Home

NEC E424

1. Unplug the power cord from the outlet when the TV is not in use for long periods of time days Important Safety Instructions Read before operating equipment Follow all warnings and instructions marked on this TV 1 puo S qc e DU 10 11 12 13 14 15 16 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is use
2. 4 Insert the bottom of the battery the side into the battery compartment first push towards the springs and insert the top of the battery the side into place Do not force the battery into the battery compartment 5 Close the battery cover making sure the tabs rest in the corresponding holes and push down the cover until it clicks shut Connect To The Power Source The TV should be installed close to an easily accessible power outlet Fully insert the prongs into the power outlet socket A loose connection may cause image degradation If there is power to the TV the front LED at the bottom of the TV will be either none or red A red LED means the TV is in standby mode English 18 Power On Off Your New LCD TV Press the power button on the remote control or press the power button located on the side of the TV The TV will power on Power button t o lt o r O gt 0 Or O L TV AV f comp f Hompe C m Zz c C z TU c 4 v o m p lt N Power Mode Status Warming up mode can automatically turn the Monitor power on when signal appears Press the power button on remote control or on side keypad can power on the Monitor in standby mode English 19 Source Connection Guide E654 RS 232C IOIOI r COMPONENT AV IN BH o o o OUT Y AV Pb Cb Pr Cr L R ANT CABLE 2 RS 232C Input from external equ
3. User s Manual E654 E554 E464 E424 E324 Index Precautions And Reminders iaescen cux orit enint tar Ond xx cda bad rs tAE tutae Sti ncaseacsn English 1 Important Safety INStrUCTIONS cccccseceecseseeeeceeseeeecesseeeceesseeesseaes English 2 Important gie lners iiio aT T English 5 Declaration Of Confofrilly caesos nates octo iesu b axdingu passo eR ete ea dx English 11 OMG EE EE EE English 13 mii circo P OE English 14 Attaching the BSSB icis aiiaioss ridic rca o REM EReF cH EDU bord pA MESA MEUS English 14 Using Cable Clamper ccccsssccccssseecceeeeceesseeseeesseseeeeseeees English 15 Preparing Your LCD TV For Wall Mounting optional English 15 Prohibit Portrait Condition LSe uer etra ren veneto ceu English 16 Place The TV On A Solid Surface sss English 17 Antenna Connection ccccccssesceccceeseccceeeeeeceseeesseseeeesaaees English 17 Battery Installation and Replacement English 18 Connect To The Power Source ccc csececsssseeeeceesseesseeeees English 18 Power On Off Your New LCD TV seseeeeeem English 19 Power Mode Status ccccccssseeecccsseecceeeceesceuseeessegeesessaees English 19 Source Connection Guide cce ontario xn Eo ront agar neue English 20 Operating Instructions iaceo essc entra aces 2I Io Spe DR dentes n Ue nba REO qp PADEidS English 24 Using The
4. antenna discharge unit size of grounding connectors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode 20 Rest your eyes periodically by focusing on an object at least 5 feet away Blink often 21 Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire 22 Do not use monitor in high temperature humid dusty or oily areas 23 Do not bend crimp or otherwise damage the power cord 24 Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus NOTE To the TV system installer This reminder is provided to call attention to Article 820 44 of the National Electric Code that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the facility as reasonably close to the point of cable entry as possible Antenna lead in wire NEC National Electric Code B v d Antenna discharge unit NEC Section 810 20 Ground clamp T Grounding conductors NEC Section 810 21 Electric service equipment Power service grounding electrode system NEC Art 250 Part H Ground clamps English 3 WARNING To prevent the apread of fire keep candles or other open flames away fram this product at all times IMPORTANT INFORMATION If a television is not positioned in
5. jacks SPDIF OUT Use a digital audio cable to connect stereo home theater system English 21 E464 E424 E324 ri DO DM E324 E464 E424 ANT CABLE SPDIF OUT r PCI 3 r COMPONENT AVIN a 00 VGA AUDIO Y AV Pb Cb Pr Cr E R RS 232C Input from external equipment such as a PC or AV control system in order to control RS 232C functions USB port Used for accessing JPEG photo files HDMI HDMM HDMI2 HDMI3 Connect your HDMI devices ANT CABLE Connect an RF antenna or Analog Cable system SPDIF OUT Use a digital audio cable to connectstereo home theater system COMPONENT AV IN Component Connect digital video equipment to the Video Green Y Blue Pb Red Pr jacks and matching Audio White L and Red R jacks Composite Connect digital video equipment to the Video Green AV jacks and matching Audio White L and Red R jacks PC IN VGA AUDIO Connect your PC video and audio English 22 Once your AV device is connected press the Source button on the remote control to select the relevant source to view ex Press COMP button to select Component if you have connected a source to the Component input English 23 Operating Instructions Using The Side Panel Controls 4 VOL Press to increase the volume Press this button to shift Right in the OSD menu gt VOL Press to decrease the volume Press this button to
6. 41 30 45 30 41 02 30 30 36 30 30 30 31 31 03 72 Od Select HDMI Input Source Select 01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 43 03 01 Od Component Input Source 54 30 41 30 45 30 41 02 30 30 36 30 30 30 30 35 03 77 Od Select Composite Sound Mute ON 01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 31 03 09 Od Sound Mute OFF 01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 32 03 0a Od English 41 Before Calling Service Please make these simple checks before calling service These tips may save you time and money as charges for receiver installation and adjustments of customer controls are not covered under your warranty Symptoms Items To Check And Actions To Follow Ghost or double image when using the tuner This may be caused by an obstruction to the antenna due to high rise buildings or hills Using a highly directional antenna may improve the picture No power Check to see if the TV s AC power cord is plugged into the outlet Unplug the TV and after 60 seconds reinsert the plug into the outlet and power on the TV No picture At the rear of the TV make sure the antenna connection is properly attached Check to see if there is a station broadcast problem by trying multiple channels Adjust the contrast and brightness settings Check the Closed Caption settings as some text modes may block the visibility of the images on the TM Good picture but no sound Increase the volume e Con
7. 42 Ee SAY MM T E English 43 Limited Waranty RE mo inei English 44 Rorer Ss eein a a a English 46 www necdisplaysolutions com Precautions And Reminders Do not place the TV in confined spaces or in a box when in use Maintain ample ventilation for the TV when in use Keep the TV away from direct sunlight dust humidity and smoke Unplug the AC cord from the AC outlet before cleaning Do not use liquid cleaners or aerosol cleaners to clean the TV Place the unit on a sturdy even surface Do not open the TV cabinet Unplug immediately if the TV falls Do not place the TV near water such as a bathtub Unplug immediately if the TV has been exposed to rain or water Do not insert any foreign objects into the TV cabinet Unplug immediately if objects have fallen into the monitor PP 996 AN j in English 1 Call a NEC certified service personnel for any internal service needed for Unplug immediately if there is a TV malfunction such as a loss of audio Do not cover or block any vents or openings Inadequate ventilation may shorten the life of the TV and cause overheating
8. QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems CAUTION Please use the power cord provided with this TV in accordance with the table below If a power cord is not supplied with this equipment please contact your supplier Plug Type Plug Shape Voltage North America U S A Canada AC 120 V English 5 Power source This LCD TV operates on 120 volts 60 Hz AC current Insert the power cord into a 120 volts 60 Hz outlet The mains plug is used as the disconnect device and shall remain readily operable To prevent electric shock from the TV do not use with an extension cord receptacle or other outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure Never connect the LCD TV to 50 Hz direct current or anything other than the specified voltage CAUTION Never remove the back cover of the LCD TV as this can expose you to very high voltages and other hazards If the TV does not operate properly unplug the LCD TV and call your authorized dealer or service center Adjust only those controls that are covered in the
9. Side Panel Controls eseeeeesssessss English 24 Using The Remote Control nanus English 25 Operating Range for the Remote Control English 26 TANO TANG Tm T E English 27 Navigating The On Screen Menu cccccseeeeeeceesseescesseeesseeeeeesees English 28 VIGGO MONU NT English 28 Audo Men RIITTNTNRER TERN C UTE English 29 Channels MON uero tru ae soot ens Exe EAE Fan TEE IRUA EO dU UE RER n EE Mee English 29 SOUDTVIEL os siccae uias uci eraT MUR A E E Mi cc EaEi DM RUE English 30 Photos Menu scan inctoianbidessimneninaosindedisantadiientnisniaansiandesaaamadabins English 31 Maintenance and Recycling ccccscccssseceseseceeseeeecseeeesseesensseensaes English 33 Care Of The Screen ERR UT English 33 Mobile Telephone Warning ssueiuesdasdakauasiwi cid Sia edid tu ater eic English 33 End Of Life Directives ccccsscccccsseeececeeseeesceseeesssseeeseaees English 33 Manufacturer s Recycling and Energy Information English 34 Disposing of your old NEC product seeeessssssss English 34 Energy SV cusesesseusmeeeaeceicesetenss deemed usines de inten eise iaaea English 34 mites oelorste ders o n NER TIT English 35 RS 232C Port Specifications eeeesseeeess English 41 Before Calling Service ccccccsssceccessseeceensececseseeseseueeeessageesessases English
10. instructions as improper changes or modifications not expressly approved by NEC could void the user s warranty Batteries installed warning CAUTION Incorrect usage of batteries can result in leaks or bursting NEC recommends the following battery use e Do not mix battery brands e Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type e Do not combine new and old batteries This can shorten the battery life or cause liquid leakage of the batteries e Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment e Do not touch exposed battery acid as it may injure skin e Remove the batteries if you do not intend to use the remote control for a long period of time e The batteries shall not be exposed to excessive heat such as sunshine fire or the like English 6 Image persistence Please be aware that LCD Technology may experience a phenomenon known as Image Persistence Image Persistence occurs when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be t
11. over panel native resolution size you cannot selet aspect X1 Press Menu button to return to the Folder Photo List View To control while in photo slideshow Press OK button to play or pause slideshow Press Menu button to stop the slideshow and return to photo browser Data Format for USB Photo Viewer JPEG IPG PE Max folder layer Max folder layer 9 Max number of 700 photos Max number of 200 favorite photos Min image 75 x 75 Ga resolution Max image resolution Progressive DCT Max image resolution Baseline Sequential DCT Supported file FAT32 system CAUTION e USB photo viewer only supports USB Mass storage class devices A JPEG image modified with PC may not be displayed Partly degraded files might be displayed at a reduced resolution Not guaranteed to support all USB devices e Do not use a USB Hub e Do not support multi partition USB NOTE e The folder and file names may be different depending on the digital camera used e Support USB 2 0 Type A connector DC5V max 500mA For USB device over 500mA we suggest to use adaptor or external power 1 iiid x 768 pixels 15 360 x 8 640 pixels English 32 Maintenance and Recycling Care Of The Screen Do not rub or strike the screen with anything hard as this may scratch mar or even damage the screen permanently Unplug the power cord before cleaning the screen Dust the TV by wiping
12. the screen and the cabinet with a soft clean cloth If the screen requires additional cleaning use a clean damp cloth Do not use liquid cleaners aerosol cleaners or solvents of any kind Mobile Telephone Warning Keep your mobile telephone away from your TV to avoid disturbances in the picture or sound possibly causing permanent damage to your TV End Of Life Directives In an effort to produce environmentally friendly products your new TV contains materials that can be recycled and reused At the end of your TV s life specialized companies can minimize display waste by separating the reusable materials from non reusable materials Please ensure you dispose of your TV according to local regulations English 33 Manufacturer s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company s top priorities in trying to minimize the burden placed on the environment We are engaged in developing environmentally friendly products and always strive to help define and comply with the latest independent standards from agencies such as ISO International Organisation for Standardization and TCO Swedish Trades Union Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re use upgrading reconditioning or reclamation of material Dedicated recycling sites ensure that environmentally harmful compon
13. x 768 60Hz 65 1280 x 720 60Hz o e T 74 25 1280 x 800 60Hz e e 83 5 e e Not e e WXGA FHD E324 E654 E554 E464 E424 Resolution Component HDMI Component 720p 60Hz 1080i 60Hz A 1080p 24Hz Not support Not support 1080p 30Hz Not support Not support NOTE A Use Down scaling function Image quality is limited English 27 Navigating The On Screen Menu Press the Menu button to display and Exit button to close the main menu Use the Navigation Ring to navigate select adjust or confirm an item on the OSD On Screen Display menu NOTE Some features may only be available in a particular source mode Video Menu Video Menu adjusts video items Picture Mode Energy Savings gt Brightness 50 Contrast co ENNEENB Color 55 SD Advanced Video Reset Video Settings l Ym vove o setect ew RETURN EXIT 1 Picture Mode Enter this menu to select from preset picture settings to optimize your TV s performance Dynamic Standard Energy Savings Theater Game Only for E654 E554 model Custom 2 Brightness Adjust picture brightness from 0 100 3 Contrast Adjust picture contrast from 0 100 4 Color Adjust picture color from 0 100 5 Advanced Video Select advanced video settings Dynamic Backlight DCR Enhance the contrasts between darkness and brightness to optimization the picture Color Temperature Se
14. 7 8 inches 4inches 4inches 10cm 10cm gt e Leave at least this space m around the set Neeson CORE 4 inches 2 36 inches i 6 cm For use only with UL Listed Wall Mount Bracket with minimum weight load Please refer to the Specification on page 36 and page 39 Unit without base weight The equipment and its associated mounting means still remain secure during the test Used wall mounting kit VESA compatible wall bracket distance diameter of Screw dimension Please refer to the Specification on page 36 and page 39 English 8 Installed with stand 11 7 8 inches 30 cm 4 inches 4 inches 10 cm 10 cm Leave at least this space around the set Z MEUS IE I a he ee I I I l 4 inches I 10 cm Never install the TV set where air circulation is blocked Objects and ventilation holes Never push objects of any kind into the TV through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or an electric shock Do not place any objects on the TV English 9 License Notice and Trademark Acknowledgement Windows is a registered trademark of Microsoft Corporation NEC is a registered trademark of NEC Corporation All other brands and product names are trademarks or registered trademarks of their respective owners Homi HIGH DEFINITION MULTIMEDIA INTERFACE LS ENERGY STAR DOLBY DIGITAL HDMI the
15. E324 Video Signal Cable User s Manual Mini D SUB 15 pin to Mini D SUB 15 pin m Only E324 s Stand Neck E654 M6 16mm 4 gt E554 E464 E424 M4 10mm Only E324 E554 E324 M4 8mm M4 12mm Stand Base Stand Screw x 4 Neck Screw x 4 NOTE 1 Remember to save your original box and packing material to transport or ship the monitor English 13 Preparation IMPORTANT Do not apply pressure to the TV screen display area which may compromise the integrity of the display The manufacturer s warranty does not cover user abuse or improper installations Attaching the Base E654 Stand Screw x 4 E654 M6 16mm E554 E464 E424 Stand Screw x 4 E554 E464 E424 M4 10mm E324 Neck Screw x 4 E324 M4 12mm Stand Screw x 4 E324 M4 8mm 1 Place the TV face down on a soft and flat surface to prevent scratching and damage 2 Carefully align the base to the stand and fasten the screws with a cross head screwdriver CAUTION The base of the stand is very heavy Install with care to avoid injury such as dropping the base onto one s foot English 14 Using Cable Clamper Tie the cables together using the cable clamper Preparing Your LCD TV For Wall Mounting optional We suggest that you keep your TV at least 2 36 inches 60 mm from the wall to prevent cable interference Before mounting your TV on the wall you need to remove the base
16. For your safety only mount with a UL listed wall mount bracket that supports the weight of the TV Please see page 36 and page 39 To attach a wall mount bracket to your TV E654 step 1 step 2 1 Loosen the screws at the bottom of the base and remove the base 2 Loosen the screws at the bottom of the stand to remove the stand 3 Secure the wall mount bracket to the back of your TV using four M6 SCrews screen size inches required pitch mm VESA Hole depth CAUTION If you skip the step 1 and loosen the screws for stand directly please be sure to hold the base tightly to avoid dropping the base English 15 E554 E464 E424 E324 VESA Hole Neck Screw 1 Loosen the screws on the back of the stand base and remove the base 2 Secure the wall mount bracket to the back of your TV using four M4 screws for 32 only or M6 screws for 42 46 55 only required pitch mm VESA Hole depth 400 x 400 4 x M6 24mm 400 x 400 4 x M6 21mm 100 x 100 4 x M4 22mm NOTE Wall mounting solution is not included with the unit and is sold separately Contact your NEC representative for details It is necessary to provide screw of appropriate length Wall mount bracket thickness VESA Hole depth Prohibit Portrait Condition Use gt CAUTION Do not rotate the diplay from landscape to portrait English 16 Place The TV On A Solid Surface Ensure that t
17. HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries Only for E554 E464 E424 E324 Please keep the factory default settings as shipped in which the product can meet ENERGY STAR requirements Manufactured under license from Dolby Labortories Dolby and the double D symbol are trademarks of Dolby Laboratories English 10 Declaration Of Conformity This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation U S Responsible Party NEC Display Solutions of America Inc Address 500 Park Boulevard Suite 1100 Itasca Illinois 60143 Tel No 630 467 3000 Type of Product LCD TV Equipment Classification Class B Peripheral Model E654 E424 E554 E324 E464 C We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules Canadian Department of Communications Compliance Statement DOC This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60065 03 English 11 FCC Information 1 Use
18. a sufficiently stable location it can be potentially hazardous due to falling Many injuries particularly to children can be avoided by taking simple precautions such as Using cabinets or stands recommended by the manufacturer of the television Only using furniture that can safely support the television Ensuring the television is not overhanging the edge of the supporting furniture Not placing the television on tall furniture for example cupboards or bookcases without anchoring both the furniture and the television to a suitable support Not standing the televisions on cloth or other materials placed between the television and supporting furniture Educating children about the dangers of climbing on furniture to reach the television or its controls English 4 Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO
19. ation must be determined by consumer and is not warranted by NEC DISPLAY SOLUTIONS For the name of your nearest authorized NEC Display Solutions of America Inc service facility contact NEC Display Solutions of America Inc at 1 800 632 4662 English 45 References NEC Monitor Customer Service amp Support Customer Service and Technical Support Parts and Accessories 800 632 4662 888 634 4662 Fax 800 695 3044 Warranty Information www necdisplay com Online Technical Support www necdisplay com Sales and Product Information Sales information Line 888 632 6487 Canadian Customers 866 771 0266 Ext 4037 Government Sales 800 284 6320 Government Sales email gov necdisplay com Electronic Channels http www necdisplay com Product Registration http www necdisplay com Drivers and Downloads http www necdisplay com English 46
20. ce for the TV s internal left and right speakers from L50 R50 3 Advanced Audio Select advanced audio settings Bass Enhance the low frequencies Treble Enhance the high frequencies Internal Speakers Select Off to turn off the internal speakers Digital Output Select optical output options RAW or PCM Only available for digital channels or HDMI input source Audio Source Select audio sources in analog channels Mono Stereo SAP Only available for analog channels Audio Language Select language options in digital channels Only available for digital channels 4 Reset Audio Settings Reset Audio settings to factory default settings Channels Menu Channel Menu allows you to set your signal source options According to various requirements in different source modes certain features could be hidden disabled on the menu Auto Channel Scan Signal Strength Add Skip Channels Channels Favorite Channels Channel Labels Audio Only Auto Aspect Ta MOVE SELECT RETURN Exir Engl 1 Auto Channel Scan Automatically search the available channels 2 Signal Strength Access signal strength meter to help you adjust your antenna installation to optimize signal reception Only available for digital channels 3 Add Skip Channels Manually add or skip channels to the channel list Favorite Channels Add channels to your favorite channel list 5 Channel Labels C
21. d use caution when moving the cart apparatus combination to avoid injury from tip over LNI Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Unplug immediately if the monitor faces above condition The TV complies with the recommended safety standards for stability Do not put excessive force on the front or top of the cabinet This could cause the product to tip over and cause damage and or personal injury If monitor or glass is broken do not come in contact with the liquid crystal and handle with care English 2 17 Follow instructions for wall shelf or ceiling mounting as recommended by the manufacturer 18 An outdoor antenna should not be located near overhead power lines or any electrical circuits 19 If an outside antenna is connected to the receiver confirm that the antenna system is grounded to protect against voltage surges and built up static charges Section 810 of the National Electric Code ANSI NFPA No 70 1984 provides information with respect to proper grounding for the mast and supporting structure grounding of the lead in wire to an
22. de sets the TV toa more energy consuming mode 9 Monitor ID Set the monitor ID number from 1 100 All or Group A J 10 Reset AV amp Setup Reset all Audio Video and Setup settings to factory default settings Photos Menu You could easily browse images from USB device io E MOVE ok SELECT RETURN If no USB device is detected TV will display the message Please Insert USB flash driver 1 Browse Photos Browse photos in the USB flash drive EXIT JEZNI 2 Favorite Photos Only display your favorite photos 3 View Slideshow View your photos in a slideshow manner gt A Settings Change the slidwshow settings Repeat Shuffle Speed Transition English 31 To control while in photo folder Press A V 4 gt button to browse the photo files Press OK button to open a folder or a photo file which will be viewed on the full screen Press Menu button to return to USB Main Menu Press FAV button to add a photo file to favorite list or delete from favorite list To control while in full screen photo show e Press gt button to go to the next image Press lt button to go to the previous image Press OK button to rotate the image clockwise Press Wide to zoom the image The zoom function will switch between the 4 styles by cycle and x1 x2 x4 Fill info bar will appear on the right down corner of screen If the image resolution size is
23. ents are properly handled and securely disposed To ensure the best recycling of our products NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way once it has reached the end of its life All required information concerning the disposal of the product and country specific information on recycling facilities can be found on our following websites http www nec display solutions com greencompany in Europe http www nec display com in Japan or http www necdisplay com in USA Energy Saving This TV features an advanced energy saving capability When a VESA Display Power Management Signalling DPMS Standard signal is sent to the TV the Energy Saving mode is activated The TV enters a single Energy Saving mode Approx 260 W E654 Approx 122 W E554 Approx 100 W E464 Approx 85W E424 Approx 55 W E324 Standby Mode Less than 0 5 W Red O On Mode with USB with Audio English 34 Product Specification This model complies with the specifications listed below Reorient or relocate the receiving display Designs and specifications are subject to change without notice This model may not be compatible with features and or specifications that may be added in the future EIE NENNEN NN S 31 83 KHz Analog input Horizontal 15 625 15 734KHz 31 83KHz EvoguERE HDMI input Ec 60 75 Hz Analog i
24. erence ferrite cores may be used when connecting this LCD TV to video equipment and maintain at least 400mm spacing to other peripheral device FCC warning Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user s authority to operate this equipment Cables Connections to this device must be made with shielded cables with metallic RF EMI connector hoods to maintain compliance with FCC Rules and Regulations Canadian notice CAN ICES 3 B NMB 3 B Standard Television Receiving Apparatus Appareil de r ception t l vision ordinaire Canada BETS 7 NTMR 7 If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio display Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 English 12 Contents Your new NEC monitor box should contain the following e Monitor 1 e TV Stand base 1 e Stand Screw 4 e Stand Neck 1 Only E324 e Neck Screw 4 Only E324 e Remote control 1 1 5 V AAA batteries 2 Power cord 1 e D sub cable 1 e User s manual 1 E654 Wireless Remote Control Power Cord and AAA Batteries E554 E464 E424
25. firm that the TV is not muted by pressing the Mute button on the remote control Good sound but poor color Adjust the contrast color and brightness settings Poor picture Poor picture quality may occur when an activated S VHS camera or camcorder is connected to your TV and another peripheral at the same time Switch off one of the peripherals Snowy picture and noise when using the tuner Check the antenna connection and signal Presence of a horizontal dotted line This may be caused by electrical interference e g hairdryer nearby neon lights etc Power cycle the equipment by turning off and then turning back on TV not responding via the remote control Determine if the batteries are working and replace batteries if necessary Clean the remote control sensor lens on the TV If necessary utilize the buttons located on the side of the TV Select the TV mode to ensure your remote control is set in the TV mode English 42 Glossary HDTV HDTV displays are technically defined as being capable of displaying a minimum of 720p or 1080i active scan lines HDMI Inputs High Definition Multimedia Interface Audio Video Inputs are located on the receiver These connectors are used for the input of audio and video signals Designed to receive higher picture resolution and offer sound connection options Menu An on screen listing of features shown on the TV screen is made available f
26. hall not have been subjected to displaying of fixed images for long periods of time resulting in image persistence afterimage effects accident misuse or abuse or operated contrary to the instructions contained in the User s Manual Any such conditions will void this warranty NEC DISPLAY SOLUTIONS SHALL NOT BE LIABLE FOR DIRECT INDIRECT INCIDENTAL CONSEQUENTIAL OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NEC DISPLAY SOLUTIONS PRODUCT OTHER THAN THE LIABILITY STATED ABOVE THESE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR WARRANTIES OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU English 44 This Product is warranted in accordance with the terms of this limited warranty Consumers are cautioned that Product performance is affected by system configuration software the application customer data and operator control of the system among other factors While NEC DISPLAY SOLUTIONS Products are considered to be compatible with many systems specific functional implementation by the customers of the Product may very Therefore suitability of a Product for a specific purpose or applic
27. he LCD TV is placed in a wx position to allow free flow of air UIS Do not cover the ventilation openings m on the back cover K Do not place the TV near any open X N flames Do not allow the TV to be placed in an SS environment where it can be exposed to heat direct sunlight or rain and water Do not expose the equipment to any liquid Antenna Connection XN Unless your LCD TV is connected to S a cable TV system or to a centralized antenna system a good outdoor color TV antenna is recommended for best CABLE television performance However if fA you are located in an exceptionally TE good signal area that is free from interference and multiple image ghosts an indoor antenna may be sufficient When using a 75 Ohm coaxial cable system connect the CATV coaxial cable to the AIR CABLE 75 Ohm terminal Or if you have an antenna connect the coaxial cable to the same AIR CABLE terminal c English 17 Battery Installation and Replacement The remote control is powered by two 1 5V AAA batteries To install or replace batteries 1 Open the battery cover of the remote control by pushing and pulling it in the direction of the arrow 2 Insert two new AAN size batteries for the remote control When replacing old batteries push them towards the springs and lift them out 3 Match the batteries to the and marks in the battery compartment
28. his warranty covers only NEC DISPLAY SOLUTIONS supplied components Service required as a result of third party components is not covered under this warranty In order to be covered under this warranty the Product must have been purchased in the U S A or Canada by the original purchaser This warranty only covers Product distribution in the U S A or Canada by NEC DISPLAY SOLUTIONS No warranty service is provided outside of the U S A or Canada Proof of Purchase will be required by NEC DISPLAY SOLUTIONS to substantiate date of purchase Such proof of purchase must be an original bill of sale or receipt containing name and address of seller purchaser and the serial number of the product It shall be your obligation and expense to have the Product shipped freight prepaid or delivered to the authorized reseller from whom it was purchased or other facility authorized by NEC DISPLAY SOLUTIONS to render the services provided hereunder in either the original package or a similar package affording an equal degree of protection All Products returned to NEC DISPLAY SOLUTIONS for service MUST have prior approval which may be obtained by calling 1 800 632 4662 The Product shall not have been previously altered repaired or serviced by anyone other than a service facility authorized by NEC DISPLAY SOLUTIONS to render such service The serial number of the product shall not have been altered or removed In order to be covered by this warranty the Product s
29. ipment such as a PC or AV control system in order to control RS 232C functions HDMI HDMI1 HDMI2 HDMI3 Connect your HDMI devices USB port Used for accessing JPEG photo files PC IN VGA AUDIO Connect your PC video and audio ANT CABLE Connect an RF antenna or Analog Cable system COMPONENT AV IN Component Connect digital video equipment to the Video Green Y Blue Pb Red Pr jacks and matching Audio White L and Red R jacks Composite Connect digital video equipment to the Video Green AV jacks and matching Audio White L and Red R jacks 7 SPDIF OUT Use a digital audio cable to connect stereo home theater system o 9r d 9 Iw English 20 E554 p XE uico RS 232C KOO r COMPONENT AV IN BH o o o 0 OUT Y AV Pb Cb Pr Cr L R ANT CABLE a RS 232C Input from external equipment such as a PC or AV control system in order to control RS 232C functions HDMI HDMM HDMI2 HDMI3 Connect your HDMI devices USB port Used for accessing JPEG photo files PC IN VGA AUDIO Connect your PC video and audio ANT CABLE Connect an RF antenna or Analog Cable system COMPONENT AV IN Component Connect digital video equipment to the Video Green Y Blue Pb Red Pr jacks and matching Audio White L and Red R jacks Composite Connect digital video equipment to the Video Green AV jacks and matching Audio White L and Red R
30. l have to enter the new password first then enter again the new password to confirm Make sure to keep your new password Region 5 Use Region 5 to block various types of movies and television programs based on ratings systems used in the USA that you feel may be inappropriate due to its content The Region 5 option will operate for Digital Channels ATSC only Reset Region 5 Clear the downloaded RRT5 rating information and restore to the factory default settings English 30 Closed Caption Adjust the Closed Caption settings Caption Display Analog Captions Digital Captions Digital Caption Options Sleep Timer Select how long the TV will take to automatically turn intself off Off 5 10 15 30 60 90 120 180 240 minutes Input Labels Create labels for the devices connected to your TV Only available for Non TV input source RGB Options Only available for VGA input and when there is VGA signal input Auto Adjust Automatically adjust the image settings such as position H Position Adjust horizontal position V Position Adjust vertical position Clock Set to the minimum level if noise occurs Phase Eliminate flicker and distortion Reset RGB Options Reset RGB options to factory default settings System Info Indicate the display information Energy Options Select the power saving modes Home mode is intended for home use and will save much energy Retail mo
31. lect a choice from Cool Normal or Warm Noise Reduction Set to reduce the video noise Tint Adjust the hue Red Green Blue of the picture from R50 G50 Sharpness Adjust object edges to optimize picture detail from O 100 Adaptive Contrast Set to automatically adjust the picture detail and brightness Aspect Ratio Adjust how the picture fills the screen Normal Zoom Wide Cinema Auto Overscan On Off Some video formats may require different scanning modes in order to best display the image On Image size is larger than what can be displayed The image edge will appear cropped Approximately 9596 of the image will be shown on the screen Off Image size stays within the display area The whole image is displayed on the screen NOTE When you use a computer with HDMI out please set OFF Motion 120Hz Only for E654 E554 model Eliminate motion blur with clear detail and smooth motion Backlight Set the backlight brightness from 0 50 Reset Video Settings Reset video settings to factory default settings English 28 Audio Menu Audio Menu provides an audio adjustment for user to modify the audio setting Sound Mode Standard gt Balance Advanced Audio gt Reset Audio Settings gt SELECT RETURN EXIT JEZNI 1 Sound Mode Select preset audio modes Standard Movie Music News Custom 2 Balance Adjust the audio balan
32. ng on video card used 21 83 KHz Analog input Horizontal 15 625 15 734KHz 31 83KHz HDMI input 60 75 Hz Analog input Vertical 24Hz 30Hz 50Hz 60Hz 75Hz HDMI input Pixel Clock 25 156 MHz VHF 2 through 13 UHF 14 through 69 Cable TV Mild band A 8 through A 1 A through 1 Super band J through W Hyper band AA through ZZ AAA BBB Ultra band 65 through 94 100 through 125 Frequency Channel Coverage CONNECTIONS Downward HDMI 2 3 Type A Connectors Analog RGB D sub15 pin PC IN AUDIO Stereo mini jack AV shared with RCA PIN Type component 1 0 V p p 75 ohm COMPONENT LY AV IN AUDIOL R RCA PIN Type 0 5Vrms Y Y 1 0 V p p Pb Cb Pr Cr Pb Cb Pr Cr 0 7V p p 75 ohm CONNECTIONS Side RS 232C 9 Pin D sub HDMI 1 Type A Connectors ANT CABLE VHF UHF SPDIF OUT PCM Fibre optic English 38 WEIGHT amp DIMENSION Dimensions w Stand and Base W x H x D inch EGO Weight w Stand and Base lbs WALL MOUNTING wa wall bracket 100 x 100 mm Power Consumption 100 W 85W Standby 0 5W AUDIO 16 ohm 16 ohm 16 ohm Analog Audio Stereo L R 0 5Vrms Air Pressure 795 1 060 mbar 79 5 106Kpa Radiation Solar Heat 700 W m 41 18 x 26 54 x 8 43 37 68 x 24 69 x 8 43 28 57 x 19 5 x 8 43 English 39 PACKAGE CONTENTS Monitor 1 TV Stand base 1 Stand Screw 4 Stand Neck 1 Only E324 Neck Screw 4 Only E324 Remote co
33. nput Vertical 24Hz 30Hz 50Hz 60Hz 75Hz HDMI input Pixel Clock 25 156 MHz Television System NTSC Standard ATSC Standard 8 VSB Clear QAM VHF 2 through 13 UHF 14 through 69 Channel Coverage Cable TV Mild band A 8 through A 1 A through 1 Super band J through W Hyper band AA through ZZ AAA BBB Ultra band 65 through 94 100 through 125 CONNECTIONS Downward SPDIF OUT PCM Fibre optic AV RCA PIN Type shared with 1 0 Vip p 75 ohm COMPONENT ssc ean RCA PIN Type Y Y 1 0 V p p Pb Cb Pr Cr Pb Cb Pr Cr 0 7V p p 75 ohm ANT CABLE VHF UHF Analog RGB D sub15 pin PC IN English 35 E T XN NN NN RS 232C 9 Pin D sub WEIGHT amp DIMENSION Reg n and Base 48 86 x 31 1 x 10 8 ipm and Base 48 86 x 28 94 x 2 47 VESA compatible wall bracket UE Wx H wR aan it pro English 36 ELI NNNM NENNEN NN Air Pressure 795 1 060 mbar 79 5 106Kpa PACKAGE CONTENTS 1 Monitor TV Stand base 1 Stand Screw 4 Remote control 1 1 5 V AAA batteries 2 Power cord 1 D sub cable 1 User s manual 1 All specifications weights and dimensions are subject to change without prior notice Please access www necdisplay com for detailed specifications and dimensions for custom installations Supplied Accessories NOTE TV Base stand Screw M6 x 16mm M4 x 10mm VESA Hole Depth M6 30mm M6 24mm English 37 DISPLAY Over 16 million colors dependi
34. ntrol 1 1 5 V AAA batteries 2 Power cord 1 D sub cable 1 User s manual 1 Supplied Accessories All specifications weights and dimensions are subject to change without prior notice Please access www necdisplay com for detailed specifications and dimensions for custom installations NOTE TV Base stand Screw M4 x 10mm M4 x 10mm VESA Hole Depth M6 19mm M6 21mm M4 22mm English 40 RS 232C Port Specifications PC control of the TV Attach an RS 232C cable cross type commercially available to the supplied RS 232C for the connections NOTE This operation system should be used by a person who is accustomed to using computers Communication procedure Send the control commands from the PC via the RS 232C connector The TV operates according to the received command and sends a response message to the PC Do not send multiple commands at the same time Wait until the PC receives the response before sending the next command Interface stop bit i This LCD TV uses RXD TXD and GND lines for RS 232C control The reverse type cable null modem cable not include should be used for RS 232C control Control command diagram Function Monitor ID 1 ous rate 01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d Power OFF 01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d Input Source 01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 31 03 73 Od Select VGA Input Source 01 30
35. or user adjustments MPAA Motion Picture Association of America Multichannel Television sound MTS The broadcasting standard which allows stereo sounds to be transmitted with the display picture RF Radio Frequency or modulated signal design used by the carrier for television broadcasts Second Audio Program SAP Another or additional audio channel provided for in the Multichannel Television Sound MTS broadcast standard A monaural soundtrack included within the recorded or video signal usually containing a second language translation for the displayed program Sleep Timer You can set a time period for which the TV will automatically turn off English 43 Limited Warranty NEC Display Solutions of America Inc hereinafter NEC DISPLAY SOLUTIONS warrants this Product to be free from defects in material and workmanship and subject to the conditions set forth below agrees to repair or replace at NEC DISPLAY SOLUTIONS sole option any part of the enclosed unit which proves defective for a period of three 3 years from the date of first consumer purchase Spare parts are warranted for ninety 90 days Replacement parts of unit may be new or refurbished and will meet specifications of the original parts or unit This warranty gives you specific legal rights and you may also have other rights which vary from state to state this warranty is limited to the original purchaser of the Product and is not transferable T
36. reate labels to any channel English 29 6 Audio Only Play the audio only when picture is turned off Any press of the button except the 5 Power button on the remote control will turn on the picture 7 Auto Aspect Automatically adjust the picture aspect ratio according to the TV program Setup Menu Setup Menu in TV mode is shown below According to various requirements in different source modes certain features could be hidden disabled on the menu Menu Language English gt Parental Controls Closed Caption Sleep Timer Input Labels RGB Options System Info ri Move SELECT RETURN EXIT NS Sleep Timer Input Labels RGB Options System Info Energy Options Monitor ID Reset AV amp Setup Ta Move SELECT RETURN i 1 Menu Language Select the menu display language English Frangais Espanol EXIT 2 Parental Controls Set TV parental controls This function blocks out the picture and sound of the selected rating levels The factory preset password to enter Parental Controls feature is a 4 digit number 0000 Panel Lock Lock or unlock all buttons on the TV s panel Block Unrated TV Block or unblock the unrated programs US Set the parental control level using Movie Rating memu or TV Rating memu Canadian Set the parental control level using Canadian English memu or Canadian French memu Change Password Change the 4 digit password You wil
37. shift Left in the OSD menu 3 CHA Press to change channels i Press this button to shift up in the OSD menu 4 CHv Press to change channels Press this button to shift down in the OSD menu MENU Press to open or exit the OSD On Screen Display menu INPUT Press to select the input source POWER Press to turn on off standby the TV English 24 Using The Remote Control 5 Power Press to turn On Off standby the power NOTE To completely turn off the power unplug the power cord from the power outlet TV IAL Press to choose ATSC NTSC tuner source mode 5 6 8 9 0 TV AV comp f Hompe AV Press to choose Composite source mode COMP Press to choose Component source Source mode HDMI PC Press repeatedly to choose PC IN or HDMI source mode 0 9 Press to select channel Press to choose the sub channel PRE CH Press to display the previous channel Source Press repeatedly to choose the various input sources Mute Switch the sound On Off VOL VOL Press or to adjust the volume Menu CH CH Press to open the OSD menu Press or to browse through the A V 4 5 OK hannels i i channels Press to select or confirm the various Exit function items on the menu Press to exit the OSD menu Color buttons Display No function Press to show the information about the input source and tuner channel FAV Press to display the Favorite Li
38. st English 25 MTS Press to activate the NTSC tuner sounds such as Stereo SAP Mono tone and languages of the digital tuner Wide Press to choose the display aspect ratio Normal Zoom Wide Cinema Auto Ratio availability varies by video inputs Picture Press to choose the picture mode Dynamic Standard Energy Savings Theater Game Only for E654 E554 model Custom Audio Press to choose sound mode Standard Movie Music News Custom CH List Press to display the Channel List CC Press to activate the Closed Caption Operating Range for the Remote Control Point the top of the remote control toward the LCD TV s remote sensor during button operation Use the remote control within a distance of about 7 m 23 ft from remote control sensor or at a horizontal and vertical angle of within 30 within a distance of about 3 5 m 10 ft E654 AN 30 30 arem T 8 s ole CAUTION o AN 0 30 aao oa E554 E464 E424 E324 Important the remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor or when there is an object in the path English 26 Timing Table FHD E654 E554 E464 Horizontal Vertical E424 Resolution Sync DNI Polarity 640 x 480 60Hz e e e e 720 x 400 70Hz e e e 800 x 600 60Hz e e e 37 879 60 317 o e o 1024
39. the attached specified cables with the E654 E554 E464 E424 E324 color monitor so as not to interfere with radio and television reception 1 Please use the supplied power cord or equivalent to ensure FCC compliance 2 Please use the supplied shielded video signal cable Mini D SUB 15 pin to Mini D SUB 15 pin 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC CAUTION To assure continued compliance and possible undesirable interf
40. urned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so Ventilation The slots and openings in the TV are provided for necessary ventilation To ensure reliable operation of the TV and to protect it from overheating these slots and openings must never be blocked or covered Unless proper ventilation is provided the TV may gather dust and get dirty For proper ventilation observe the following Do not install the TV face up down or sideways Do not install the TV turned over or upside down Never cover the slots and openings with a cloth or other materials Never block the slots and openings by placing the TV on a bed sofa rug or other similar surface Never place the TV in a confined space such as a bookcase or built in cabinet unless proper ventilation is provided Leave some space around the TV set as shown below Otherwise air circulation may be inadequate and will cause overheating which may cause a fire or damage to the TV set English 7 Install on the wall 11

NEC E424

Contents

Download Pdf Manuals

Related Search

Related Contents