Teldat bintec W2004n
Contents
1. Telnet SSH HTTP HTTPS SNMP SNMP v1 v2 v3 USM model VACM views SNMP traps v1 v2 v3 configurable SNMP IP access list configurable Complete management with MIB II MIB 802 11 enterprise MIB Supports SSH V1 5 and SSH V2 0 for secure connections of terminal applications Web based configuration FCI The user interface is identical with almost all bintec elmeg products SSH available HTTPS Telnet protected against bruce force attacks Load and save of configurations save configuration optionally encrypted optional automatic controlled via scheduler No restart is required after the configuration has been changed Software updates free of charge loadable via file HTTP or via direct access to the bintec elmeg upload server optional automatic controlled via scheduler Syslog client with different levels of messaging Automatic eMail alert by definable events predefined events new neighbor AP found new rogue AP found new slave AP found managed AP failed Supported Output via web based configuration interface http https filter subsystem level message bintec W2004n 04 12 2013 Subject to technical alterations Page 8 9 Maintenance Monitoring Interfaces Monitoring WLAN Monitoring Configurable scheduler standalone AP Monitoring Configurable scheduler WLAN Controller Management Supported management systems Management Discovery Protocol Management WLAN Controller funct2. 24 Mbps 17 dBm 36 Mbps 17 dBm 48 Mbps 16 dBm 54 Mbps 16 dBm Tx Power 2 4 GHz 802 11n 20 MSC0 8 16 dBm MSC1 9 16 dBm MCS2 10 16 dBm MCS3 11 16 dBm MCS4 12 16 dBm MSC5 13 MHz 16 dBm MCS6 14 16 dBm MCS7 15 15 dBm Tx Power 2 4 GHz 802 11n 40 MSCO 8 15 dBm MSC1 9 15 dBm MCS2 10 15 dBm MCS3 11 15 dBm MCS4 12 15 dBm MSC5 13 MHz 15 dBm MCS6 14 15 dBm MCS7 15 14 dBm WLAN Standards 802 11b 802 119 802 11n Mimo 3x3 2 4 GHz Receiver Sensitivity 2 4 GHz 6 Mbps 95 dBm 54 Mbps 81 dBm 802 11b g Receiver Sensitivity 2 4 GHz MSCO 95 dBm MCS7 76 dBm MCS8 92dBm MCS15 73dBm MCS16 91dBm MCS23 71dBm 802 11n 20 MHz Extended Performance Feature Beamforming MRC Maximum Ratio Combining Block Acknowlegde Receiver Sensitivity 2 4 GHz MSCO 91 dBm MCS7 73 dBm MCS8 90dBm MCS15 71dBm MCS16 80dBm MCS23 69dBm 802 11n 40 MHz Frequency bands 2 4 GHz 2 4 GHz Indoor Outdoor 2412 2484 MHz max 100 mW EIRP for Germany indoor outdoor EU Data rates for 802 11b g 2 4 11 5 5 2 und 1 Mbps DSSS modulation 54 48 36 24 18 12 9 and 6 Mbps OFDM modulation GHz Data rates for 802 11n 20 MHz MSCO 23 allow up to 216 7 Mbps PHY rate at 20 MHz channel bandwidth 3 streams Short guard channel bandwidth intervall Data rates for 802 11n 40 MHz MSCO 23 allow up to 450 Mbps PHY rate at 40 MHz channel bandwidth 3 streams Short guard channel bandwidth intervall Teldat GmbH Suedwestpark 94 90449 Nuremb
3. a WLAN Controller itself master access point and manage up to six APs The bintec WLAN Controller solution can be used in wireless networks with anywhere from 2 to 150 access points The bintec WLAN Controller solution provides a scalable end to end solution that lets you expand your network without migrating to a new technology This flexibility protects your investments in existing infrastructures The clean lines and elegant design of the W2004n make it an appealing choice for wall or ceiling mounting It looks perfectly at home in high end office spaces hotels and hospitals Despite its handsome appearance this access point also knows how to blend in We ve placed the antennas inside the housing and you can turn off the LEDs to eliminate distractions The included mounting hardware lets you quickly and easily mount the unit onto a ceiling or wall For protection against theft the device is also compatible with Kensington locks As an alternative to wall or ceiling mounting you can also place the device on a desktop thanks to the included rubber feet Take advantage of all the benefits our optional bintec HotSpot solution has to offer when using the W2004n as a stand alone access point or together with the WLAN Controller software Hotspots benefit hotels and restaurants for instance by allowing them to provide controlled wireless access to their customers The W2004n also supports handover and roaming That means with a properly set u
4. total of 5 years including advanced replacement for Teldat products of the category medium Please find a detailed description as well as an overview of the categories on www teldat de servicepackages Wall power supply with EU plug for W1003n W2003n W2003n ext W2004n Wall and ceiling mounting spare part for W1003n W2003n W2003n ext W2004n PoE Injector for LAN 10 100 1000 Mbps 100 240V EU plug output 48V 0 35A suitable for Access Points IP phones etc bintec W2004n 04 12 2013 Subject to technical alterations Page 9 9
5. 0000320 W2004n WLAN Access Point with a dual concurrent radio module according 802 11labgn 2 4 5 GHz Mimo 3x3 2 Gigabit ETH PoE integr antennas incl wall ceiling mounting incl WLAN Controller license for Master AP shipment without 100 240V wall adapter Teldat GmbH Suedwestpark 94 90449 Nuremberg Germany bintec W2004n Phone 49 911 9673 0 Telefax 49 911 688 07 25 04 12 2013 E Mail info teldat de www teldat org Subject to technical alterations Page 3 9 Features Software Roaming at Client Mode Client Band Select Client Management Airtime Fairness Roaming Buffer pool WMM 802 11e QoS WMM 802 11e power save U APSD Internet dialup NTP DNS DHCP HotSpot Operation Modes WLAN operation mode WLAN operation mode WLAN operation mode WLAN Hardware Certifications Standards and certifications LAN WAN WLAN Real time clock Teldat GmbH Suedwestpark 94 90449 Nuremberg Germany Phone 49 911 9673 0 Telefax 49 911 688 07 25 E Mail info teldat de www teldat org VTeldat JI bintec elmeg No roaming normal roaming slow roaming fast roaming user defined roaming Shifting of clients to 5 GHz band Client overload protection to much clients and shifting of clients to other APs if threshold is reached Prevent performance limitation by slower or distant clients which block the network Seamless roaming with IAPP Inter Access Point Protocol suppor
6. 100 1000 Mbps Ethernet twisted pair autosensing auto MDI MDI X One high performance radio module IEEE 802 11bgn Mimo 3x3 and a second high performance radio module IEEE 802 11an Mimo 3x3 allow simultaneous operation at 2 4 100mW and 5 GHz 200 mW Even at power loss the system time will be available for several hours bintec W2004n 04 12 2013 Subject to technical alterations Page 4 9 VTeldat JII bintec elmeg Hardware Power supply External wall power supply 230V 9V DC 1 3A with high efficient switching power supply The wall adapter is a accessory and not include the shipment PoE Power over Ethernet according IEEE 802 3af compatible with 802 3at PoE injectors Status LEDs Status Activity for WLAN1 WLAN2 and Ethernet Wall and ceiling mounting Include the package Desktop operation Possible rubber pad included the package Theft protection Theft protection integrated Kensington compatibel Dimensions Approx 15 9 cm x 14 5 cm x 4 3 cm width x depth x hight Power consumption lt 10 7 Watt Antenna Integrated single band Mimo antenna array with three antenna elements for each radio 5 dBm gain 2 4 GHz 7 dBm gain 5 GHz Environment Temperature operating 0 C to 40 C storage 10 C to 70 C rel humidity 10 to 95 non condensing Wireless LAN Radio 1 Tx Power 2 4 GHz 802 11b g 1 Mbps 14 dBm 2 Mbps 14 dBm 5 5 Mbps 14 dBm 11 Mbps 14 dBm 6 Mbps 17 dBm 9 Mbps 17 dBm 12 Mbps 17 dBm 18 Mbps 17 dBm
7. 250 clients per radio module simultaneously in access point mode Default is 32 clients Channel settings according regulatory domain 802 11d permitted RTS CTS threshold adjustable WEP64 40 Bit key WEP128 104 Bit key WPA personal WPA enterprise WPA2 personal WPA2 enterprise 802 1x EAP MD5 802 1x EAP TLS 802 1x EAP TTLS 802 1x EAP PEAP key management PSK TKIP encryption AES encryption 802 1x EAP MAC address filter for WLAN clients white list and dynamic and static blacklist Black list function requires WLAN Controller Rogue AP detection detect foreign Aps which try to spy out data via SSIDs by permanent background scanning This functionality requires WLAN Controller Rogue Client Detection detection and protection detect conspicuous clients which try to intrude or interfere the wireless network In threat case blocking by dynamic black list This functionality requires WLAN Controller Neighbor AP Detection detection of neighbor Aps with possible influence on performance of own network By detected intrusion SNMP trap or email alert This functionality requires WLAN Controller Network segments on layer2 possible Per SSID one VLAN ID available Static VLAN configuration according IEEE 802 1q up to 32 VLANs supported bintec W2004n 04 12 2013 Subject to technical alterations Page 7 9 Security Inter cell repeating NAT PAT Teldat JII bintec elmeg Inter traffic blocking for public HotSpo
8. CS16 91dBm MCS23 71dBm 802 11n 20 MHz Receiver Sensitivity 5 GHz MSCO 91 dBm MCS7 71 dBm MCS8 89dBm MCS15 69dBm MCS16 87dBm MCS23 67dBm 802 11n 40 MHz Tx Power 5 GHz 802 11a h 6 Mbps 16 dBm 54 Mbps 15 dBm Tx Power 5 GHz 802 11n 20 MSCO 16dBm MCS7 13dBm MCS8 15dBm MCS15 13dBm MCS16 15dBm MCS23 12dBm MHz Tx Power 5 GHz 802 11n 40 MSCO 16dBm MCS7 12dBm MCS8 16dBm MCS15 12dBm MCS16 16dBm MCS23 11dBm MHz Frequency bands 5 GHz indoor 5 GHz indoor 5150 5350 MHz max 200 mW EIRP allowed This information is related to the EU permitted transmission power in Germany The permitted transmission power may vary in other countries Frequency bands 5 GHz outdoor 5 GHz outdoor 5470 5725 MHz max 1000 mW EIRP allowed This information is related to the EU permitted transmission power in Germany The permitted transmission power may vary in other countries Data rates for 802 11a h 5 GHz 54 48 36 24 18 12 9 and 6 Mbps OFDM modulation Teldat GmbH Suedwestpark 94 90449 Nuremberg Germany bintec W2004n Phone 49 911 9673 0 Telefax 49 911 688 07 25 04 12 2013 E Mail info teldat de www teldat org Subject to technical alterations Page 6 9 VTeldat FI bintec elmeg Wireless LAN Radio 2 Data rates for 802 11n 20 MHz channel bandwidth Data rates for 802 11n 40 MHz channel bandwidth Output power limitation without antenna gain Output power 5 GHz Automatic Rate Select
9. WLAN ACCESS POINT High Performance WLAN Access Point bintec W2004n 2 x 450 Mbit s by bintec e High performance radio module for simultar e 802 11n 3x3 Mimo technolgy with up to 2x4 e 200 mW transmitter power at 5 GHz band e Managed by integr WLAN controller or stand e Two Gigabit Ethernet ports with PoE Power ov e Integrated Mimo antennas for 2 4 5 GHZ e Certified for operation in medical environmen WT LZ A A Jeldat bintec W2004n High Performance WLAN Access Point The bintec W2004n is an 11n access point with two single band radio modules allowing the device to operate in both the 2 4 GHz and 5 GHz bands simultaneously The both radio modules with mimo 3x3 technique offer 2x450 Mbps bandwidth Product description The unit is a perfect match for indoor wireless infrastructures designed to provide access over both frequencies Smartphones tablets and older notebooks can connect to the the 2 4 GHz network while high performance notebooks connect to the 5 GHz network CERTIFIED Due to a high performance radio module the W2004n works with up to 200 mW transmission power at the 5 GHz band This is a duplication of the transmission power compared to the 2 4 GHz band You can run the bintec W2004n in any of three different modes You can choose to operate the device as a stand alone access point or manage it from a centrally located bintec WLAN Controller The W2004n can also function as
10. erg Germany bintec W2004n Phone 49 911 9673 0 Telefax 49 911 688 07 25 04 12 2013 E Mail info teldat de www teldat org Subject to technical alterations Page 5 9 VTeldat JII bintec elmeg Wireless LAN Radio 1 Output power limitation Adjustable in following steps 5 8 11 14 16 dBm and maximum Maximal power varies depending without antenna gain on data rate frequency band and country setting Output power 2 4 GHz Max 20dBm Automatic Rate Selection ARS Available Transmission rate Automatic Number of spatial streams 1 2 0r3 802 11n Bandwidth 802 11n 20 40 MHz bundling of two adjoining 20 MHz channels to one 40 MHz channel Short guard interval 802 11n On off switchable increase of throughput by reduction of the guard intervals from 800ns to 400ns DTIM Period Adjustable Multi SSID Up to 8 service sets per radio module with virtual access points and own MAC address per SSID Broadcast SSID On off switchable Power management for clients Registering of up to 250 clients per radio module simultaneously in access point mode Default is 32 clients Country specific settings Channel settings according regulatory domain 802 11d permitted RTS CTS RTS CTS threshold adjustable Wireless LAN Radio 2 WLAN Standards 5 GHz 802 11n Mimo 3x3 5 GHz Receiver Sensitivity 5 GHz 6 Mbps 94 dBm 54 Mbps 81 dBm 802 11a h Receiver Sensitivity 5 GHz MSCO 94 dBm MCS7 76 dBm MCS8 93dBm MCS15 73dBm M
11. ion ARS Transmission rate Number of spatial streams 802 11n Bandwidth 802 11n Short guard interval 802 11n DTIM Period Extended Performance Feature Multi SSID Broadcast SSID Power management for clients Country specific settings RTS CTS Security Encryption WEP WPA IEEE802 11i authentication and encryption Access control list ACL WIDS Wireless Intrution Detection System WIDS Wireless Intrution Detection System WIDS Wireless Intrution Detection System VLAN Teldat GmbH Suedwestpark 94 90449 Nuremberg Germany Phone 49 911 9673 0 Telefax 49 911 688 07 25 E Mail info teldat de www teldat org MSCO 23 allow up to 216 7 Mbps PHY rate at 20 MHz channel bandwidth 3 streams Short guard intervall MSCO 23 allow up to 450 Mbps PHY rate at 40 MHz channel bandwidth 3 streams Short guard intervall Adjustable in following steps 5 8 11 14 16 dBm and maximum Maximal power varies depending on data rate frequency band and country setting Max 23 dBm 200mW EiRP Available Automatic 1 20r 3 20 40 MHz bundling of two adjoining 20 MHz channels to one 40 MHz channel On off switchable increase of throughput by reduction of the guard intervals from 800ns to 400ns Adjustable Beamforming MRC Maximum Ratio Combining Block Acknowlegde Up to 8 service sets per radio module with virtual access points and own MAC address per SSID On off switchable Registering of up to
12. ionallity Documentation Guarantee Accessoires VTeldat JII bintec elmeg Statistic information of all physical and logical interfaces Detailed displays for radio VSS Displayed are per link MAC address IP address TX packets RX packets signal strength for every receiving aerial signal to noise ratio data rate In the operation mode standalone AP the following events can be scheduled Reboot device activate deactivate interface activate deactivate WLAN SSID initiate 5 GHz band scan trigger SW update trigger configuration backup In the operation mode WLAN Controller the following events can be scheduled Activate deactivate WLAN SSID initiate Neighbor band scan WLAN Controller DIME Manager XAdmin CAPWAP DHCP option according RFC1517 Can act as stand alone AP without WLAN controller can act for small installation with up to 6 AP as WTP AC Master AP can act as WTP Managed by a WLAN Controller German and English documentation on CD and in the Internet for download 2 year manufacturer s guarantee online RMA handling Pick up Service Warranty Extension Service Package medium 5500000812 Add ons PS EURO Wx003n Wx004n 5500001254 Wall mounting for Wx003n 4n 5500001278 Gigabit PoE Injector 5530000082 Teldat GmbH Suedwestpark 94 90449 Nuremberg Germany Phone 49 911 9673 0 Telefax 49 911 688 07 25 E Mail info teldat de www teldat org Warranty extension of 3 years to a
13. p and surveyed wireless network managed by a bintec WLAN Controller wireless devices enjoy seamless coverage throughout the network And seamless coverage is a must if you are for instance implementing a VoOWLAN Voice over WLAN solution or using wireless barcode scanners for logistics applications The W2004n gives you green IT right out of the box with its automatic energy saving features If no client is connected the AP turns off any circuits not currently in use downshifting to mimo 1x1 The Gigabit Ethernet ports support the energy saving 802 3az standard ensuring only as much energy as needed is used Teldat GmbH Suedwestpark 94 90449 Nuremberg Germany bintec W2004n Phone 49 911 9673 0 Telefax 49 911 688 07 25 04 12 2013 E Mail info teldat de www teldat org Subject to technical alterations Page 2 9 e Teldat FAT bintec elmeg mI x y x y In addition to the Access Point operation modes the device could be used as WLAN client for direct connecting of ethernet devices e g printers to connect ethernet devices with existing wireless LANS Furthermore it is possible to use the device as bridge in Point to Multipoint operation mode with up to eight links By the fact that a radio module can be used as Access Point and simultaneously as Bridgelink Master it s easy to realize efficient Wireless Backbones It is not possible to use a WLAN Controller at these both operating modes Variants bintec W2004n 551
14. t PHS applications for preventing of communication radio client to radio client in a single radio cell Network amp Port Address Translation Stateful Packet Inspection Isolation of complete network from public access Energy Savining Functions Mimo 1x1 shift down 802 3az support LED Mode Maintenance Configuration a maintenance Configuration a maintenance Device configuration via Configuration a maintenance SNMP Configuration a maintenance SNMP configuration Configuration a maintenance SSH Login Configuration a maintenance HTTP HTTPS Configuration a maintenance Secure configuration Configuration a maintenance Configuration export and import Configuration a maintenance On the fly configuration Configuration a maintenance Software update External Reporting External reporting Syslog External reporting eMail alert External reporting SNMP traps Monitoring Monitoring Internal Log Teldat GmbH Suedwestpark 94 90449 Nuremberg Germany Phone 49 911 9673 0 Telefax 49 911 688 07 25 E Mail info teldat de www teldat org The radio modules switching automatic to Mimo 1x1 operation when no client is connected The ethernet interfaces reduce the power consumption automatically in case that no device is connected In the case of the usage of a short ethernet cable the circuit reduce the transmit power The LEDs has three operation mode Status Flashing Off
15. t according 802 11f For cushioning of peaks Data prioritization for TOS data 802 11e WMM Support of active WLAN clients which support 802 11e power save Unscheduled Automatic Power Save Delivery this functionality contributes significantly to raise battery life of Voice over WLAN end devices PPPoE PPTP works at stand alone operation or with WLAN controller not at Master AP operation NTP client NTP server manually works at stand alone operation or with WLAN controller not at Master AP operation DNS client DNS server DNS relay works at stand alone operation or with WLAN controller not at Master AP operation DHCP client DHCP server DHPC relay DHCP Server and DHCP Relay works at stand alone operation or together with WLAN controller not at Master AP operation Requires a license Works in WLC mode or in stand alone operation but not in Master AP operation WLAN Access Point Managed Access Point Master Access Point for 6 Aps Standalone Access Point Standalone Access Point Bridgelink Master Bridgelink Point to multipoint with up 8 links Transparent WLAN client to connect directly ethernet devices WLAN Radio off WLAN Stand alone Access Point WLAN Managed Access Point WLAN Master Access Point for 6 APs Wi Fi 802 11abgn Certified R amp TTE Directive 1999 5 EG EN 60950 1 IEC60950 EN 300 328 EN 301 489 17 EN 301 489 1 EN 301 893 EN 60601 1 2 medical electrical devices Part 1 2 2 x 10
Download Pdf Manuals
Related Search