iogear GWHDMS52
Contents
1. Problem IR Blaster can t control Source device Solution e Check where is IR sensor is located on the Source device Make sure that the IR Blaster sensor is close and straight in front of the Source device s IR sensor Please refer Installation step 3 for reference setup e Change IR Blaster frequency to meet Source device s requirement See the page 14 for the IR blaster frequency switch Problem No 3D video output OSD displayed Solutions OSD display EI or and ax BE e Check both of TVs includingTx and Rx side should support 3D video format If either one of the TVs only supports 2D format then 3D output might not be supported e f user wants to display 3D video on HDTV which supported 3D video please turn off the 2D HDTV and RE power On the 3D HDTV Then set the source player to 3D video format output for the 3D display e Check the video output setting of Source player ex Blu ray Disc PS3 etc If the video output setting of Source player is 3D video format it might produce a display on the HDTV which not supports 3D format e 3D video format do not support on current equipments status If user wants to display 3D video on HDTV which supported 3D video please turn off 2D HDTV and RE power on 3D HDTV Then set the source player to 3D video format output for the 3D display e 3D video format do not support on current equipments status Please switch the 3D video format to HDMI 1 4a 3D format Please check2. Display 1 x HDMI input Media Source 1 x HDMI output 1 x Component output Transmitter Top view 1 Source LEDs These LED indicators are lit in solid green to show current input 2 Source Selection Button Press to switch Source inputs connected to the transmitter QIOGEAFE Wireless Matrix Back view 1 Power Adapter DC IN 2 IR OUT Blaster Extender Jack Plug the IR Blaster Cable into the IR OUT jack of the transmitter 3 Component IN Optional Connect Transmitter to source device Component port with the provided Adapter Cable 3 Power Button with LED Indicator Press to turn the transmitter on off The indicator in the power button is lit in solid green when the power is on and turns red in standby mode HDMI IN Connect Transmitter to High definition audio video devices via an HDMI cable HDMI OUT Connect to an HDTV via an HDMI cable Mini USB Port For USB HID connection Keyboard Mouse control Connect to USB enabled laptop or computer TRANSMITTER Receiver Top view 1 Power Button with LED indicator Press to turn the receiver On and Off The indicator in the power button lights Up in green when the power is on and turns red in standby mode 2 Source Button Press this button for Source device input selection GIOGEFAR Wireless Back view 1 Power Adapter DC IN Connect to receiver s power adapter 2 USB HID Support USB HID function for
3. 16 24 bits audio sample with 832 96KHz sampling rate as below 2channel PCM 32KHz 44 1KHz 48KHz 96KHz 16 bits YES YES YES YES 24 bits YES YES YES YES Specifications Supported Video HDMI Input 3D 1080p 10601 7200 5760 480p mace Wael Component Input 1080i 720p 576p 576i 480p 480i Supported Audio Digital Audio Up to 6 Mbps AC3 and DTS POTRDI Analog Audio 48KHz and 24 bit Per Sample Transmission Distance The maximum video transmission range is100ft The minimum range is 6 5ft Line of sight LOS scenarios Remote Control Range 30 feet LOS System Latency Very low latency lt 1ms Antenna Operating Frequencies High Performance Internal Antennas 4 9 5 9GHz Include non DFS and DFS Frequency Bands Power Supply 100 240V AC in 5V DC out Power Adaptor Operating Temperature Interfaces A V Interfaces HDMI Input 0 40 C Transmitter Tx Four Type A Receiver Rx Component Input One w specific adapter cable HDMI Output One Type A One Type A Control Signal IR Sensor YES YES no IR Blaster Extender 2 5mm Jack IR Sensor Extender 2 5mm Jack Power Interface Power Input 5V DC Jack 5V mini USB Two Tone Green Red Switches Power Switch YES One Push Button YES One Push Button Source Switch YES One Push Button YES One Push Button LEDs Power LED 1 x LED 1 x LED Two Ton
4. remote signal protocol 14 Step 4 Mounting the Receiver to a Wall Optional 1 Refer the drawing at right that has relative position of the main holes that will be needed to be drilled into the wall 2 Drill two 1 4 pilot holes 3 Insert the supplied two Anchors into the wall If necessary use a small hammer to lightly tap the anchors flush to the wall 4 Insert two screws into the anchors Leave 1 4 length for mounting the Transmitter 5 8 for the Receiver 5 Place receiver main holes over the protruding screws and slide down into position S la Sinen Ah T Basic Operation 1 After the power adapter is plugged into the electrical outlet the device will turn ON automatically 2 If the receiver is in Standby mode POWER LED on the receiver is lit in red press the POWER button ON to the receiver and then transmitter and receiver will establish link automatically You may also turn POWER ON to the receiver with the remote control Please note that the HDMI out on the transmitter will always be ON even when the transmitter is in standby mode 3 Power ON all connected displays ie TV monitor projector and source devices ie cable box Blu ray player game console computer 16 4 During warm up the transmitter s and the receiver s wireless status LED will blink green until the signal link between the transmitter and the receiver is established It will take approxima
5. Primary CEA Video Timing 640x480p 59 94 GOHz YES 720x480p 59 94Hz 480p YES 720x480p 60Hz YES 720x576p 50Hz 576p YES 1280x720p 50Hz 720p YES 1280x720p 59 94 60Hz YES 1920x1080i 50Hz YES 1920x1080i 59 94 60Hz YES 1920x1080p 50Hz YES 1080p 60 1920x1080p 59 94 60Hz YES Secondary CEA Video Timing 1920x1080p 23 98 24Hz 1920x1080p 25Hz 1080p 24 1920x1080p 29 97 30Hz VESA Timing DVI only 640x480 59 94 72 809Hz VGA 800x600 60 317 72 188HZ SVGA 1024x768 60 70 069Hz XGA 1280x768 60 Hz WXGA 1280x1024 60 Hz SXGA 26 If the Source Status LED continues to blink green slower than no signal mode or OSD display shows B please check that both TVs connected to the transmitter and receiver support 3D video format and try to switch the 3D video format to one of the 3D timings listed below 1280x720p 50Hz Top and Bottom Yes 1280x720p 50Hz Frame packing Yes 1280x720p 59 94 60Hz Top and Bottom Yes 1280x720p 59 94 60Hz Frame packing Yes 1920x1080i 50Hz Side by Side Half Yes 1920x1080i 59 94 60Hz Side by Side Half Yes 1920x1080p 23 98 24Hz Top and Bottom Yes 1920x1080p 23 98 24Hz Frame packing Yes Audio Bit Rate Support e Digital Audio from HDMI inputs Up to 6Mbit s bit rate support e Support AC3 and DTS e 2 channel PCM
6. et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps i les dispositifs fonctionnant dans la bande 5 150 5 250 MHz sont r serv s uniquement pour une utilisation a l int rieur afin de r duire les risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux li De plus les utilisateurs devraient aussi tre avis s que les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux c d qu ils ont la priorit pour les bandes 5 250 5 350 MHz et 5470 5600MHZ 5650 5725MHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL En vertu de la r glementation de l industrie du Canada cet metteur de radio ne peut fonctionner l aide d une antenne d un type et un maximum ou moins Gain approuv pour l metteur par Industrie Canada Pour r duire le risque d interf rence aux autres utilisateurs le type d antenne et son gain doivent tre choisis afin que la puissance isotrope rayonn e quivalente PIRE ne d passe pas ce qui est n cessaire pour une communication r ussie Introduction IOGEAR s GWHDMS52 Wireless 5 x 2 HD Matrix is the first to send Full uncompressed HD 1080p connects up to 5 source devices and allow you to switch and independently select any source between 2 HDTVs The wireless matrix feature is the biggest breakthough in wireless AV soluti
7. keyboard mouse usage Matrix Video status LED For video input status indication Please refer to page 19 section 7 for the detailed information Wireless status LED For wireless link status indication Please refer to page 19 section 7 for the detailed information HDMI OUT Connect to an HDTV via an HDMI cable IR IN Available to connect IR sensor extender cable 10 Remote Control a Matrix QIOGEAF POWER ON POWER OFF Buttons Press Power ON to turn the Transmitter amp Receiver ON Press Power OFF to turn the Transmitter amp Receiver OFF When both Transmitter amp Receiver Power LEDs are red press Power ON to the Receiver to wake up both the Receiver and Transmitter automatically INFO Button Press this button to the Transmitter or Receiver to display OSD for system related information on HDTV TRANSMITTER NO Button Press to switch different transmitter inputs Please refer to page 24 Multiple Transmitter Selection section SOURCE Button Press to select the audio video source inputs to the Transmitter or Receiver Press OK to switch to the source input selected Up and Down Arrow Buttons Press to select the audio video source inputs for transmitter display Press OK to switch to the source input selected Left and Right Arrow Buttons Press to select the audio video source inputs for receiver display Press OK to switch to the source input selecte
8. page 27 for a list of all supported 3D format of this product 30 Federal Communications Commission FCC Statement The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions CE Compliance This device has been tested and found to comply with the following European Union directives Electromagnetic Capability 2004 108 EC Low Voltage 2006 95 EC and R amp TTED 1999 5 EC Limited Warranty WE RE HERE TO HELP YOU NEED ASSISTANCE SETTING UP THIS PRODUCT Make sure you 1 Visit www iogear com for more product information 2 Visit www iogear com support for live helo and product support Warranty Information This product carries a 1 Year Limited oo For the terms and conditions of this warranty please go to http www iogear com support warranty Register online at http www iogear com register Important Product Information Product Model Serial Number Contact IOGEAR iogear custhelp com support iogear com www iogear com 19641 Da Vinci Foothill Ranch CA 92610 31 GIDGEAFE
9. regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication IMPORTANT NOTE e In the event that these conditions can not be met for example certain laptop configurations or co location with another transmitter then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product In these circumstances the OEM integrator will be responsible for re evaluating the end product including the transmitter and obtaining a separate Canada authorization French translation Ce dispositif est conforme a la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage re u y compris un brouillage susceptible de provoquer un fonctionnement ind sirable NOTE IMPORTANTE D claration d exposition aux radiations Cet quipement est conforme aux limites d exposition aux rayonnements IC tablies pour un environnement non contr l Cet quipement doit tre install
10. 720p 576p or 480p resolution Please refer page 26 for the detail supported Resolution POWER LED in solid Green Ensure the proper cables are connected between status LED Flash Quickly the transmitter and your AV source devices OSD displayed e Ensure your source devices connected to the transmitter are powered on ry N e Ensure the proper cables are connected between the receiver and your 2nd HDTV near the receiver Px 3 Problem Poor picture quality or intermittent video Solutions e Check if your video resolution with HDMI input from your device is either 1080p 1080i 720p 576p or 480p Please refer to page 26 where the video frame rate from your device GWHDMS52 can support is defined e Ensure the transmission distance is less than 100 feet LOS e Barriers Consider an installation plan that has the least numbers of barriers walls panels beams possible between the transmitter and receiver Distances quality and signal may vary depending on environment solid objects such as steel concrete and brick may view shorter distances or complete loss of singal 29 Problem No audio Solution e Check your TV s volume is properly set and not set in MUTE mode e Check if your source player s audio volume has been turned up e Ensure the bit rate of audio from the source device can be supported by GWHDMS52 Please refer to the details in page 27 Audio Bit Rate Support
11. QIOGEAFZ User Manual Wireless 5x2 HD Matrix GWHDMS52 PART NO M1229 b wWww iogear com 2014 IOGEAR Part No M1229 b IOGEAR the IOGEAR logo are trademarks or registered trademarks of IOGEAR Microsoft and Windows are registered trademarks of Microsoft Corporation All other brand and product names are trademarks or registered trademarks of their respective holders IOGEAR makes no warranty of any kind with regards to the information presented in this document All information furnished here is for informational purposes only and is subject to change without notice IOGEAR assumes no responsibility for any inaccuracies or errors that may appear in this document Table of Contents Important Information Introduction Package Contents Requirements Overview Hardware Installation Step 1 Setup the Transmitter Step 2 Setup the Receiver Step 3 Setup the IR blaster extender cable and IR sensor extender cable Step 4 Mounting the Receiver to a Wall Optional Basic Operation Advanced Operation Naming the Input Source Devices Pairing new transmitter with existing receiver optional Multiple Transmitter Selection Supported Resolution Audio Bit Rate Support Specifications Troubleshooting Federal Communications Commission FCC Statement CE Compliance Limited Warranty Contact o oO A 12 13 14 15 116 22 22 23 24 26 2m 28 29 31 31 31 31 Important Information Please take the time to read thi
12. Use of this product in the following locations may result in abnormal video and audio output noise blocked image etc 1 Product installed in the walls made of concrete 2 Product is situated near the refrigerator or metal fitment 3 A cluttered room where the wireless signals may be blocked e This product has been tested and manufactured to comply with each country s safety rules However there is no guarantee that interference will not occur in some installation scenario If the interference happens increase the distance between the transmitter and receiver e GWHDMS52 may interfere 5GHz wireless devices such as routers or other wireless devices Therefore if you have an 802 11n router configure it to the 2 4 GHz band rather than the 5GHz band e Optimal range between GWHDMS52 transmitter and receiver is between 2 and 20 meters within line of sight System Warning FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not oc
13. cur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CAUTION Using the System in the US e Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment e This equipment must be installed and operated in accordance with provided instructions and the antenna s used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter End users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance e Outdoor operations in the 5150 5250MHz band are prohibited e This device has no Ad hoc capability for 5250 5350MHz and 5470 5725MHz e The device not operation in 5600 5650MHz e This device complies with Part 15 of the FCC Ru
14. d IR Button Press to switch the IR Blaster frequency to meet Source device s requirement It can switch the IR Blaster frequency from 47KHz to 56KHZ to 38KHZ recurring Battery Compartment e Remove the remote control battery door by pushing the bottom clip in and lifting on the battery door e Place the two AAA batteries into the remote control and replace the battery door until it snaps in place Hardware Installation Step 1 Setup the Transmitter Connect up to 5 Audio Video Source Devices and a HDTV to the transmitter DMI 1 HDMI 2 HDMI 3 HDMI4 HDMIOUT USB Le Home PC IR Blaster A HD Projector or HD Flat Panel TV ay HD Gaming Box HD Cable Box ee FIN Playor Connect the supplied power adapter 4 Connect up to 4 High Definition HD AV to the DC IN jack of the transmitter and sources via HDMI OUT through by a wall socket The LED indicator in the HDMI cable POWER button lights up in green when it 5 Connect the transmitter s HDMI OUT is connected to power to the local HDTV HDMI IN port with an Plug in the provided IR blaster cable HDMI cable Please refer to page 14 step 3 for the 6 Connect the mini USB port to the USB detail setup instruction port of PC or Notebook with a mini USB Connect to source device through by to Type A USB cable for USB HID control Component YPbPr Adapter cable keyboard mouse on receiver side 12 Step 2 Setu
15. e Green Red Source LED Tx Status LED Rx 5 x Green LEDs 2 x Green LEDs Video signal Wireless signal Dimensions inches mm PAS En 1 28 a 234mm x 96 5mm x 32 5mm 28 STAM XITA a al 95mm x 95mm x 35 5mm Troubleshooting 1 Problem The power indicator LED doesn t light up Solution Check the power adapters of the Transmitter Receiver to see if they are properly inserted into a functioning power outlet 2 Problem No video is displayed on your TV screen Solution e Verify that the proper cables have been selected and installed between the transmitter input and your High Definition device output e On your TV side connected to the Receiver select the HDMI as input source e Verify the status of POWER LED and SOURCE Status LED indicator as below Power LED Flashing in e Ensure the transmission range between the Green transmitter and the receiver is NOT over 100 feet OSD displayed LOS line of sight transmission distance 4 levels looping e Try to move the transmitter closer to the receiver amp N POWER LED in solid e Ensure your video resolution and frame rate is Green Slow and Flashing recognized supported and within the transmission SOURCE LED range OSD displayed e Connect the source device to your TV to check and modify the video format compatibility e Check if the video resolution from your display is set a N to 1080p 1080i
16. emote control of your devices from another room when using the wireless receiver IR Blaster Extender cable Blu ray Player or DVR Cable Box Note Transmitter and source devices connected to the Transmitter within the local location must all be in line of site for IR control B Receiver 1 Place the wireless receiver out of sight and use the IR Sensor extender for remote control of your devices 2 Plug the IR Sensor Extender cable into the IR IN jack of the receiver and place sensor on front of the TV for convenient operation Note In some instances the IR sensor on your source device may be difficult to find To help simplify this process cut a piece of cardboard to the same size as the front panel of your source device and place a 1 inch hole in the middle of the cardboard Power ON your source device and play a movie or other video content Place the cardboard hole over the left side of the source device and using the source device s remote control directly over the cardboard hole press the pause button repetitively while gradually moving the cardboard hole from left to right making sure to keep the remote control s beam directly over the cardboard hole Once the source device recognizes the pause button being pressed you have located the position of the remote control IR sensor on the source device and that is where you will place the IR Blaster s sensor The IR sensor supports 38KHz 47KHz and 56KHz NEC RC5 RC6
17. es Keep pressing the SOURCE button until the desired input source is selected Note Pressing Up or Down on receiver side or pressing Left or Right on transmitter side will not initiate switching 18 7 lf operation is normal the POWER Wireless status LED and Source Status LED will glow in solid green Please refer to the LED status table below that contains detailed LED indicator and OSD descriptions for the transmitter and receiver Status Tx Rx Tx Rx Rx Rx Item Mode Description Power Source Video Wireless OSD Display p LED LED LED LED Standby For power saving Static ia mode Red Initial Boot up Warm It will soend 15 Sine 3 levels up 20 seconds for Green Blinking Blinking Blinking ne system boot Up Rx Static Green Searching Continuing search TX available available channels Blinkin channels If system can t 9 _ TANE i Green Blinking Blinking establish link N Rx Static over 80s after CE Looping display initialization these two OSD wrake No input from linked Mode P Static Blinking Blinking Static selected source Note B Green Quickly Quickly Green is not Static Blinking Blinking Static Note C Green Slowly Slowly Green Video format is Static Static Static Static recognized Green Green Green Green Notes A lf the RF connection boot up has exceeded 80 seconds and still not established a link between the transmitter and receiver it is due ei
18. evices 1 Press and hold the Source button on the top of transmitter for over 3 seconds source naming OSD will appear on the screen High Def Flat panel TV 2 The current source input may be named by pointing the remote control at the transmitter and using the remote control 4 keys to change the letters or numbers keys to move the cursor Moves the cursor left or right Changes letters and numbers 3 After completing source naming please press the source key on the remote control or on the top of transmitter housing to confirm and save the new source name 4 You will see the new source name on the OSD for both transmitter and receiver each time the source with the new name is selected 22 Pairing new transmitter with existing receiver optional Enter the Pairing mode for transmitter 1 Unplug Power Adapter from the transmitter 2 Press and hold down the Power button on the transmitter 3 Plug in Power adapter to the transmitter 4 Keep holding down the Power button on the transmitter until the power LED is blinking orange indicating that the transmitter has entered the Pairing mode Use the same operation method of the receiver to enter the pairing mode Once the receiver enters the pairing mode the OSD shows Searching Both transmitter and receiver will enter the Pairing mode and it will search and pair automatically The OSD shows Adding GWHDMS52 eo Once the pairing
19. is finished both transmitter and receiver will re boot and link to each other automatically 23 Multiple Transmitter Selection 1 Verify that the power is removed from Transmitter 1 Press Transmitter No key on the remote control and point it at Receiver 1 OSD Displays Select Transmitter Number GWHDMS52 GWHDMS52 ox SETUP Up to 4 transmitters may be detected Press up down and OK button on remote control for selection 2 Enter SETUP menu OSD Displays SETUP Add New Transmitter Remove Transmitter Modify Transmitter Name 9 Return 3 Enter Add New Transmitter menu if you would like to add a Transmitter OSD Displays Press transmitter no key to escape SEARCHING SEARCHING During this period press and hold the power down on Transmitter 2 and plug in power Hold the power button down until the Power LED on Transmitter 2 start to blink orange which indicates that the Transmitter 2 has entered the connecting mode After the receiver has found the new transmitter the OSD Displays Select New Transmitter GWHDMS52 9 Return 24 Once Transmitter 2 and Receiver 1 are connected and video is displayed you may apply power to Transmitter 1 Receiver 1 will now see 2 transmitters and can be selected via the Transmitter No button on the remote control To add Transmitter 3 and 4 repeat steps 1 4 Note You may connect multiple transmitters but you may onl
20. it the INFO OSD OSD Displays P N HDMI1 CH1 1280x1024 F W or 3 Press the SOURCE button on the remote control or on the top of transmitter or receiver for audio video source input selection OSD Displays al N HDMI1 CH1 1280x1024 4 Press the IR button and then the Up and Down keys on the remote control to change the IR Blaster frequency The IR frequency can be switched from 47KHz to 56KHZ and to 38KHZ recurring Note that the IR blaster frequency default setting is 47KHz Press once for current IR frequency status display N HDMI1 CH1 1280x1024 If a7Kuz OSD Displays Press IR key again to switch IR blaster frequency OSD Displays i N HDMI1 CH1 1280x1024 If 56KHZ 8 USB HID Setup Instructions You can conveniently control your computer connected to the transmitter from the receiver side wirelessly via the GWHDMS52 USB connections 1 Transmitter Using a Mini USB to USB Type A USB cable Plug the mini USB side into the transmitter and the USB type A into the computer you wish to control jal HI HIMA DAICUI LER HDMI cable Receiver You can connect either a USB based Keyboard or Mouse to the USB port on the back of the receiver IOGEAR Wireless AV Multimedia Keyboards with trackball makes a perfect companion GKM561R GKM681R GKM581R and GKM571R S HDMI OUT IRIN 21 Advanced Operation Naming the Input Source D
21. les Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Statement The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions A Industry Canada Statement This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Radiation Exposure Statement This equipment complies with IC radiation exposure limits set for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body Caution 1 the device for operation in the band 5150 5250 MHz is only for indoor use to reduce the potential for harmful interference to co channel mobile satellite systems 2 High power radars are allocated as primary users i e priority users of the bands 5250 5350 MHz and 5470 5600MHz 5650 5725MHz and that these radars could cause interference and or damage to LE LAN devices Under Industry Canada
22. ons today This means you can watch cable TV in the living room while independently select a Blu ray movie to watch in the bedroom at the same time Its capable of streaming Full HD 1080p with support for 3D content and digital audio up to 100 feet away within the home or desired set up The Wireless 5 x 2 HD Matrix is setting a new standard in wireless connectivity flexibility convenience and decor The solution consists of a Wireless Transmitter and a Wireless Receiver with connections for HDMI and Component along with a loop through local port for an advanced 2 HDTV set ups It also includes USB connectivity for the addition of a computer laptop giving you wireless control from the second room Infrared IR pass through enables wireless control of your source devices and helps consolidate your HD A V electronics such as a DVD Blu ray players DVR Cable boxes Game consoles and computers to design your own custom entertainment space The Wireless 5 x 2 HD Matrix does not require a line of sight placement keeping home theater devices neatly out of sight which enables a quick simple and flexible wireless HD or 3D audio video solution Package Contents 1 x Wireless Transmitter 2 x Power Adapter 1 x Wireless Receiver 1 x HDMI Cable 2 x Remote Controls w batteries 1 x User s Guide 1 x Component Adapter Cable 1 x Warranty Card 1 x IR Blaster Cable Transmitter 1 x IR Sensor Extender Cable Receiver Requirements
23. p the Receiver HDTV Connection with receiver HDMI OUT IRIN 1 Connect the supplied mini USB power adapter to the DC IN jack of the receiver and a wall socket The POWER LED indicator lights up in green when the receiver is connected to power 2 Connect either a USB based Keyboard or Mouse to the USB port on the back of the receiver IOGEAR Wireless AV Multimedia Keyboards with trackball make a perfect companion GKM561R GKM681R GKM581R and GKM571R HD Projector or HD Flat Penel TV 3 Connect an HDMI cable to the HDMI OUT jack of the receiver and to the HDMI IN on the HDTV or an HD projector Press the Source button on your receiver or the left and right arrows button on the remote to select the appropriate HDMI video input 4 Plug in the IR sensor extender cable provided Please refer to page 14 Step 3 of the Hardware Installation section Step 3 Setup the IR blaster extender cable and IR sensor extender cable The IR relays infrared commands from your remote control to your device Users can control their AV devices by pointing their remote control to the receiver or IR sensor extender cable IR distance from remote to receiver IR sensor cable is 30 feet line of sight A Transmitter 1 Plug the IR Blaster cable in to the IR Out jack of the transmitter 2 Apply the IR blaster head directly over the eye of the IR sensor of your High Definition audio video device This allows the r
24. s user manual before using the Transmitter and Receiver It contains important information about operating your Full HD video wireless kit Our limited warranty applies when the product is handled properly for intended use in accordance with its operating instruction However the warranty may be void in the following cases e Repair product modification or alteration have been performed by unauthorized service personnel e Damages caused by accidents including but not limited to lightning water fire or moisture e Use of an AC adapter not compatible with the product and its voltage rating e The model number on the product has been altered deleted removed or made illegible Safety Precautions Warning RISK OF ELECTRICAL SHOCK DO NOT OPEN A TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE THE COVER NO USER SERVICEABLE PARTS ARE INSIDE REFER SERVICING TO QUALIFIED PERSONNEL A Danger Be careful with electricity e Power to the units must be switched off before any work is undertaken such as any AV device connection or TV connection e Power outlet To prevent electric shock make sure to use the appropriate AC adapters as power supply to the transmitter and the receiver Power cord Be sure the power cord is routed so that it will not be stepped on or pinched by heavy items Power overloading Avoid overloading electrical outlets or extension cords which otherwise could result in elec
25. tely 15 20 seconds for system to fully boot up successfully 5 Ensure your TV or projector is in HDMI input mode 6 When the GWHDMS52 is first powered on the input default is set to Source 1 Note that any time a source input is switched it will take approximately 15 20 seconds for the image to appear There are 3 ways to switch between connected source devices as follows A Press the SOURCE button on the top of the receiver or transmitter to switch the source inputs until you see the desire video program being broadcasted from your source device es gt B Remote Arrow Keys Switching e Transmitter side Press By pressing the Up or Down arrow keys on the remote control it will pop up the on screen display and allow you to cycle through each input Stop on the one you wish to watch and it will switch to that direct input source device High Def Flat panel TV OSD Displayed TX OUT HDMI1 CH 1080p voor v gt OK e Receiver side By pressing the C2 co Left or Right arrow keys on the La remote control it will pop up the sais on screen display and allow you to cycle through each input Stop on the one you wish to watch and it will switch to that direct input source device Receiver Source Switch Left Right arrow buttons C Remote Control Source Button Press the SOURCE button on the remote control to directly switch between connected input sourc
26. ther to lost link or the transmitter is most likely out of range You may have to verify the range and adjust or shorten the distance between your HDTV set with the transmitter and the receiver The maximum video transmission range for 1080p content is up to 100 feet in line of sight LOS The minimum range is 6 5 feet B Please make sure the source device has been powered ON and the signal output is set to HDMI out also try to re plug the HDMI cable to make sure the HDMI connector had seated properly C If there is no video displayed and OSD display shows Not Supported Format this is an indication that the video resolution or frame rate from the computer is not supported please refer to page 26 to switch to a supported video resolution D If you have more than one pair of this product each transmitter and receiver should be at least 6 5 feet away from one another E On Screen Display OSD vs Remote Control Instruction 1 In Active mode press the POWER button on the top of receiver or transmitter or press the remote controls Power button and point it to the receiver or transmitter both receiver and transmitter will enter Standby mode and transmitter s HDMI out remains on OSD Displays Display 3secs and then enter Standby mode A BO 1 on Press the INFO button on the remote control to display signal quality source channel and resolution information for user reference Press the INFO button again to ex
27. tric shock or fire Lightning Disconnect the product from the power source if it is left unattended for a long period of time and to protect the product from lightning Always disconnect the power cord from the power outlet when you are not using your Full HD Video wireless kit This reduces the risk of electric shocks or fire A Warning This product should not be exposed to dripping or splashing No object filled with liquids such as vases should be placed on the product Object Entry To avoid electric shock never stick anything in the slots on the case or remove the cover Place receiver transmitter on a flat hard and stable surface Ventilation Do not block the ventilation slots on the receiver transmitter or place any heavy object on the top cover Blocking the air flow could damage the receiver Arrange components so that air can flow freely around the receiver Ensure that there is adequate ventilation if the receiver is placed in a stand Put the receiver transmitter in a property ventilated area away from direct sunlight or any source of heat Water Exposure To reduce the risk of fire or electric shock do not expose the receiver transmitter to rain or moisture This is indoor solution Our company has the right to modify this document without any notice Special Notice e Never use this product nearby an aircraft or medical facility It can cause interference or undesirable effect on the operation result e
28. y have one receiver running at any given time When Receiver 1 is connected to Transmitter 2 Receiver 2 will be disconnected and need to be re paired to restore wireless video function with Transmitter 2 4 Enter Remove Transmitter menu if you would like to remove a transmitter OSD Displays Remove Transmitter gt GWHDMS52 Using the remote control press the up down GWHDMS52 arrow keys to select the transmitter to be removed and press OK 9 Return 5 Enter Modify Transmitter Name menu if you would like to modify a transmitter name OSD shows Edit Transmitter name gt GWHDMSs2 Using the remote control press the up GWHDMS52 down arrow keys to select the transmitter to have its name modified and press OK 9 Return Edit Transmitter name GWHDMS52 9 Return IR Key Delete Tt tb A Z 0 9 D cursor Press the Up Down keys on the remote to select alphabet characters Press the Left Right keys on the remote to move the cursor Press IR key to back space 25 Supported Resolution If the SOURCE LED continues to blink in green slower than no signal mode OSD display Sx O and there is no video displayed or the video quality suffers it indicates that the video frame rate from your A V source device is not supported Ensure that the consumer timing of your HDMI device is compliant with the standard listed below 2D Video Format Timings Resolution S100 00 g
Download Pdf Manuals
Related Search