3M Multi-touch Display C2254PW (22")
Contents
1. Important Notes e In extreme temperature and humidity situations you may observe condensation between the touch screen and the display To minimize this condition place the unit where it will be used and allow a 24 hour environmental stabilization period prior to powering on the display Any noticeable condensation 1s temporary and will have no long term affect on the operation of the display e You are cautioned that any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment e When unplugging the power supply cord hold the plug do not pull by the cord e Do not connect or disconnect this product during an electrical storm e Remember to take into account that the operating temperature of the installation may be greater than the room ambient and consideration should be given to installing the unit in an environment compatible with the maximum rated operating temperature Specifications can be found in the product data sheet on the 3M Touch Systems website at http www 3m com touch e When installing the unit ensure that it does not restrict the flow of air to any other equipment within the installation required for safe operation e An inherent characteristic of the PCT sensor is a fine grid pattern that may be visible under certain lighting conditions e Install the display in a well ventilated area Always maintain adequate2. 3M Multi Touch Chassis Display User Guide Multi Touch Controllers ccccccccccecceccecccccccccccceccecceceecasceccuscesceecsesceseeseeseeseesees 25 Troubleshooting amp Maintenance Display Installation Problems eee ene enn ED Seen ene es E eo ene nn ee 26 Troubleshooting the Touch SCMCOL occ occce yan tcc caecearenette te cnans sous saat santa setsasatae 21 Power Manap omeNi essesi en e EE E EE eE aa 28 Regulatory Information Regulatory Agency ApPprovdlS csccssecscseccsecsasecectecconsscesesasateasessones ae Dia ii iiini 29 E A N E e EE E E EEE 30 CE Conformity for EUTOP O serso iaa a aaie 30 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 5 Overview CHAPTER 1 Introduction Congratulations on the purchase of your 3M Touch Systems Multi Touch Chassis display This guide describes how to set up your 3M Multi Touch Chassis Display The 3M Touch Systems product line of chassis displays offers the Multi Touch Chassis Display for kiosk ATM and industrial enclosures All Multi Touch Chassis Displays are encased in rugged metal instead of plastic These displays feature a touch sensor interface several mounting options and sturdy construction The Multi Touch Chassis Display 1s a 22 LCD with 16 10 aspect ratio 3M Multi Touch Technology based on 3M projected capacitive touch technology and electronics offers fast and accurate multi touch tou
3. 3M Multi Touch Chassis Display User Guide Models C2254PW and C2234PW Read and understand all safety information contained in this document before using this product 2 3M Multi Touch Chassis Display User Guide The information in this document is subject to change without notice No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of 3M Touch Systems Inc 3M may have patents or pending patent applications trademarks copyrights or other intellectual property rights covering subject matter in this document The furnishing of this document does not give you license to these patents trademarks copyrights or other intellectual property except as expressly provided in any written license agreement from 3M Touch Systems Inc The information provided in this document is intended as a guide only For the latest detailed engineering specifications please contact your 3M Touch Systems Inc Application Engineer 3M Touch Systems Inc is committed to continually improving product designs as a result product specifications may be subject to change without notification ROHS 2011 65 EU means that the product or part does not contain any of the substances in excess of the maximum concentration values MCVs in EU RoHS Directive 2011 65 EU unless the substance is in an application that is exempt under EU RoHS
4. Inc provides extensive support services through our website and technical support organization Visit the 3M Touch Systems website at http www 3m com touch where you can download MT 7 software and drivers obtain regularly updated technical documentation on 3M Touch Systems products and learn more about our company Whenever you contact Technical Support please provide the following information e Touch display size part number and serial number e Current driver version e Operating system used e Information on additional peripherals Technical Support is available Monday through Friday 8 30 a m to 5 30 p m with limited call back service after 5 30 p m until 8 00 p m US Eastern Standard Time 9 a m to 5 p m throughout Europe You can contact 3M Touch Systems Inc Technical Support US only Eastern Standard Time by calling the hot line sending email or a fax e Technical Support Hot Line 978 659 9200 e Technical Support Fax 978 659 9400 e Toll Free 1 866 407 6666 Option 3 e Email US TS techsupport mmm com Contact 3M Touch Systems Contact information for all offices can be found on our website at http www 3m com touch 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 11 CHAPTER 2 Setting up Your Multi Touch Chassis Display This chapter describes how to set up your 3M Touch Systems Multi Touch Chassis Display You need to complete the
5. and securely to the display and the computer e Check that the video cable is connected properly and securely to the display and the computer e Check that no pins are bent in the video cable connector e The video display adjustments are incorrect Refer to Chapter 2 for adjusting procedures Troubleshooting the Touch Sensor If you are experiencing problems with the touch sensor check the following list of common installation errors Table 22 Common Touch Sensor Installation Issues Common Installation Issues Possible Solutions Touch sensor does not respond e Review the installation procedures Are all cables connected to touch Touch sensor is not accurate properly e After you installed Touch Software did you restart your PC to activate the touch sensor driver e Remove the sensor communications cable and plug it back in e Disconnect the power cable and plug it back in e Calibrate the touch sensor for the current video resolution and operating system Refer to the Video Alignment section in Chapter 3 for additional information 3M Touch Systems Inc Proprietary Information TSD 37732F 28 3M Multi Touch Chassis Display User Guide Common Installation Possible Solutions Issues Cursor does not follow finger e Calibrate the touch sensor for the current video resolution and movement or does not reach operating system Refer to the Video Alignment section in Chapter 3 the edges of the sensor for addi
6. paint calibration for optimum accuracy for your touch display Calibrate D a If you are writing your own drivers you should provide your own video alignment tool Use the Paint program Start gt Programs gt Accessories gt Paint to determine if you have multi touch operation Retest the accuracy after you perform a calibration Multi Touch Controllers Refer to the 3M Multi Touch PX4nn ASIC Controller Reference Guide TSD 40847 for additional details on your controller 3M Touch Systems Inc Proprietary Information TSD 37732F 26 3M Multi Touch Chassis Display User Guide APPENDIX A Troubleshooting amp Maintenance If you have a problem setting up or using your display you may be able to solve it yourself Before calling 3M Touch Systems try the suggested actions that are appropriate to the problems you are experiencing with the display You may also want to consult your video card user s manual for additional troubleshooting advice Display Installation Problems Table 21 Common Display Installation Issues Issue Solution No image displayed blank gx the display receiving power screen Check that the computer s power cable is connected properly and securely into a grounded electrical outlet Check that the AC input jack is firmly plugged into the display Check that the display s power cable is connected properly and securely to an electrical outlet Try using a differ
7. ventilation to protect the display from overheating and to ensure reliable and continued operation e Do not expose this display to direct sunlight or heat Passive heat may cause damage to the housing and other parts 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 9 e Do not install this display in areas where extreme vibrations may be generated For example nearby manufacturing equipment may produce strong vibrations The vibrations may cause the display to exhibit picture discoloration or poor video quality e Ensure the metal enclosure does not contact the touch sensor e Be sure to gasket the display to its enclosure properly to prevent damage to the touch sensor e To avoid ergonomic concerns Do not install the display in a manner or location with awkward accessibility Extended use may result in muscle tendon or fixed posture strains It is recommended you take periodic breaks from continuous use Service and Repair Indicators Do not attempt to service this unit yourself Removing the display cover may expose you to dangerous voltages or other risks Unplug the display from the power outlet and refer servicing to qualified service personnel in the event that e Liquid is spilled into the product or the product is exposed to rain or water e The product does not operate properly when the operating instructions are followed e The product has been dropped
8. Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 17 e Be sure to adjust the controls in your normal lighting conditions e Display a test image or pattern whenever you adjust the video Your Multi Touch Chassis Display has five controls for adjusting the video display O0 amp 8 amp 8 amp 8 MENU SELECT LED POWER Your Multi Touch Chassis Display has four controls to adjust the video display e Menu Shows or hides the on screen display menu e Select Highlights the current menu option and enables you to scroll forward through items on the menus e plus sign Press to move from the Menu selection to specific choices and to increase the value of a selected option e minus sign Press to decrease the value of selected option If you do not press any buttons the display adjustment program times out you can adjust this time up to 12 seconds and hides the menu options You can press the Menu button at any time to display the options again Pressing Menu will pull up the On Screen Display OSD menus as shown below Image Menu Display Menu System Menu 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide OSD Choices Image Menu Brightness Contrast Sharpness Color Temperature Choices are Brightness Contrast Sharpness or Color Brightness Selecting the Brightnes
9. The MCVs are by weight in homogeneous materials This information represents 3M s knowledge and belief which may be based in whole or in part on information provided by third party suppliers to 3M NOTICE Given the variety of factors that can affect the use and performance of a 3M Touch Systems Inc Product the Product including that solid state equipment has operation characteristics different from electromechanical equipment some of which factors are uniquely within User s knowledge and control it is essential that User evaluate the 3M Touch Systems Inc Product and software to determine whether it is suitable for User s particular purpose and suitable for User s method of application 3M Touch Systems Inc statements engineering technical information and recommendations are provided for User s convenience but their accuracy or completeness is not warranted 3M Touch Systems Inc products and software are not specifically designed for use in medical devices as defined by United States federal law 3M Touch Systems Inc products and software should not be used in such applications without 3M Touch Systems Inc express written consent User should contact its sales representative if User s opportunity involves a medical device application IMPORTANT NOTICE TO PURCHASER Specifications are subject to change without notice These 3M Touch Systems Inc Products and software are warranted to meet their published specifications f
10. ch functionality for next generation multi touch applications This display provides full multi touch functionality including traditional pinch expand and rotate features Each touch is independently recognized thereby supporting full multi touch and multi user input 3M Touch Systems Inc Proprietary Information TSD 37732F 6 3M Multi Touch Chassis Display User Guide The Multi Touch Chassis Display uses projected capacitive technology with an all glass front surface and provides multi touch functionality in a highly durable form factor The fast response rate enables the creation of multi touch applications and supports real time rendering of maps and other speed sensitive applications The display also features space saving designs high resolution and low power consumption These qualities make the Multi Touch Chassis Display ideal for applications that require superior color resolution and clarity Important Safety Information Read and understand all safety information before using this product Follow all instructions marked on the product and described in this document Pay close attention to the following installation warnings and safety precautions Intended Use The 3M Touch Systems Multi Touch Chassis Display was designed for touch input and tested to replace an existing display These displays are intended for indoor use only and are not designed for use in hazardous locations Explanation of Signal Word Conseque
11. d Video Display Modes and Refresh Rates Your video card should support one of the display modes specified in Table 1 If you select an unsupported video mode the display may stop working or display unsatisfactory picture quality Table 1 Applicable Display Mode and Refresh Rate Display Mode Refresh Rate Hz 640 x 480 60 67 72 and 75 720 x 400 70 800 x 600 56 60 72 and 75 832 x 624 73 960 x 600 59 6 1024 x 768 60 70 72 and 75 1152 x 720 59 9 1280 x 800 59 8 1280 x 1024 60 and 75 1680 x 1050 59 9 Configuring the Display Settings After you connect your Multi Touch Chassis Display and turn on your computer you may need to configure one or more of these display settings The ideal setting for the Multi Touch Chassis Display is as follows e Display mode also called desktop area or video native resolution 1680 x 1050 e Refresh rate also called vertical scan rate or vertical sync 60 Hz e Color depth also called color palette or number of colors at least 16 bit high color Adjusting the Multi Touch Chassis Video Display This section provides guidelines for adjusting the video display and using the display controls to adjust the image to your liking The controls for adjusting the video display are located on the back of the Multi Touch Chassis Display These buttons let you display the on screen menu and adjust the phase image position contrast and brightness Before you make any adjustments 3M Touch Systems
12. e grounded power source Do not use a power cord that is frayed or otherwise damaged To avoid the risk of electric shock which may result in serious injury or death Do not service the display yourself There are no user serviceable parts inside Refer all servicing to qualified service personnel Any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment Do not use non conforming replacement parts Do not place wet or damp objects on the display Do not expose the display to rain or other sources of water steam or moisture Do not place foreign objects on the display or its cables Do not remove the cover or back of the display Ensure that connecting the unit to the power source will not overload the power source A CAUTION To avoid the risk of potential damage to the display electronics Always use the VESA mounting holes when using an arm attachment Do not drill additional holes in the unit to mount plates other locations Do not use longer screws as they could potentially damage electronics inside the display To avoid the risk of glass breakage which may result in minor or moderate injury To avoid risk of injury the when handling the display be aware that the sensor edges are very sharp Handle the display with care to avoid breaking the touch sensor The display contains glass parts Dropping the display may cause t
13. eee enone eee eens 13 Testing the Multi Touch Chassis Display 22 2 casacsasendeacacnaadceadensaccacnascdeaceeseedeaaee 13 Mounting the Multi Touch Chassis Display 000c0cccccceeceeeeeeeeeeeeeeeeeeeeeeeeeees 14 Articulating Arm Mounting Option 2222 150015220 c22204 esaagaassenscansaatagagnecssasaiecseaaaneeviaseeee 14 Access to the Video Controls earren nanan Anaa a ANAA ATAARE AREARE AAAA ARANEA 15 Clearance and VY Cm AO ssania TAE EE 15 Video Card Requirements ersssrerssrrisnersired unuas ananena uneeachessunceieu kanes venseaseeveceuanesacsac 15 Using the Standard Controls for the Video Card 2 212 25222220sssacaseseesassaaiceseseeaceeaezanes 15 Supported Video Display Modes and Refresh Rates ccccccccccccccccceeeeeeeeeeeeeees 16 Configuring the Display Settings esc stccc5 cissceccostcnsscesncduancesancnssdasadeusesssces edeaceaucasceeiee 16 Adjusting the Multi Touch Chassis Video Display cccccccccccceseeeeeeeeeeeeeeees 16 Enabling Your Multi Touch Chassis Display Windows UTS BC Oe ON tt tree cece EA E eae eve 2 PAM CAS E O e E A R EA A E E 23 Multi Touch Application SIN ON gcse esceaseeetyveeeecuiseinssbesxce Gaiiecstanasdeiarsicsedinenldeasd 23 Installing 3M MicroTouch SOM Ware 25 casecneayaveaivestdtethaleeiatierediedearetealetasesielvels 24 VICO Pa A A Nt esp ct aa tdi pd pate eesti hem eerste E EAEN 24 3M Touch Systems Inc Proprietary Information TSD 37732F Appendix A Appendix B
14. ent power cable Try using a different electrical outlet No image displayed blank Is the display receiving a valid video signal from the PC screen Check that the computer is powered on Check that the video cable is connected properly and securely to the display and the computer Check that the LED on the rear of the unit is green Check that no pins are bent in the video cable connector Check that the video card 1s firmly seated in the card slot in your computer 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 27 Issue No image displayed blank screen No image displayed blank screen Abnormal image Colors of image are abnormal Disturbances on the screen Solution e Check that the video input from the video card falls within the refresh rate of the display Refer to Table 1 for details e Check that your computer is using a supported display mode Refer to Table 1 for details Is the display in Power Management mode e Ifthe LED on the rear of the display is flashing amber touch the screen press any key on the keyboard or move the mouse to restore operation Are the brightness and contrast settings too low e Use the display controls to adjust these values e Check that the video input from the video card falls within the refresh rate of the display Refer to Table 1 for details e Check that the video cable is connected properly
15. essory kit includes four brackets and 8 screws The mounting holes are located on all 4 sides of the display Always use the supplied screws M4 x 8 mm Caution Always use the mounting holes when attaching to the brackets Do not drill additional holes in the unit to mount brackets to other locations You can attach the brackets to the edges of the chassis The brackets are slotted allowing the chassis to slide in and out You can also rotate the brackets to various positions Note ESD susceptibility at the system level is dependent on the integration methodology To ensure proper ESD protection for the chassis display in ESD sensitive applications 3M Touch Systems recommends that the perimeter of the display be surrounded by an electrically insulating closed cell foam gasket Given the variety of factors that can affect the use and performance of any product some of which are uniquely within the user s knowledge and control it is essential that the user evaluate the specific gasket to determine whether it is suitable for a particular purpose and suitable for the user s intended application Articulating Arm Mounting Option The unit has a 100 mm VESA mounting pattern on the back to allow for arm mount capability Use M4 x 7 mm screws to secure the VESA mount stand for use only with UL listed wall mount bracket with minimum weight load capability of 20 28 Ibs 9 2 kg Follow the manufacturer s instructions included with the mountin
16. following tasks e Unpack the components e Connect the video touch display cables and power cable e Power on the display and test your setup e If you are not running Windows 7 or Tablet PC install MT7 software from the enclosed CD Note that this will not make multi touch happen it is up to your application to enable multi touch System Requirements The Multi Touch Chassis Display requires a personal computer PC The requirements for your PC are as follows e Your PC must have an available USB or RS 232 serial communication COM port You connect the touch sensor cable to this communications port e Your PC must have a video card and video driver already installed for the display If you need to install a video card or a video driver refer to your computer documentation for instructions Note Before setting up your Multi Touch Chassis Display refer to the Important Safety Information section at the beginning of this document Unpacking Your Touch Display Carefully unpack the carton and inspect the contents Your Multi Touch Chassis Display includes the following cables and accessories e USB and RS 232 serial communication cables e DVI and VGA video cables 3M Touch Systems Inc Proprietary Information TSD 37732F 12 3M Multi Touch Chassis Display User Guide e Power brick 90 264VAC and 47 63 Hz input e LITEON PA 1081 01 or EDAC EA11001C 120 for the C2254PW e LITEON PA 1041 0 or EDAC EA10521E 120
17. for the C2234PW e US UK or EU power cables as needed e Hardware Kit 4 Mounting brackets 2 top and 2 side mount options 8 screws e Software CD and documentation Cables Included with Your Chassis Multi Touch Display USB Cable US power cable VGA cable DVI cable 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 13 Connecting the Touch Display CAUTION You are cautioned that any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment To connect the Multi Touch Chassis Display 1 Turn off your computer You should always turn off the computer before connecting or disconnecting a device 2 Select either the DVI or VGA cable Connect one end of the video cable to the video connector on the display Connect the other end to the video card in your computer 3 Connect one end of the touch sensor cable either USB or serial to the LCD Connect the other end to an available port on your computer Note Do not connect both USB and serial cables to the display Choose one or the other Plug the power brick into the display Connect the power cable to an appropriate grounded power source Testing the Multi Touch Chassis Display Note The Multi Touch Chassis Display has a power status light and video controls located on the back of the dis
18. g device to properly attach your display Caution e Do not use longer screws as they could potentially damage electronics inside the display e Always use the VESA mounting holes when using an arm attachment Do not drill additional holes in the unit to mount plates in other locations 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 15 Access to the Video Controls The Multi Touch Chassis Display has five buttons for using the on screen menu and adjusting the video display These controls are located on the back of the Multi Touch Chassis Display These buttons let you display the on screen menu and adjust the phase image position contrast and brightness Make sure you will be able to access the video controls once the Multi Touch Chassis Display is installed If enclosure space is tight and access is important an on screen display remote control part number 30114 is an option Clearance and Ventilation Leave at least two inches of clearance space behind the Multi Touch Chassis Display for proper ventilation Units have vent holes at the top and bottom on the back of the chassis ensure these holes are not blocked during installation Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation Refer to the published specifications for the maximum and minimum operating temperature and humidity cond
19. he glass parts to break Ensure mounting screws are tightened fully to prevent instability Do not place foreign objects on the display Ensure that mounting the unit will not adversely affect the stability of the end equipment when installing in free standing equipment or using the VESA mount 3M Touch Systems Inc Proprietary Information TSD 37732F 8 3M Multi Touch Chassis Display User Guide A CAUTION To avoid the potentially hazardous situations associated with the use of alcohol or other solvents which may result in minor or moderate injury or property damage e Follow all instructions and recommendations in the manufacturer s Material Safety Data Sheet and product label Be sure to follow solvent manufacturer s precautions and directions for use when using any solvents It is important to avoid using any caustic chemicals on the touch sensor To avoid possible environmental contamination which may result in minor or moderate injury e The lamp s inside this product contain mercury Hg and must be recycled or disposed of in accordance with local state or federal laws Check your individual state s requirements to see if specific recycling requirements exist for mercury containing products or other electronic products Refer to http www nema org lamprecycle or call 3M Touch Systems 1 866 407 6666 for further information e Dispose of the flat panel display according to applicable governmental regulations
20. ide 21 OSD Choices OSD H Position OSD V Position Languages OSD H Position Adjusts the horizontal placement of the OSD display on your screen Settings are saved automatically OSD V Position Adjusts the vertical placement of the OSD display on your screen Settings are saved automatically Transparency Adjusts the transparency of the OSD screen on your display Settings are saved automatically Language Sets the language for the OSD the choices are English French German Spanish and Chinese Settings are saved automatically 3M Touch Systems Inc Proprietary Information TSD 37732F 22 3M Multi Touch Chassis Display User Guide OSD Choices Reset Resets the control functions back to the original factory preset values Reset Defaults Settings are saved automatically 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 23 CHAPTER 3 Enabling Your Multi Touch Chassis Display Windows 7 USB Compatibility 3M multi touch technology works seamlessly with the Windows 7 operating system The Multi Touch display supports USB HID for direct communication The Multi Touch Chassis Display leverages all the multi touch functionality that is native to Windows 7 Plug the display in to a system running Windows 7 and you ll quickly enter the world of true multi touch functionality The Multi Touch Chassis Display is compatible with Wind
21. itions Refer to the product data sheet on the 3M Touch Systems website at http www 3m com touch Video Card Requirements Before you connect your touch display make sure your computer has a video card installed that supports the native video resolution of 1680 x 1050 for the Multi Touch Chassis Display If you need information on installing a video card or video driver refer to the manual that came with your video card Using the Standard Controls for the Video Card In addition to the standard controls on the display each video card has several controls that let you adjust the display settings The software and driver for each video card is unique In most cases you adjust these settings by using a program or utility provided by the manufacturer of the video card 3M Touch Systems Inc Proprietary Information TSD 37732F 16 3M Multi Touch Chassis Display User Guide For example you can use the Windows Display Properties control panel to adjust the desktop area resolution color depth and refresh rate Whenever you change these settings the image size position or shape may change This behavior is normal You can readjust the image using the display controls described in this chapter For more information on adjusting the desktop area resolution color depth or refresh rate refer to the user manual that came with your video card If you change the resolution it is a good idea to calibrate your touch screen Supporte
22. itle 3M Multi Touch Chassis Display User Guide Document Number TSD 37732 Version F 3M the 3M logo MicroTouch and the MicroTouch logo are either registered trademarks or trademarks of 3M in the United States and or other countries Windows and or other Microsoft products referenced herein are either registered trademarks or trademarks of Microsoft Corporation in the U S and or other countries Linux is a registered trademark of Linus Torvalds in the U S and or other countries All other trademarks are the property of their respective owners 3M Touch Systems Inc Proprietary Information TSD 37732F Chapter 1 Chapter 2 Chapter 3 3M Multi Touch Chassis Display User Guide Contents Introduction Oy oreo a teeta ves eeepc ss iene sac eyssaeeaeadicie te aia aon es seas 5 laporont oal ciy OOA Oesen Net anne mene ne E TNE ts ttt tener Settee fase rt Sem 6 WA OTA OTS 8 aera taasent eee E antwcetaetsacaatea binant earstauenteciss EE 8 Service and Repair Indicators sruse een ecictesnedecleeanbaetuestpcveleeniniateaxtenedecasesbexeameauneeaeee 9 Touch Sensor Care and C leani urucen a A 9 3M Touch Systems Support Services ssesiriissictsnseris ne NEEE a T 10 Contacto M Touch SysteNS eee ee ene ee ne meee 10 Setting up Your Multi Touch Chassis Display Syse Reem NiS en ee ne ne ee een 11 Unpacking Your Touch Display sac sc2ccnsecsaeececaasenaseatacaceassaaaaseaaacaassonsasaiesaagansanseaenens 11 Connecting th Touch Display eae eee
23. leur du Canada This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Warning To assure continued FCC compliance the user must use the supplied grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores Also any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 3M Touch Systems is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment CE Conformity for Europe The device complies with the requirements of the ECC directive 2004 108 EC with regard to Electromagnetic compatibility and 2006 95 EC with regard to Safety 3M Touch Systems Inc Proprietary Information TSD 37732F
24. nces A DANGER Indicates a potentially hazardous situation which if not avoided will result in death or serious injury and or property damage A WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and or property damage A CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury and or property damage CAUTION Indicates a potentially hazardous situation which if not avoided may result in property damage A DANGER To avoid the risk of fire and or explosion which will result in serious injury or death e Do not install or use this product in a hazardous location A WARNING To avoid the risk of fire which could result in serious injury or death e Do not remove the cover or back of the display dangerous voltages inside 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide A WARNING To avoid the risk of electric shock which could result in serious injury or death Do not remove the cover or back of the display The backlight inverter output is at high voltage This device must be operated with the original power supply and cable provided as shown below e LITEON PA 1081 01 or EDAC EA11001C 120 for the C2254PW e LITEON PA 1041 0 or EDAC EA10521E 120 for the C2234PW Do not use a damaged power supply Plug power cord into appropriat
25. ng your touch sensor preferences and a diagnostic utility If you are experiencing problems with the touch sensor you can use the diagnostic utilities provided to test the system For more information on installing this software and using the control panel refer to the 3M MicroTouch Software User Guide on the accompanying CD or on the corporate website at www 3m com touch Video Alignment The Multi Touch Chassis has been calibrated prior to shipment and the display as delivered does not require video alignment You should be able to accurately touch icons on the sensor If for some reason you cannot do this the touch sensor s active area may not be aligned to the underlying video Regardless of the operating system after you connect your touch display If you are using Windows 7 you may calibrate by accessing the Software Diagnostic Utility SDU found on the enclosed CD Launch the SDU from the CD Select the Tools menu and highlight Calibration The screen below appears and you should touch the 2 targets as they appear Press Escape to cancel Calibration CO 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 25 Ifyou are using 3M MicroTouch MT 7 Software launch the MT 7 Control Panel and follow the instructions on the Main tab You ll be asked to touch 3 targets F W MT 7 Software Control Panel Version 7 13 r Calibration MT 7 provides a 3
26. or the metal case has been damaged e The product exhibits a distinct change in performance indicating a need for service e The power cable or plug is damaged or frayed Touch Sensor Care and Cleaning The touch sensor requires very little maintenance 3M Touch Systems recommends that you periodically clean the glass touch sensor surface Be sure to turn off your display before cleaning Typically an isopropyl alcohol and water solution ratio of 50 50 is the best cleaning agent for your touch sensor You can also use straight isopropyl alcohol CAUTION To avoid the potentially hazardous situations associated with the use of alcohol or other solvents which may result in minor or moderate injury or property damage e Follow all instructions and recommendations in the manufacturer s Material Safety Data Sheet and product label Be sure to follow solvent manufacturer s precautions and directions for use when using any solvents It is important to avoid using any caustic chemicals on the touch sensor e Apply the cleaner with a soft lint free cloth Avoid using gritty cloths 3M Touch Systems Inc Proprietary Information TSD 37732F 10 3M Multi Touch Chassis Display User Guide e Always dampen the cloth and then clean the sensor Be sure to spray the cleaning liquid onto the cloth not the sensor so that drips do not seep inside the display or stain the bezel 3M Touch Systems Support Services 3M Touch Systems
27. ows 7 with no additional software Refer to Microsoft s Windows 7 documentation for additional information All Other Platforms When using a Windows 7 serial connection or for Windows XP Vista or Linux operating systems either USB or serial 3M provides MicroTouch MT 7 Software for multi touch drivers This guide includes information for writing your own drivers to interface with the 3M Multi Touch Technology For non Windows 7 operating system users this document provides the communication protocol necessary to talk directly with the electronics This enables software developers using other operating systems such as Microsoft Windows Vista or Linux to write their own drivers and achieve the same multi touch results Multi Touch Application Support Remember not all applications are multi touch ready Multi touch behavior is a function of YOUR application Check with your application vendor to determine if your software has multi touch capability 3M Touch Systems Inc Proprietary Information TSD 37732F 24 3M Multi Touch Chassis Display User Guide Installing 3M MicroTouch Software Remember that Windows 7 does not require any additional software to enable multi touch functionality However for Windows XP Vista or Linux operating systems 3M MicroTouch Software enables your Multi Touch Chassis Display to work with your computer 3M MicroTouch Software includes a control panel for setti
28. play If enclosure space is tight and access is important an on screen display remote control part number 30114 is an option Before testing your touch display make sure all cables are connected properly Be sure to tighten all cable screws After connection turn on the power switch located on the back of the display To test that the display is working properly Turn on your computer 2 Make sure the video image is displayed If it is not check the LED to ensure that the display is not in power save mode amber 3 Make sure the video image is centered within the screen area Use the display controls to adjust the image if necessary You can adjust the horizontal and vertical position contrast and brightness to better suit your video card and your personal preference For additional details refer to the Adjusting the Video Display later in this chapter 3M Touch Systems Inc Proprietary Information TSD 37732F 14 3M Multi Touch Chassis Display User Guide Mounting the Multi Touch Chassis Display The Multi Touch Chassis Display is designed to fit any type of enclosure All 3M Touch Systems chassis displays are encased in rugged metal instead of plastic making them easy to integrate Caution To avoid the risk of injury when handling the display be aware that the sensor edges are very sharp The Multi Touch Chassis Display includes a hardware accessory kit for mounting the unit into an enclosure The hardware acc
29. rom the date of shipment and for the period stated in the specification 3M Touch Systems Inc makes no additional warranties express or implied including but not limited to any implied warranties of merchantability or fitness for a particular purpose User is responsible for determining whether the 3M Touch Systems Inc Products and software are fit for User s particular purpose and suitable for its method of production including intellectual property liability for User s application If the Product software or software media is proven not to have met 3M Touch Systems Inc warranty then 3M Touch Systems Inc sole obligation and User s and Purchaser s exclusive remedy will be at 3M Touch Systems Inc option to repair or replace that Product quantity or software media or to refund its purchase price 3M Touch Systems Inc has no obligation under 3M Touch Systems Inc warranty for any Product software or software media that has been modified or damaged through misuse accident neglect or subsequent manufacturing operations or assemblies by anyone other than 3M Touch Systems Inc 3M Touch Systems Inc shall not be liable in any action against it in any way related to the Products or software for any loss or damages whether non specified direct indirect special incidental or consequential including downtime loss of profits or goodwill regardless of the legal theory asserted Copyright 2010 12 3M All rights reserved Document T
30. s B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Move the equipment away from the receiver e Consult the dealer or an experienced radio television technician for additional suggestions CAUTION You are cautioned that any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment 3M Touch Systems Inc Proprietary Information TSD 37732F 30 3M Multi Touch Chassis Display User Guide This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du Reglement sur le mat riel brouil
31. s option will allow you to adjust the luminescence of the display Adjust the brightness using the up and down buttons Settings are saved automatically Contrast Selecting the Contrast option increases or decreases the strength lightness or dimness of the image Adjust the contrast using the up and down buttons Settings are saved automatically Sharpness Adjusts the video quality to be sharp or blurry special for text mode Settings are saved automatically Color Submenu Choices are Preset Color Temp or User Settings Color Temperature Menu Adjusts color temperature to presets 6500k 7500k 9300k or to User defined color settings Settings are saved automatically Color Temperature Presets Adjusts color temperature to presets 6500k 7500k 9300k or User defined color settings Settings are saved automatically 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 19 OSD Choices Auto Adjust H Position User Settings Adjust the Red Green and Blue channels to your preference Settings are saved automatically Choices are Auto Adjust Clock Phase H Position V Position Not available when using the DVI connection Auto Adjust Performs automatic configuration of the Clock Phase Vertical and Horizontal positions If you do an Auto Tune the display will try to find the best setting If you are not satisfied with the auto adjustment fine tune the se
32. tional information Cursor is not located directly e Open the touch sensor control panel and make sure all cursor offsets underneath your finger vertical edge horizontal are turned off e Calibrate the touch sensor for the current video resolution and operating system Power Management The Multi Touch Chassis Display conforms to the Video Electronics Standards Association VESA Display Power Management Signaling DPMS standard To benefit from power management the display must be used in conjunction with a computer and video card that implements the VESA DPMS standard The PC automatically invokes the power management feature if you do not use the touch sensor mouse or keyboard for a user defined period To restore the video image simply touch the sensor press a key or move the mouse To set the period of time after which the PC will invoke the power management feature refer to the user manual that came with your video card or PC The touch sensor will remain on throughout this sequence 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Guide 29 APPENDIX B Regulatory Information Regulatory Agency Approvals Your product complies with the following regulatory standards e FCC B e CE e UL60950 IEC60950 EN60950 certified in compliance with the CB test scheme e RoHS WEEE directives e CCC This equipment has been tested and found to comply within limits for a Clas
33. ttings manually as described below Settings are saved automatically Clock If the clock setting is not fine tuned you may observe periodic vertical bars of video noise on your image These bars of noise are usually adjusted out when an Auto Adjust is performed If the bars of noise are still present this setting can be adjusted manually Settings are saved automatically Phase Adjust this setting so that either the vertical bars of noise are replaced by an even amount of noise across the whole screen or the noise disappears completely Settings are saved automatically H Position Horizontal Position Moves image horizontally on screen either left or right Settings are saved automatically 3M Touch Systems Inc Proprietary Information TSD 37732F 20 3M Multi Touch Chassis Display User Guide OSD Choices V Position Vertical position Moves images vertically on screen either up or down Settings are x ically V Position saved automatically System Menu Choices include Input OSD Language and Reset Settings Input a Selects the applicable input source either VGA or DVI Settings are saved automatically OSD Settings Submenu Choices are OSD Timer OSD H Position OSD V Position and Transparency OSD Timer Adjust how long the menu remains on the screen Settings are saved automatically 3M Touch Systems Inc Proprietary Information TSD 37732F 3M Multi Touch Chassis Display User Gu
Download Pdf Manuals
Related Search