Edimax ES-5800D+ network switch
Contents
1. Gigabit Smart Switch 8 Ports 1000 100 10Mbps ES 5800D ES 5800R User s Manual lt O 7 2 D FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits of a Class A computing devices pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications If you suspect this product is causing interference turn your computer on and off while your radio or TV is showing interference If the interference disappears then when you turn the computer off and reappears then you turn the computer on something in the computer is causing interference You can try to correct the interference by one or more of the following measures 1 Reorient relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected 4 Ensure that all expansion slots on the back or side of the computer are covered Also ensure that all metal retaining brackets are tightly attached to the computer Content 1 Introduction sieste 3 2 Features amp Specifications ses 4 3 Package Contents 6 4 Hardware Des2. TEEE802 3x for full duplex Advance configuration functions VLAN setting Port based VLAN up to 8 groups Trunking Up to 2 trunking groups Priority Queuing CoS setting Port Mirroring Auto negotiation All ports Auto MDI MDIX function All ports System LED indication Power Port LED indication FULL COL Full duplex Collision Speed 10 100 1000Mbps LNK ACT Link Activity Operation Temperature 50 131 F 10 55 C Operation Humidity 10 95 Non condensing Power 100 240V AC full range internal power supply Emission FCC Class A CE C Tick 3 Package Contents Packing list Check the contents of your package for following parts One Gigabit Switch One User s manual One Power cord One RS 232 Cable If any of the items are missing or damaged please contact your local dealer 8 Port Gigabit Smart Switch 1000 100 10Mbps 00000000 Fulcd 4 Hardware Description This section describes the hardware features of this Gigabit Smart Switch For easier management and control of the switch familiarize yourself with its display indicators and ports All LEDs are located on the front panel of the switch They serve the purpose of monitoring the operation and performance of the switch at a glance LED indicators OO Ful Co 1000M Ydlow 100M Green 10M OFF OO LNK ACT FULL ON EULGOL COL Blink 1000M Yellow SPEED 100M Green 10M OFF LNK ON LNK ACT Q ACT Blink Operating Env
3. can reduce congestion and prevent packet loss In addition all the ports support the MDI MDI X auto detect function That is to say you can connect any device including PC Switch Hub to a port of this switch using a regular cable The RJ 45 port will auto detect and auto switch to the correct MDI MDI X mode do not need to use a specific uplink port or cross over cable 2 Features amp Specifications Features Complies with the IEEE802 3 Ethernet IEEE802 3u Fast Ethernet and IEEE 802 3ab Gigabit Ethernet Standards gigabit over copper Provides Store and Forward architecture and full wire speed filtering and forwarding rate Provides eight 10 100 1000Mbps Gigabit switching ports RJ 45 connector All ports provide Auto Negotiation and Auto MDI MDI X functions Supports flow control Back pressure for Half duplex and IEEE 802 3x for Full duplex mode Supports Port based VLAN up to 8 groups Supports QOS IEEE 802 1p 4 Priority queues per port Supports Port Mirroring Supports Console configuration Desktop 11 compact size designed Rackmount 19 rackmount size designed Specifications Standards IEEE802 3 10BaseT IEEE802 3u 100BaseTX and IEEE802 3ab 1000BaseT copper over Ethernet Total Ports 8 10 100 1000Mbps auto sensing Fast Ethernet Gigabit Ethernet ports Media Interface RJ 45 Forwarding Method Store and Forward MAC Address 8K Buffer Memory 256KBytes Flow control Back pressure for half duplex and
4. connected to the switch and the network device 2 Make sure the UTP cables comply with EIA TIA 568 and Category 5 specification 3 Collision LED flashes constantly 1 Remove all the network cables connect the cables back one by one to isolate the source of the collision 2 Check the network cable inferior cable quality will result in excessive collisions and packet errors Contact your dealer if problems persist 21
5. Plug the power cable into the internal three pronged power plug and connect it to an electrical outlet 5 Advance Smart Function Setting This switch provides advance features which offers you more flexibility in setting up your network The following section explains how to set up the VLAN Trunking Speed Port Mirror Full Half duplex and QoS modes Before using advance Configuration Connect to PC Attach a RS 232 serial cable 9 pin male connector to the female connector on the switch Plug the other side of this cable to your PC Using Hyper Terminal to connect to Switch In MS Windows launch Hyper Terminal create a new connection and follow these steps 1 Open the HyperTerminal application 2 In Windows select run from the start menu and choose the application 3 From the HyperTerminal menu double click the icon and create a new name on the next window such as Gigabit Smart Switch Mcoten cond peus 4 Adjust the setting of the communication port 4 1 Select the using by connect interface such as COM1 COM2 4 2 Select the Bits per second at 9600 4 3 Set the flow control value as None Connect To COM1 Properties 10 5 1 Login Page Once you have powered on the swtich it will boot up and enter the initial system screen as shown If this is your first time to log into the configuration program then the default user name is admin with passwo
6. able Enable Disable lt 1 gt Port Status lt 5 gt Trunk Config lt TAB gt Next Item lt 2 gt Port Config lt 6 gt Misc Config lt BACKSPACE gt Back lt 3 gt Mirror Config lt Ctrl D gt Set Default lt ENTER gt Toggle lt 4 gt VLAN Config lt Ctrl Q gt Save lt Ctrl P gt Password Connected 0 03 21 lansrw f cosni ECROL CAPS NUM Capture Print echo Press lt 2 gt to set up the Port configuration In this screen you can set up the port speed enable or disable the flow control function and set up the priority queues 1 In the Speed Dpx column it has six kinds of speed modes By pressing lt Enter gt you can choose AUTO 1000F 100F 100H 10F or 10H F and H represent Full duplex and Half duplex respectively to set the speed mode of the port 2 In the second column FlowControl you can press lt Enter gt to enable or disable the flow control function 3 At the last column you can set up the Priority queues of each port It provides four classes of service class O low class 1 normal class 2 high and class 3 very high 14 5 5 Mirror Port Configuration Gigabit Smart Switch HyperTerminal 5 x File Edit View Call Transfer Help D ols ols l 86 switch Console Program Mirror Config Port Mirroring Enable Monitored Port 3 Snooping Port 1 Monitored Pkts MEZE EOE lt 1 gt Port Status lt 5 gt Trunk Config lt TAB gt Next Item lt 2 gt Port C
7. cription 7 5 Advance Smart Function Setting 9 5 1 Login Pages 11 5 2 Top Screenvssicssssessissssssccssosserces 12 5 3 Port StatUsS ssssssssssssssssosssesssss 13 5 4 Port Configuration 14 5 5 Mirror Port Configuration 15 5 6 VLAN Configuration 16 5 7 Trunk Configuration 17 5 8 MISC Configuration 18 5 9 Set Password 19 6 Troubleshooting ss 21 1 Introduction Congratulations on your purchase of this eight ports Gigabit Smart Switch This high performance Gigabit switch provides eight 1000 100 10Mbps Gigabit Ports to allow simultaneous transmission of multiple packets via an internal high speed data channel The built in console interface can be used to configure the switch s settings for priority queuing VLAN Trunking Port Monitoring and Port speed This Gigabit switch utilizes store and forward switching architecture that filters and forwards data after the complete data packet is received and examined to be free of errors The front panel of this switch provides LEDs for easy recognition of the switch operation status and for troubleshooting All the Gigabit ports support both Full and Half duplex which are able to provide up to 2000Mbps of bandwidth to the connected devices with auto negotiation providing the capability to connect to 1000 100 10Mbps network devices It also supports backpressure and IEEE 802 3x advanced flow control capabilities that
8. gt Back lt 3 gt Mirror Config lt Ctrl D gt Set Default lt ENTER gt Toggle lt 4 gt VLAN Config lt Ctr1 Q gt Save lt Ctr1 P gt Password d Connected 0 05 24 ansiw focooe n 1 SCROLL CAPS NUM Capture Print echo 2 Port based VLAN is the simplest form of VLAN This switch allows you to create multiple VLANs each with its own broadcast domain and member ports In this screen you can choose the members of the VLAN group and then press enter to configure as in the following steps 1 Choose the VLAN group you want to set up and press Enter to enable it 2 Press lt Tab gt to move to the next column and choose the port you want to include For example we set up port 1 2 and port 3 in the same VLAN group as shown Note This unit can offer up to 8 VLAN groups and allows overlapping of several separate VLANs 16 5 7 Trunk Configuration Gigabit Smart Switch HyperTerminal 0 x File Edit View Call Transfer Help D ols x6 l 8G switch Console Program Trunk Config Trunk A P1 P2 Enable Trunk B P7 P8 Disable Balancing Method SORTIES ENT lt 1 gt Port Status lt 5 gt Trunk Config lt TAB gt Next Item lt 2 gt Port Config lt 6 gt Misc Config lt BACKSPACE gt Back lt 3 gt Mirror Config lt Ctrl D gt Set Default lt ENTER gt Toggle lt 4 gt VLAN Config lt Ctrl Q gt Save lt Ctr1 P gt Password This switch can setup two channel aggregation l
9. inks named Trunk A and Trunk B of to 2 ports each Trunk channel A is comprised from ports 1 and 2 while trunk channel B is comprised from ports 7 and 8 You can press lt ENTER gt to enable or disable this function Connected 0 06 48 gt ANSTW fosooe N t SCROLL CAPS NUM Capture Print echo There are three parameters of Balancing Method source port based method source address based method source and destination addresses based method 17 5 8 MISC Configuration In this screen you can set up the aging time You can select 300 600 900 1200 seconds or just disable it 18 5 9 Set Password Gigabit Smart Switch HyperT inal ols s13 af l Press lt Ctrl P gt you can change the username and password In this function you should fill in the old username and password then enter the new username new password and confirm it 19 Gigabit Smart Switch HyperTerminal After all the configurations were set up remember to store it with lt Ctrl Q gt The switch will save the configuration and exit the system You can restore all the configurations setting to the original values by pressing lt Ctrl D gt 20 6 Troubleshooting 1 Power LED is not lit Check if the power cord is properly connected to the power outlet and the switch 2 Link LED is not lit when connected to the network device 1 Check if the network cable is properly
10. ironment This switch must be installed and operated within the limits of the specified operating temperature and humidity see previous section on Specifications Do not place objects on top of the unit or obstruct any vents at the sides of the unit Do not position the unit near any heating source such as heaters radiators or direct exposure to sun Do not expose the unit to water and or moisture If necessary use a dehumidifier to reduce humidity Connecting to network devices 1 All ports of this switch support the Auto MDI MDI X function That is to say you can connect any device including PC Switch Hub to a port of this switch using a regular cable The RJ 45 port will auto detect and auto switch to the correct MDI MDI X mode do not need to connect to a specific uplink port or cross over cable Connect one end of the network cable to the RJ 45 port on the front panel and connect the other end of the network cable to the RJ 45 port on the network device Follow the same procedure to connect all the RJ 45 ports of the switch Maximum length using UTP cable between the switch and connected device is 100 meters 300ft Once the network cable is connected to both ends and the attached network device is powered on the LNK ACT LED should be lit Make sure the wiring is correct You need to use Category 3 4 5 cable for 10Mbps operation or Category 5 cable for 100Mbps and Gigabit 1000Mbps connections Connecting the power
11. onfig lt 6 gt Misc Config lt BACKSPACE gt Back lt 3 gt Mirror Config lt Ctrl D gt Set Default lt ENTER gt Toggle lt 4 gt VLAN Config lt Ctr1 Q gt Save lt Ctr1 P gt Password Connected 0 04 28 lanstw 9600 8 N 1 fecROLL CAPS NUM Capture Print echo The switch supports port monitoring This feature provides a complete network monitoring capability for each port A copy of egress Tx data and ingress Rx data of the monitored port is sent to their respective snooping ports The monitored port configuration function allows us to monitor the port traffic We can press lt Enter gt to enable or disable the function If you enable the port mirroring function you should set up the monitored port for example we set port 3 as monitored port as shown above and snooping port port 1 for example There are three kinds of packets you can choose to monitor Incoming Outgoing and Incoming amp Outgoing Press lt Enter gt to select the kind of packets you want to monitor 15 5 6 VLAN Configuration Gigabit Smart Switch HyperTerminal E 5 xj File Edit View Call Transfer Help D ols ols l 86 switch Console Program VLAN Config 12345678 Enable 1 yyy Enable 1 yufl Disable Disable Disable Disable Disable Disable lt 1 gt Port Status lt 5 gt Trunk Config lt TAB gt Next Item lt 2 gt Port Config lt 6 gt Misc Config lt BACKSPACE
12. rd admin After you have entered the correct user name and password you will have access to the system configuration program iixi File Edit View Call Transfer Help Bar als sls test mode chip is ok t eeprom is ok initial system Connected 0 00 21 Auto detect 9600 8 N 1 fscrou caps NUM Capture Print echo 4e Gigabit Smart Switch HyperTerminal x File Edit View Call Transfer Help Dle als alal l UserName admin Password xxxx_ Connected 0 09 31 lansrw 9600 8 N 1 Rou cars Num Capture Print echo 11 5 2 Top Screen Gigabit Smart Switch HyperTerminal E loj xj File Edt View Call Transfer Help 8G switch Console Program Port Config Speed Dpx FlowControl Priority 1 MA nable Disable Auto Enable Disable Auto Enable Disable Auto Enable Disable Auto Enable Disable Auto Enable Disable Enable Disable Enable Disable lt 1 gt Port Status lt 5 gt Trunk Config lt TAB gt Next Item lt 2 gt Port Config lt 6 gt Misc Config lt BACKSPACE gt Back lt 3 gt Mirror Config lt Ctr1 D gt Set Default lt ENTER gt Toggle lt 4 gt VLAN Config lt Ctr1 Q gt Save lt Ctr1 P gt Password i Connected 0 00 51 ANSIW fsooen t SCROLL Ars NUM Capture Print echo Once you log on to the Smart Switch s system configuration program with a console terminal emulator software e g Hyper Terminal the default Port Configura
13. tion screen seen above will appear With the system configuration program you can define system parameters manage and control the switch and all its ports or monitor network conditions Note Use the number key to select the function screen you want to set Press lt Tab gt to move between the items and then press lt Enter gt to change the value 1 Port Status Indicates the port s speed and link status 2 Port Configuration Sets up the speed and enables disables the flow control and priority function 3 Mirror Port Configuration Monitors traffic at the ports 4 VLAN Configuration Sets up the VLAN group of the switch 5 Trunk Configuration Sets up the trunking groups 6 MISC Configuration Sets up the aging time 12 5 3 Port Status Gigabit Smart Switch HyperTerminal Press lt 1 gt to display the port status The Speed Dpx parameter represents the speed 10 100 or 1000Mbps and half full duplex mode of the port For example 100 F represents the network is 100Mbps with full duplex mode If the network is connected the LinkStatus shows ON otherwise it shows OFF 13 5 4 Port Configuration Gigabit Smart Switch HyperTerminal x File Edit View Call Transfer Help D 613 08 l 8G switch Console Program Port Config Speed Dpx FlowControl Priority 1 100F isable Disable Auto Enable Class 0 Auto Enable Class 1 Auto Enable Class 2 Auto Enable Auto Enable Disable Enable Dis
Download Pdf Manuals
Related Search