Bosch WAQ24461GB washing machine
Contents
1. L 1 Change the height by turning the appliance feet lighten the lock nut against the housing Intense noise formation vibrations and wandering may be the result of incorrect alignment Loosen the lock nut using a wrench by turning it in a clockwise direction Caution all four appliance feet must be firmly on the ground The washing machine must not wobble Check the alignment of the washing machine with a spirit level and adjust if necessary In doing so hold the foot tight and do not adjust its height Caution the lock nuts on all four appliance feet must be screwed tightly against the housing Electrical connection The washing machine must only be connected to an alternating current via a properly installed earthed socket The power supply and voltage indicated on the washing machine rating plate must be the same The connected load and fuse required are specified on the rating plate E _ 73 Make sure that the mains plug fits the socket the cable cross section is adequate the earthing system is properly installed a If this is necessary the mains cable may only be replaced by a qualified electrician Replacement mains cables are available from the after sales service a l i OD E Do not use multiple plugs couplings or extension cables Sa LO lf a residual current circuit breaker is used only use a type which displays this2. 1 2 bar 6 I min with 1 bar consumption parameters cannot be assure f the water pressure is higher than this a pressure reducing valve must be installed Connection to the tap Connection to the Aqua Stop Aqua Secure Standard machine no necessary with Aqua Stop fixed installation Aqua Stop Aqua Secure Aqua Secure Standard 1 Connect the water inlet hose hoses to the tap taps 3 4 valves Caution only tighten the screw connections by hand 2 Open the water tap taps carefully checking the leak tightness of the connection points Caution the screw connection is under mains water pressure Connection in case of hot water models COLD Cold water HOT Hot water max 60 C red If no hot water connection is present my connect the cold water inlet hose an cover the hot water connection on the appliance so that it is kept free of dirt 26 4 mm and to the solenoid Water outlet Caution do not bend or pull lengthways Height difference between the installation surface and the drain min 60 cm max 100 cm Outlet in a sink Caution secure the drain hose from slipping out Caution the plug must not block drainage from the sink During pumping check whether the water is draining away quickly enough The end of the drain hose must not be immersed in the water pumped out This risks water being sucked back into the washing machine Drainage into a siphon Caution
3. A Installation in a kitchenette underneath the worktop or fitted in a cabinet Recess width of 60 cm required Only install the washing machine underneath a continuous worktop that is securely connected to adjacent cabinets Installation underneath the worktop Risk of electric shock Instead of the appliance covering plate you must have a metal cover order no WMZ20331 WZ20331 Recess width of 60 cm required Moisture inside the drum is due to final testing Scope of delivery 021012101011010 mela 1110102 Aqua Stop Hot water Aqua Secure amp Standard Mains cable Water outlet Water inlet for fixing the drainage hose in place Adapter 1 2 3 4 depending on model Covers Also required depending on the connection 1 hose clamp 24 40 mm exclusive dealers to connect to a siphon page 4 water connection Useful tools Spirit level for installation Wrenches WAF 13 for loosening transport braces gt page 3 and WAF 17 for aligning appliance feet page 5 Hose and cable lengths 027012141011010 K0 1 1110102 i Available from specialist dealers the after sales service Extension for Aqua Stop or cold water inlet hose approx 2 50 m order no WMZ2380 WZ10130 CZ11350 Z7070X0 Longer inlet hose approx 2 20 m for standard model Removing the transport braces Before using the appliance for
4. been i UCOrtenitsS Page set up and connected correctly in accordance with our instructions this also includes a correctly fitted Aqua Stop extension original accessories E Safety instructions 2 ee eee eee 1 Our warranty goes not cover defective power cables or fittings between the Aqua Stop M Installation surface 6 6 e ee eee eee ee 1 connection and the tap E Installing the appliance yeh Pee a eee ee ee 1 4 Appliances with Aqua Stop do not need to be supervised during operation nor secured Senge puesta ihe eS eee afterwards by turning off the tap SUIE ia PE ast Fat Bs ee eae The tap only needs to be turned off if you are away from home for a long period e g for E Removing the transport braces 3 several weeks holiday M Water connection 0000 eee ees 3 4 E Alignment lt 4 24 taken dca atu Hos ne hee eS 5 M Electrical Connection aaau aaa 5 E Transportation e g when moving home 6 Technical specifications 000008 6 After sales Service aaau ca 7 Aqua Stop warranty 0 000000 cee eee eee T Read these instructions before switching on the washing machine Also observe the separate Instruction manual Keep all documents for use in the future or for the subsequent owner
5. the connection point must be secured with a hose clamp 24 40 mm exclusive dealers Alignment A Intense noise formation vibrations and wandering may be the result of incorrect Transportation e g when moving home After sales service Before transporting the washing machine f you cannot rectify the fault yourself Operating instructions What to do if page 11 please contact our after sales service We will always find a suitable solution and will avoid a C Washing machine visit from a service technician wherever possible alignment Turn off the tap 1S Aligning the washing machine with a spirit level a The contact details for all countries can be found in the enclosed after sales service directory 2 Drain residual water Operating instructions Maintenance drain pump 3 Release the water pressure in the inlet hose Operating instructions Maintenance filter 1 Loosen the lock nut using a wrench by turning it in a clockwise direction in water inlet _ Please give the after sales service the product number E Nr and the production number 4 Disconnect the washing machine from the power supply FD of the appliance 5 Dismantle the hoses You will find this information on the inside of the 2 Change the height by turning the appliance feet Caution all four appliance feet must be firmly on the ground The washing machine must not wobble Check the alignment of the wa
6. Installation surface Installing the appliance AN Safety instructions The washing machine is heavy take care when lifting Caution frozen hoses may rip burst Do not install the washing machine in areas exposed to frost or outdoors The washing machine could be damaged Do not lift the appliance by protruding components e g the washing machine door the cover the front panel or the outer door in case of deco models In addition to the instructions provided in this document special regulations from the relevant water and electric utility companies may apply Ifin doubt have a technician connect the appliance Lay hoses and cables in such a way that there is no risk of tripping The machine must be stable so that it does not move around The installation surface must be firm and level Soft floors floor coverings are not suitable Installation on a pedestal The feet of the washing machine must be secured with holding brackets order no WMZ2200 WX9756 CZ110600 Z7080X0 Installation on a wood joist floor If possible place the washing machine in a corner Screw a water resistant wooden board min 30 mm thick to the floor The feet of the washing machine must be secured with holding brackets order no see above Installation on a platform with drawer order no WMZ20490 WZ20490 A Install the appliance before connecting it to the power supply
7. Zi symbol Ax O 5E Only this symbol guarantees compliance with the currently applicable regulations 0 Do not plug in or unplug the mains plug with wet hands Pull the appliance plug out of the socket at the plug only not by the cable z Manufacturer gt Operating instructions Transportation e g when moving home Before transporting the washing machine Turn off the tap 2 Drain residual water Operating instructions Maintenance drain pump 3 Release the water pressure in the inlet hose Operating instructions Maintenance filter in water inlet 4 Disconnect the washing machine from the power supply 5 Dismantle the hoses Ca Preparing and installing transport braces 1 Remove all covers and store them 2 Affix all transport braces In doing so turn the bend on the hose holders inwards Clamp the mains cable in the holders Tighten the screws A N After transportation the transport braces must be removed page 3 2 litres of water into compartment IlI and start the Empty programme i prevent unused detergent from flowing straight into the drain during the next wash Pour Technical specifications Dimensions width x depth x height 60 x 55 x 85 cm Weight 66 73 kg depending on model Mains connection Nominal voltage 220 240 V 50 Hz Nominal current 10 A Nominal power 2 300 W Water pressure 200 1000 kPa 2 10 bar After sales service If you cann
8. ce for the first time make sure that you Water inlet completely remove transport braces and keep them for subsequent transportation Ifyou need to transport the appliance at a later date always re affix the transport braces to prevent damage to the machine page 6 Store the screw and sleeve together Caution do not bend squash modify or cut through otherwise its strength is no longer guaranteed Optimum water pressure in the supply network 200 1 000 kPa 2 10 bar When the tap is on the water flow is at least 10 I min 1 2 bar 6 I min with 1 bar consumption parameters cannot be assure f the water pressure is higher than this a pressure reducing valve must be installed Connection to the tap Connection to the Aqua Stop Aqua Secure Standard machine no necessary with Aqua Stop fixed installation Take the hoses out of the holders Aqua Stop Aqua Secure Aqua Secure Standard Remove all 4 screws completely 1 Connect the water inlet hose hoses to the tap taps 3 4 26 4 mm and to the solenoid valves Caution only tighten the screw connections by hand 2 Open the water tap taps carefully checking the leak tightness of the connection points Caution the screw connection is under mains water pressure Connection in case of hot water models COLD Cold water HOT Hot water max 60 C red If no hot water connection is present ay connect the cold
9. ed to frost or outdoors The washing machine could be damaged Do not lift the appliance by protruding components e g the washing machine door the cover the front panel or the outer door in case of deco models n addition to the instructions provided in this document special regulations from the relevant water and electric utility companies may apply Ifin doubt have a technician connect the appliance Lay hoses and cables in such a way that there is no risk of tripping Installation surface The machine must be stable so that it does not move around The installation surface must be firm and level Soft floors floor coverings are not suitable Installation on a pedestal A N The feet of the washing machine must be secured with holding brackets order no WMZ2200 WX9756 CZ110600 Z7080X0 i Installation on a wood joist floor If possible place the washing machine in a corner Screw a water resistant wooden board min 30 mm thick to the floor The feet of the washing machine must be secured with holding brackets order no see above Installation on a platform with drawer order no WMZ20490 WZ20490 Installing the appliance f Install the appliance before connecting it to the power supply Installation in a kitchenette underneath the worktop or fitted in a cabinet Recess width of 60 cm required Only install the washing machine
10. lug fits the socket E Transportation e g when moving home 6 Me cross section is adequate Weight 66 73 kg depending on model E a specifications nasua aaa aaa 6 ee E After sales service u a aaa 7 the earthing system is properly installed ee i a og j 7 Mains connection Nominal voltage 220 240 V 50 Hz Aqua Stop warranty 0 ce eee T If this is necessary the mains cable may only be replaced by a qualified Nominal current 10 A eee en Re K T Tea Nominal power 2 300 W eplacement mains cables are available from the after sales service m j s Water pressure 200 1000 kPa 2 10 bar Do not use multiple plugs couplings or extension cables O Sama a _ LO m lf a residual current circuit breaker is used only use a type which displays this co Read these instructions before switching on the washing machine symbol x o Also observe the separate Instruction manual Only this symbol guarantees compliance with the currently applicable regulations Keep all documents for use in the future or for the subsequent owner O Do not plug in or unplug the mains plug with wet hands D a Pull the appliance plug out of the socket at the plug only not by the cable 3 Manufacturer gt Operating instructions Safety instructions The washing machine is heavy take care when lifting Caution frozen hoses may rip burst Do not install the washing machine in areas expos
11. ot rectify the fault yourself Operating instructions What to do if page 77 please contact our after sales service We will always find a suitable solution and will avoid a _ _ l Washing machine visit from a service technician wherever possible The contact details for all countries can be found in the enclosed after sales service directory Please give the after sales service the product number E Nr and the production number FD of the appliance You will find this information on the inside of the washing machine door on the opened service flap or at the rear of the appliance depending Product number Production number 2 the model Rely on the professionalism of the manufacturer Please contact us This will ensure that the repair is carried out by trained service technicians who arrive equipped with genuine spare parts for your appliance Aqua Stop warranty only for appliances with Aqua Stop Installation In addition to warranty claims against the vendor from the purchase agreement and to our instructions appliance warranty we will pay damages under the following conditions 1 Ifa fault in our Aqua Stop system causes water damage we will reimburse damages caused to private customers 2 The liability guarantee is valid for the service life of the appliance Ee Ey ESD oF Fa Bravyaka E 3 Itisa prerequisite of all warranty claims that the appliance with Aqua Stop must have
12. ransportation the transport braces must be removed page 3 set up and connected correctly in accordance with our instructions this also includes a E e 3 e i i p 1 npe correctly fitted Aqua Stop extension original accessories seer A R ee i o prevent unused detergent from flowing straight into the drain during the next wash Pour Our warranty goes not cover defective power cables or fittings between the Aqua Stop ALON SUMACE 2 ee ee eee The washing machine must only be connected to an alternating current via a 2 litres of water into compartment II and start the Empty programme connection and the tap Installing the appliance 0 cee eee ee 1 properly installed earthed socket i 2 E Scope of delivery The power supply and voltage indicated on the washing machine rating plate 4 Appliances with Aqua Stop do not need to be supervised during operation nor secured B oca aad cab lengths pe D must be the same afterwards by turning off the tap eee 3 T h 7 ifi ti The tap only needs to be turned off if you are away from home for a long period e g for E Removing the transport braces The connected load and fuse required are specified on the rating plate on ecnnica Speci Icatlons several weeks holiday ane CONNECUON s4 2a sadueeeee eda vases IOMEM Sc ae Acn ace eca Glee bead e Ea Mee re that Dimensions width x depth x height 60 x 55x 85 cm E Electrical CONNEC CHOR cian we erinaweast een 5 L the mains p
13. shing machine with a spirit level and adjust if necessary z y washing machine door on the opened service Preparing and installing transport braces flap or at the rear of the appliance depending Product number Production number 2 the model Rely on the professionalism of the manufacturer Please contact us This will ensure that the repair is carried out by trained service technicians who arrive equipped with genuine spare parts for your appliance 1 Remove all covers and store them a back 07 0 Warran ty only for appliances with Aqua Stop C Installation In addition to warranty claims against the vendor from the purchase agreement and to our instructions appliance warranty we will pay damages under the following conditions 3 Tighten the lock nut against the housing In doing so hold the foot tight and do not adjust its height Caution the lock nuts on all four appliance feet must be screwed tightly against the housing 2 Affix all transport braces In doing so turn the bend on the hose holders inwards Clamp the mains cable in the holders Tighten the screws 1 If a fault in our Aqua Stop system causes water damage we will reimburse damages caused to private customers 2 The liability guarantee is valid for the service life of the appliance 3 It is a prerequisite of all warranty claims that the appliance with Aqua Stop must have been Contents Page Electrical connection After t
14. the first time make sure that you completely remove transport braces and keep them for subsequent transportation Ifyou need to transport the appliance at a later date always re affix the transport braces to prevent damage to the machine page 6 Store the screw and sleeve together 1 Take the hoses out of the holders 2 Remove all 4 screws completely 3 Remove all 4 transport braces completely and take the mains cable out of the holders depending on model 4 Affix the covers WEI a connection 021012141011010 K0 1 1110102 Risk of electric shock Do not immerse the Aqua Stop safety device in water contains an electric valve To prevent leaks or water damage observe the instructions in this section Caution only operate the washing machine using cold drinking water in case of models featured for hot water maximum temperature 60 C Do not connect to the mixer tap of an unpressurised hot water boiler Do not use a used inlet hose Only use the inlet hose supplied or one which was purchased from an authorised specialist dealer Ifin doubt have a technician connect the appliance WE connection 027012141011410 R01 11101021 Water inlet Caution do not bend squash modify or cut through otherwise its strength is no longer guaranteed Optimum water pressure in the supply network 200 1 000 kPa 2 10 bar When the tap is on the water flow is at least 10 I min
15. underneath a continuous worktop that is securely connected to adjacent cabinets M Installation underneath the worktop Risk of electric shock Instead of the appliance covering plate you must have a metal cover order no WMZ20331 WZ20331 Recess width of 60 cm required Moisture inside the drum is due to final testing Scope of delivery depending on model Aqua otop Hot water Aqua secure amp standard Mains cable Water outlet Water inlet Elbow for fixing the drainage y hose in place Adapter 1 2 3 4 depending on model Covers Also required depending on the connection 1 hose clamp 24 40 mm exclusive dealers to connect to a siphon page 4 water connection Useful tools Spirit level for installation Wrenches WAF 13 for loosening transport braces gt page 3 and WAF 17 for aligning appliance feet page 5 Hose and cable lengths 027012141011010 K0 1 1010102 f Available from specialist dealers the after sales service Extension for Aqua Stop or cold water inlet hose approx 2 50 m order no WMZ2380 WZ10130 CZ11350 Z7070X0 Longer inlet hose approx 2 20 m for standard model Removing the transport braces Water CONNECTION cepending on model gt Le Wa ter connec ti ON depending on moael Caution do not bend or pull lengthways A Affix the covers Before using the applian
16. water inlet hose an cover the hot water connection on the appliance so that it is kept free of dirt Remove all 4 transport braces completely and take the mains cable out of the holders depending on model Water outlet Height difference between the installation surface and the Risk of electric shock Do not immerse the Aqua Stop safety device in water drain contains an electric valve min 60 cm max 100 cm To prevent leaks or water damage observe the instructions in this section Caution only operate the washing machine using cold drinking water in case of models i i featured for hot water maximum temperature 60 C Outlet in a sink Do not connect to the mixer tap of an unpressurised hot water boiler Caution secure the drain hose from slipping out _ Do not use a used inlet hose Only use the inlet hose supplied or one which was Caution the plug must not block drainage from the sink During purchased from an authorised specialist dealer pumping check whether the water is draining away quickly Ifin doubt have a technician connect the appliance enough The end of the drain hose must not be immersed in the water pumped out This risks water being sucked back into the washing machine Drainage into a siphon Caution the connection point must be secured with a hose clamp 24 40 mm exclusive dealers Alignment AN es Aligning the washing machine with a spirit level
Download Pdf Manuals
Related Search