La Crosse Technology WS-811561-W wall clock
Contents
1. LCD eoanonanage Lannnnnnnn nni Note Sensor battery voltage must be higher than 2 5V to maintain normal operation When the voltage of the TX61U IT sensor is lower than 2 5V the signal transmission stops and LO is displayed on the LCD for approx 2 seconds before the sensor enters the IDLE mode In IDLE mode the LCD turns off and the sensor charges up the internal rechargeable batteries Page 3 of 12 automatically When the battery voltage charges to 2 5V the LCD will turn on and the transmission of signal will start again 2 Install Batteries into Wireless Display Insert 2 new AA 1 5 volt ALKALINE batteries into the wireless display according to the polarity marked on the battery compartment Make sure to do this within 2 minutes of performing the start up process for the TX61U IT Diagram on page 3 Once the batteries are properly installed in the wireless display the unit will beep and all segments of its LCD will light up briefly The indoor temp and the time displayed as 12 00 will appear on the LCD If it does not appear after 30 seconds please reinstall the wireless display batteries and try again Once the indoor data is displayed proceed to the next step 3 Wireless Temperature Reception After the wireless display is powered up it will start receiving data from the TX61U IT sensor If reception is successful the outdoor temp will appear on the wireless display If the out2. Sensor Location Before permanently fixing the TX61U IT sensor wall bracket temporarily place both the sensor and the wireless display in their desired locations then check that the outdoor temperature reading is being received In the event that the signal is not received relocate the TX61U IT sensor remembering the 200 ft open air wireless range or move both units slightly as this may help the signal reception TX61U IT sensor LCD is turned OFF Pease read step 1 of the Initial Setup section on page 3 or TX61U IT sensor Power Save STOP Mode on page 4 Warranty Information La Crosse Technology Ltd provides a 1 year limited warranty on this product against manufacturing defects in materials and workmanship This limited warranty begins on the original date of purchase is valid only on products purchased and used in North America and only to the original purchaser of this product To receive warranty service the purchaser must contact La Crosse Technology Ltd for problem determination and service procedures Warranty service can only be performed by a La Crosse Technology Ltd authorized service center The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology Ltd or La Crosse Technology Ltd s authorized service center La Crosse Technology Ltd will repair or replace this product at our option and at no charge as stipulated herein with new or reconditione
3. and damage Replace only with new batteries of the recommended type When cleaning the display and casings use a soft damp cloth only Do not use solvents or scouring agents as they may mark the LCD and casings Do not submerge the unit in water Furthermore fix all parts in place where the units are adequately protected against moisture and rain Special care shall be taken when handling a damaged LCD display The liquid crystals can be harmful to user s health Do not make any repair attempts to the unit Contact the La Crosse Technology Warranty Department for help Opening and tampering with the unit may invalidate their guarantee Never touch the exposed electronic circuit of the device as there is a danger of electric shock should it become exposed Do not expose the units to extreme and sudden temperature changes as this may lead to reduce their accuracy Troubleshooting For more product information visit http www lacrossetechnology com 811561 Batteries Battery problems are the single largest cause of customer support cases A few things to check e Use fresh batteries Please use plain Alkaline batteries in the wireless display that test no less than 1 48 on a voltmeter or with an expiration date that is 7 years in the future Page 10 of 12 e Ensure correct polarity Ensure that the wireless display has fresh batteries and are installed using correct polarity as shown inside the battery compartment
4. display in this manual 2 A TX61U IT 915 MHz Wireless Solar Powered Outdoor Temperature Sensor with built in rechargeable battery pack referred to as TX61U IT sensor in this manual 3 Mounting hardware for TX61U IT sensor 4 Instruction manual Features and Specifications Wireless Display e WWYVB radio controlled time manual setting option available DST function on off selectable default is On Wireless outdoor temperature F or C Indoor temperature F or C e Time alarm with 10 minute snooze 12 24 hour time Calendar Month date day e Multi language calendar English US French F Spanish E or d German e Time Zone setting 12 Hours from GMT e Continuous calendar up to year 2029 Low battery indicator e Wall hanging or free standing Indoor measurement range 14 2 F to 99 9 F 9 9 C to 37 8 C w 0 1 C resolution OFL displayed if outside range Indoor temperature update rate Every 16 seconds Batteries 2 X AA size 1 5V not included e Battery life Up to 24 months e 915 MHz Wireless range Up to 200 Ft 60 96m open air e Dimensions 8 9 L x 1 2 W x 7 1 H 227 x 30 1 x 180 mm Page 2 of 12 TX61U IT Wireless Solar Powered Outdoor Sensor e The TX61U IT sensor sends the collected outdoor temperature to your existing wireless display by way of a 200 Ft wireless signal e High efficiency modern solar panel maintains full char
5. 1 To turn the alarm on Press the ALARM button The LCD will display the alarm icon 2 To set the Alarm Time Hour Press and hold down the ALARM button for 2 seconds until the hours digits flash Use the PLUS button to set the hour Press the ALARM button to confirm your setting and move to setting the minutes 3 To set the Alarm Time Minutes Page 6 of 12 The Minutes digits of the Alarm Time will flash Use the PLUS button to set the minutes You can hold the PLUS button in to speed up the setting of minutes by using five minute increments Press the ALARM button to confirm your minutes setting and to end the setting procedure 4 To activate or deactivate the daily alarm Briefly press the ALARM button once When the alarm is active the clock displays the alarm icon below the word TIME when the alarm is deactivated the alarm icon will not display 5 About the Time Alarm After 15 seconds without pressing any button the clock switches automatically from alarm setting mode to normal clock mode The alarm will sound for 85 seconds if not deactivated You can deactivate it by pressing any button The alarm will be repeated automatically after 24 hours The alarm uses 3 different patterns of tone beginning gently and increasing in intensity known as a Crescendo Alarm Battery Replacement Information Wireless Display To replace the batteries in the wireless di
6. La Crosse Technology WS 811561 IT915 MHz Atomic Digital Clock and Temperature Station with Wireless Solar Powered Outdoor Temperature Sensor age ub INDOOR TEMP dz DAY CAT eo SET l nnmnnn Wireless Weather Instruments by La Crosse Technology La Crosse Technology Ltd www lacrossetechnology com 2809 Losey Blvd S La Crosse WI 54601 Phone 608 782 1610 Table of Contents Table of Content ecceeeeeeseeeeeeeeeseeeeeeeessaeeeeeeetaas 1 Inventory of Contents ee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeens 2 Features and Specifications ccccsceesesseeeeeees 2 Initial Set Up and Wireless Synchronization 3 TX61U IT Sensor Power Save STOP Mode 4 Set the Time and Datte ceecceeeceeeeeeeeneeteneeeeneeeeaees 4 Page 1 of 12 Setting the Time Alarm cccccccsssseeeeseeeeeessteeeeseees 6 Battery Replacement Information eeeeeeeeeees 7 Installation Notes mipri anadan ns 8 Mounting the UnItS eeeeereeeereerrrerrrrerrrrsre 9 Online RESOUICES ceceeeeeeeeeeeeeeeeeeseeeeseeeteeeeeeeees 10 Care and Maintenance ccecceeeeeeeeeeeeeeeeteeeeneees 10 Troubleshooting sssi ii aiani ae 10 Warranty Information eeeeeeeeeeeerreerrrrrerrenn 11 Inventory of Contents 1 A WS 811561 IT 915 MHz Temperature Station referred to as wireless
7. US English default setting F French Frangais E Spanish Espa ol d German Deutsch Page 5 of 12 10 11 Set Time Hour Press the SET button a fourth time and the Hours digits will flash Use the PLUS button to select the correct hour Set Time Minute Press the SET button a fifth time and the Minutes digits will flash Use the PLUS button to select the correct minute Set Date Year Press the SET button a sixth time and the Year digits will flash Use the PLUS button to select the correct year Set Date Month Press the SET button a seventh time and the Month digits will flash Use the PLUS button to select the correct month Set Date Date Press the SET button an eighth time and the Date digits will flash Use the PLUS button to set the correct date Set Date Day of Week Press the SET button a ninth time and the Day of Week abbreviation will flash Use the PLUS button to set the correct day of week Set 12 or 24 Hour Time Mode Press the SET button a tenth time and the 12 or 24 Hour Time Mode digits will flash Use the PLUS button to set the time mode to either a 12 or 24 hour clock Set Temperature Mode F or C Press the SET button again and the Temperature Mode abbreviation will flash Use the PLUS button to set the temperature mode to F or C Setting the Time Alarm
8. about every 8 seconds when its battery voltage is higher than 2 5V Once the reset button is pressed on the TX 61U sensor and the batteries are inserted into the wireless display the units will try to synchronize communication If the wireless display fails to receive Page 8 of 12 the outdoor temp this means that the sensor is either located too close or too far from the wireless display Please adjust the location of the TX61U IT sensor and try again If it fails again please restart the set up procedure see below Mounting the Units The TX61U IT Sensor The sensor can be set on a table or mounted onto a wall using the included screws Mounting the Sensor with Screws 1 Remove the mounting bracket from the TX61U IT sensor 2 Place the mounting bracket over the desired location 3 Mark the mounting surface with a PENZ pencil through the two screw holes of the bracket 4 Screw the mounting bracket onto the mounting surface Ensure that the screws are tight against the bracket 5 Insert the TX61U IT sensor into the bracket Table Standing and Other Mounting Options With the mounting bracket installed at the bottom or on the top of the TX61U IT sensor the user can place it on any flat surface IMPORTANT NOTE Before permanently attaching the TX61U IT sensor base place all units in the desired locations t
9. d parts or products if found to be defective during the limited warranty period specified above All replaced parts and products become the property of La Crosse Technology Ltd and must be returned to La Crosse Technology Ltd Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer La Crosse Technology Ltd will pay all expenses for labor and materials for all repairs covered by this warranty If necessary repairs are not covered by this warranty or if a product is examined which is not in need or repair you will be charged for the repairs or examination The owner must pay any shipping charges incurred in getting your La Crosse Technology Ltd product to a La Crosse Technology Ltd authorized service center La Crosse Technology Ltd will pay ground return shipping charges to the owner of the product to a USA address only Your La Crosse Technology Ltd warranty covers all defects in material and workmanship with the following specified exceptions 1 damage caused by accident unreasonable use or neglect including the lack of reasonable and necessary maintenance 2 damage occurring during shipment claims must be presented to the carrier 3 damage to or deterioration of any accessory or decorative Page 11 of 12 surface 4 damage resulting from failure to follow instructions contained in your owner s manual 5 damage resulting from the performance of repairs or altera
10. door temp does not display within 5 min remove the batteries from the display and go back to Step 1 make sure the batteries are fresh 4 Distance Between Units To ensure sufficient wireless communication the final distance between the wireless display and the sensor should be no more than 200 ft 60 96 meters obstacles can reduce this distance TX61U IT Sensor Power Save STOP Mode If the TX61U IT sensor is placed in a dark environment for 24 hours it will enter into the STOP mode to save power The LCD will turn off and it will stop transmitting the data If this happens press the reset button on the TX61U IT sensor to wake it up If the voltage is higher than 2 5V the LCD will turn on again and resume the transmission of the wireless temperature signal If the voltage is lower than 2 5V LO will appear on the LCD and the sensor will enter into IDLE mode Move the sensor to a brightly lit area In IDLE mode the LCD turns off and the sensor charges up the internal rechargeable batteries automatically When the battery voltage charges to 2 5V the LCD will turn on and the transmission of signal will start again Set the Time and Date The WS 811561 Wireless Display will automatically set its time based on daily WWVB reception The signal is Page 4 of 12 attempted at the full hour between 12 00 am to 6 00 am For best reception place the display with the front or back facing Colorado After a successful rece
11. ge with minimal light e Stores solar power for continuous operation e Batteries are a built in non replaceable Alkaline power cell e Wall hanging or free standing e Outdoor measurement range 39 8 F to 139 8 F 39 9 C to 59 9 C with 0 1 C resolution OFL displayed if outside range e Outdoor temperature update rate Every 8 seconds e 915 MHz Wireless range Up to 200 Ft 60 96m open air e Dimensions 1 7 L x 93 W x 3 94 H 43 x 100 x 23 5 mm Signal reception and re synchronization 903MHz 915MHz and 927MHz e Operating voltage 2 5V or higher than 2 5V Initial Set Up and Wireless Synchronization 1 Initialize the Sensor It is important to allow sufficient light to reach the solar panel while activating the sensor Reset button Make sure the lights are on in the setup room and the solar panel is facing a 60W light bulb or brighter do not cover with hands or other objects To begin the set up process use the included plastic reset rod to GENTLY PUSH the reset button once in the hole on the front of the sensor with the LCD solar panel facing a light source All LCD segments will light up briefly The code number and the security code example 20 of the model will be displayed sequentially Next the battery voltage will appear on the LCD Then the current temperature will appear on the sensor s LCD and it will start to transmit the wireless temperature signal Solar cell
12. he sensor but direct rain must be avoided The TX61U IT sensor has a wireless range of 200 feet 60 96 m Keep in mind that the 200 ft range equates to an open air scenario with no obstructions and that radio waves DO NOT curve around objects The actual transmission range will vary depending on the path of the signal Each obstruction roof walls floors ceilings thick trees etc will effectively cut the signal range in half Example If the TX61U IT sensor with a 200 feet 60 96 m range is mounted on an exterior wall the signal must then pass through one exterior wall one interior wall and across the 10 feet 3 m width of the room between the 2 walls to reach the wireless display The first wall will reduce the range to 100 feet 30 48 m and the second wall will reduce the range to 50 feet 15 24 m Factoring in the 10 foot room this leaves a maximum of 40 feet 12 2 m of remaining signal range This allowance is typically enough for a frame wall with non metallic siding however certain materials can reduce range even further Metal siding stucco and some types of glass can reduce signal range by as much as or more compared to the 1 2 reduction typical of most obstructions Itis possible to receive a signal through these materials however maximum range will be much less due to their tendency to absorb or reflect a much larger portion of the sensor s signal The TX61U IT sensor measures and transmits signal
13. hnology com FCC DISCLAIMER This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation All rights reserved This handbook must not be reproduced in any form even in excerpts or duplicated or processed using electronic mechanical or chemical procedures without written permission of the publisher This handbook may contain mistakes and printing errors The information in this handbook is regularly checked and corrections made in the next issue We accept no liability for technical mistakes or printing errors or their consequences All trademarks and patents are acknowledged Page 12 of 12
14. o check that the outdoor temperature readings are being received In the event that the signal is not received relocate the TX61U IT sensor or move them slightly to improve the signal reception The Wireless Display The wireless display can be set on a table or mounted onto a wall Table Standing f er a The two foldout table stands are G oq000 F located on the bottom of the back side of the wireless display 5 B Pull the stands out from the ESN center to fully extend them mN A Wall Mounting fold out legs Select a place to mount the wireless display Install a mounting screw not included Align the Hanging Hole to the mounting screw and ensure that the wireless display locks down into place before releasing the wireless display Page 9 of 12 Online Resources Visit the WS 811561 page online at http Awww lacrossetechnology com 811561 Care and Maintenance Extreme temperatures vibration and shock should be avoided as these may cause damage to the unit and give inaccurate readings Precautions shall be taken when handling the batteries Injuries burns or property damage may be resulted if the batteries are in contact with conducting materials heat corrosive materials or explosives The batteries shall be taken out from the unit before the product is to be stored for a long period of time Immediately remove all low powered batteries to avoid leakage
15. ption no more reception attempt would be made until the following day If the display is in an area of your home where the WWYVB signal cannot be received you can set the date and time manually In either case the Time Zone must be set manually A Note The SET button is used 6 rn gt to enter SET mode The display will exit SET mode automatically after 15 seconds of inactivity loli it oli oli o M Inn Set the Time Zone Press the SET button and the Time Zone display will flash Use the PLUS button to select the desired Time zone setting e 5 EST Eastern default setting e 6 CST Central e 7 MST Mountain e 8 PST Pacific e 9 ALA Alaska e 10 11 12 12 11 10 9 8 7 6 5 4 3 2 1 Other time zones e 0 Greenwich Mean Time GMT e 1 2 3 Other time zones e 4 ATL Atlantic Note North American time zones are negative numbers back view Set Daylight Saving Time ON OFF Press the SET button a second time and DST will flash Press the PLUS button to toggle Daylight Saving Time on On or off OFF Set Language Press the SET button a third time and the Language Abbreviation will flash Press the PLUS button to select the display language A three letter abbreviation for the day of the week will display in the bottom of the LCD as the setting flashes above Language choices include
16. splay 1 Lift up the battery compartment cover and remove the batteries 2 Please take note to install the batteries with the proper polarity as it relates to the battery diagram inside the battery compartment The batteries will fit tightly To avoid start up problems please ensure that the batteries do not spring free 3 Replace compartment cover Please follow the steps listed in the Setup section of this manual to ensure that the wireless data reception is successful The TX61U IT Wireless Solar Powered Sensor Does Not have replaceable batteries The TX61U IT uses solar power and automatically charges the internal power cell s No battery replacement is needed take any used batteries to an authorized depot g Help us to keep our environment clean Please for recycling Page 7 of 12 Installation Notes Point the TX61U IT solar panel toward the best available light source to recharge the batteries but avoid a location in direct sun as it will cause incorrect temperature readings We recommend facing the solar panel East to catch the early morning sun and placing under an eave or overhang to avoid overhead sun The TX61U IT sensor uses internal rechargeable batteries to store the collected solar power The sensor features a high efficiency solar panel that maintains a full charge with minimal indirect light Do not place in direct sun as this will cause incorrect temp readings Fog and mist will not harm t
17. tions by someone other than an authorized La Crosse Technology Ltd authorized service center 6 units used for other than home use 7 applications and uses that this product was not intended or 8 the products inability to receive a signal due to any source of interference This warranty covers only actual defects within the product itself and does not cover the cost of installation or removal from a fixed installation normal set up or adjustments claims based on misrepresentation by the seller or performance variations resulting from installation related circumstances LA CROSSE TECHNOLOGY LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL CONSEQUENTIAL PUNITIVE OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION THIS PRODUCT IS NOT A TOY KEEP OUT OF CHILDREN S REACH This warranty gives you specific legal rights You may also have other rights specific to your State Some States do not allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you For warranty work technical support or information please contact La Crosse Technology Ltd 2817 Losey Blvd S La Crosse WI 54601 Phone 608 782 1610 Fax 608 796 1020 For online contact support e mail www lacrossetechnology com support For information on other products visit www lacrossetec
Download Pdf Manuals
Related Search