquasafe depends on the model Protect the Aquasafe system against water leaks that may occur at hose inlet Water contact with the valve box of the system must be prevented Otherwise electrical assembly will get damaged If the Aquasafe system is damaged unplug the product and call the Authorised Service Agent N As the hose set contains electrical connections and assemblies never shorten or lengthen the hose with extension hoses 3 4 9 Electrical connection Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Manufacturer shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations e Connection must comply with national regulations e Power cable plug must be within easy reach after installation Unplug the product after the washing programme is
9. turned off and on again If you want to disable these functions after turning the machine off and on again you must press the relevant keys again Start Pause Cancel key It is used to start pause or cancel the selected programme or function To press the Start Pause Cancel key wait for two seconds after you turn on the machine by pressing the On Off key An image will be displayed within this time Programme Selection key It is used to choose the washing programme you selected in the Table of Programme Data and Average Consumption Values Half Load key It is used to operate the machine without loading it completely 1 Load your dishes in the machine as you like Press the On Off key 3 Select the desired programme and press the Half Load key Half Load 1 2 indicator will appear on the display 4 Press Start Pause Cancel key to start the programme GJ With the Half Load function you can save both water and power while using the lower and upper baskets of the machine Tablet Detergent key This function provides better drying performance with the multi purpose detergents such as 2in1 3in1 4in1 5in1 all in one etc depending on the hardness level of the supply water Look at the Table of Programme Data and Average Consumption Values to see which programmes the Tablet Detergent function can be used with G Tablet Detergent Indicator G lights when the Tablet Detergent func
10. DISHWASHER Please read this user manual first Dear Customer We hope that you get the best results from the product which has been manufactured in state of the art plants and passed through a strict quality control procedure Therefore please read the entire user manual carefully before using the product and keep it as a reference for future use In case of transferring the product to someone else give the manual as well The user manual will help you use your product in a fast and safe way e Read the user manual before installing and starting your product e Always follow the safety instructions e Keep this user manual within easy reach for future reference e Read also the other documents supplied with the product Remember that this user manual is also applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this User Manual the following symbols are used Important information or useful hints about usage Warning for hazardous situations with regard to life and property Warning for electric shock CONTENTS 1 Dishwasher 3 2 Important safety instructions 5 General safety 5 Intended use 5 Children s safety 6 3 Installation 7 Appropriate installation location 7 Connecting water supply 7 Connection to the drain 8 Adjusting the feet 9 Aquasafe 9 Electrical connection 9 Initial use 9 Disposing of packaging material 10 Trans
11. Never unplug by pulling on the cable always pull out by grabbing the plug The product must be unplugged during installation maintenance 5 cleaning and repairing procedures Always have the installation and repairing procedures carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons Never use chemical solvents in the product They bring forth risk of explosion When you pull the upper and lower baskets out completely the door of the product will bear all the weight of the baskets Do not put other loads on the door otherwise the product may tilt Never leave the door of the product open apart from loading and unloading procedures Do not to open the door of the product when it is running unless necessary Be careful for the rush of hot steam when you need to open the door Intended use EN This product has been designed for domestic use It must be used to do the domestic type dishes only Only dishwasher safe detergents rinse aids and additives must be used The manufacturer waives any responsibility arisen from incorrect usage or transportation The service life of your product is 10 years During this period original spare parts will be available to operate the appliance properly This product should not be used by persons with physical sensory or mental disorders or unlearned or inexpe
12. Pause indicator P starts flashing For a couple of minutes the machine will fulfill the necessary operations required to cancel the programme Once the Time Delay function is cancelled 00 00 will appear on the Remaining Time indicator G You can select and operate a N 28 EN new programme following the cancellation of the programme G There might be residues of detergent or rinse aid left in the machine and or on the pieces being washed depending on the step the previous programme was in at the time of such cancellation Salt indicator Check the Salt indicator on the display to see whether there is enough softening salt in your machine or not You need to refill the salt container whenever the Salt indicator lights G Ifthe water hardness level is saved as r1 Salt indicator will never come on even if the salt container is empty Adjusting the water hardness level is explained in Water Softening System section Rinse Aid indicator Check the Rinse Aid indicator on the display to see whether there is enough softening rinse aid in your machine or not You must refill the rinse aid container when the Rinse Aid indicator comes on G Ifthe Rinse Aid indicator is set to OFF Rinse Aid indicator will never come on even if the rinse aid container is empty Setting the Rinse Aid indicator 1 Turn on your machine by pressing On Off key while pressing and holding the Half Load 2 key when the machine is in off
13. a blue trace after wiping them by hand it must be decreased This is set to position 4 as factory default Items not suitable for washing in the dishwasher Never wash dishes soiled by cigarette ash candle remnants polish dyestuff chemicals etc in your dishwasher Do not wash iron alloy items in the dishwasher It can get corroded or leave stains on other items Do not wash silverware and cutlery with wooden or bone stems glued pieces or pieces that are not resistant to heat as well as copper and tin plated containers in the dishwasher Decorative prints of chinaware as well as aluminum and silver items may get discoloured or tarnished after washing in the dishwasher just as it happens in handwashing as well Some delicate glass types and crystals may become dull in time We strongly recommend you to check if the tableware you are going to purchase is suitable for washing especially in the dishwasher Placing the dishes into the dishwasher You can use your dishwasher in the optimum way with respect to energy consumption and washing and drying performance only if you place the dishes in an orderly way e Wipe away any coarse food remnants bones seeds etc on the dishes before placing them in the dishwasher e Place thin narrow pieces in the middle sections of baskets if possible e There are two separate baskets in which you can place your dishes in the dishwasher Place the heavily soiled and
14. ause the detergent not dissolve completely and will also cause scratches on the glassware Tablet detergents Table detergents exhibit water softening and or rinse aid effect in addition to detergent effect Some types of these detergents also contain special purpose washing chemicals such as glass and stainless steel protectors G Tablet detergents give satisfying results only under certain usage conditions The best washing performance in dishwashers is obtained by using detergent 14 rinse aid and water softening salt individually GJ Information about suitable places detergent dispenser basket etc in the dishwasher to place the tablet can be found amongst the usage instructions on the packages of the tablet detergents Tablet detergent types commonly found in the market 2in1 Contains detergent rinse aid or water softening salt 3in1 Contains detergent rinse aid and water softening salt 4in1 Contains glass protectors in addition to detergent rinse aid and water softening salt 5in1 Contains glass and stainless steel protectors in addition to detergent rinse aid and water softening salt G Observe the instructions of the detergent manufacturer on the package when using tablet detergents When you switch to powder detergent from tablet detergent 1 Make sure that salt and rinse aid reservoirs are full 2 Set the water hardness to the highest level and perform an empty run 3 After the e
15. bigger items in the lower basket and smaller delicate and light items in the upper basket e Place the hollowed dishes such as bowls glasses and pans upside down in the dishwasher Thus accumulation of water in deep hollows is prevented A To prevent possible injuries always place the sharp and pointed dishes such as service fork bread knife etc upside down so as their pointed ends will face down or they will lie horizontally on the dish baskets e Unload dishes in the lower basket first and then the dishes in the upper basket 16 EN Suggestions for loading the dishwasher Improper Loading Of Dishware fay ve i Ol HX JIN Mero AULN YME Silverware basket Movable silverware basket depends on the model depends on the model Silverware basket is designed to wash Since the cutlery basket can be moved your dishes such as fork spoon and A B you can create a wider space etc in a cleaner manner while placing your dishes to the lower basket and free up space for your dishes in different sizes Silverware basket piece depends on the model You can place your forks spoons and etc to upper basket with the additional piece in the figure 18 EN Collapsable lo
16. ck the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine e Machine is unloaded right after the programme is over gt gt gt Do not unload your machine right after washing process is completed Slightly open the door and wait for evacuation of the steam inside for a while Unload the dishes after the pieces cool down to a touchable level Start unloading process from the lower basket Thus dropping of water remained on a piece at upper basket onto the pieces at lower basket is prevented Selected programme is unsuitable gt gt gt Since rinsing temperature is low at programmes with short duration drying performance will also be low Select programmes with longer duration for a higher drying performance Surface quality of the kitchen utensils is deteriorated gt gt gt Desired washing performance can not be obtained at kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well Also water can not flow easily on deteriorated surfaces It is not recommended to wash such kitchen utensils in dishwasher G Itis normal that drying complaints can be experienced with Teflon kitchen utensils It is associated with the structure of Teflon Since the surface tensions of Teflon and water are different water droplets will remain as beads on the Teflon surface Tea cafe or lipstick stains remain on
17. dishes Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Surface quality of the kitchen utensils is deteriorated gt gt gt Tea and cafe stains or other dye spots may not be cleaned in dishwasher when they have penetrated in deteriorated surfaces Desired washing performance can not be obtained at kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well It is not recommended to wash such kitchen utensils in dishwasher Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed container if possible For ease of storing we recommend you to use tablet detergents 35 EN Lime traces remain on dishes and glassware gains a misty appearance Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the pr
18. ds on the model 2 Upper impeller 3 Lower basket 4 Lower impeller 5 Filters 6 Control panel 7 Door 8 Detergent dispenser 9 Lower impeller slot 10 Silverware basket 11 Salt reservoir lid 12 Upper basket rail 13 Upper basket with rack 14 Fan drying system depends on the model 3 EN Technical specifications Development production and sales stages of this product comply with the safety rules included in all pertaining European Community regulations 2006 95 EC 2004 108 EC 93 68 EC IEC 60436 EN 50242 C This product complies with the following EU directives Power input 220 240 V 50 Hz Total power consumption 1900 2200 W Heater power consumption 1800 W Total current depends on the model u OPE Pale Drain pump power i 30 W consumption Water pressure 0 3 10 bar 3 100 N cm 0 01 1 0 Mpa G Technical specifications may be changed without prior notice to improve the quality of the product G Figures in this manual are schematic and may not match the product exactly G Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant standards Depending on operational and environmental conditions of the product these values may vary Note for test institutions Data required for performance tests shall be provided upon request Requests can be e mailed to the following addre
19. e that the water inlet and discharge hoses are not folded pinched or crushed while pushing the product into its place after installation or cleaning procedures When placing the product pay attention not to damage the floor walls piping etc Do not hold the product from its door or panel to move it Appropriate installation location e Place the product on a solid and 7 flat floor that has sufficient load carrying capacity The product must be installed on a flat surface in order for the door to be closed comfortably and securely e Do not install the product at places where temperature may fall below 0 C e Place the product at least 1 cm away from the edges of other furniture e Place the product on a rigid floor Do not place it on a long pile rug or similar surfaces Do not place the product on the power cable e Make sure that you select a location that will allow you to load and unload the dishes in a fast and comfortable manner e Install the product in a place close to the tap and the drain hole Select the installation location by considering that it will not be changed after the connections are made Connecting water supply We recommend attaching a filter on the house apartment supply water inlet to protect the machine from damages that may arise from impurities sand dirt rust etc coming from the urban water supply system or from your own water system as well as to prevent complai
20. ewash programme to remove the Salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme There is a different odour in the machine Anew machine has a peculiar odour It will fade out after a couple of washing Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Dirty dishes are kept in dishwasher for 2 3 days gt gt gt If you are not going to start the machine right after you have put the dishes into it remove the remnants on the dishes and run the Prewash programme without detergent every 2 days In such cases do not close the door of the machine completely in order to avoid odour build up in machine You can also use commercially available odour removers or machine cleaners 36 EN Rust discoloration or surface deterioration occurs on dishes Salt leakage exists gt gt gt Salt may cause deterioration and oxidation on metal surfaces Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen
21. f the dish to be washed Use basket rollers to change the basket height 1 Turn the stoppers on the ends of the upper basket rails by turning them aside A 2 Take the basket out B 3 Change the position of the rollers place the basket into the rail and close the stoppers C Z gt SSS 24 EN B Operating the product 1 4 56 9 78 1 On Off key 6 Express key 2 Start Pause Cancel key 7 Tablet Detergent key 3 Display 8 Time Delay key 4 Programme Selection key 9 Handle 5 Half Load key 10 11 12 13 14 PHI Z 10 Programme indicator 19 Child Lock indicator 11 Remaining Time Delay Time 20 Programme Steps Follow up indicator indicators 12 Start Pause indicator a Washing Step indicator EA 13 Time Delay indicator b Rinsing Step indicator 23 14 15 16 17 18 Rinse Aid indicator Half Load 1 2 indicator Express indicator Tablet Detergent indicator Salt indicator 25 EN a o c Drying Step indicator d End of Programme indicator gt Keys On Off key It is used to turn on or off the machine In On position the machine switches on with the last programme in use In Of position indicators on the display will turn off If the Half Load Tablet Detergent Child Lock and Time Delay functions were selected in the previous programme used these functions will remain active when the machine is
22. gged remove and clean the impeller Pull the lower impeller up to remove it A B 32 EN Upper impeller Check if the holes on the upper impeller 2 are clogged If they are clogged remove and clean the impeller Turn its nut to left to remove the upper impeller C D Make sure that the nut is tightened well when installing the upper impeller 33 EN Troubleshooting Machine does not start Power cable is unplugged gt gt gt Check if the power cable is plugged in Fuse is blown gt gt gt Check the fuses in your house Water is cut gt gt gt Make sure that the water inlet tap is open Door of the machine is open gt gt gt Make sure that you have closed the door of the machine On Off button is not pressed gt gt gt Make sure that you have turned on the machine by pressing the On Off button Dishes are not washed clean Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Impellers are stuck gt gt gt Prior to starting the programme turn the lower and upper impellers by hand to make sure that they rotate freely Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as
23. heck the discharge hose If necessary remove the discharge hose clear the blockage and insert is as illustrated in the user manual G If you cannot eliminate the problem although you follow the instructions in this section consult your dealer or the Authorised Service Agent Never try to repair a nonfunctional product yourself 39 EN EN 17 7767 01 00_AH_YM
24. her Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Spilled salt can cause scratches Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Dishes are not placed orderly in the machine gt gt gt When placing the glasses and other glassware into the basket lean them not against other dishes but the edges or racks of the basket or the glass support wire Striking of the glasses to each other or to other dishes due to the impact of water during washing can cause breaks or scratches on their surfaces 38 EN A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand A bluish rainbow appearance occurs when the glass is pointed to light Excessive rinse aid is used gt gt gt Lower rinse aid setting Clean the spilled rinse aid when adding rinse aid Corrosion has occurred on glass due to soft water gt gt gt Measure the hardness of the supply water appropriately and check the water hardne
25. illustrated in section Cleaning and Care Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Filters are installed incorrectly gt gt gt Check the filter system and make sure that it is installed correctly Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed container if possible For ease of storing we recommend you to use tablet detergents Detergent is not sufficient gt gt gt If you are using powder detergent adjust the amount of detergent according to the soiling degree of your dishes and or programme definitions We recommend you to use tablet detergents for optimum results Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Detergent dispenser lid is left open gt gt gt Make sure that the detergent dispenser lid is closed tightly after adding detergent 34 EN Dishes are not dry at the end of cycle Dishes are not placed orderly in the machine gt gt gt Place your dishes in a way that no water will accumulate in them e Rinse aid is not sufficient gt gt gt Che
26. ilters Clean the filters at least once a week in order for the machine operates efficiently Check if food residues are left on the filters If there are food residues on filters take them out and clean well under running water 3 Press the two pawls on the coarse filter inwards and separate the coarse filter from the assembly C 4 Clean all three filters under tap water by means of a brush 5 Replace the metal plastic filter 6 Place the coarse filter into the microfilter Make sure that it is properly seated Turn the coarse filter clockwise until a click sound is heard N Do not use the dishwasher without filter G Incorrect placement of the filters will reduce washing efficiency Cleaning the hose filter Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation such as sand dirt rust etc can be prevented by means of the filter attached to the water inlet hose Check the filter and the hose regularly and clean them if necessary 1 Turn off the tap and remove the hose 2 After taking out the filter clean it under running tap water 3 Place the cleaned filter back to its seat in the hose 4 Install the hose to tap Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently Lower impeller Check if the holes on the lower impeller 1 are clogged If they are clo
27. ly on glasses after the washing programme is over Adding detergent G Refer to the Programme Table to determine the correct amount of detergent for the selected programme A Do not put solvents into the detergent dispenser There is the risk of explosion Put the detergent into the detergent dispenser just before operating the machine as illustrated below 1 Push the latch to right to open the detergent dispenser lid A 2 Put suggested amount of powder or tablet detergent in the dispenser GJ Inside the detergent dispenser there are level markings that help you use appropriate amount of detergent When brimful detergent dispenser will contain 40 cm of detergent Fill detergent up to 15 cm or 25 cm level marks in the detergent dispenser according to fullness of the machine and or soiling degree of the dishes 1 GJ If dishes have been waiting for a long time and have dried residues fill the 5 cm compartment too 5 13 EN 3 Close the detergent dispenser lid by pressing on it lightly A click will be heard when the lid is closed GJ In programmes with prewash and at high temperature in which you use tablet detergents make sure that the detergent dispenser lid is closed firmly G Use powder detergent in short programmes without prewash since the solubility of the tablet detergent changes depending on the temperature and time Excessive usage of powder detergents will c
28. mpty washing cycle review the user manual and readjust the water hardness level so as to suit the water supply 4 Make the appropriate rinse aid settings GJ Depending on the model salt indicator and or rinse aid indicator must be enabled again if they were disabled before EN Rinse aid g The rinse aid used in dishwashers is a special combination used to increase drying efficiency and prevent water or limescale stains on the washed items For this reason care must be paid to have rinse aid in the rinse aid reservoir and to use rinse aids produced specially for dishwashers only Check Rinse Aid Indicator to determine whether it is necessary to add rinse aid or not 3 depends on the model Having a dark light on the indicator shows that there is sufficient amount of rinse aid in the dispenser If the colour of the indicator is light add rinse aid 1 Open the lid of the rinse aid reservoir by pressing its latch B 2 3 g Fill the reservoir until MAX level Close the lid of the reservoir by pressing on it lightly Wipe clean any spilled rinse aid outside the reservoir Rinse aid that spilled accidentally will cause foaming and it will eventually decrease washing performance 15 EN 4 Turn the rinse aid amount adjuster manually to a position between 1 and 6 4 If there are stains on tableware items after washing level must be increased and if there is
29. n you open the door of your machine be careful Close the door of your machine and press Start Pause Cancel key again Programme will resume running Child Lock You can prevent other people from interrupting and changing the programme cycle and delay time while the machine is running 1 Press and hold the Programme Selection key and the Half Load key simultaneously for three seconds to activate the child lock Child Lock indicator will appear on the display Repeat the same procedure to disable the Child Lock GJ Child lock prevents the selected programme or functions from being changed and disables the Start Pause Cancel key GJ Child Lock does not lock the door of the machine Programme follow up You can follow up the washing step in which the current programme is in from the Programme Steps Follow up indicators on the display PITI EE TITI LUE EI Vo PG CAE La b e d 20 a Washing Step indicator b Rinsing Step indicator c Drying Step indicator d End of Programme indicator Indicators for Washing Rinsing and Drying will light respectively on the display while the selected programme is running Only the End of Programme indicator lights up when the programme is over 00 00 appears on Remaining Time indicator m a programme Press and hold Start Pause Cancel key for 3 seconds while the programme is running Release the key when the Start
30. nts such as yellowing or sludge accumulation at the end of washing EN Permitted water temperature up to 25 C The dishwasher may not be connected to open warm water devices or flow through water heaters e Do not use old or used water inlet hose on the new product Use the new water inlet hose supplied with the product e Connect the water inlet hose directly to the water tap Pressure coming from the tap should be minimum 0 3 and maximum 10 bars If the water pressure exceeds 10 bars a pressure relief valve should be installed in between Use a screw on hose connector to connect the water inlet hose to a water tap with a inch external thread If required use a filter insert to filter deposits from the pipes g 3 4 Fain 10 a 3 4 N e Open the taps completely after making the connections to check for water leaks For your safety close the water inlet tap completely after the washing programme is over ia OOOO we 4 T 8 Connection to the drain Water discharge hose can directly be connected to the drain hole or sink s drainage The length of this connection must be min 50 cm and max 100 cm from the floor 10 22 3 40 50 6 0 8 9 100 110 0 A discharge hose longer than 4 meters causes dirty washing Attach the water discharge hose to the drainpipe without bending it Tightly fix the water discharge hose to
31. over e The voltage and allowed fuse or breaker protection are specified in the Technical specifications section If the current value of the fuse or breaker in the house is less than 16 Amps have a qualified electrician install a 16 Amp fuse e The specified voltage must be equal to your mains voltage e Do not make connections via extension cables or multi plugs Damaged power cables must be replaced by the Authorised Service Agent If the product has a failure it should not be operated unless it is repaired by the Authorised Service Agent There is the risk of electric shock Initial use Before starting to use the product make sure that all preparations are made in accordance with the instructions in sections Important safety instructions and Installation e To prepare the product to do the dishes perform first operation in the shortest programme with EN detergent while the machine is empty During the initial use fill the salt reservoir with 1 litre of water prior to filling it with salt G Some water might have remained in the product due to the quality control processes in the production It is not harmful for the product Disposing of packaging material Packaging materials are dangerous to children Keep packaging materials in a safe place away from reach of the children Packaging materials of the product are manufactured from recyclable materials Dispose of them properly and sor
32. portation of the product 10 Disposing of the old product 10 4 Prewashing 11 Tips for energy saving 11 Water softening system 11 Adjusting the water softening system 11 Adding salt 12 Detergent 13 Adding detergent 13 Tablet detergents 14 Rinse aid 15 Silverware basket 18 Silverware basket piece 18 Movable silverware basket 18 Collapsable lower basket wires 2 pieces 19 Collapsable lower basket wires 4 pieces 19 Lower basket bottle wire 19 Lower basket multipurpose height adjustable service rack 20 Upper basket height adjustable rack 20 Upper basket drawer 21 Upper basket glass support piece 21 Collapsable upper basket wires 21 Collapsable upper basket wires 22 Adjusting the height of loaded upper basket 22 Adjusting the height of loaded upper basket 23 Adjusting the height of empty upper basket 24 5 Operating the product 25 Keys 26 Preparing the machine 26 Programme selection 27 Adding an auxiliary function to the programme 27 Setting Time Delay function 27 Starting the programme 27 Child Lock 28 Programme follow up 28 Canceling a programme 28 Salt indicator 29 Rinse Aid indicator 29 End of programme 29 6 Maintenance and cleaning 31 Cleaning the outer surface of the product31 Cleaning the interior of the machine 31 Cleaning the filters 31 Cleaning the hose filter 32 Cleaning the impellers 32 7 Troubleshooting 34 El Dishwasher Overview 13 12 11 10 1 Tabletop depen
33. r when you start the product Therefore add the softening salt before starting the machine First take the lower basket out to add softening salt Turn the salt reservoir lid in counter clockwise to open it A B Before initial use fill the water softening system with 1 litre of water C Fill the salt reservoir with salt by using salt funnel D To speed up dissolution rate of salt in water stir it with a spoon You can put about 2 kg of softening salt into the salt reservoir Replace the lid and tighten it securely when the reservoir is full 12 EN 5 If you will not start a washing programme immediately after adding the salt run the machine empty in the shortest programme to dissolve and wash away the scattered salt in the machine GJ Since different salt brands in the market have different particle sizes and since the water hardness may vary dissolution of the salt in water may take a couple of hours Therefore Salt Indicator remains on for a while after adding salt into the machine Detergent You can use powder or tablet detergent in the machine G Only use in the machine the detergents produced particularly for use with dishwashers We recommend you not to use detergents that contain chlorine and phosphate as they are harmful for the environment G Contact the detergent producer if the dishes are wet and or if you notice limescale spots particular
34. rienced people including children unless they are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product Children s safety Electrical products are dangerous for the children Keep children away from the product when it is in use Do not let them to tamper with the product Do not forget to close the door of the product when leaving the room where it is located Store all detergents and additives in a safe place away from the reach of the children 6 EN EI Installation Refer to the nearest Authorised Service Agent for installation of your product To make the product ready for use make sure that the electricity tap water supply and water drainage systems are appropriate before calling the Authorised Service Agent If they are not call a qualified technician and plumber to have any necessary arrangements carried out GJ Preparation of the location and electrical tap water and waste water installations at the place of installation is under customer s responsibility Installation and electrical connections must be carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products cause risks for your safety Make sur
35. se 1oj uutuue1B5oid 390U213J Y y suonipuoo jeogoesd 1 pun inooo 21042194 ABW s Su Jz jjiq suonipuoo piepue s JOPUN PSUILUJA Ep 919M lq y u UMOYS s njea uodwnsuo y puq A Mg pug pug A A A asuly JOH sury JOH Aq Aq A A A A suondo ynoyym asuly JOH asuly JOH asuly JOH 9suly JOH pug aouanbas uuue1Boid A A A A A suu POD suu POD SULI ploO sul ploO asuly JOH A A A A A Buljlos Jo unowe y use use yseMm yseMm suu pjo pug o p lsn pe s 2u nb s A A A A A A uuuue16oid u 1 ySem ld ySem ld ySem ld ySem ld yseMm ySem ld eld G q W9 G W9 GZ W v oo a Ha ow oew v o Swebiejed yoyseq s usip JaMo By u Ajjnamod dnpjing sopo Jo sadfj e 10 ajqeying paysem ase sued pue sjod s usip peq y Bunu A id Aypeoyewoyne awg Buiysem ay jym yayseq seddn pallos AjAeay JO AEM 1s 1se BU u Joy snu pue s ep ay SE M se JayeM ay u j a su s paysem jqeyns osjy s iqeq p ue o ae BunieA Bune 1d y M e JO BUIYDeW Bulysem y Jo junowe aue sjisuajn jes pue 104 s lonie se yons 1d y ale Jey s ys p ae zey s usip Ajlep paueajo aid au u BunieA 1d y aq pue ainjejedwa y sjas ssejg s usip jrep au u IB u enx sued pue p lios wnipew y p lios wni p w ay 10 padesos sme yey m ey s usip pajos pue saysip y jo u6 p jo imeu paxiw y Jo Jeuinbay yorum saysip sjod saysip p llos yorym ze wesBoud 10 wesGoid B
36. sket wires depends on the model There are foldable wires on the upper basket of the machine that you can lay down when you need larger space for big dishes To bring the collapsable wires into horizontal position grab the first collapsable wire and push it in direction A or B Place your larger dishes into the area created To bring the wires back to vertical position just lift them up Collapsable wires will click into the latch again HI 21 EN Collapsable upper basket of the loaded basket in up or down wires directions without removing it from the depends on the model machine To bring the collapsable wires on the f upper basket of the machine into To raise the basket horizontal position press on the latch 1 Grab one of the upper basket wires right or left and lift it up A 1 Place your larger dishes into the area created 2 To bring the wires 2 Repeat the same process to raise back to vertical position just lift them the other side of the basket up 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up To lower the basket 1 Press the latch on the basket adjustment mechanism right or left to lower the basket B Adjusting the height of loaded upper basket depends on the model Basket adjustment mechanism on the upper basket of the machine is
37. ss dishwasher standardloading com Do not forget to provide the code stock and serial numbers of the product to be tested in your request e mail along with your contact information Code stock and serial numbers of the product is located on the type label attached to the side of the door 4 EN 2 Important safety instructions This section contains safety instructions that will help to get protected from risk of personal injury or property damage Failure to follow these instructions shall void all warranties General safety Never place the product on a carpet covered floor otherwise lack of airflow beneath the product will cause electrical parts to overheat This will cause problems with your product Do not operate the product if the power cable plug is damaged Call the Authorised Service Agent Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Do not neglect to have the grounding installation made by a qualified electrician Manufacturer shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations The water supply and draining hoses must be securely fastened and remain undamaged Unplug the product when not in use Never wash the product by spreading or pouring water onto it There is the risk of electric shock Never touch the plug with wet hands
38. ss setting If your supply water is soft lt 5 dH do not use salt Choose programmes that wash in higher temperatures e g 60 65 C You can also use glass protective detergents that are commercially available Foam forms in the machine Dishes are washed with hand wash detergent by hand but not rinsed before placing them into the machine gt gt gt Hand wash detergents do not contain antifoam There is no need to hand wash the dishes before placing them into the machine Removing the coarse soil on the dishes under tap water with a tissue paper or fork will be sufficient Rinse aid has spilled into the machine when adding rinse aid gt gt gt Take care that rinse aid is not spilled in the machine when you are filling it Clean any spilled rinse ait with the help of a tissue paper towel Lid of the rinse aid reservoir is left open gt gt gt Make sure that the lid of the rinse aid reservoir is closed after adding rinse aid Kitchen utensils are broken Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Water remains in the dishwasher at the end of the programme Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Discharge hose is clogged blocked gt gt gt C
39. t in accordance with recycled waste instructions Do not dispose of them with normal domestic waste Transportation of the product A If you need to move the product do it in upright position and hold from the rear side Slanting the product onto its front side may cause the electronic parts in it get wet and damaged 1 Unplug the product before transporting it 2 Remove water drainage and water supply connections 3 Drain the remaining water in the product completely Disposing of the old product Dispose of the old product in Ke an environmentally friendly manner Some parts of the m product are manufactured from recyclable materials Along with a recycling symbol information about its nature PE PS POM etc is also provided on the material These materials should not be disposed as normal domestic wastes Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your product A For children s safety cut the power cable and break the locking mechanism of the door so that it will be non functional before disposing of the product 10 EN EJ Prewashing Tips for energy saving Following information will help you use the product in an ecological and energy efficient manner e Wipe away any coarse food remnants on the dishes before putting them in the product e Operate the product after filling it completely e When selecting a programme refer to the
40. tion is selected Time Delay key It is used to select the Time Delay function You can delay the start of the selected programme up to 24 hours with increments of 30 minutes thanks to the Time Delay function Express key This option allows you to shorten the selected programme the dishwasher then uses higher water pressure and consumes less energy and water Preparing the machine 1 Open the tap Plug in to the socket Open the door of the dishwasher Place the dishes in accordance with the instructions in the user manual 5 Make sure that the upper and lower impellers rotate freely 6 Put adequate amount of detergent into the detergent dispenser 7 Check if the Salt and Rinse Aid indicators light and add salt and or rinse aid if needed 8 Close the door of the dishwasher N 26 EN Programme selection 1 Press On Off key to turn on your machine 2 Refer to Table of Programme Data and Average Consumption Values to select a washing programme suitable for your dishes 3 Press Programme Selection key P repeatedly until the number of the selected programme appears on the Programme indicator ely eles Programme number will increase by one each time you press the key GJ Number of the programmes on the machine may change depending on the model you have purchased Adding an auxiliary function to the programme Depending on your needs you can add Half Load 1 2 Tablet Detergent E
41. uiuseA s usip ltep pajios y uo sjueuuu i y BHuljios y seuluuajaq wesBoid jqeyns jsaq ayL y 104 jqeyns paeay JO jqeyns Buiysem Ajleq Jeo1wouoss soy Any 104 lqelns 6uiAouu 104 ajqeyng Builios jo 1 5 q us S u S l o s ss s El jqe suweibojg 30 EN 6 Maintenance and cleaning Service life of the product extends and 1 Turn the micro filter 3 and frequently faced problems decrease if it coarse filter 2 assembly counter is cleaned at regular intervals clockwise and pull it out from its A Unplug the product and turn off the seating A tap before attempting any cleaning procedures G Do not use abrasive substances for cleaning GJ Clean the filters and impellers at least once a week Cleaning the outer surface of the product Clean the outer surface and door gaskets of the product gently with a mild cleaning material and damp cloth Wipe the control panel only with a damp cloth Cleaning the interior of the machine e Clean the interior of the machine and the tank by running a prewash programme without detergent or a long washing programme with detergent based on the degree of soiling e If water has remained in the machine drain the water by performing the procedures under the topic Canceling a programme If the water cannot be discharged clean any leftover deposits that have piled up in the bottom of the machine blocking the water path Cleaning the f
42. wer basket wires spaces by folding each wire individually 2 pieces or all of them at once Lay the foldable depends on the model wires down by pressing on the latch The two piece foldable wires located A at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc 1 2 You can create larger spaces by folding each wire individually or all of them at once Lay the foldable wires down by pressing on the latch A Lower basket bottle wire depends on the model The bottle wire is designed for easier washing of long pieces with wide mouths You may take out the bottle wire from the basket when not in use by pulling it out from both sides H Collapsable lower basket wires 4 pieces depends on the model The four piece foldable wires located at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc 1 2 3 4 You can create larger Lower basket multipurpose height adjustable service rack depends on the model This accessory located at the lower basket of the machine allows you to easily wash pieces such as extra glasses long ladles and bread knives a gt Sinan Min Kf SS Veto To close the racks 1 Fold the rack A 2 Slide the rack up B 3 Put the rack in vertical
43. xpress and Time Delay functions to the programme you have selected Press the key of the function you wish to add Indicator of the relevant function will appear on the display Setting Time Delay function If an economical electricity tariff is applied in your region you can use the Time Delay function to wash your dishes during appropriate hours 1 Press the Time Delay function key after selecting the washing programme and other auxiliary functions Time Delay indicator 3 will start flashing on the display 2 Press Time Delay key to set the time you wish Time will increase with increments of 30 minutes up to 24 hours every time you press the key 3 Press Start Pause Cancel key Delay time will start countdown 27 Time Delay indicator 8 and Start Pause indicator will light continuously Remaining time will appear on the Time Delay indicator Programme will start automatically when the countdown is over Changing the settings during Time Delay While the Time Delay function is activated you can make changes in the washing programme other auxiliary functions or the delay time 1 Press Start Pause Cancel key to switch the machine into Pause mode Countdown will stop 2 Select the new programme auxiliary functions and time as described in the sections above 3 Press Start Pause Cancel key Countdown will resume or restart Canceling the Time Delay function 1 Press and hold Start
Download Pdf Manuals
Related Search