Chief K4G210B flat panel desk mount
Contents
1. Figure 6 14 Use two 3 8 16 x 2 3 4 socket head carriage screws A1 and two 3 8 lock nuts A2 to secure left array arm X and right array arm Y to array center AA or BB See Figure 7 K4G210 shown 14 D YA x2 Figure 7 15 Hang array center AA or BB onto column arm 2 faceplate See Figure 8 K4G210 shown mounting tab Figure 8 16 Use two 10 32 x 3 8 button head cap screws D2 to secure column arm Z to array center AA or BB See Figure 9 K4G210 310 Installation Instructions K4G210 shown Figure 9 17 K4G310 only Insert two channel attachments J into back of array center BB Attachments must be turned horizontally in order to fit into channel See Figure 10 NOTE Channel attachments are already pre installed on K4G210 Proceed ahead to step 20 if installing K4G210 Figure 10 18 K4G310 only Rotate channel attachments J 90 clockwise See Figure 11 19 K4G310 only Slide channel attachments J toward arm assembly Z to prepare for handle installation See Figure 11 20 Use two 10 32 x 1 2 Phillips pan machine screws D1 and two handle clamps G to secure handle H to array center AA or BB See Figure 12 K4G310 shown Figure 12 Display Installation WARNING Excee2. VA 15 28 TLTADJ USIMENT F TLTADJ USMENT TADJ 2 NJA 388 2 76 2 3 00 a 3 75 95 3 4 94 1 2 27 57 6 125 5 71 7 74 0 MAX 180 7 196 7 SURFACE eer DEPTH K4G310 16 20 mmm 48 36 4115 1816 TF 1228 4 EXTENSON MAX DISTANCE TLTADJ USIMENT DXT E 2 a an S INTERFAC ES E Ni E 0 o 386 6 i __ Ur TLTADJ USTMENT E JLTADI USIMENT 3 00 76 2 F ni 13 34 2 75 75 95 3 SU T 2 27 TI 57 6 4 94 7 11 S E 125 5 180 7 MAX 7 74 SURFACE 196 7 DEPTH K4G210 310 Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien
3. E1 x2 Figure 25 12 Installation Instructions K4G210 310 13 K4G210 310 Installation Instructions 14 Installation Instructions K4G210 310 15 K4G210 310 Installation Instructions G CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002371 Rev02 2013 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 06 13 USA International Europe Asia Pacific lt lt lt gt TI U 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 Pa LD d D S
4. Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a mao A mano Met de hand A la main Optional Opcional Optional Opcional Opzionale Optie En option C d y n 1 2 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale O Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranga Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions K4G210 310 TOOLS REQUIRED FOR INSTALLATION e in 1 2 IW Ne mup AND up 5 16
5. included 2 RRR RRA i i f i 1 d i I 3 16 included 5 32 included 1 8 included Hardware bag en SSS parts numbered on Ki O Cie bag as shown s Os g Ge G 2 pa hi Bei B1 2 B2 2 handle clamp 3 8 16 x 2 3 4 3 8 1 4 20 x 1 2 1 4 s C 4 a See E ei E1 4 2 4 Fi 1 F2 1 F3 1 F4 1 LI tie mount 10 24 3 8 1 8 5 32 H 1 12 for K4G310 handle 3 16 5 16 J 2 K4G310 only L 1 channel attachment column cap base cover M 8 12 N 8 12 Panz Rena M4x30mm M4x20mm Max12mm a a 3 4 SE MS 8 W 6 bumper U 1 cable management cover grommet screw and base grommet plate Z 1 column arm K4G210 center CC 1 K4G310 center column K4G210 310 Installation Instructions Assembly And Installation 1 Use four 1 4 20 x 1 1 4 flat head cap screws C to secure grommet plate U to column CC Make sure longer legs of grommet plate are aligned with the front of column See Figure 1 front of column Figure 1 2 Apply bumpers W to underside of grommet plate U See Figure 2 Figure 2 3 Locate a flat surface thickness minimum of 1 to maximum of 5 on which to mount the array assembly 4 If ahole doesn t already exist drill a hole in desk with a diameter between 1 2 a
6. 17 10 Figure 17 Pivot Adjustment Column Arm 1 Use handle to extend or collapse column arm Z as desired See Figure 18 2 Optional Loosen or tighten column arm pivot tension screws as desired to increase or decrease pivot tension See Figure 18 pivot tension screws arm collapsed Figure 18 Height Adjustment 1 Loosen 1 4 20 1 2 socket head carriage screws B1 holding column arm Z to column CC See Figure 19 2 Adjust column arm to desired height See Figure 19 3 Tighten 1 4 20 x 1 2 socket head carriage screws B1 to lock column arm s position See Figure 19 9 9 Figure 9 Installation Instructions K4G210 310 Faceplate Assembly Removal 1 Remove hex head bolt from bottom of faceplate assembly See Figure 20 2 Slide out removable plate from bottom of faceplate assembly See Figure 20 removable plate Figure 20 3 Remove faceplate assembly from array arm See Figure 20 To Reattach Faceplate Assembly 4 Place faceplate assembly on array arm at desired mounting position See Figure 21 5 Slide removable plate back into slot at bottom of faceplate assembly See Figure 21 6 Reinstall hex head bolt removed in Step 1 to secure faceplate assembly to array arm See Figure 21 removable plate Lateral
7. display Proper screws will easily and completely thread into display mounting holes 3 Using Phillips screwdriver carefully install two selected screws N or M through selected spacers Q or R into the upper mounting holes on the display Thread screws completely into display then back out 3 complete turns See Figure 15 4 Pick up and align display so that screws N or M installed on the back of the display in the previous step fit into the mounting holes on the faceplate Lower the display firmly into place See Figure 15 faceplate array arm not shown for clarity _ Figure 15 K4G210 310 Installation Instructions g Slide two remaining selected spacers Q or R in between faceplate and display positioning them over the lower two mounting holes See Figure 16 Install two remaining selected screws N or M through lowertwo mounting holes on faceplate selected spacers Q or R into the ower mounting holes on the display See Figure 16 faceplate array arm not shown for clarity 7 Figure 16 Tighten all four screws Do not over tighten Adjustments Pivot Adjustment Array Arm 1 Array arms may pivot toward the front of mount up to 20 per arm See Figure 17 When arms are at desired pivot position lock pivot position by tightening 3 8 16 x 2 3 4 socket head carriage screws A1 using 5 16 hex key E5 See Figure
8. INSTALLATION INSTRUCTIONS Kontour Articulating Array Arm Grommet Series CHIEF K4G210 310 Our Mounts Your Vision K4G210 310 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factor
9. Shift Loosen knob on top of faceplate assembly until faceplate can slide freely along array See Figure 22 Adjust lateral position as desired See Figure 22 Tighten knob to secure lateral position See Figure 22 Figure 22 Pitch Roll Yaw Adjustment Loosen knob on top of faceplate assembly See Figure 23 Adjust pitch roll and or yaw as desired See Figure 23 Tighten knob to secure desired faceplate position See Figure 23 Figure 21 Figure 23 11 K4G210 310 Installation Instructions Cable Management 3 Route cables along mounting arms See Figure 26 1 Route cables from display through cable management 4 Use cable ties not included to secure cables to tie clips covers V as desired See Figure 24 E1 See Figure 26 2 Install cable management covers V onto array arms X NOTE Leave enough slack in the cables so that arm may still and Y See Figure 24 swing without resistance from the cables K4G210 shown as example Oaie ties not included Figure 26 Figure 24 Cable Management Clips 1 Use two 10 24 x 3 8 button head cap screws E2 to attach two tie mounts E1 to upper mounting arm See Figure 25 2 Use two 10 24 x 3 8 button head cap screws E2 to attach two tie mounts E1 to lower mounting arm See Figure 25 0 E2 x 2 gt
10. ding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located on the K4G210 310 Series mounts up to and including the display does not exceed 15 Ibs 6 8 kg per display CAUTION Using screws of improper size may damage your display Proper screws will easily thread into display mounting holes NOTE Supplied screws M N and P may not fit properly for all displays See display s operating instructions for details IMPORTANT When applicable always install center display FIRST in order to prevent stand from tipping If there is no center faceplate K4G210 be sure to support opposite arm when mounting displays to prevent stand from tipping If possible mount displays to both sides simultaneously NOTE Set height of center display prior to installing other displays See Height Adjustment Section for details Center of display must be at least 18 above desk surface Installation Instructions K4G210 310 Flush Mounting Holes 1 Position faceplate in desired mounting position Adjust as required before proceeding See Height Adjustment Section for details 2 Using Phillips screwdriver carefully install two M4 x 12mm Phillips pan machine screws P into the upper mounting holes on the display Thread screws completely into display then back out 3 complete turns See Figure 13 facep
11. late array arm not shown for clarity Figure 13 3 Pickup and align display so that screws P installed on the back of the display in the previous step fit into the mounting holes on the faceplate Lower the display firmly into place See Figure 13 4 Using Phillips screwdriver install two M4x12 mm Phillips pan machine screws P through the lower mounting holes on faceplate into the display See Figure 14 faceplate array arm not shown for clarity Figure 14 5 Tighten all four screws P Do not over tighten NOTE If roll adjustment is desired for center faceplate do not tighten screws 6 Repeat Steps 1 5 for other displays 7 Proceed to Cable Management Section Recessed Mounting Holes NOTE If faceplate does not fit into recessed area of display proceed with the steps in this section 1 Determine depth of recessed mounting holes relative to back surface of display against which faceplate will contact 2 Select proper length spacer and screw from table below NOTE All spacers used should be the same length If the recess depths result in multiple spacer lengths then select the longer spacer AND screw N M4 x 20mm M M4 x 30mm IF recess DEPTH is THEN use spacer Q 3 8 long R 3 4 long 3 8 or less More than 3 8 up to and including 3 4 CAUTION Using screws of improper size may damage your
12. nd 3 1 2 at desired mounting location See Figure 3 5 Position mount on desk so that center hole of grommet plate U is centered over grommet hole See Figure 3 Insert grommet screw T through grommet hole and thread into center hole of grommet plate U See Figure 3 Tighten grommet screw T until grommet base is tightened against underside of desk and mount is securely mounted to desk See Figure 3 diameter between 1 2 and 3 1 2 Figure 3 Carefully manipulate base cover L to create an opening large enough to wrap cover around array column See Figure 4 Wrap base cover L around column and slide it down until base cover fits securely onto grommet plate U See Figure 4 Figure 4 Installation Instructions K4G210 310 10 Loosely install two 1 4 20 x 1 2 socket head carriage screws B1 through mounting holes on column arm Z bracket and into 1 4 square nuts B2 See Figure 5 11 Slide column arm Z bracket into column CC until desired mounting height is reached See Figure 5 B2 x 2 CC Figure 5 12 Tighten two 1 4 20 x 1 2 socket head carriage screws B1 to secure column arm Z at desired height See Figure 6 13 Install column cap K to column CC See Figure 6
13. y warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located on the K4G210 310 mounts up to and including the display does not exceed 15 lbs 6 8 kg per display WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS Installation Instructions K4G210 310 DIMENSIONS K4G210 20 MAX ANGLE 37 13 943 2 MAX DISTANCE VESA 100 X 100 75X75 COMPATIBLE Jr ek INTERFACES
Download Pdf Manuals
Related Search