Home
TE Connectivity MRJ21(180°) - MRJ21(180°), CMR
Contents
1. TE AMP NETCONNECT MRJ21 Instruction Sheet 408 10469 04 OCT 11 Rev A PAE Cable Assemblies emp L P Front Mating Shield Receptacle E Polarizing Key J i a Screw Marking y 2 Places Back of Patch Panel or Cassette Assembly Head of Jack Screw 2 Places Cable Jacket Key Label Figure 1 1 INTRODUCTION This instruction sheet provides proper handling and installation and removal guidelines for AMP NETCONNECT MRJ21 cable assemblies To obtain information on AMP NETCONNECT products call PRODUCT INFORMATION at the number at the bottom of this page or visit the AMP NETCONNECT website at www ampnetconnect com 2 PROPER HANDLING It is important to exercise the following proper handling procedures when transporting and installing cable ALWAYS pull cable off of a reel from the connector end marked UNWIND FROM THIS END DO NOT pull the cable from the wrong end otherwise the cable will tangle Take care to not drop or crush the connectors DO NOT hit the connector ends against any hard surface Dropping or hitting the connector against a hard surface may result in bending or breaking of the front mating shield Observe and implement proper minimum cable bend radius and pulling tension per TIA 568 AMP NETCONNECT logo is a trademark of TE Connectivity DO NOT attempt to connect a connector with a damaged front mating shield DO NOT attempt to repair a damaged fron
2. e fully loosened before pulling the plug and DO NOT attempt to remove the plug by force CAUTION 4 REPLACEMENT AND REPAIR MRJ21 cable assemblies are not repairable DO NOT use any defective or damaged components 5 REVISION SUMMARY Initial release of instruction sheet 2011 Tyco Electronics Corporation a TE Connectivity Ltd Company All Rights Reserved Trademark TE Connectivity TE connectivity logo and TE logo are trademarks Other logos product and or Company names may be trademarks of their respective owners TOOLING ASSISTANCE CENTER 1 800 722 1111 PRODUCT INFORMATION 1 800 522 6752 This controlled document is subject to change 1 of 1 For latest revision and Regional Customer Service visit our website at www te com LOC B
3. t mating shield 3 INSTALLATION AND REMOVAL GUIDELINES 3 1 Installation 1 Align the polarizing key of the plug with the polarizing key marked on the back of the patch panel or cassette assembly of the receptacle Refer to Figure 1 A label marked KEY attached to the plug indicates the location and orientation of the polarizing key Failure to observe location of the polarizing keys may result in improper wiring connection and initial electrical and communications start up testing DO NOT attempt to overcome the polarizing keys by force CAUTION 2 Insert the plug into the receptacle until it bottoms Ensure that the plug is fully seated into the receptacle before tightening the jack screws Failure to bottom the plug may result in stripping or cross threading of the jack screws CAUTION 3 Using a long thin small cross recessed tipped screwdriver turn each jack screw CLOCKWISE Tighten each screw to a maximum torque of 0 23 N m 2 Ibf in DO NOT use an automatic screwdriver To avoid cross threading or stripping of the jack screws or damage to the receptacle DO NOT over tighten the jack screws CAUTION 3 2 Removal Using a small cross recessed tipped screwdriver turn each jack screw of the plug COUNTERCLOCKWISE until it is loose then gently but firmly pull the plug away from the receptacle until it is released To avoid damage to the receptacle ensure that the jack screws ar
Download Pdf Manuals
Related Search
Related Contents
KOHLER K-14404-4A-SN Installation Guide MPP1700 Users Manual - Visionary Solutions Da-Lite Insta-Theater Plus 60" x 80", Video, Wide Power SoftWall Finishing Systems SW9729667010 Instructions / Assembly Service Manual Le Serment d`Hippocrate et les sources philosophiques de l`éthique OWNERS MANUAL - Blue Ridge Mountain Cookery 仏壇の表示に関する公正競争規約 OKI B4350 Laser Printer - Oki Data B4100-B4250 Copyright © All rights reserved.