Zalman Z9 Plus
Contents
1. When fastening the Tray Type A Bolts must be used Caution Attach Drive to Tray A 3 5 FDD Installation ZALMAN Z9 Z9 Plus B 3 5 HDD Installation When removing the front cover the power switch and extension cable are separated to prevent disconnection Be sure to connect them before insfalling the front cover Caution ZALMAN 29 29 Plus 7 3 5 HDD Installation 1 Installation of HDD Anti static rubber and Bolt 9 D Bolt HDD Anti static rubber The HDD can be installed in 2 different directions according to your desired Cable Management style A Type i B Type 2 HDD Installation Push into the 3 5 Bay until a click sound is heard ZALMAN Z9 Z9 Plus When transporting an assembled system please secure the HDD with Bolt E as shown above 3 HDD Removal When removing HDD pull the ZALMAN Z9 Z9 Plus 8 SSD Installation SSDs can be installed on the right side of case as shown in the diagram below 9 Cable Connecti2. 3 Front Panel Fan 120 140mm Replacement One 120mm Fan is pre installed ZALMAN
3. X The Tuning Side Panel left is only available on the Z9 Plus a ZALMAN Z9 Z9 Plus 5 Parts lt lt Cs User s Manual 200 Main Unit Stand Off x 5 A Bolt 6 32 6mm 11 B Bolt M3 5mm 17 PSU PCI M B FDD SSD C Bolt M3 6mm 12 D Bolt 6 32 4mm 20 5 25 Bay ODD 13 5 Bay HDD U E Bolt 6 32 6mm 5 HDD Anti static rubber x 20 13 5 HDD 13 5 Bay HDD Cable Tie 5 CPU 12V Extension Cable 1 ZALMAN o 29129 Plus 68 Installation 1 Side Panel Removal 2 PSU Installation Z9 Z9Plus When using the case in a dusty environment use Type B Type PSU independent cooling If the PSU s fan points downwards the PSU 8 cooling performance is enhanced Type B Case Air Circulation Type If the PSU s fan points inwards the PSU s cooling performance is enhanced ZALMAN 29 Z9 Plus 3 Motherboard Installation There are 4 Stand Offs preinstalled Please refer to the diagrams below for additional Stand Off positions based on motherboard type ATX Board m ATX Board ZALMAN Z9 Z9 Plus 4 VGA Card Installation 29 i u A Bolt 27 5 5 25 and 3 5 Drive Installation 1 Front Cover Removal TI og ZALMAN 29 29 Plus i md m 71
4. Cautionary Notes 1 Please read this manual thoroughly prior to installation 2 Before installing check the components and condition of the product and if any problem is found contact the retailer 3 Avoid inserting objects or hands into the system while it is in operation to prevent product damage and injuries 4 Check the manual when connecting cables Incorrect connections may cause short circuits leading to fire hazards 5 Do not block the front intake vent or the rear exhaust vent 6 Keep this unit away from heat sources direct sunlight water oil and humid environments and place the unit on a flat stable vibration free and well ventilated area 7 Do not clean the product surface with chemicals or wet cloth chemicals industrial brightener wax benzene alcohol paint thinner mosquito repellent aromatics lubricant detergent etc 8 Please wear gloves while handling this product to prevent injuries 9 Product design and specifications may be revised to improve quality and performance Disclaimer Zalman Tech Co Ltd is not responsible for any damages due to extemal causes including but not limited to improper use problems with electrical power accident neglect alteration repair improper installation or improper testing The diagrams used in this manual are based on model 79 Plus Installation for the 29 follows the exact installation procedure ZALMAN 29129 Plus 2 P
5. on 1 Power Button Cable Power Button Power LED Power Motherboard ZALMAN Z9 Z9 PI 2 Front Panel I O Port Cable Front Panel I O Port connection Front Panel I O Port Audio AD 1 11111 11111 11 11 HD Audio AC 97 USB 2 0 USB 2 0 Reset HDDLED Motherboard To connect USB 2 0 audio cables please refer to the motherboard manual When the polarities are reversed the LED s will not function Fan Control Temperature Display connection Fan Controller After connecting the 4 Pin Power cable connect Fans to Fan Connector Temperature Display After connecting 4 Pin Power locate temperature sensor in desired location The sensor is for the case s internal temperature readings Fan Controller Temperature Display PSU Power Fan Fan Temperature PSU Power Sensor ZALMAN o Z9 Z9 Plus 10 Optional Fan Installation and Replacement 1 Optional Side Panel Fan 120mm Installation The Z9 Plus comes with one 120mm Side Panel Fan pre installed 2 Top Panel Fan 120 140 mm Installation When installing fan press the Top Panel s eight Hook s towards each other to remove and install as shown in diagram below The Z9 Plus comes with one 120mm Fan pre installed ZALMAN Z9 29 Plus
6. roduct Details 1 Specifications Models Z9 Plus Z8 Type ATX Mid Tower Dimensions WxHxD 207 484 x 504mm 8 1 x 182 x 19 8 29 Plus 7 2 15 8 Ib Materials Plastic Steel Weight Color Black Motherboard Compatibility Standard ATX m ATX Power Supply Compatibility Standard ATX12V PCI AGP Compatibility Full Size 290mm 11 4 5 25 External Bay x 3 External Bay x 1 Internal Bay x 5 Drive Bays 5 253 512 5 1 3 1 Hot swap Card Solts 7 Slots Z8 Plus 120mm 140mm Fan Vent x 2 1 Fan included 1 optional 28 120mm 140mm Fan Vent 2 Fans optional Cooling component om of 140mm Fan ren 120mm 140mm Fan Vent x 1 Fan optional 120mm Fan Vent x2 s 23818 1 Fan included 1 optional 29 120mm Fan Vent 2 Fans optional 28 Plus Front Panel O Port n Headphones x 1 Mic x 1 USB 2 0 x 4 29 Z9 Z9 Plus 2 Product Information d Top Side left 3 Front Panel I O Ports Power Button Temperature Display L ic ___J 08820 A A 08820 Mic Headphones USB 2 0 Fan Controller Reset Button X Temperature and Fan Controller display are only available on the Z9 Plus ZALMAN 29 Z9 Plus 4 Exploded View
Download Pdf Manuals
Related Search