QNAP REXP-1200U-RP storage enclosure
Contents
1. K 1 Za E QNAP RAID Expansion Enclosure Hardware User Manual 2012 Systems Inc Rights Reserved Thank you for choosing products This user manual provides description of the hardware of the QNAP RAID expansion enclosure and relevant guideline of certain functions Please read carefully and strictly adhere to the instructions of the manual This user manual is applicable to the following RAID expansion enclosure s REXP 1200U RP REXP 1600U RP Note The product you purchased may not support certain functions dedicated to specific models All features functionality and other product specifications are subject to change without prior notice or obligation Information presented is subject to change without notice No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means mechanical electronic photocopying recording or otherwise without prior written permission of QNAP Systems Inc and the logo are registered trademarks of Systems Inc Other products and company names mentioned herein may be the trademarks of their respective companies DISCLAIMER In no event shall the liability of QNAP Systems Inc QNAP exceed the price paid for the product from direct indirect special incidental or consequential software or its documentation QNAP makes no warranty or repres2. Do not place the RAID expansion enclosure on any uneven surface to avoid falling off and damage Make sure the voltage is correct in the location where the RAID expansion enclosure is installed Contact the distributor or the local power supply company for the information Do not place any object on the power cord Do not attempt to repair the RAID expansion enclosure in any occasions Improper disassembly of the product may expose the users to electric shock or other risks For any enquiries please contact the distributor The RAID expansion enclosure should only be installed in the server room and maintained by the authorized server manager or IT administrator The server room is locked by key or keycard access and only certified staff is allowed to enter the server room A Warning Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions Do NOT touch the fan inside the RAID expansion enclosure to avoid serious injuries The RAID expansion enclosure is heavy and should be installed into a rack by two people To avoid personal injury and or damage to the equipment do not attempt to lift and install the enclosure into a rack without a mechanical lift and or help from another person Before You Start The RAID expansion enclosures can ONLY be used with the QNAP Turbo NAS Ins
3. 5mm L 1 2 SET J 2 pH Jj ac 3 0 E cos cen f Come f cer n mm Q 500mm 650mm 850mm 0 C 2 The optional rack kits for the rackmount RAID expansion enclosure are only compatible with square hole server racks OQ X L 9 a D Table 2 RAID Expansion Enclosure Hardware Specification 12 3 RAID Expansion Enclosure Hardware Illustration D Caution Modifying the hardware software or firmware of the QNAP products will void the warranty QNAP is not responsible for any form of damage or loss of data caused by modding the QNAP products Users should bear their own risks of all sorts of possible data loss or system instabilities due to changing the hardware parts modifying the default system firmware or installing any unauthorized third party applications on the QNAP products 3 1 Front view REXP 1600U RP LED Indicators System status system fault system over heat fan error 13 D Caution Always turn on the RAID expansion enclosure before turning on the attached NAS Always shut down the NAS before turning off the RAID expansion enclosure 14 wo oen 000 mesmenkof Amber Amber System fault detected overheat fan d System Fault error power supply unit fails or is plugged out etc o _____ Nofaulthas occured Amber The system overheat No faul
4. INS TRUCTIONS 22 5 a 18 42 L MINLSAS CABLBREMONVALD EE EE E 19 5 REMOVE AN AIR DUCT APPLIED TO 16000 20 DG INSTALI JREMOVEA FAN MODULE ear oro areas Pet era 21 Oc INSPIAEEALPANMODU EB pasce etus e tmu D EU MM d a 21 6 25 j REMOVEA FAN ENEE 21 ANSTALE POWER SUPPLY UNI eege 22 TECHNICAL SUP POR DE KE 24 Safety Warnings 10 11 12 The RAID expansion enclosure can operate normally in the temperature of 09C 409C and relative humidity of 0 60 Please make sure the environment is well ventilated The power cord and devices connected to the RAID expansion enclosure must provide correct supply voltage 100 240V AC 50 60Hz Do not place the RAID expansion enclosure in direct sunlight or near chemicals Make sure the temperature and humidity of the environment are in optimized level Unplug the power cord and all connected cables before cleaning Wipe the RAID expansion enclosure with a dry towel Do not use chemical or aerosol to clean the RAID expansion enclosure Do not place any objects on the RAID expansion enclosure for the server s normal operation and to avoid overheat Use the flat head screws in the product package to lock the hard disks in the RAID expansion enclosure when installing hard disks for proper operation Do not place the RAID expansion enclosure near any liquid
5. RP Connect the storage expansion port on the QNAP NAS to the IN ee port of a REXP 1200U RP using the external Mini SAS cable SFF 8088 Note Optional storage expansion card is required on the QNAP NAS Connect the REXP 1200U RP to another REXP 1200U RP Connect Mini SAS cable SFF 8088 from the OUT port of the REXP 1200U RP to the IN ee port of another REXP 1200U RP D Caution Do not connect an OUT port to another OUT port or an IN port ee to another IN port ee 18 4 2 Mini SAS Cable Removal Follow the steps below to remove the Mini SAS cable 1 Pull up the restraining clip latch of the Mini SAS cable 2 Remove the Mini SAS cable from its restraining clip Ps i 4 vu a 19 5 Remove Air Duct Applied to REXP 1600U RP Unlatch the air duct with your thumb and index finger Pull the air duct upward to disengage it from the RAID expansion enclosure 20 6 Install Remove a Fan Module 6 1 Install a Fan Module Insert a fan module into the fan slot until the fan module is fully seated A Warning Replace the fan module within 3 minutes to avoid system overheat Do not attempt to operate the system without fan module 6 2 Remove a Fan Module Remove the fan module by grasping and pulling up the fan module from the fan slot 21 7 Install Power Supply Unit A Warning The RAID expansion enclosure supports replacing the redun
6. an error Rear panel SAS link SAS error enclosure ID 2U rackmount 3U rackmount Dimensions 88 H x 439 W x 520 D mm 130 H x 442 4 W x 528 3 D mm 3 46 H x 17 28 W x 20 47 D 5 12 H x 17 42 W x 20 80 D inch inch Weight Net weight 14 8 kg 32 63 Ib Net weight 18 14 kg 39 99 Ib Gross weight 21 99 kg 48 48 ID Gross weight 25 92 kg 57 14 Ib Sound Level Standby 43 3 dB Standby 30 1 dB In operation 44 1 dB In operation 41 5 dB with 12 x 1TB hard drive installed with 16 x 1TB hard drive installed Power Idle mode 105W Idle mode 199W Consumption In operation 147W In operation 289W with 12 x 500GB hard with 16 x WD WDCWD20EVDS drive installed 2TB hard drive installed Relative 0 60 Humidity Power SUPPIY Input 100 240V 50 60Hz Output 600W COM port Reserved for system maintenance Fan 3 x 6 cm smart cooling fan Management Supports disk S M A R T information via NAS RAID expansion enclosure identifier Locate RAID expansion enclosures Locate hard disks on RAID expansion enclosures Smart fan control In band SAS firmware update Remark The rackmount RAID expansion enclosure complies with ANSI EIA RS 310 D rack mounting standards Before purchasing the server racks for this model please make sure the server racks conform to the following criteria 1 Rack size a Mounting post width gt 450mm b Panel width 2 500mm c Mounting post depth 650mm 850mm 46
7. dant power supply unit without turning off the enclosure when redundant power supply mode is enabled However users are strongly recommended to turn OFF the RAID expansion enclosure before replacing the power supply unit to reduce the risk of electric shock To replace a failed power supply unit follow the steps below 1 Turn off the RAID expansion enclosure 2 Hold the black handler and press and hold the green button firmly 22 3 Unplug the failed power supply 4 Plug in a new power supply 5 Turn on the RAID expansion enclosure 23 Technical Support QNAP provides dedicated online support and customer service via instant messenger Online Support http www gnap com MSN g support hotmail com Skype qnapskype Forum http forum qnap com Technical Support in the U S and Canada Email Ssupportus qnap com TEL 909 595 2819 Address 166 University Parkway Pomona CA 91768 4300 Service Hours 08 00 17 00 GMT 08 00 Pacific Time Monday to Friday 24
8. entation expressed implied or statutory with respect to its products or the contents or use of this documentation and all accompanying software and specifically disclaims its quality performance merchantability or fitness for any particular purpose QNAP reserves the right to revise or update its products software or documentation without obligation to notify any individual or entity Note e Back up your system periodically to avoid any potential data loss disclaims any responsibility of all sorts of data loss or recovery Should you return any components of the RAID expansion enclosure package for refund or maintenance make sure they are carefully packed for shipping Any form of damages due to improper packaging will not be compensated Regulatory Notice FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by tur
9. ning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Shielded interface cables if any must be used in order to comply with the emission limits 4 Class B only Symbols in this document Warning D Caution This icon indicates the instructions must be strictly followed Failure to do so could result in injury to human body or death This icon indicates the action may lead to disk clearance or loss OR failure to follow the instructions could result in data damage disk damage or product damage Contents CONTENTS LEE 6 SAFETY Ae 7 BEFORE YOUSTART EEN 9 I PACKAGE CONTEN KEE 9 2 HARDWARE SPECIFICATION 11 3 RAID EXPANSION ENCLOSURE HARDWARE ILLUSTRATION 13 S EE Hur re 13 mal c 16 4 CABLE THE SYSTEM 18 Zl KCABLING
10. t has occurred 8 System over Heat Fi Se Fan Error No fault has occurred Hard Drive Red Green Flashes red The disk data is being accessed and a read write error occurred during the process A hard disk drive read write error WEN RN Flashes The disk data is being accessed __ The hard disk drive is ready Table 3 Description of RAID Expansion Enclosure LEDs 15 3 2 Rear view REXP 1200U RP REXP 1600U RP COM Port Reserved IN Port 3 IN OUT Port Status LED NE I GENE mwerComedon 16 Link Fault Amber Amber Port linked but without all four lanes Flash amber SAS cabling error Off No fault has occurred Table 4 RAID Expansion Enclosure IN OUT Port Status LEDs 17 4 Cable the System 4 1 Cabling Instructions An example of connecting a QNAP NAS to four REXP 1200U RP enclosures is shown below Turbo NAS lt Wo 12 1 se SS 909 S lt DHTH DAN d EE a af 2 9 0 8 ef 729 5 3 ata G E es Storage expansion ports REXP 1200U RP REXP 1200U RP_ Connect the QNAP NAS to the REXP 1200U RP If two or above REXP 1200U RP enclosures are configured connect the two storage expansion ports on the NAS to two REXP 1200U RP enclosures for maximized performance Connect the QNAP NAS to the REXP 1200U
11. tall the hard drives in sequential order following the tray number The RAID expansion enclosures are applicable to the TS x79 series Turbo NAS Always turn on the RAID expansion enclosures before turning on the attached NAS WN Always shut down the NAS before turning off the RAID expansion enclosures 1 Package Contents The product package contains the following items REXP 1200U RP or REXP 1600U RP Screw pack 6565696565 65 65 65 6565656565 65 25 AN 656565 45 45 68 65 65 Way E Woy Quick Installation Guide 0 5m Mini SAS cable Hardware Installation CD Rail kit optional purchase Storage expansion optional purchase Table 1 Package Contents 10 2 Hardware Specification The physical specifications operating environment and power requirements of the RAID expansion enclosure are listed below Lu wan OF ee REXP 1200U RP REXP 1600U RP Host Interface Two SAS 4x wide port Two SAS 4x wide port IN port OUT port 0 000 port OUT port Hard Drive 12 x 3 5 inch SAS SATA 6Gb s 16 x 3 5 inch SAS SATA 6Gb s SAS SATA 3Gb s hard drive or SAS SATA 3Gb s hard drive or 2 5 inch SAS SATA SSD hard drive 2 5 inch SAS SATA SSD hard drive Note The standard system is shipped without hard drives For the hard drive compatibility list please visit htt www qnap com pro compatibility as LED Indicators Front panel Status fault system over heat f
Download Pdf Manuals
Related Search