Miele B 1847
Contents
1. 25 Switching on Selecting the temperature for ironing The temperature selector on the iron is used for setting the ironing temperature The temperature settings are indicated by dots around the selector These dots correspond to the international symbols for ironing The yellow indicator light comes on while the iron is heating up 26 Material Dot Temperature symbol range Minimum iron e Low Synthetics temperature Woollens ee Medium Silks temperature Linen eee High Cottons temperature m Use the temperature selector to set the temperature required The indicator lights up yellow while the iron is heating up When the set temperature is reached the indicator light goes out The iron is ready Steam can be used in the temperature ranges between ee and eee Please note that the steam must be ready for steam ironing Steam readiness is indicated when the C5 indicator light lights up on the control panel In the temperature range the temperature of the iron sole plate is too low for steam ironing Do not use the steam button on the iron This will result in spitting from the steam jets After increasing the temperature to at least you must wait until the heating up phase is completed before using the steam button Switching on Tip Sorting the laundry Sort your laundry according to heat sensitivity for efficient ironing Iron the most sen2. L Viele Operating instructions Fashion Master steam ironing system B 1312 B 1826 B 1847 To avoid the risk of accidents or en GB damage to the appliance it is essential to read these instructions before it is installed set up and used for the first time M Nr 09 370 090 Contents Guide to the appliance iles 4 Warning and Safety Instructions 6 Caring for our environment 12 Disposal of your old appliance s ceesre arr ER a ee 12 Moving the Fashion Master 0 0 0000 13 ASSEMDIING lt coe mex Ron hr on eau e PAR cera e ath qned pon 14 Adjdstngthedelglhtus iaa ced sine e n ede ea C m e dei pele 16 Connection 1e 22 ag aie al ba Ped exa Re pelas ed dg EO Ran d e 17 Before using for the first time 2 cc con iles 20 Water hardness suddetto ee hen 20 Setting the water hardness level ilii esee 22 Checking the programmed water hardness level aaa 22 Switching On 2 244 244 222 344 REPRE dae er eq ren 23 Switching on the Fashion Master liiis 23 Filing the water Container uec ie e mex exper rn 23 WATS gual e ee a ears tee yt E a ee lee 25 CoolDown function anenee ae ea s 25 Auto Off TUNGOR esse e Rer Rieder ernennt 25 Selecting the temperature for ironing ii eee 26 Ironihig edu rem aet eru a SR PARI AULA at en eh eee ee aioe 28 F n deba ae ae en Ec qo Ue eR E eee aes eds 28 koning with Steam ues Leto e d dece Rene 29 ro
3. Remedy The ironing table is not heating Steam has not been used for a while Operate the steam button 2 to activate the ironing table heating The steamer is connected to the tower The ironing table does not heat up when the steamer is connected The appliance is damaged Call Miele Service The iron always heats to a high temperature There is a fault with the appliance Call Miele Service The ironing table cover is damp There is a fault with the appliance Remove the ironing table cover and allow it to dry Replace the ironing table cover see Replacing the ironing table cover If the ironing cover seems damp again call Miele Service 52 Problem solving guide Problem Possible cause Remedy The fan is not running No steam is required The fan only runs when the steam function on the iron is operated The steam is not ready Wait until the 2 indicator light signals that steam is ready The water container is empty or missing Fill the water container with fresh tap water and insert it into the appliance The steamer is connected The fan only runs when the iron is connected Connect the iron There is a fault with the appliance Call Miele Service Descaling cannot be started although the indicator light S is flashing or lit up The iron or steamer are plugged in Disconn
4. Set the appliance to its highest working position see Adjusting the height to allow access for removing the residual water container m Remove and empty the residual water container m Replace the residual water container The amp indicator light will go out Later on in the descaling process the residual water container must not be removed unless the G indicator light comes on Otherwise hot water could spill out and cause injuries and or damage to the appliance 41 Cleaning and care If the appliance is still hot from the last use the s indicator light comes on The descaling process is automatically resumed when the appliance has cooled down and the x indicator light has gone out The 4 indicator light comes on m Remove the water container and fill it up to the S mark with fresh tap water approx 25 C to 35 C Add a Miele descaling tablet see Optional accessories to the water container m Replace the water container The 2 indicator light goes out After about 10 minutes the time it takes for the tablet to dissolve the descaling process begins Water is pumped into the steam generator at various times during the descaling process and is drained away again into the residual water container The indicator lights will alert you if you need to empty the residual water container or fill the water container The Bl and amp indicator lights now come on m Remove the water contain
5. and disconnected from the electricity supply Wait until the ironing table has cooled down m Undo the fastening of the ironing table cover at the tapered end of the ironing table m Remove the cover in the direction of the tower The felt underlayer remains on the ironing table m Wash and dry the cover in accordance with the instructions on the care label m Put the cover back on from the tower end first and draw it down towards the tapered end m Pull the cover taut using the cord and ensure that it is secure m Close the fastening of the cover and push it into the space at the tip of the ironing table The appliance is ready for use again Replacing the ironing table cover Do not use the appliance if the ironing table cover is damaged N Do not operate the appliance without an ironing table cover The ironing table cover must be replaced with an original Miele replacement N When changing the ironing table cover always ensure the appliance is switched off and disconnected from the electricity supply Wait until the ironing table has cooled down m Undo the fastening of the ironing table cover at the tapered end of the ironing table m Remove the cover in the direction of the tower The felt underlayer remains on the ironing table m Put the new cover on from the tower end first and draw it down towards the tapered end m Pull the cover taut using the cord and ensure that it is secure m
6. children P Children 14 years and older may only use the appliance if they have been shown how to use it in a safe way and understand the hazards involved P Children under 14 years of age must be kept away from the appliance unless they are constantly supervised P The appliance is not a toy To prevent the risk of injury do not allow children to play with it or use the controls Please supervise children whilst you are using the appliance P Danger of suffocation Packaging e g polystyrene and plastic wrappings must be kept out of the reach of babies and young children Dispose of or recycle all packaging safely as soon as possible Technical safety P Before setting up the appliance check it for any externally visible damage Do not use a damaged appliance It could be dangerous P Before connecting the appliance make sure that the connection data on the data plate voltage and frequency match the mains electricity supply If in any doubt consult a qualified electrician P Always remove and unwind the mains connection cable completely from the lower storage compartment P If the connection cable is damaged it must be replaced with a special cable of the same type available from Miele For safety reasons this must only be fitted by Miele Service or a Miele approved service technician Warning and Safety instructions P Do not use the appliance if the ironing table cover is damaged A damaged ironi
7. ensure that it functions correctly The appliance has an auto matic descaling function to assist you Frequency and requirement for descaling is dependent upon the water hardness level set Descaling is required more frequently with hard water than with soft water Only use the Miele descaling tablets supplied with the appliance They were specially developed for the Miele Fashion Master to optimise the descaling process Other descaling agents could damage the appliance You will need one descaling tablet for each descaling process Additional descaling tablets are available from Miele or online see Optional accessories The ironer or steamer must not be connected during descaling The appliance can be left unattended during descaling providing the iron or steamer is not connected Descale advanced warning When there are approx 2 operating hours remaining before the next descaling the S indicator light begins to flash red The light will flash more rapidly as the time counts down until it stays on permanently Cleaning and care Descaling can be started at any time whilst the red S indicator light is flashing by pressing the 8 button If the S indicator light is permanently on the remaining operating hours have expired You can still finish your ironing however the appliance must carry out descaling next time it is switched on before any more ironing is done m Disconnect the steam hose of t
8. m Once the iron has cooled down on the resting surface stow the iron and the steam hose holder in the upper storage compartment m Stow the steamer for B 1847 in the lower storage compartment Do not stow the iron or steamer if they are still connected Empty the water container if the system is not going to be used for a long period m The Fashion Master can now be put away Do not store the appliance in a room where there is a risk of frost occurring Frozen water can cause damage to the water container steam generator and steam hose Cleaning and care Cleaning the casing Disconnect the appliance from the electricity supply before any cleaning and maintenance work on the casing Do not use any abrasive cleaning agents Depending on the level of soiling the casing can be wiped with a wet or dry E cloth see Optional accessories Automatic rinse The automatic rinse function clears the steam generator of mineral deposits from the evaporated water After a water throughput of approx 3 litres the water from the steam generator is drained off into the residual water container when the Fashion Master is next switched on The rinsing process lasts a couple of minutes During the rinsing process the indicator light on the iron does not light up and the iron does not heat up when the steam ironing system has been switched on m If the 4 indicator light comes on fill the water contain
9. so called energy saving devices These reduce the energy supply to the appliance which could then become too warm If mains connection cable may only be replaced by an original Miele spare part WARNING THIS APPLIANCE MUST BE EARTHED 61 Technical data Dimensions when dismantled H x W x D Dimensions when assembled H x W x D Weight Voltage Connected load Fuse rating Steam pressure Steam output Capacity of water container Electrical connection cable length Steam hose length Ironing table height Ironing table length Ironing table width Product safety standard Test certificates awarded 62 1281 x 471 x 382mm 963 x 1460 x 471mm 29 kg for B 1312 and B 1826 30 kg for B 1847 See data plate See data plate gt 10A 3 5 bar for B 1312 4 0 bar for B 1826 and B 1847 100 g min 11 255 2 50m 1 80m 830 1020 mm 1200 mm 400 mm according to EN 60335 1 EN 60335 2 3 EN 60335 2 85 See data plate 63 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info 9 miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 1300 464 353 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Trading Ltd 1 3 Floor No 82 Shi Men Yi Road Jing an District 2000
10. the Fashion Master 2 222 cn seen 48 E El th mierofibre claihl 44 4404 rare 48 Problem solving guide 0 0 cee 49 Problem solving QUIde e eedem e em ae ae 49 After sales service loli lil es 60 cUm pe 60 Electrical connection liiis ii eei 61 Technical data iilii eil iles 62 Guide to the appliance Ironing table 2 Iron with steam hose 3 Steam hose holder Handle 8 Water container Tower Residual water container Upper storage compartment for the iron and the steam hose holder 8 X frame for the ironing table Iron resting surface Mains connection cable 62 Lower storage compartment for the mains connection cable steamer non stick sole plate and holder for the mains connection cable 43 Rollers Release mechanism Those features marked depend on model and may vary or not be available on your model Guide to the appliance Handle with rotary dial for adjustment and folding the appliance up 2 ron resting surface 8 Steam connection 4 Sockets for the steam hose holder 8 Control panel Steam hose holder Iron with steam hose 8 On Off button CD with indicator light S Steam ready amp 5 indicator light amp 9 Water container empty s indicator light Steam generator too hot x indicator light 2 Empty residual water container amp J indicator light 4 Descale S indicator light Descal
11. the steam button 25 on the iron drops of water or white deposits escape from the steam jets The temperature selected on the iron is too low Set the temperature to at least see Selecting the temperature for ironing The appliance is not ready to steam and the iron has not yet reached the selected temperature Wait for the indicator light to signal that the steam is ready and the selected iron temperature has been reached see Selecting the temperature for ironing Condensation has formed in the steam hose due to a pause in ironing To avoid wet spots on your laundry do not direct the first burst of steam after a pause onto the garment The 2 indicator light flashes once and the indicator light is also lit up The appliance was switched off during the descaling process or there was a power cut After power has been restored and the appliance switched on wait amoment The appliance will resume the descaling process from the point at which the power failed or the process was interrupted The 2 indicator light flashes twice and the L indicator light is also lit up The descaling process was not carried out properly Switch the appliance off and then back on again If the indicator light continues to flash call Miele Service The amp indicator light flashes three times and the L indicator light is also lit up There is a fault with th
12. the tower The programming procedure can be cancelled at any time by pressing the On Off button D The procedure can then be re started from the beginning again Programme the water hardness as follows m f the appliance is on switch it off using the D button m Press and hold the 8 button and at the same time switch the appliance on using the D button Hold in the button until the S indicator lights up yellow If this does not happen start the procedure again from the beginning The 4 indicator light flashes rapidly 10 times at intervals and the S indicator light flashes slowly on and off factory default The water hardness set is shown by the flash frequency of the s indicator light see table for water hardness 22 m Briefly press the 8 button to select the number of flashes which equates to your water hardness level Each press of the button moves you up a level When the highest water hardness value is reached the setting starts from the beginning again Please set the correct water hardness level as otherwise this invalidates the guarantee Example Water hardness 4 0 mmol l 22 dH The ll indicator light will flash rapidly 10 times at intervals factory default setting Press the 8 button 6 times The J indicator light flashes rapidly 6 times m Switch the appliance off with the D button Checking the programmed water hardness level m f th
13. 40 Shanghai PRC Tel 86 21 6157 3500 Fax 86 21 6157 3511 E mail mieleshanghai cn miele com Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola ew Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercareQmiele in nternet www miele in Manufacturer Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Germany Ireland Miele Ireland Ltd 2024 Bianconi Avenue Citywest Business Campus Dublin 24 Tel 01 461 07 10 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 nternet www miele co nz Singapore Miele Southeast Asia iele Pte Ltd 163 Penang Road 04 02 03 Winsland House Il Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg Internet www miele sg South Africa iele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 011 875 9000 Fax 011 875 9035 E mail info miele co za Internet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road
14. Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 1412 ce M Nr 09 370 090 00
15. Close the fastening of the cover and push it into the space at the tip of the ironing table The appliance is ready for use again 43 Cleaning and care Cleaning the sole plate of the iron N Caution Danger of burning The sole plate of the iron remains hot for some time after ironing Allow it to cool down before starting to clean it m Switch the appliance off and disconnect it from the electricity supply before cleaning the iron sole plate Depending on the level of soiling the sole plate can be wiped with a wet or dry E cloth see Optional accessories To avoid damaging the shiny surface of the sole plate do not use abrasive cleaning agents e g powder cleaners and cream cleaners chrome polish hard abrasive brushes or sponges e g pot scourers or sponges which have been previously used with abrasive cleaning agents sharp or pointed objects 44 Cleaning and care Cleaning the water filter The water filter prevents foreign objects in the water from getting into the appliance and causing damage If the water filter is dirty or blocked it can be cleaned A dirty water filter can cause more frequent pumping noises from the water feed pump m Switch the appliance off and disconnect it from the electricity supply before cleaning the water filter m Undo the screw on the water filter cover and lift the cover upwards and off In the cover there are to
16. Miele CareCollection has products which have been specially developed to clean your appliance gently and thoroughly Descaling tablets for the Fashion Master Miele descaling tablets guarantee an optimum result when descaling your Miele Fashion Master One tablet is required for each descaling process E cloth microfibre cloth Removes fingerprints and light soiling without damaging the surface 48 Problem solving guide With the help of the following notes minor faults in the performance of the appliance some of which may result from incorrect operation can be put right without contacting the Service Department NRepair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Problem solving guide Problem Possible cause Remedy The appliance will not operate There is no power to the appliance Check whether the mains plug is plugged in and switched on the fuse or circuit breaker has tripped The appliance will not operate following a power cut The appliance is switched off Switch the appliance on with the On Off button CD If the power cut occurred during an automatic rinse the process will be repeated when t
17. again and resumes the process which was started before the fault Switch the appliance off and then back on again There is a fault with the appliance If the indicator light continues to flash call Miele Service The appliance keeps switching off or the indicator light flashes nine times and the lt indicator light is also lit up The descaling process was interrupted by the appliance switching off The iron or steamer is connected when the appliance is switched on again Switch the appliance off and disconnect the iron or steamer from the steam connection Switch the appliance back on again The descaling process will resume 59 After sales service In the event of a fault that you cannot easily remedy please contact your Miele Dealer Of Miele see back cover for contact details Please note that telephone calls may be monitored and recorded for training purposes UK only When contacting Miele please quote the Model and Serial number of your appliance both of which are given on the data plate which is located in the tower behind the water container 60 Guarantee For information on the appliance guarantee specific to your country please contact Miele See back cover for contact details In the UK your appliance is guaranteed for 2 years from the date of purchase However you must activate your cover by calling 0845 365 6640
18. ample Tap water with 10 8 mmol l 60 dH in a 1 1 mixture with distilled water results in water hardness of 5 4 mmol l 30 dH The corresponding flash frequency of the L indicator light is 7 times according to the table see Setting the water hardness level Do not use demineralised water e g distilled on its own to fill the water container This can cause the appliance to malfunction Do not use condensate e g from other appliances such as air conditioning units tumble dryers etc or rain water Do not use any additives e g perfumes ironing water starch carbonated water etc CoolDown function If the iron is not moved for more than 3 minutes the heating switches off After some time steam is no longer available and the 45 indicator light goes out The iron will automatically start heating up again as soon as the iron is moved The time taken for steam to be available again depends on the length of time the heating was switched off The amp indicator light comes on when the appliance is ready to show that steam is available Do not leave the system unattended with the iron or steamer connected Always switch the appliance off and disconnect it from the electricity supply before leaving it Auto Off function If the iron or steamer is not used for a total of more than 14 minutes the whole appliance switches off automatically The system is switched back on again by pressing the D button
19. an be held directly on the textile with the brush attached Always try it out on an unobtrusive part of the fabric first The brush attachment helps to raise and straighten the fibres m Guide the brush attachment into the notches on the opposite side and click these into place m Hold the brush attachment in front of the steamer so that the lugs on one side fit into the notches on the steamer and click them into place m To remove the brush attachment pull it by the raised section off the steamer 34 Switching off Switch off the appliance m Press the On Off button D The yellow ring around the D button goes out The last fan settings selected are saved for the next time you switch on If you are putting the appliance away m Disconnect the appliance from the mains electricity supply m m Stow the electrical connection cable inthe lower compartment or hang it up on the cable clip The cable clip is in the lower compartment and can be pushed into one of the sockets for the steam hose holder 35 Storage m Place the iron on the resting surface to cool down Once the iron has cooled down you can fold the Fashion Master away The ironing table must be put back in the lowest working position in order to fold the appliance away Ensure that the residual water container is correctly inserted and clicked into place and take care not to trap the electrical connection cable in
20. can either be folded away or brought into the working position If the ironing table still will not click into place contact Miele 50 Problem solving guide Problem Possible cause Remedy Water is leaking from the steam ironing system at the height of the water container when it is being transported Water droplets can collect in the area under the water container as a result of frequent removal and replacement of the water container Dry the area underneath the water container in the tower with a cloth The iron or steamer does not heat up The appliance is switched off Switch the appliance on with the On Off button CD The steam hose is not plugged in properly Remove the steam hose and plug it into the steam connection again see Connection The iron has not been used for some time Move the iron or operate the steam button The temperature set on the temperature selector has been reached Wait a while until the iron heats up again Or if possible select a higher temperature The appliance is rinsing Wait until the rinsing process has been completed see Automatic rinse The indicator lights are showing that there is a fault Remedy the fault as explained on the following pages The appliance is damaged Call Miele Service 51 Problem solving guide Problem Possible cause
21. change between the iron and the steamer at any time during ironing without switching off the system After switching between the iron and steamer there is a pause before the steam is ready to ensure that the iron or steamer is sufficiently heated up The steamer is ready for use when the 5 indicator light on the tower control panel lights up and signals that the steam is ready Steamer The distance between the steamer and the textile is dependent on the sensitivity of the fabric and can vary between textiles Always test this first on an unobtrusive part of the fabric Condensate can form in the steam hose during pauses in ironing This is expelled by operating the steam button To avoid wet spots on your laundry do not direct the first burst of steam after a pause onto the garment N Danger of burning Do not direct the steam or the steam jets at people animals or electrical appliances of any kind Danger of burning Do not use the steamer on clothing while it is being worn as the clothing will intensify burning of skin The burst of steam is controlled by button D on the steamer For short bursts of steam m Press the button briefly and release it again For constant steam m Press and hold the button Always steam the textile in the direction of the fibres 33 Steamer Brush attachment The steamer comes with a brush attachment which can be clipped onto the head The steamer c
22. e and cause injury or damage if the table unfolded Assembling m Take the Fashion Master to the place where it is to be set up m Pull upwards on the release mechanism with one hand Hold the tower tightly by the handle with the other hand The locking mechanism on the tower will be released and the X frame will fold down at the same time m Hold onto the release mechanism and guide the ironing table into a position of approx 45 14 The ironing table is held independently in this position m Pull the ironing table upwards with both hands into a horizontal position until you hear a click a s N N a EE ggg py m Ensure that the ironing table has clicked into place on both sides of the tower otherwise you will not be able to adjust the height Assembling The Fashion Master is now assembled in its lowest working position a height of approx 83 cm A ssembling Adjusting the height You can adjust the Fashion Master to Su it your working height Take care not to trap the electrical connection cable in the mechanism Ensure that the ironing table has clicked into place on both sides of the tower otherwise you will not be able to adjust the height 16 Use one of the rotary dials on the side of the tower handle Turn the dial as far as it will go in the S direction and hold it there m At the same time pull the handle on the tower upwards wi
23. e and take the iron Out N The non stick sole plate remains very hot after use Avoid direct contact Hold it by the tab Do not store the non stick sole plate in its storage compartment until it has cooled down Ironing Fan The fan on the ironing table is controlled with the t amp X or x AS buttons B 1312 only The blow function is activated by the t amp button The suction function is activated by the R button B1826 and B 1847 only You can switch between the blow and suction functions with a single press on the R button You can switch between the two power output levels with a single press on the AS button Power setting 1 2 1 fan active Power setting 2 2 fans active The fan s are located on the underside of the ironing table Suction function The suction function assists steam permeation of textiles avoids the formation of condensation on the ironing table and holds the item so that it does not slip off the ironing table Blow function The blow function creates a cushion of air between the textile and the ironing table and helps prevent seams being pressed into the garment It also assists with ironing frills sequins etc and allows you to iron without flattening the fabric Automatic switch on off Automatic switch on off ensures that the fan starts at exactly the right time when using steam After a short running on time the fan stops automatically because the fan i
24. e appliance Call Miele Service 56 Problem solving guide Problem Possible cause Remedy The 2 indicator light flashes four times and the 2 indicator light is also lit up The empty or missing water container is not recognised by the appliance The water container is not inserted properly causing air to be sucked in The water feed pump is being activated but is not running Switch off the appliance Fill the water container with fresh tap water and replace it Do not use distilled water Switch the appliance back on again The x indicator light is lit up When the steam generator cools down it empties automatically The steam generator is then automatically refilled so it is ready to steam again The water filter is blocked or missing Clean and replace the water filter see Cleaning the water filter If the indicator light continues to flash call Miele Service The 2 indicator light flashes five times and the 2 indicator light is also lit up There is a fault with the appliance Switch the appliance off and then back on again If the indicator light continues to flash call Miele Service 57 Problem solving guide Problem Possible cause Remedy The amp indicator light flashes six times and the L indicator light is also lit up The steam generator is contaminated with water whic
25. e appliance is on switch it off using the D button m Press and hold the 8 button and at the same time switch the appliance on using the D button Hold in the button until the S indicator lights up yellow The el indicator light will flash the number of times which corresponds to the water hardness level which has been set see table m Switch the appliance off with the D button Switching on Switching on the Fashion Master m Press the On Off button D The ring around the CD button lights up yellow The Fashion Master starts heating up Steam can escape from the iron during the heating up phase During operation pumping boiling and knocking noises may be heard These are normal noises which occur during operation When the appliance is ready and steam is available the 45 indicator light comes on Filling the water container If the water container is empty or not inserted into the system the L indicator light comes on m Remove the water container Hold the container by the integral handle then pull it out and upwards to remove it The water container can drip a little when it is being removed until the container valve closes Removing the water container slowly can prevent it from dripping 23 Switching on m Turm the screw cap on the back of the water container anti clockwise and lift it off m Tilt the water container into a
26. e button 8 Warning and Safety instructions This appliance complies with all relevant safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information about its safety use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Correct application P This appliance is not designed for commercial use It is intended for use in domestic households and similar working and residential environments P The appliance must be used only for ironing textiles which are suitable for ironing according to the care label P The appliance is intended for domestic use only as described in these operating instructions Any other usage is not supported by the manufacturer and could be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation P The appliance can only be used by people with reduced physical sensory or mental capabilities or lack of experience and knowledge if they are supervised whilst using it or have been shown how to use it in a safe way and understand the hazards involved P The appliance is not intended for outdoor use Warning and Safety instructions Safety with
27. ect the iron or the steamer from the steam connection The button was not pressed for long enough Press the 8 button for longer There is a fault with the appliance Call Miele Service 53 Problem solving guide Problem Possible cause Remedy The appliance switches off during the descaling process The iron or the Steamer was connected during the descaling process Disconnect the iron or the steamer from the steam connection Switch the appliance on again The indicator light is on The water container or contents have not been recognised Remove the water container fill and replace it Rinsing or descaling could still be taking place Wait until the process has finished Programming of the water hardness level has not yet been completed Complete this process If the indicator light is still on call Miele Service The indicator light is on during the descaling process The water container or contents have not been recognised Insert the water container again Fill the water container with a little more water and replace it If the indicator light is still on call Miele Service The s indicator light is constantly lit up The steam generator has overheated Allow the steam ironing system to cool down The steam ironing System is ready to use again when the x indicator light has gone ou
28. er m If the amp indicator light comes on empty and replace the residual water container The contents of the steam generator will drain off into the residual water container Some steam will escape during this process The amp indicator light comes on Emptying the residual water container The residual water container may be hot after rinsing m Set the appliance to its highest working position see Adjusting the height to allow access for removing the residual water container Only remove the residual water container when prompted by the amp indicator light m Remove empty clean and dry the residual water container The residual water container can be cleaned in the dishwasher or by hand using hot water with a little washing up liquid 39 Cleaning and care Make sure that the metal contact discs at the top of the residual water container are cleaned and dried properly These metal discs send a signal to the appliance when the residual water container is full or if it is not in the appliance The discs will not convey these signals if they are dirty or damp m Insert the residual water container after a short interval approx 15 seconds so that it clicks into place The amp indicator light goes out The Fashion Master is now ready to use again When the amp 5 light comes on you can use steam again 40 Automatic descaling The appliance should be descaled regularly to
29. er and rinse it thoroughly making sure there are no limescale deposits left in it m Fill the water container up to the S mark with fresh tap water and replace it in the appliance m Remove and empty the residual water container m Replace the residual water container 42 The L and amp indicator lights go out After an activation period of about an hour all the water from the steam generator is drained away into the residual water container Water is now pumped into the steam generator to rinse it out The water is then drained away completely into the residual water container The amp J indicator light comes on again The residual water container may be hot after rinsing m Remove and empty the residual water container m Rinse out and dry the residual water container thoroughly The residual water container can be cleaned in the dishwasher or by hand using hot water with a little washing up liquid m Replace the residual water container The amp indicator light will go out now The S indicator light goes out as well and the appliance switches off Switch on using the D button The appliance is now ready to use again Cleaning and care Cleaning the ironing table cover If the ironing table cover is soiled it can be removed for washing Do not operate the appliance without an ironing table cover N When removing the ironing table cover always ensure the appliance is switched off
30. h is too hard or too salty Start the descaling process by pressing the button In this case the descaling requirement is not indicated by the S light see Cleaning and care To avoid this problem in the future set the water hardness level at least a stage higher for example if it is set to 4 increase it to 5 or more see Setting the water hardness level There is a fault with the appliance Switch the appliance off and then back on again If the indicator light continues to flash call Miele Service The 2 indicator light flashes seven times and the L indicator light is also lit up There is a fault with the appliance Switch the appliance off and then back on again If the indicator light continues to flash call Miele Service 58 Problem solving guide Problem Possible cause Remedy The amp indicator light flashes eight times and the indicator light is also lit up The residual water container has not been recognised Switch off the appliance Wash and dry the metal contacts on the residual water container Switch the appliance on again and reset it as follows Insert the residual water container filled with water for atleast 15 seconds Remove the residual water container again and empty it Replace the empty residual water container after at least 15 seconds The appliance is ready to use
31. he appliance is switched on again If the power cut occurred during automatic descaling the process will be resumed from the stage in which it was interrupted when the appliance is switched on again The height adjustment mechanism on the ironing table is not functioning The ironing table is not clicked into place on both sides of the tower Click the ironing table into place on both sides of the tower see Assembling 49 Problem solving guide Problem Possible cause Remedy The appliance will not fold away The ironing table is not in its lowest working position Adjust the ironing table to its lowest working position see Storage The residual water container is not correctly inserted and clicked into place Insert the residual water container fully into the tower until it clicks into place Then adjust the ironing table to its lowest working position see Storage The ironing table will not click into place during assembly or dismantling for storage The ironing table is displaced because the tower was not in the lowest position TT LL ll Press and hold the release button on the tower and at the same time turn the rotary height adjustment dial as far as it will go towards S and hold it steady Push the tower into its lowest working position and then let go of the rotary dial and then the release button Now the ironing table
32. he iron or the steamer from the steam connection m Set the appliance to the highest working position to allow access for removing the residual water container during the descaling process Do not connect the iron or the steamer during descaling This would interrupt the descaling process by switching off the appliance If it is switched on again without the iron or steamer attached the descaling process is continued The residual water container can become hot during the descaling process Only remove and empty the residual water container when prompted to do so by the by indicator light Otherwise hot water could spill out and cause injuries and or damage to the appliance To prevent unwanted removal of the container set the appliance to its lowest working position The appliance must be put back into its highest working position to remove the residual water container The descaling process can be interrupted by switching the appliance off with the D button When it is switched back on the descaling process will resume from the stage at which it was interrupted Starting the descaling process m Press the On Off button D to switch on the appliance The ring around the D button lights up yellow m Press the 8 button for a few seconds to start the descaling process The S indicator now lights up yellow If the residual water container is not inserted or is full the amp indicator light comes on m
33. horizontal position and fill it with fresh tap water approx 25 C to 35 C In this position even very low taps can be used to fill the water container It is not possible to overfill the water container The water container can be removed and refilled at any time during the ironing process The amount of water required will depend on how much laundry is being ironed m Replace the screw cap and turn clockwise as far as it will go it m Replace the water container The el indicator light will go out after a short time The steam will be ready for use again more rapidly if the water container is refilled promptly 24 If you refill and replace the water container as soon as the indicator light d lights up there is no delay The amp indicator light indicates readiness im mediately While the el indicator light is on the steam system is not active The iron remains functional Energy saving tip You can save energy by ironing without steam by removing the water container so that the steam generator is not heated Empty the water container if the system is not going to be used for a long period Switching on Water quality Use only fresh tap water Filtered tap water may also be used For water hardness of more than 2 5 mmol l 14 dH you can use tap water mixed in 1 1 ratio with distilled water This halves the water hardness Set the halved water hardness to the corresponding flash frequency Ex
34. ilm from the tower etc When using for the first time you might notice a slight odour during the heating up phase This will dissipate with further use During operation pumping boiling and knocking noises may be heard These are normal noises which occur during operation 20 Water hardness To ensure problem free functioning and so that the descaling reminder appears at the right time it is important to adjust the appliance to the local water hardness level The water hardness level indicates how much calcium is dissolved in the water The higher the calcium content the harder the water and the harder the water the more often the appliance will need to be descaled Your local water board will be able to tell you the hardness level of your water This information can often be found on the internet on the home page of the relevant water board Set the water hardness according to the table The water hardness set is shown by the flash frequency of the s indicator light dH mmol l f Flash German frequency scale 1 4 0 2 0 7 2 7 Once 5 7 0 9 1 3 9 13 Twice 8 11 1 4 2 0 14 20 3 times 12 15 22 27 22 27 4 times 16 20 2 9 3 6 29 36 5 times 21 25 3 8 4 5 38 45 6 times 26 30 47 54 47 54 7 times 31 36 56 65 56 65 8 times 37 45 6 7 8 1 67 81 9 times 46 70 8 3 12 6 83 126 10 times Before using for the first time If you cann
35. lop Condensate can form in the steam hose during pauses in ironing This is expelled by operating the steam button To avoid wet spots on your laundry do not direct the first burst of steam after a pause onto the garment Ironing without steam If you want to iron dry you can save energy by removing the water container so that the steam generator is not heated 29 Ironing Ironing with the non stick sole plate In the lower compartment there is a non stick sole plate which simply clips onto the iron Danger of burning The sole plate becomes very hot when in use Avoid direct contact with it m Place the iron tip first in the non stick sole plate m Pull back the tab on the bottom of the non stick sole plate hold onto it and push the iron onto the non stick sole plate m Then release the tab This will clip onto the iron m Wait for about 1 minute until the non stick sole plate has heated up before starting to iron With the non stick sole plate you can generally iron appliqu s printed or flocked textiles etc without turning the garment inside out 30 It also reduces or eliminates the formation of shiny patches on dark textiles Always try it out on an unobtrusive part of the fabric first Removing the non stick sole plate Danger of burning The sole plate becomes very hot when in use Avoid direct contact with it m Pull back the tab on the bottom of the non stick sole plat
36. ng table cover could be dangerous Do not use the appliance without an ironing table cover The ironing table cover must be replaced with an original Miele cover gt The electrical safety of this appliance can only be guaranteed when correctly earthed It is most important that this basic safety requirement is observed and regularly tested and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for damage or injury caused by an inadequate earthing system e g electric shock P Do not connect the appliance to the mains electricity supply by a multi socket adapter or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating P This appliance complies with all relevant safety requirements Unauthorised repairs could result in unforeseen dangers for the user for which Miele cannot accept liability Repairs should only be undertaken by a Miele approved service technician otherwise any subsequent damage will not be covered by the guarantee P Faulty components must only be replaced by genuine Miele original parts Only when these parts are fitted can the safety standards of the appliance be guaranteed P During installation maintenance and repair work the appliance must be disconnected from the mains electricity supply P Do not damage remove or bypass the safety features fixtures and co
37. ning without steam i i e 29 ironing with the non stick sole plate iilis 30 Removing the non stick sole plate iles 30 Fe a ee ee ee 31 SUCTION TUNCUON ato cot ae ee ee Aa en Am en Babes ates 31 BIOWMUNCHON a a ea een ie ne 31 Automatic Switehr on off s 222 de Eder reet nude 31 Memory TUI COLS re a ES Pied tube 44 31 Heated ironing surface iiis 31 Steamer uos A a EREN Sd in eR Odea PARE EOP es E quee RE 32 Steamer B 1847 only asus pex a egetras ax abes Fed Be dead vu 32 Br snmn attachtmert ence eee sca FOR edet ann 34 Contents Switching oft 35 Storage eee ee edu bete uti is be Pet b MEE 36 Cleaning and care 39 Cleaning tlie Casing ss sss rettete Birne 39 Automate Insee aac vdd dep X dace euer tun Pot eae s AR dca ed 39 Emptying the residual water container lile 39 Automatie desealng xu Les a tere urat t ere OR ei a e 40 Descale advanced warning iiie 40 Starting the descaling process liie 41 Cleaning the ironing table cover see 43 Replacing the ironing table cover iiie 43 Cleaning the sole plate fiheiron 0 0000 eee 44 Cleaning the water filter 2i 45 Optional accessories 47 GGESSOFIESH io ba ar Barren bo a abe 47 Non stiek SOlGeJlate a wie dda a ae a aan 47 koning table CoVer aa war OR cde en ai ag ea ees 47 LOGIN Clic ee ee ee ee ae one een een 47 Cleaning PIOGUCIS 32a eR ale een ed 48 Descaling tablets for
38. ntrol elements of this appliance P Any removable outer panels must be fitted in place and all moving or electrical parts shielded before it is switched on Warning and Safety instructions P The appliance must not be used in a non stationary location e g on a ship P In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Correct use Caution Danger of burning The steam emitted the iron sole plate and the steamer jets are very hot P This appliance is intended for domestic use only and is not to be used for commercial purposes P Do not use a pressure washer or hose to clean the appliance P Only clean the appliance when it has cooled down P Danger of squashing and trapping your fingers Do not place your fingers between moving parts when assembling dismantling or adjusting the height of the appliance P The appliance must be set up on an even surface and may only be used in a horizontal position gt The steam ironing system must be assembled when ironing however the steamer can be used when the system is dismantled P Ensure that the electrical connection cable does not present a trip hazard when unwound P When the appliance is heated up there is an acute danger
39. of burning from contact with the sole plate of the iron or the steamer jets Warning and Safety instructions P Do not use demineralised water e g distilled on its own to fill the water container as this could cause the appliance to malfunction P Always place the iron with the steam function switched off on the iron resting surface so that the sole plate does not protrude over the edges Placing it otherwise could be a fire hazard P Take care not to burn yourself If the iron remains on the resting surface for any length of time the surface will become hot Avoid direct contact with it Only touch the handle P Danger of burning Do not direct the steam or the steam jets at people animals or electrical appliances of any kind P Danger of burning Do not use the steamer on clothing while it is being worn as the clothing will intensify burning of skin P Switch the appliance off before disconnecting it from the mains electricity supply P Do not leave the appliance unattended when it is ready for use Switch it off and then disconnect it from the mains electricity supply P Do not pull on the cable to remove the plug Pull on the plug P Do not touch the electrical connection cable or the steam hose with the sole plate of the heated iron This could result in damage P The iron and the steamer must not be connected to the appliance during the descaling process The appliance can be left unattended du
40. ols for removing both the seal and the water filter m Remove the water container Hold the container by the integral handle then pull it out and upwards to remove it m Remove the seal on the right hand socket with the appropriate tool 45 Cleaning and care m Attach the appropriate tool in the cover onto the water filter in the right hand socket and remove it m Remove the water filter from the tool m Clean the water filter thoroughly under running water 46 m Replace the water filter ensuring that the filter seal is underneath m Replace the seal in the right hand socket m Replace the cover and tighten the screw m Replace the water container The appliance is ready for use again Do not use the appliance if the water filter is not in place as this will cause a fault to be indicated See Problem solving guide The water filter must be replaced if it is worn or damaged Only use genuine original Miele replacement parts These are available from Miele see back cover for contact details or from your Miele dealer Optional accessories Miele appliances are built to the highest standards to achieve the best possible results for as long as possible To help you get the most out of your appliance Miele also offers a comprehensive range of accessories and care products The following products are just a few examples from our full range which is available to
41. or registering online at www miele co uk Electrical connection NA electrical work must be carried out by a suitably qualified and competent person in accordance with current local and national safety regulations BS 7671 inthe UK This appliance is supplied with a connection cable and moulded plug BS 1363 for connection to a 230 V mains supply The appliance must only be operated with the voltage frequency and fuse rating shown on the data plate located in the tower behind the water container Please ensure these match the household mains supply We recommend connecting the appliance to the power supply via a suitable plug and socket which must be easily accessible for servicing and maintenance work Do not connect the appliance to the mains electricity supply by a multi socket adapter or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating For extra safety and protection we recommend connecting the appliance by a 30 mA residual current device RCD If the electrical connection cable is faulty this must only be replaced by a suitably qualified and competent person The appliance must not be connected to the inverter of an autonomous power supply e g a solar power system When switching the appliance on a surge in the power could trigger the safety cut out mechanism This could damage the electronic unit The appliance must not be used with
42. order online at www miele shop com or from Miele see back cover for contact details or from your Miele dealer Accessories Non stick sole plate With the non stick sole plate you can generally iron appliqu s printed or flocked textiles etc without turning the garment inside out It also reduces or eliminates the formation of shiny patches on dark textiles The non stick sole plate can be used on the iron of any Miele Fashion Master regardless of model Ironing table cover Miele ironing table covers are hard wearing and highly absorbant The separate needle felt under layer is steam permeable and pleasantly cushioned Both can be used for any Miele Fashion Master regardless of model Basic ironing table cover Colour mottled grey The basic ironing table cover consists of 65 polyester and 35 cotton and can be washed as necessary at 40 C Aramid ironing table cover This ironing table cover has particularly good heat resistance and durability due to the aramid fibres Colour anthracite The aramid ironing table cover consists of 100 aramid and can be washed as necessary at 40 C Steamer The steamer facilitates the smoothing of hanging textiles e g dresses and jackets It comes with a brush attachment for raising and straightening the fibres The steamer can be used with any Miele Fashion Master regardless of model 47 Optional accessories Cleaning products The
43. ot find out the water hardness level you can use the test strip provided m Dip the strip in your drinking water for approximately a second then shake off any excess water The result will be evident after about a minute Set the water hardness according to the table The water hardness set is shown by the flash frequency of the e indicator light If your water hardness is different from this you must adjust it to the corresponding value Where the water hardness fluctuates e g between 6 7 9 0 mmol l 37 50 dH always programme it to the higher value 9 0 mmol l 50 dH in this example In the event of a fault it will help the service technician if you know the hardness of your local water supply Enter the water hardness below mmol or dH Hardness range on the test Flash strip frequency 4 green squares 0 5 mmol Once or 3 dH 1 red square 0 7 mmol Twice or 4 dH 2 red squares gt 1 3 mmol l 3 times or 7 dH 3 red squares 2 5 mmol 5 times or 14 d 4 red squares 3 8 mmol 10 times or 21 d The FashionMaster is set to the highest level of water hardness 12 6 mmol l 70 dH as a factory default If your water hardness corresponds to this you do not need to do anything See Switching on 21 Before using for the first time Setting the water hardness level Water hardness is programmed using the control panel on
44. ring this process gt The iron must not be stowed in its storage compartment when it is connected as this could result in damage to the appliance P Do not use the residual water container to store accessories or other similar items It should be used only to collect residual water 10 Warning and Safety instructions P Do not plug any objects into any of the apertures on the steam ironing system If an aperture is blocked do not use the system P Do not hang items of laundry on the appliance when folded as this could cause it to tip over P Do not store the appliance near petrol benzine or other easily flammable substances Fire and explosion risk P Only use the appliance in buildings with an ambient temperature of between 10 C and 40 C Freezing temperatures excessive heat and humidity will affect the functionality of the system P Do not store the appliance in a room where there is a risk of frost occurring Frozen water can cause damage to the water container steam generator and steam hose Using accessories P Accessory parts may only be fitted when expressly approved by Miele If spare parts or accessories from other manufacturers are used this will invalidate the guarantee and Miele cannot accept liability Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Caring for our environment Disposal of the packing material The transpo
45. rt and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled Ensure that any plastic wrappings bags etc are kept out of the reach of babies and young children Danger of suffocation 12 Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal Moving the Fashion Master The appliance is fitted with two rollers so it can be pulled or pushed across an even surface when folded up m Hold on to it by the handle and tip it gently towards you until the wheels are free Obstacles such as carpet edges door sills or single steps can also be easily negotiated Two people are required to carry the Fashion Master up or downstairs It should always be carried with the ironing table underneath m Use the hand holds on the underside of the appliance N Do not lift and carry the Fashion Master by the ironing table The locking mechanism on the tower could releas
46. s not needed during pauses in ironing e g when the textiles are being folded Memory function The memory function saves the last used fan direction and power setting Heated ironing surface When the appliance is switched on the ironing surface will heat up automatically helping to reduce the formation of condensation on the ironing table 31 Steamer Steamer B 1847 only The B 1847 Fashion Master is equipped with a steamer in addition to the iron The steamer can also be used with models B 1312 and B 1826 optional accessory The steamer facilitates the ironing of hanging textiles e g dresses and jackets It is fitted with a removable brush attachment 2 for raising and straightening the fibres The steamer is lighter than the iron and also has no hot sole plate eliminating the risk of shiny patches due to unintentional contact with the textiles The steamer can also be used when the appliance is dismantled 32 The steamer can be plugged into the steam connection as an alternative to the iron m Remove the steamer from the lower compartment m Disconnect the iron from the steam connection in the tower Pull back the sliding mechanism on the steam hose plug and withdraw the plug Do not pull on the steam hose m Plug the steam hose of the steamer into the steam connection Pull back the sliding mechanism on the steam hose plug and release it when it is plugged in You can
47. sitive fabrics such as synthetics first Then iron silk wool cotton and linen at increasing temperatures Please also observe the advice and symbols on the care labels in your garments 27 Ironing Iron B 1826 and B 1847 Your Fashion Master has one of the following irons depending on model B 1312 2 Sliding switch for constant steam 3 Power output selection button AS Steam button Blow suction button t4 2 Sliding switch for constant steam Suction button Jt Blow button 4f 28 Ironing Ironing with steam The burst of steam is controlled by the 2 button The fan starts up when the amp button is pressed The fan will continue running for a short while after using steam For short bursts of steam m Press the button briefly and release it again For constant steam m Press the amp button and at the same time slide switch 2 backwards Now release the 23 button Steam will be continuously released m o stop using steam continuously unlock the amp button by pushing the 2 sliding switch forwards again Steam output will stop When putting the iron down on the iron resting surface the steam lt b button must be unlocked m f the el indicator light comes on fill the water container see Filling the water container When using the steam function for a long time make sure the room is sufficiently ventilated as high air humidity can deve
48. t If the indicator light is still on call Miele Service 54 Problem solving guide Problem Possible cause Remedy The lt indicator light is on constantly The empty residual water container has not been recognised Empty the residual water container completely and dry it out Insert the residual water container after a short interval approx 15 seconds so that it clicks into place Clean and dry the metal contacts on the residual water container and replace the container If the indicator light is still on call Miele Service The steam function on the iron or steamer does not work The appliance has not been switched On Connect the appliance to the mains electricity supply and switch it on with the On Off button D The iron or steamer are not connected Connect the steam hose to the steam connection on the tower The water container is empty or missing Fill the water container with fresh tap water replace it and wait for the indicator light to signal that steam is ready The steam is not ready Wait until the indicator light to signals that steam is ready The indicator lights are showing that there is a fault Remedy the fault as explained on the following pages If still no steam is produced call Miele Service 55 Problem solving guide Problem Possible cause Remedy When using
49. team hose plug and release it when it is plugged in m Plug the steam hose holder into one of the sockets provided Please note Use the socket on the side on which you are ironing m Guide the rubber ring on the steam hose into the steam hose holder as The appliance can be used by right or shown left handed people Operation is optimised for both sides p Ensure the steam hose fits securely and that it is not twisted m Open the lid of the steam connection by lifting it upwards 18 Connection m To avoid damaging or fading the ironing table cover always place the iron on the resting surface during pauses in ironing Condensation can form on the resting surface However this does not affect the functioning of the steam ironing System When putting the iron down on the iron resting surface the steam lt b button must be unlocked N The iron must not be placed upright on the resting surface as it could tip and fall Always place the iron down so that it is resting on the entire sole plate Danger of burning If the iron remains on the resting surface for any length of time the surface will become hot Avoid direct contact with it Only touch the handle Before using for the first time It is helpful to get to know the FashionMaster before using it for the first time so that you will be able to make use of all the functions m Remove the packaging e g the protective f
50. th the other hand Or m Press the handle on the tower down at the same time Do not push down on the ironing table when doing this m When you have reached your desired working height release the rotary dial and it will spring back into the middle position We recommend that you adjust the working position to approx hip height for optimum comfort The ironing table is held in the selected position For additional stability the ironing table clicks into place audibly under extra pressure doubly securing your selected working position The highest working position is approx 102 cm Connection The Fashion Master system is supplied for connection to a 230 volt 50 Hz mains electricity supply and is fitted with a moulded BS 1363 plug m Guide the electrical connection cable through the grove provided and close the lower storage compartment again Ensure that the cable does not become trapped between the lid and the casing or between the rollers and the tower m Open the lower storage compartment by opening the lid downwards m Remove the electrical connection m Open the upper storage cable completely from the compartment lid polpargnent m Take out the iron and the steam hose m Insert the plug in a wall socket holder Connection m Close the storage compartment lid m Connect the iron by plugging the again steam hose into the steam connection Pull back the sliding mechanism on the s
51. the mechanism m At the same time push the tower handle downwards to lower the ironing table into the lowest working position Do not push down on the ironing table m Release the rotary dial and it will spring back into the middle position m To prevent this use one of the rotary dials on the side of the tower handle Turn the dial as far as it will go in the S direction and hold it there 36 Storage Make sure that the ironing table is in its lowest working position when releasing it There must also be nothing on the ironing table m Turn one of the rotary dials as far as it will go towards Gf The ironing table is now released m Release the rotary dial and it will spring back into the middle position m Guide the ironing table downwards or allow it to slide down by itself The ironing table is held independently in this position m Push the ironing table upwards by the tapered end into an upright position until it clicks into position on the tower 37 Storage m Push the bottom of the X frame which is still protruding in until it clicks into position m Disconnect the iron or steamer from the steam connection in the tower Pull back the sliding mechanism on the steam hose plug and withdraw the plug Do not pull on the steam hose Caution the plug can still be warm immediately after use A small amount of water can escape from the steam hose 38
Download Pdf Manuals
Related Search