Gefen EXT-CAT5-4000
Contents
1. Geren ee Extender EXT CATS 4000 User Manual ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday Write To Gefen Inc c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice CAT5 4000 Extender is a trademark of Gefen Inc 2009 Gefen Inc All Rights Reserved All trademarks are the property of their respective companies Rev A2 Pb c O N O 11 12 13 14 15 16 CONTENTS Introduction Operation Notes Features Sender Panel Layout Sender Panel Descriptions Sender Panel Descriptions Notes Intensionally Left Blank Receiver Panel Layout Receiver Panel Descriptions Connecting The CAT5 4000 Extender Analog VGA Connecting Adjusting The CAT5 4000 Analog VGA Connecting The CAT5 4000 Extender Digital DVI Connecting Adjusting The CAT5 4000 Digital DVI RS 232 Serial Communication Configuration Specifications Warranty INTRODUCTION Congratulations on your purchase of the CAT5 4000 Extender Your complete satisfaction is very important to us Gefen Gefen delivers innovative progressive computer and electronics add on solutions that harness integration extension distr2. DVI RS 232 and VGA Audio RJ 45 Ports These RJ 45 ports connect the CAT5 4000 receiver to the CAT5 4000 sender unit using CAT 5 CAT 5e or CAT 6 cabling When using an analog or digital video source on the channel 1 input connect the CAT 5 cables according to the labels on both the sender and receiver units When using an analog video source with the channel 2 or 3 inputs connect a CAT 5 cable from the VGA RS 232 RJ 45 port on the sender unit to the VGA Audio RJ 45 port on the receiver unit When using a digital video source with the channel 2 or 3 inputs connect a CAT 5 cable from the DVI DDC RJ 45 port on the sender unit to the DVI RS 232 RJ 45 port on the receiver unit Additionally if RS 232 extension is required when using a digital video source on channel 2 or 3 a second CAT 5 cable must be used to connect the VGA RS 232 RJ 45 port on the sender unit to the VGA Audio RJ 45 port on the receiver unit Analog Stereo Audio RCA Outputs When using the CAT5 4000 receiver unit with channel 1 audio will be transmitted to these RCA outputs Connect an amplified audio output device to these RCA output connectors RS 232 Serial Communication Output This output will support a RS 232 serial communications device Only pins 2 RX 3 TX and ground 5 are supported This output will only be available when the proper RJ 45 connections for RS 232 functionality are present The CAT5 4000 receiver units must be configured for RS 232 operation fo
3. be lit on the sender unit and all receiver units NOTE There are status indicators above each RJ 45 port Green indicators will be active when the DVI Clock is present Red indicators will be active when the receiver detects a display or Hot Plug Detect The receiver s Red indictor will indicate the current position for DIP switch 1 on the receiver please see page 14 for more information Adjusting the CAT5 4000 Extender Using an Digital DVI Source The CAT5 4000 was designed for plug and play installation However differences in CAT 5 cabling quality and skew rates may require the user to adjust the equalization setting to obtain a video output If there is no video output or if the video output is not stable please follow the instructions below to adjust the equalization 1 Locate the Equalization adjustment dial on the front panel of the CAT5 4000 receiver 2 Insert a small flat head tool into the Equalization dial 3 Turn the dial in either a clockwise or counter clockwise direction until the desired adjustment level is reached The Equalization has 16 positions 0 9 and then A F that can be set The dial will click into each position Please ensure that the dial is set to one of the positions and is not in between two positions 4 Remove the adjustment tool from the Equalization dial 13 RS 232 SERIAL COMMUNICATION CONFIGURATION RS 232 Serial Control The RS 232 transmission from the CAT5 4000 receive
4. port is used When the input source is digital the DVI DDC port is used If RS 232 is required when using a digital input source use both RJ 45 ports Channel 3 DVI Input Connect an analog or digital source to this DVI I input port 5V DC Power Receptacle Connect the included 5V DC power supply between this input and an open wall power socket NOTES INTENTIONALLY LEFT BLANK RECEIVER PANEL LAYOUT Front Panel Back Panel RECEIVER PANEL DESCRIPTIONS Brightness Trim Pot When using an analog input video source use this Trim Pot to brighten darken the output video Please see page 11 for detailed instructions on the usage Focus Trim Pot When using an analog input video source use this Trim Pot to blur sharpen the output video Please see page 11 for detailed instructions on the usage Equalization Dial When using a digital input video source use this equalization dial to tune the incoming video signal Please see page 13 for detailed instructions on the usage Power LED Indicator This LED will become active once the included 5V DC power supply is properly connected between the unit and an open wall power socket 5V DC Power Receptacle Connect the included 5V DC power supply between this input and an open wall power socket DVI I Output This DVI I output port will support an analog or digital output display device A DVI to VGA adapter will be required when using a VGA capable display with this output port
5. the mirrored outputs two CAT 5 CAT 5e or CAT 6 cables will be required for full video audio and RS 232 support The CAT5 4000 receiver units need to be configured for use on either channel 1 dual outputs or for use on channels 2 and 3 There is a DIP Dual In line Package switch bank located on the underside of the CAT5 4000 receiver that will set the unit for proper operation for either channel 1 both outputs or for channels 2 or 3 Please see page 14 for details on how to change these DIP switches FEATURES Features e Both analog and digital video signals are supported through the use of DVI I inputs e DVI video is transmitted digitally for zero signal loss e Supports resolutions up to 1080p 2K and 1920 x 1200 Supports DDWG standard for DVI compliant monitors e Analog audio extension For channel 1 only e RS 232 serial communications extension for all channels e Usesindustry standard CAT5 CAT6 cable e Extends VGA up to 330 feet 100m with RS 232 e Extends DVI up to 130 feet 40m with RS 232 e DVI Video EQ enhancement controls brightness sharpness Package Includes 1 CAT5 4000 Extender Sender Unit 3 6 Foot DVI D Cable M M 3 6 Foot VGA to DVI A Cable M M 4 6 Foot DB 9 RS 232 Cable M F 1 6 Foot 3 5mm Stereo Mini Jack Audio Cable M M 2 5V DC Power Supply 1 User s Manual SENDER PANEL LAYOUT Front Panel Back Panel SENDER PANEL DESCRIPTIONS Powe
6. and the source devices second Once all connections have been properly made and power has been applied the green LED indicators above the VGA RJ 45 ports should be lit on the sender unit and all receiver units NOTE There are status indicators above each RJ 45 port Green indicators will be active on Sync Detect Red indicators will be active when the Analog Power is detected Adjusting the CAT5 4000 Extender Using an Analog VGA Source The CAT5 4000 was designed for plug and play installation However differences in CAT 5 cabling quality and skew rates may require the user to adjust the brightness and focus of the resulting video output If the output video is too blurry sharp or dark bright please use the instructions below to adjust the output quality 1 Locate the Brightness Br and Focus Fo Trim Pots on the front panel of the CAT5 4000 receiver 2 Insert a small flat head tool into the desired Trim Pot receptacle Turn the Trim Pot in either a clockwise or counter clockwise motion until the desired adjustment level is reached The Trim Pot has a limited range in both directions Please do not force the Trim Pot beyond the point at which it stops turning as this may break the Trim Pot 4 Remove the adjustment tool from the Trim Pot receptacle 11 CONNECTING THE CAT5 4000 EXTENDER DIGITAL DVI How to Connect the CAT5 4000 Extender Using an Digital DVI Source 1 Connect up to three digital DVI sources
7. ar on the displays at the remote locations OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE CAT5 4000 EXTENDER Maximum distance ratings VGA 1920x1200 60Hz is 330 feet e DVI 1920x1200 60Hz is 130 feet e DVI 1280x1024 60Hz is 300 feet VGA Supported resolutions 640 x 480 through 1920 x 1200 DVI Supported resolutions 640 x 480 through 1920 x 1080 The CAT5 4000 Extender can send only one video type either analog or digital from each input While the DVI I input can accept both types please ensure that only one type of signal is being used by using either a DVI A or DVI D cable The channel 1 video input will be mirrored to two separate outputs on the CAT5 4000 sender unit However two separate RS 232 inputs are provided and will accommodate an individual RS 232 device for each of the two mirrored video outputs Analog stereo audio connected via the 3 5mm mini stereo input jack will be transmitted through the mirrored outputs on channel 1 only Channels two and three do not support audio extension Channels two and three have individual RS 232 connections for use When analog video is used on channels two and three only a single CAT 5 CAT 5e or CAT 6 will be required for full video and RS 232 extension When digital video is being used two CAT 5 CAT 5e or CAT 6 cables will be required for full video and RS 232 support When analog or digital video is used on channel one this applies to either of
8. co 2 x RCA L R red white Audio Frequency response 20 Hz to 20 kHz 1 dB 0 196 LINK oss m RJ 45 Serial Communication Protocol RS 232C o Supports RX TX RTS protocols Max Bald encolado 115200kbps Power Consumption Each Unit coccccccooocccnncccnonnccnoconenononenenons 20 Watts max Power Supply Each Unit nn ne ee 5V DC External Dimensions 17 W x 1 75 Hx 5 5 D Dimensions Receiver 8 375 W x 1 75 Hx 4 25 D acq gro S e ine 1 Rack Spaces Shipping WV GIGI 8 Lbs 15
9. ibution and conversion technologies Gefen s reliable plug and play products supplement cross platform computer systems professional audio video environments and HDTV systems of all sizes with hard working solutions that are easy to implement and simple to operate The Gefen CAT5 4000 Extender The Gefen CAT5 4000 Extender is an exceptional solution for extending up to three individual analog or digital sources to up to four remote locations The first input is mirrored to two outputs RS 232 serial communication four individual inputs and stereo analog audio available for the mirrored outputs are also provided for extension How It Works The CAT5 4000 Extender employs DVI I inputs which will support both an analog and digital signals This will allow the user to connect VGA and DVI sources Connect the source devices to the CAT5 4000 sender unit using DVI A cables analog and DVI D cables digital Connect up to four RS 232 sources a single audio analog stereo to the CAT5 4000 sender unit Then using inexpensive and widely available CAT 5 CAT 5e or CAT 6 cables connect up to four CAT5 4000 receiver units to the CAT5 4000 sender unit at the remote locations Connect a display to the CAT5 4000 receiver at each location If using the RS 232 or analog stereo extension connect the corresponding equipment to each CAT5 4000 receiver Once all devices are connected and are receiving power a perfectly reproduced video signal should appe
10. led VGA Audio on the receiver unit 2 Connect the port labeled DVI RS 232 on the sender unit to the port labeled DVI RS 232 on the receiver unit This cable connection will not be necessary if RS 232 extension is not needed NOTE These outputs will mirror the single input on channel 1 When making connections from the sender to receiver please ensure that both CAT 5 cables for the outputs labeled Mon 1 are sent to the same location and both CAT 5 cables for Mon 2 are sent to the same location e Channels 2 and 3 1 Connect the port labeled VGA RS 232 on the sender unit to the port labeled VGA Audio on the receiver unit 2 When using analog VGA sources the RJ 45 port labeled DVI DDC will not need to be connected 5 Connect an analog VGA capable display to the DVI I output on the CAT5 4000 receiver unit A DVI to VGA cable adapter will be necessary to make this connection 10 CONNECTING ADJUSTING THE CAT5 4000 ANALOG VGA How to Connect the CAT5 4000 Extender Using an Analog VGA Source Continued from the previous page 6 Forreceivers connected to channel 1 connect a amplified stereo output device to the RCA analog stereo audio outputs on the receiver unit Channels 2 and 3 do not support audio extension 7 Connect a RS 232 device to the RS 232 connector on the CAT5 4000 receiver unit 8 Connect the included DC power supplies both the CAT5 4000 sender and receiver units 9 Power on all displays first
11. n is required a second CAT 5 cable must be connected using the channel 1 VGA RS 232 RJ 45 port Once a link between the sender and receiver unit has been established the green LED indicator located on these ports will become active Channel 1 DVI Input Connect an analog or digital source to this DVI I input port Depending on the input video signal type analog or digital a mirrored signal will be output to either the dual VGA or DVI RJ 45 ports 3 5mm Analog Stereo Audio Mini Jack Input Connect an analog stereo audio source to this input port The audio source connected to this input will be mirrored and output through both of the VGA Audio RJ 45 ports This audio source will not be output through any of the channel 2 and 3 RJ 45 output ports Channel 2 VGA RS 232 and DVI DDC RJ 45 Ports These RJ 45 ports connect the CAT5 4000 sender to a CAT5 4000 receiver unit using CAT 5 CAT 5e or CAT 6 cabling When the input source is analog the VGA RS 232 port is used When the input source is digital the DVI DDC port is used If RS 232 is required when using a digital input source use both RJ 45 ports Channel 2 DVI Input Connect an analog or digital source to this DVI I input port 9 9 10 11 SENDER PANEL DESCRIPTIONS Channel 3 VGA RS 232 DVI DDC RJ 45 Ports These RJ 45 ports connect the CAT5 4000 sender to a CAT5 4000 receiver unit using CAT 5 CAT 5e or CAT 6 cabling When the input source is analog the VGA RS 232
12. r LED Indicator This LED will become active once the included 5V DC power supply is properly connected between the unit and an open wall power socket RS 232 Serial Communication Input 1 4 These inputs will support RS 232 serial communications devices Only pins 2 RX 3 TX and ground 5 are supported Four inputs are provided The CAT5 4000 receiver units must be configured for RS 232 operation for either channel 1 both outputs or for channels 2 and 3 Please see page 14 Channel 1 VGA and Audio RJ 45 Port 1 2 When the input video source is analog these RJ 45 ports connect the CAT5 4000 sender to a CAT5 4000 receiver unit using CAT 5 CAT 5e or CAT 6 cabling Analog video and audio are transmitted through this connector Two ports are provided for mirrored video output of the channel 1 source to two separate locations If RS 232 extension is required a second CAT 5 cable must be connected using the channel 1 DVI RS 232 RJ 45 port Once a link between the sender and receiver unit has been established the green LED indicator located on these ports will become active Channel 1 DVI and RS 232 RJ 45 Port 1 2 When the input video source is digital these RJ 45 ports connect the CAT5 4000 sender to a CAT5 4000 receiver unit using CAT 5 CAT 5e or CAT 6 cabling Digital video and RS 232 are transmitted through this connector Two ports are provided for mirrored video output of the channel 1 source to two separate locations If audio extensio
13. r either channel 1 both outputs or for zen 2 and 3 Please see page 14 CONNECTING THE CAT5 4000 EXTENDER ANALOG VGA How to Connect the CAT5 4000 Extender Using an Analog VGA Source 1 Connect up to three analog VGA sources to the DVI I inputs on the CAT5 4000 sender unit VGA to DVI A cables adapters will be necessary to make these connections 3 VGA to DVI A cables are supplied 2 Connect an analog stereo audio source to the 3 5mm stereo audio mini jack port on the CAT5 4000 sender unit 3 Connect up to four RS 232 source devices to the RS 232 input ports on the CAT5 4000 sender unit NOTE Only pins 2 RX 3 TX and ground 5 are supported for RS 232 serial communication Although there are two mirrored video outputs for channel 1 there are 2 separate RS 232 connectors available for individual extension RS 232 1 corresponds to the Mon 1 output and RS 232 2 corresponds to the Mon 2 output To enable the RS 232 on channel 1 s dual RS 232 ports the CAT5 4000 receiver must be configured properly Please see page 14 for instructions on how to do this 4 Using CAT 5 CAT 5e or CAT 6 cables connect the CAT5 4000 receiver units to the sender unit Up to 4 receiver units can be used Please use the specific instructions below for connecting channels 1 through 3 1 2 mirrored outputs are available These are labeled Mon 1 and Mon 2 1 Connect the port labeled VGA Audio on the sender unit to the port labe
14. r units must be configured for use on either channel 1 on channels 2 and By default the CAT5 4000 units are configured to work on channels 2 and 3 To enable the RS 232 transmission for channel 1 a DIP Dual In line Package switch must be enabled This DIP switch is located on the underside of the CAT5 4000 receiver unit beneath a piece of metallic colored tape When using the CAT5 4000 receiver unit for the dual outputs on channel 1 please use the instructions below to enable the proper RS 232 transmission between the sender and receiver units Enable RS 232 DDC and HPD for channels 2 and 3 Default Enable RS 232 for both ports on channel 1 1 Locate the DIP switches on the underside of the CAT5 4000 sender unit The DIP switches will be covered by a small piece of metallic tape 2 Using a small pointed tool such as a pin flip the switch to the desired position 14 SPECIFICATIONS Analog Video Amplifier Bandwidth 2 350 MHz Digital Video Amplifier Bandwidth 2 2 165 MHz VGA Video Input Output Connectors DVI I 29 pin female VGA Video Frequency Ranges 15 70 KHz Horizontal 30 75 Hz Vertical VGA DDC signal 0 75V p p TTL DVI Video Input Output Connectors DVI I 29 pin female WIES ep T 5V p p TTL Audio NER 3 5mm female mini phone jack stereo eeu e as
15. t on channel 1 When making connections from the sender to receiver please ensure that both CAT 5 cables for the outputs labeled Mon 1 are sent to the same location and both CAT 5 cables for Mon 2 are sent to the same location e Channels 2 and 3 1 Connect the port labeled DVI DDC on the sender unit to the port labeled DVI RS 232 on the receiver unit 2 When using digital DVI sources the RJ 45 port labeled VGA RS 232 will need to be connected to the port labeled VGA Audio on the receiver unit This cable is not necessary if RS 232 extension is not required 5 Connect an digital DVI capable display to the DVI I output on the CAT5 4000 receiver unit DVI D cables should be used to ensure that digital video is being transmitted 12 CONNECTING ADJUSTING THE CAT5 4000 DIGITAL DVI How to Connect the CAT5 4000 Extender Using an Analog VGA Source Continued from the previous page 6 Forreceivers connected to channel 1 connect a amplified stereo output device to the RCA analog stereo audio outputs on the receiver unit Channels 2 and 3 do not support audio extension Connect a RS 232 device to the RS 232 connector on the CAT5 4000 receiver unit 7 Connect the included 5V DC power supplies both the CAT5 4000 sender and receiver units 8 Power on all displays first and the source devices second Once all connections have been properly made and power has been applied the green LED indicators above the DVI RJ 45 ports should
16. to the DVI I inputs on the CAT5 4000 sender unit DVI D cables should be used to ensure that digital video is being transmitted 2 Connect an analog stereo audio source to the 3 5mm stereo audio mini jack port on the CAT5 4000 sender unit Connect up to four RS 232 source devices to the RS 232 input ports on the CAT5 4000 sender unit NOTE Only pins 2 RX 3 TX and ground 5 are supported for RS 232 serial communication Although there are two mirrored video outputs for channel 1 there are 2 separate RS 232 connectors available for individual extension RS 232 1 corresponds to the Mon 1 output and RS 232 2 corresponds to the Mon 2 output To enable the RS 232 on channel 1 s dual RS 232 ports the CAT5 4000 receiver must be configured properly Please see page 14 for instructions on how to do this 4 Using CAT 5 CAT 5e or CAT 6 cables connect the CAT5 4000 receiver units to the sender unit Up to 4 receiver units can be used Please use the specific instructions below for connecting channels 1 through 3 Channel 1 2 mirrored outputs are available These are labeled Mon 1 and Mon 2 1 Connect the port labeled DVI RS 232 on the sender unit to the port labeled DVARS 232 on the receiver unit 2 Connect the port labeled VGA Audio on the sender unit to the port labeled VGA Audio on the receiver unit This cable connection will not be necessary if audio extension is not needed NOTE These outputs will mirror the single inpu
Download Pdf Manuals
Related Search