Elo Touch Solution 7001L+ECMG2 i5 w/ Win7
Contents
1. 3201L 4201L 5501L 7001L Images of monitor back I O ports with OSD remote HEADPHONE OUTPUT AUDIO LINE IN gt 2 77 ae EE EE aah top Op 1 of ek O efe 1 TOUCH USB i DISPLAY PORT a4 b mar 6 User Manual Interactive Digital Signage SW601990 Rev F Page 6 of 36 IDS Touchmonitor Connections to an External Computer 1 Connect the HDMI cable between the monitor and the video source 2 Connect the USB touch cable between the monitor and the PC 3 Select the correct power cable for your region Connect it between the AC power source and the touchmonitors POWER IN connector 4 The touchmonitor ships in an ON state Use the remote OSD to access the On Screen Display Menu User Manual Interactive Digital Signage SW601990 Rev F Page 7 of 36 Installing the IDS Touchscreen Technology Software Drivers The Elo touch driver and the Elo Computer Module driver packs are available with the CD that ships with the touchmonitor Visit the Elo Touch Solutions website www elotouch com for e Updates to the Elo touch driver e Additional touch driver information e Detailed touch driver installation guides e Touch drivers for other operating systems IntelliTouch Plus units are HID compatible but will require the El2. Thermal Protection Thermal Protection Monitor Mode Step 1 Mode Step 2 Size Disabled C Disabled C ET32 4201L 55 60 ET5501L 53 56 ET7001L 45 50 User Manual Interactive Digital Signage SW601990 Rev F Page 24 of 36 If Thermal Protection Mode Step 2 is reached the internal temperature needs to first decrease back to the Step 1 temperature and then decrease further to the value required to disable Thermal Protection Mode 1 Example of Thermal Protection Mode for an ET4201L Monitor with 100 Brightness At Step 1 OSD 60 Brightness 80 Normal operation returns if OSD can maintain 55 C or lower temperature for five minutes At Step 2 OSD 65 Brightness 72 Return to Step 1 if OSD can maintain 60 C or lower temperature for five minutes If the monitors internal temperature continues to rise the monitor will shut off at OSD 70 C Table Top Mode Requirements 1 The Table Top Mode function on the OSD must be enabled if the unit is placed in table top orientation 2 Cooling methods must be put in place in the area below the monitor to prevent the monitor from overheating Consult the Elo website for additional information regarding thermal recommendations for all mounting modes Note The warranty will be void if failure occurs to the monitor in table top mode orientation and the Table Top Mode function is not enabled without adequate cooling methods installed When the monitor is in Tab
3. Linux Foundation 1 1 root hub VirtualBox USB Tablet Future Technology Devices International Ltd FT Ltd FT Future Technology Devices International Elo TouchSystems User Manual Interactive Digital Signage SW601990 Rev F Page 22 of 36 Temperature Control The IDS 01 Series monitors contain a temperature sensor that provides the user with real time temperature readings This reading can be found on the OSD menu by clicking on Other Menu Information System Temperature If the monitor senses temperatures higher than the operating range the monitor will go into Thermal Protection Mode This mode allows the monitor to remain operational during brief periods of use outside of its operating range System Temperature Video Board 35 C 1920x1080 60Hz External Source HDMI www elotouch com Example of OSD showing the Video Board Temperature In Thermal Protection Mode the monitor will reduce the backlight brightness to bring the internal temperature back within operating range While in this mode brightness cannot be increased If the internal temperature decreases below the Thermal Protection Mode temperature for at least five minutes normal operation is resumed The OSD temperature at which the monitor will enter the Thermal Protection Mode is in the table below When the Thermal Protection Mode is enabled the following icon will appear in the Main Menu and the Brightness Menu This will indic
4. Disconnect and remove any I O cables that the digital device does not use Unterminated I O cables are a potential source of high RF emission levels vi Plug the digital device into only a grounded outlet receptacle Do not use AC adapter plugs Removing or cutting the line cord ground may increase RF emission levels and User Manual Interactive Digital Signage SW601990 Rev F Page 32 of 36 may also present a lethal shock hazard to the user If you need additional help consult your dealer manufacturer or an experienced radio or television technician lll Agency Certifications The following certifications and marks have been issued or declared for this monitor Argentina S Mark Japan VCCI Taiwan BSMI Australia RCM Korea KC United States FCC UL Canada CUL IC Mexico CoC China CCC Russia EAC Europe CE IV China RoHS In accordance to Chinese law Administration on the Control of Pollution Caused by Electronic Information Products the section below lists out the name and amount of the toxic and or hazardous materials that this product may contain Component Toxic or Hazardous Substances and Elements Name Lead Pb Mercury Hg Cadmium Cd Hexavalent Polybrominated Polybrominated Chromium Biphenyls PBB Diphenyl Cr6 Ethers PBDE Plastic Parts O O O O O Metal Parts X O O O O O Wire and X O O O O O Cable Assembly LCD Panel X O O O O O Touch Screen X O O O O
5. User Manual Interactive Digital Signage SW601990 Rev F Page 2 of 36 Table of Contents Chapter 1 00 6 0 4 Chapter 2 8681 6 0 0 06 5 Chapter 3 Touchmonitor Installation 6 Chapter 4 10 6 GR Ge Ge 5 9 Chapter 5 Operation 9 9 6 99 99 9 13 Chapter 6 Technical 5 60 28 Chapter 7 Safety 8 131 1 8 6 29 Chapter 8 Regulatory Information 30 Chapter 9 Warranty Information 35 User Manual Interactive Digital Signage SW601990 Rev F Page 3 of 36 Chapter 1 Introduction Product Description Your new Interactive Digital Signage IDS touchmonitor combines Elo Touch Solutions reliable performance with the latest developments in touchscreen technology and display design This combination of features creates a natural flow of information between a user and the touchmonitor
6. USER MANUAL Elo Touch Solutions ET3201L 32 Interactive Digital Signage Touchmonitor ET4201L 42 Interactive Digital Signage Touchmonitor ET5501L 55 Interactive Digital Signage Touchmonitor ET7001L 70 Interactive Digital Signage Touchmonitor SW601990 Rev F Copyright 2014 Elo Touch Solutions Inc All Rights Reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means including but not limited to electronic magnetic optical chemical manual or otherwise without prior written permission of Elo Touch Solutions Inc Disclaimer The information in this document is subject to change without notice Elo Touch Solutions Inc and its Afffiliates collectively Elo makes no representations or warranties with respect to the contents herein and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes Trademark Acknowledgments AccuTouch CarrollTouch Elo Elo logo Elo Touch Elo Touch Solutions Elo TouchSystems IntelliTouch iTouch SecureTouch TouchTools and VuPoint are trademarks of Elo and its Affiliates Windows is a trademark of Microsoft Corporation
7. Provide information about help and support System Temperature Provides the system Temperature information If the Elo computer module is inserted there will be a secondary line showing that temperature information Adjusts how long a period of OSD button inactivity the Touchmonitor will wait before OSD Timer closing the OSD The adjustable range is between 5 and 60 seconds Default 15 seconds User Manual Interactive Digital Signage SW601990 Rev Page 18 of 36 Selects which language the OSD information is displayed in The available OSD languages are English French Italian German Spanish Simplified Chinese Language Traditional Chinese and Japanese Default English OSD Moves the OSD location left and right on the display H Position Default 50 centered OSD Moves the OSD location up and down on the display V position Default 50 centered Recalling Selecting Recall Defaults restores all factory default settings for OSD adjustable Defaults parameters except OSD Language and OSD Position and for Preset Video Mode timings MDC Protocol This menu allows the user to switch between the serial protocol and the DDC CI protocol DDC CI protocol is used to communicate to a host computer via the video signal Tabletop Enables or disables the Tabletop Thermal Protection Mode settings Displays Monitor Information System Temperature and Help amp Support options informa
8. O Panel PCBA X O O O O O Software CD O O O O O O etc O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this component is below the limit requirement in SJ T11363 2006 X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this component is above the limit requirement in SJ T 11363 2006 For items marked with X exemptions were taken according to EU RoHS User Manual Interactive Digital Signage SW601990 Rev F Page 33 of 36 Explanation of Markings 1 In accordance with the SJ T11364 2006 requirement the electronic information products are marked with the following pollution control logo The Environment Friendly Use Period for this product is 10 years The product will not leak or mutate under normal operating conditions listed below so that the use of this electronic information product will not result in any severe environmental pollution any bodily injury or damage to any assets Operating Temperature 0 40 Humidity 20 80 non condensing Storage Temperature 20 60 Humidity 10 90 non condensing 2 It is encouraged and recommended that this product be recycled and reused according to local laws The product should not be thrown away casually A CD Chapter 9 Warranty Information For warranty information go http www elotouch com Support warranty
9. This touchmonitor incorporates a 24 bit color active matrix thin film transistor and digital signage LCD panel to provide superior display performance Its Full HD resolution of 1920x1080 is suitable for displaying graphics and images Other features that enhance this LCD monitor s performance are Plug amp Play compatibility built in soeakers and headphone output capability a remote for on screen display OSD controls and a family of IDS computer modules The computer modules are designed to slide into a bay on the rear of the monitor The monitors form factor will not be affected and extra cabling is not required Your IDS touchmonitor will turn into an IDS All in One touchcomputer Precautions Follow all warnings precautions and maintenance as recommended in this user manual to maximize the life of your unit and prevent risks to user safety See Chapter 8 for more information on touchmonitor safety For your health and safety it is strongly recommended that at least two people four for the ET7001L handle lift and or move these touchmonitors This manual contains information that is important for the proper setup and maintenance of the IDS and optional computer module Before setting up and powering on your new touchmonitor and computer module read through this manual especially the Installation Mounting and Operation chapters User Manual Interactive Digital Signage SW601990 Rev F Page 4 of 36 Chapter 2 Unpackin
10. asp User Manual Interactive Digital Signage SW601990 Rev F Page 35 of 36 Check out our website www elotouch com Get the latest e Product Information Specifications Upcoming events Press releases Software drivers Getting in Touch with Us To find out more about the extensive range of Elo touch solutions visit our website at www elotouch com or simply call the office nearest you North America Tel 800 ELO TOUCH Europe Asia Pacific Latin America Elo Touch Solutions Tel 1 408 597 8000 Tel 32 0 16 70 45 00 i 21 3329 Tel 786 923 0251 1033 McCarthy Blvd Fax 1 408 597 8001 Fax 32 0 16 70 45 49 fae 21 3329 Fax 305 931 0124 Milpitas CA 95035 customerservice elotouch com elosales elotouch com www elotouch cn www elotouch com ar Copyright 2014 Elo Touch Solutions Inc All rights reserved User Manual Interactive Digital Signage SW601990 Rev F Page 36 of 36
11. aste It should be deposited at a facility that enables recovery and recycling game Flo has put in place recycling arrangements in certain parts of the world For information on how you can access these arrangements please visit http www elotouch com AboutElo ewaste program User Manual Interactive Digital Signage SW601990 Rev Page 30 of 36 Chapter 8 Regulatory Information I Electrical Safety Information Compliance is required with respect to the voltage frequency and current requirements indicated on the manufacturer s label Connection to a different power source than those specified herein will likely result in improper operation damage to the equipment or pose a fire hazard if the limitations are not followed There are no operator serviceable parts inside this equipment There are hazardous voltages generated by this equipment which constitute a safety hazard Service should be provided only by a qualified service technician Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment to mains power ll Emissions and Immunity Information Notice to Users in the United States This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipmen
12. ate that the Thermal Protection Mode is active Icon showing that Thermal Protection Mode is active User Manual Interactive Digital Signage SW601990 Rev F Page 23 of 36 t Audio Menu Color Menu Other Menu Exit 1920x1080 60Hz Module com Light Sensor Brightness On 80 80 p Off NE gt 1920x1080 60Hz Elo Computer Module HDMI www elotouch com t Thermal Protection Mode icon will show on the top corner of these menus indicating that the Thermal Protect Mode is active The user will be prompted to shut off the monitor within sixty seconds if the temperature continues to rise after Thermal Protection Mode Step 2 has been enabled If the system is not manually turned off in sixty seconds the touchmonitor will automatically turn off to prevent permanent damage to the monitor The table below shows the Auto Shut Off temperature Note This will only enable in extreme conditions Portrait and Landscape Mode Monitor Thermal Protection Thermal Protection Auto Shut Off Size Mode C Step 1 Mode C Step 2 Temperature C ET32 4201L 60 65 70 ET5501L 56 61 65 ET7001L 50 55 63 In the event that Thermal Protection Mode Step 1 or 2 has been enabled the monitor will resume full operational capabilities after the OSD temperature decreases to the values set forth in the table below These temperatures must be retained for at least five minutes
13. ation on the drivers do the following User Manual Interactive Digital Signage SW601990 Rev F Page 21 of 36 NOTE The Elo Touch Solutions Touchmonitor ID will be different per touch technology In Mac OS X Open the Terminal window and under Hardware select USB A screen that looks like the image below will appear The available USB devices will be displayed W Hardware USBDevice Tree ATA USB High Speed Bus Audio Built In Y Hub Bluetooth Y USB 2 0 Hub MTT Card Reader Diagnostics Disc Burning Ethernet Cards Fibre Channel FireWire Graphics Displays Hardware RAID Mstar USB Debug Tool USB 2 0 Hub MTT Elo TouchSystems 2515 iTouch Plus USB Touchmonitor FT232R USB UART Composite Device Y BRCM20702 Hub Bluetooth USB Host Controller USB High Speed Bus Memory Hub PCI Cards ADATA USB Flash Drive Parallel SCSI USB Keyboard Power IR Receiver Printers SAS Serial ATA USB High Speed Bus Thunderbolt Host Controller Location Built in USB Host Controller Driver AppleUSBEHCI In Ubuntu versions that support touch Open a Terminal window and type lsusb as the command A screen that looks like below will open The available USB devices will be displayed ubuntu ubuntu ubuntu ubuntu lsusb 001 Device 001 ID 1 001 Device 002 15 1 001 Device 003 ID 0403 USB Serial UART IC 001 Device 004 ID 0403 2232C Dual USB UART FIFO IC Bus 001 Device 005 ID 04e7 ubuntu ubuntu
14. e are planned unplug the AC power cable to save power The maximum voltage frequency and current for the touchmonitor are provided in the power ratings table below Operating Voltage Operating Frequency Operating Current Range Range Range ET32 4201L 100 240Vac 50 60 Hz 3 6 1 5 ET5501L 100 240Vac 50 60 Hz 5 2 1A ET7001L 100 240Vac 50 60 Hz 5 2 1A User Manual Interactive Digital Signage SW601990 Rev F Page 13 of 36 IntelliTouch Touchscreen Technology The IntelliTouch and IntelliTouch Plus touchscreens can be re calibrated to your displayed video image if needed through the calibration function in the Elo driver control panel IntelliTouch Plus monitors require calibration if the video source is rotated Optical Touchscreens Technology When connected to Windows 7 computers the touchmonitor can report six simultaneous touches Projective Capacitance Touchscreens Technology When connected to Windows 7 computers the touchmonitor can report ten simultaneous touches Gesturing Images For multi touch monitors the following gestures are possible Single Touch Gestures and their Functions Swipe The ability to swipe through from one picture to another or drag an icon Dual Touch Gestures and their Functions Swipe The action of moving a finger across the screen The ability to swipe through from one picture to another or drag an icon Pinch Zoom Zoom into a pic
15. e such that it is within the allowable timing ranges specified for your Touchmonitor on the Elo website www elotouch com Touch functionality doesn t work Verify your computer or Elo Computer Module has the latest drivers installed For optical units remove and Elo driver and restart the computer Refer to the Setup chapters for details Technical Assistance Visit www elotouch com go websupport for online self help Visit www elotouch com go contactsupport for technical support See this user manuals last page for worldwide technical support phone numbers User Manual Interactive Digital Signage SW601990 Rev Page 28 of 36 Chapter 7 Safety amp Maintenance Safety To avoid risk of electric shock follow all safety notices and do not disassemble the touchmonitor or Computer Module They are not user serviceable Do not block or insert anything inside any of the ventilation slots The touchmonitor is equipped with a 3 wire grounding power cord The power cord plug only fits into a grounded outlet Do not fit or modify the plug into an outlet that has not been configured for this purpose Do not use a damaged power cord Only use the power cord that came with your Elo Touchmonitor Use of an unauthorized power cord may invalidate your warranty Ensure that the system is maintained and runs within the specified environmental conditions listed in the products specifications available on the Elo Touch Solut
16. eature will act within the limits set forth in the Temperature Control section Video Firmware Upgrade The IDS 01 series touchmonitors contain the ability to update the video firmware with the use of an external computer Contact Elo customer service for information on how to upgrade the video firmware User Manual Interactive Digital Signage SW601990 Rev Page 27 of 36 Chapter 6 Technical Support If you are experiencing trouble with your touchmonitor refer to the following suggestions If the problem persists please contact your local dealer or contact Elo Touch Solutions Customer Service Solutions to Common Problems Problem Suggested Troubleshooting The Touchmonitor does not respond when turning on the system Check that the AC power cable is properly connected Verify the AC power source is functioning The Computer Module does not respond when turning on the system Disconnect the AC power cable and verify that the Computer Module is properly installed Reconnect the AC power cable Monitor display is dim Use the OSD to increase the brightness Use the OSD to increase the contrast Monitor display is blank If the Power Status LED is blinking the monitor or Computer Module may be in SLEEP mode Press any key move the mouse touch the touchscreen to see if the image reappears Monitor displays an Out Of Range message Adjust your computers resolution timing mod
17. ence will not occur in any particular installation due to site specific factors This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 1 In order to meet emission and immunity requirements the user must observe the following a Use only the provided I O cables to connect this digital device with any computer b To ensure compliance use only the provided manufacturer s approved line cord c The user is cautioned that changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 If this equipment appears to cause interference with radio or television reception or any other device a Verify as an emission source by turning the equipment off and on If you determine that this equipment is causing the interference try to correct the interference by using one or more of the following measures i Move the digital device away from the affected receiver ii Reposition turn the digital device with respect to the affected receiver iii Reorient the affected receiver s antenna iv Plug the digital device into a different AC outlet so the digital device and the receiver are on different branch circuits
18. g Unpacking the Interactive Digital Signage Touchmonitor To unpack the IDS follow these steps 1 The carton should be oriented in the manner according to its labeling The hinged plastic locks should be at the bottom 2 Open and remove all 4 hinged plastic locks There are 6 hinged plastic locks for the 7001L unit S S N i 4 With the top lid removed you now have access to the IDS touchmonitor and the included accessories User Manual Interactive Digital Signage SW601990 Rev F Page 5 of 36 Chapter 3 IDS Touchmonitor Installation Connector Panel amp Interfaces Note For your health and safety it is strongly recommended that at least two people four for the ET7001L handle lift or move these Touchmonitors Elo recommends safe lifting techniques as described in OSHA NIOSH Guidelines Check that the following items are present and in good condition e IDS touchmonitor e User Manual CD e Quick Install Guide e OSD Remote connected to the monitor e Cables o HDMI USB North America power Europe Korea power U K power Argentina power Taiwan power China power Korea power Japan power amp Japan 3pin 2pin adapter Remove the cable cover on the bottom rear when viewed in landscape orientation to access the touchmonitors connector panel Pictures of the connector panel and interfaces The OSD connection is in red
19. ions website www elotouch com Environmental conditions for transportation and storage Temperature Portrait and Landscape Mode Operating 0 C to 40 C Storage Transportation 20 C to 50 C Table Top Mode Operating Temperature Independent of altitude 0 C to 35 C Non Operating Temperature Independent of altitude 20 C to 50 C Humidity non condensing Operating 20 to 80 Storage Transportation 10 to 95 Altitude Operating 0 to 3 658m Storage Transportation 0 to 12 192m User Manual Interactive Digital Signage SW601990 Rev Page 29 of 36 Care and Handling The following tips will help maintain optimal performance of your touchmonitor e Disconnect the AC power cable before cleaning e To clean the display use a cloth lightly dampened with a mild detergent e It is important that your unit remains dry Do not get liquids on or inside the unit In the event that liquid does get inside have a qualified service technician inspect the unit before you power it on again 9 Do not wipe the screen with a cloth or sponge that could scratch the surface e When cleaning the touchscreen use window or glass cleaner applied to a clean cloth or sponge Never apply the cleaner directly on the touchscreen Do not use alcohol methyl ethyl or isopropyl thinner benzene or other abrasive cleaners Waste Electrical amp Electronic Equipment Directive WEEE sd This product should not be disposed of with household w
20. isplayPort HDMI and the Computer Module This adjustment selects which of those input ports should be displayed If an Elo Computer Module or Intel OPS computer module has been detected video priority is given to the computer module before any of the external sources Increase decrease monitor brightness Brightness Default 65 Increase decrease monitor contrast center Default 50 Allows user to change the H position V position Clock and Phase Non sings VGA is selected the Auto Adjust feature is available Adjusts sharpness of the displayed images Sharpness Default no sharpness adjustment Sharpness function is disabled when the input source ratio is the same as the panels native ratio Aspect Ratio Switches the scaling method between Fill Screen and Fill to Aspect Ratio Default Fill Screen Fill Screen Scales the X and Y dimensions of the input video up or down as needed to the displays native resolution Fill Aspect Ratio Assuming a landscape orientation and an input video with aspect ratio smaller than 16 9 scales the Y dimension of the input video up or down as needed to the displays Y resolution and scales the X dimension to maintain the aspect ratio and fills the rest of the display with equal black bars on the left and right When the input source ratio is the same as the panel native ratio this function is disabled Direct output Input source is the same with output s
21. le top mode the Thermal Protection steps are different These OSD values are stated in the table below Thermal Protection Thermal Protection Thermal Protection Auto Shut Off Monitor Mode Enabled C Mode Enabled C Mode Enabled C Temperature C Size Step 1 Step 2 Step 3 ET32 4201L 60 65 70 75 ET5501L 57 61 n a 65 ET7001L 59 64 69 74 User Manual Interactive Digital Signage SW601990 Rev F Page 25 of 36 Intelligent Brightness Control The IDS 01 touchmonitors include a light sensor that adjusts the brightness of the screen in accordance with the ambient light level surrounding the monitor The Intelligent Brightness Control functions based on the following curve ET3201L Brightness vs Ambient Light 0 5 2 5 O 70 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 Ambient Light nits ET4201L Brightness vs Ambient Light 120 100 80 60 9 9 o 2 a 40 20 0 O 60 100 140 190 220 250 300 350 360 370 400 420 440 460 480 500 Ambient Light nits User Manual Interactive Digital Signage SW601990 Rev F Page 26 of 36 ET5501 7001L Brightness vs Ambient Light 0 9 9 lt D a 0 50 70 90 150 200 250 275 300 350 400 410 420 430 460 480 500 Ambient Light Note If the Thermal Protection Mode is activated the Intelligent Brightness Control f
22. monitor The VESA FDMI compliant mounting is coded VESA MOUNT PER MIS F 600 600 6MM For the 70 models A four hole 400x400mm mounting pattern is provided on the rear of the monitor The VESA FDMI compliant mounting is coded VESA MOUNT PER MIS F 400 400 8MM Refer to www elotouch com for dimensional drawings User Manual Interactive Digital Signage SW601990 Rev F Page 11 of 36 Optional Stand for 3201L and 4201L Only Elo PN E455084 User Manual Interactive Digital Signage SW601990 Rev F Page 12 of 36 Chapter 5 Operation Power To turn the touchmonitor on or off press the touchmonitor power button once If a computer module is installed then the computer module will also turn on with the monitor To abruptly power off the computer module and touchmonitor press and hold the touchmonitor power button until the computer shuts off To gracefully shut down the computer module follow the computer modules operating systems normal power off procedure A Power Status LED is provided on the OSD Remote that functions according to the following table Touchmonitor Computer Module status LED status SLEEP BLINKING The system consumes low power when in SLEEP and OFF modes For detailed power consumption specifications refer to technical specifications available on the Elo website www elotouch com Touching the screen will bring the system out of MONITOR SLEEP mode If long periods of disus
23. n the following location RFID tags can be read at a distance of up to 40 mm away from the bezel User Manual Interactive Digital Signage SW601990 Rev Page 20 of 36 For best results touch the tag directly to the bezel area containing the antenna Driver Installation Elo Computer Modules ECMG2 i3 or i5 have all required drivers preinstalled All required drivers are available online at www elotouch com If drivers are to be installed from the included CD an external CD Rom drive is required For No Operating System OS units the drivers are provided on the accompanying driver CD and are available online at www elotouch com For Windows Operating Systems After the computer finishes booting up follow these instructions to install the drivers Attach the external CD Rom drive to the monitor and turn the computer on Insert the drivers CD After the OS has booted right click on My Computer Click on Manage Click on Device Manager Highlight one of the devices that has a warning label and click Update Driver Click the option Browse My Computer for Driver Software Choose the path to your CD Rom drive and click Next Let the device software component be installed and then proceed to the next device Do this for all of the devices that have the warning label For Mac OS X higher these drivers are automatically installed when the system is connected to the monitor To find inform
24. o driver if touch calibration is required Optical units are HID compatible and do not require an Elo touch driver If an Elo touch driver has previously been installed on the host computer remove this driver by opening Control Panel and selecting to remove the driver completely User Manual Interactive Digital Signage SW601990 Rev F Page 8 of 36 Chapter 4 Mounting Note For your health and safety it is strongly recommended that at least two people four are recommended for the ET7001L handle lift or move these touchmonitors Note Do NOT lay the display face down as this can cause damage to the monitor General Mounting Information The following three mounting orientations are supported Landscape portrait and table top mode For optimal touch performance ensure that the monitor is supported fully and is as flat as possible Portrait User Manual Interactive Digital Signage SW601990 Rev F Page 9 of 36 Landscape Table Top Refer to the Temperature Control section for table top mode requirements User Manual Interactive Digital Signage SW601990 Rev F Page 10 of 36 Rear VESA Mount For the 32 and 42 models A four hole 400x400mm mounting pattern is provided on the rear of the monitor The VESA FDMI compliant mounting is coded VESA MOUNT PER MIS F 400 400 6MM For the 55 models A four hole 600x600mm mounting pattern is provided on the rear of the
25. oss of fidelity is most apparent when viewing feature rich images at close distances for example images containing small font text Your touchmonitor will likely not require video adjustments However for analog VGA video variations in video graphic card outputs may require touchmonitor adjustments through the OSD to optimize the quality of the touchmonitors displayed image To reduce the need for adjustments for different video mode timings the monitor correctly scales and displays some of the video industries most common video timing modes User Manual Interactive Digital Signage SW601990 Rev F Page 15 of 36 On Screen Display OSD Connected Through the RJ45 Connection Five OSD buttons can be found on the OSD remote There is an LED light which shows the current state of the monitor The S are the functions that relate to the designated button MENU SELECT 5 The buttons and their functionality are Button Function when OSD is not displayed Function when OSD is displayed Menu Display OSD main menu Return to previous OSD menu Decrease value of selected parameter lt Display OSD Audio source submenu select previous menu item Increase value of selected parameter select next menu item Select parameter for adjustment select submenu to enter gt Hot key for changing video source Select Display Audio and Video Parameters Menu Power for the monitor Toggles the power sta
26. ource and the image will be on the center of the screen No Scaling will occur Recalibration may be required when switching between these options Light Sensor The light sensor can be toggled on or off When the light sensor is enabled the brightness cannot be changed manually Auto Adjust Automatically adjusts the system clock to the input analog VGA video signal affecting the H position V position Clock and Phase menu items Not applicable when using HDMI video or the Computer Module User Manual Interactive Digital Signage SW601990 Rev F Page 17 of 36 Allows fine adjustments of the panels pixel dot clock sas Not applicable when using HDMVDisplayPort video or the Computer Module Phase Allows fine adjustments of the panels pixel dot clock phase Not applicable when using HDMI DisplayPort video or the Computer Module Moves the image horizontally on the display in single pixel increments H position Default centered Not applicable when using HDMI DisplayPort video or the Computer Module Moves the image vertically on the display in single pixel increments V position Default centered Not applicable when using HDMI DisplayPort video or the Computer Module The user can choose between Standard 5 10 or 15 black level offset Black Level The saturation level of the colors change according to the chosen black level offset Not available when the video source is from VGA Selects the dis
27. peakers See the Audio Source OSD parameter for details When headphones are plugged into the headphone output jack the internal speakers turn off and audio is played over the headphones Volume and muting of the speaker and headphone outputs can be controlled by the OSD MDC Functionality For Remote Monitor Applications The touchmonitor has the ability to allow remote access from a host application This is done through the use of the Multiple Display Control command sets By installing the IDS Utilities Suite the user can communicate with the monitor via the application The host application can send a variety of different instructions which will be executed on the IDS 01 series touchmonitor For detailed information refer to the utilities suite user guide RFID Functionality For 3201L and 4201L Units There is an integrated RFID antenna within the monitor To enable the RFID functionality a RFID reader module available at www elotouch com must be installed and connected to the integrated monitor antenna Refer to the RFID peripheral installation guide for proper hardware and software installation techniques For the 5501L and 7001L units an external peripheral kit is available from Elo The list of RFID protocols that can be read are elSO 14443 A elSO 14443 B elSO 15693 The RFID features Peer to Peer applications and the Read and Write functionality The location of the RFID antenna is indicated by the arrow i
28. plays color temperature The available color temperatures are 9300K 7500K 6500K 5500K and User Defined If the User Defined option is selected the olor eg ae Temperature user can change the color temperature by changing individual R G and B gains ona scale from 0 to 100 Default User Defined with R G and B all set to 100 Audio Source Allows the user to choose the audio source The choices are From Video Source Line in and ECM Line in available only if an ECM is detected If there is no Computer Module plugged in and the video source is HDMI the options are Line In and HDMI Default Line In Color Adjust The Color Temperature menu can be chosen or Hue and Saturation can be varied in this menu Color Temperature will only be available in the Standard color preference mode Hue and Saturation are available in the remaining color preferences Standard Movie Gaming Photo modes can be chosen depending on the users Color preference Preference Movie Gaming and Photo mode allow the user to vary the Hue and Saturation Default Standard OSD menu The Horizontal position vertical position and OSD timer can be changed from here Language Settings can be changed Recall Defaults set the system back to the preset standards Information display information about the monitor and system Other Menu MDC Protocol allows the user to choose between DDC CI and RS232 mode for the MDC utility Support amp Help
29. t generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Notice to Users in Canada This equipment complies with the Class A limits for radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrial Canada Notice to Users in the European Union Use only the provided power cords and interconnecting cabling provided with the equipment Substitution of provided cords and cabling may compromise electrical safety or CE Mark Certification for emissions or immunity as required by the following standards This Information Technology Equipment ITE is required to have a CE Mark on the Manufacturer s label which means that the equipment has been tested to the following Directives and Standards This equipment has been tested to the requirements for the CE Mark User Manual Interactive Digital Signage SW601990 Rev Page 31 of 36 as required by EMC Directive 2004 108 EC as indicated in European Standard EN 55022 Class A and the Low Voltage Directive 2006 95 EC as indicated in European Standard EN 60950 1 General Information to all Users This equipment generates uses and can radiate radio frequency energy If not installed and used according to this manual the equipment may cause interference with radio and television communications There is however no guarantee that interfer
30. tion Nothing is adjustable in this menu Monitor Displays the touchmonitor model and the monitor and touchscreen serial Information information System Displays the real time temperature of the Video Board l l Temperature Note Docking Board and the CPU Sensor temperatures are only available if these features are supported by the computer module Help amp Display information regarding Elo Touch Solutions contact information Support All touchmonitor adjustments made through the OSD are automatically memorized as soon as they are entered This feature saves you from having to reset your choices every time the touchmonitor is unplugged or powered off and on or if there is a power failure OSD and Power Lockouts Press and hold the Menu and gt buttons for one seconds to enable disable the OSD Locking feature When the OSD Locking is enabled pressing any of the Menu Up Down or Select keys will have no effect on the system Press and hold the Menu and lt buttons for one seconds to enable disable the Power Locking feature When the Power Locking is enabled pressing the power switch will have no effect on the system User Manual Interactive Digital Signage SW601990 Rev F Page 19 of 36 Audio Audio from the touchmonitor Line In touchmonitor HDMI touchmonitor DisplayPort computer module Line In or computer module HDMI or DisplayPort ports can be played over the touchmonitors internal s
31. ture Place two fingers on the screen and move them closer together to zoom in Move your fingers away from each other to zoom out Before zoom After zoom User Manual Interactive Digital Signage SW601990 Rev F Page 14 of 36 Rotate A picture can be rotated 360 ik 6 AK In addition to the above gestures Optical units have the ability to pinch and zoom three different pictures at the same time because six simultaneous touches are supported Video LCD panels native resolution is its width and height measured in number of pixels In almost all cases an image displayed on an LCD monitor will look best when your computers output resolution matches the LCD panels native resolution See the display specifications on the Elo website www elotouch com to find your touchmonitors native resolution Operating in other resolutions will degrade video performance and is not recommended For computer output resolutions at non native resolutions the monitor will scale the video to panel s native resolution For smaller input video resolutions this involves stretching the input image in the X and Y dimensions to fit the panel For larger input video resolutions this involves compressing the input image in the X and Y dimensions to fit the panel An unavoidable byproduct of the scaling algorithms is a loss of fidelity when the computers output video image is scaled by the monitor to fit the display This l
32. tus of the monitor The hot key allows the user to quickly change the input video source If the user accidently presses this key they can quickly press the Menu button to cancel a video source change Using the OSD buttons controls an on screen graphical user interface which displays on top of your input video allowing intuitive adjustment of the following display parameters User Manual Interactive Digital Signage SW601990 Rev F Page 16 of 36 Parameter Available Adjustment Main Menu Video Settings Audio Settings Color Settings and Other Settings can be selected Video Menu Video Source Brightness Contrast Black Level Sharpness and Aspect Ratio are available in this menu Video Source Allows the user to switch between the available video sources Allows the user to toggle the mute setting Also the volume of the internal speakers or Audio Menu headphones can be adjusted Default Not Muted Volume at 50 Color Menu Displays the Color Adjust and Color Preference Menus HDMI Allows HDMI video to be displayed on the monitor VGA Port Allows VGA video to be displayed on the monitor DisplayPort Allows DisplayPort video to be displayed on the monitor Elo Computer ECM DP DisplayPort is the standard video output of Elo Computer modules If Module HDMI video input is found the video source can be switched Video Source The monitor continually scans for active video from VGA D
Download Pdf Manuals
Related Search