Dual MCP300GH car media receiver
Contents
1. Antenna Connector BLUE Remote Connect to amplifier or power antenna Insulate wire if not used BLACK Ground Connect to ground or directly to battery negative terminal RED Accessory 1 Connect to existing ignition circuit or switched 12 volt source 10 AMP AGC Fuse 12 2 FUSE When replacing the fuse YELLOW aiak make sure new fuse is the circuit or constant 12 volt source correct type and amperage Using an incorrect fuse could damage the radio The MDM300 uses one 10 amp Right Front Right Rear ae Gray Black Violet Black AGC fuse located in line Gray Violet Left Front Left Rear White Black Green Black White Dual MDM300 OPERATION Control Locations Receiver CD RECEIVER MARINE 5 501 1 Release 13 Preset 4 Random 2 Mute 14 Preset 3 Repeat 3 5 15 Preset 2 Intro 4 Scan Preset 1 Play Pause 5 Display 17 Local Distance 6 Audio Volume Knob Mono Stereo 7 Loudness Tune Track Up Eject Band 92. Note Seek and manual tuning functions are reversed if Seek Priority is set to SEEK 2 in the setup menu refer to page 7 for details on setting Seek Priority Press SCAN momentarily to listen to the next strongest station for 5 seconds Press SCAN again to cancel Press BAND to select between FM1 FM2 FM3 AM1 and AM2 bands Up to 18 FM stations and 12 AM stations can be stored To store a station select the desired band and station Press and hold the desired preset button 1 6 for more than 2 seconds When stored the preset number will appear in the display The station can be recalled anytime by pressing the corresponding preset button Press AMS for more than 2 seconds to automatically store all strongest stations in the current band After the six strongest stations are set a scan of each stored preset will begin Press AMS or TRACK gt to cancel Press AMS momentarily to scan preset stations for five seconds each To select a station during the scan press AMS again or press the corresponding preset button Press LOC to select between Local and Distance tuning Selecting LOCAL programs the unit to stop at only strong stations when seek tuning Press MONO to select Mono or Stereo operation Selecting MONO can improve listening in areas with a weak FM signal MDM300 OPERATION CD Player Operation Insert CD Eject CD Track Select Fast Forward Reverse Pause Intro Repeat Random CD R C
3. MDM300 OPERATION CD Player Operation MP3 WMA Files Playing an MP3 WMA CD Displaying Information Character Support Track Jump Intro Repeat Random When an MP3 WMA encoded disc is first inserted LOAD will appear in the display Depending the number of files and folders this may take several seconds 103 tag and file folder information will automatically be displayed during playback Press BAND to manually select and display the song information Maximum character display information e Track name 64 character maximum Directory name 64 character maximum e Song title 64 character maximum e Artist name 64 character maximum Album name 64 character maximum Song title artist name and album name will only be displayed if included with the MP3 WMA file When referring to MP3 WMA playback the following terms are synonymous e File name and track name Folder name and directory name Press 10 to skip ahead 10 tracks Press 10 to skip back 10 tracks Press INT to play the first 10 seconds of each track Press INT again to turn the Intro function off Press RPT to continuously repeats selected track Press RPT again to turn the Repeat function off Press RDM to play all tracks in random order Press RDM again to turn the Random function off MDM300 OPERATION CD Player Operation MP3 WMA Files Media Compatibility Playback Order Compatible Recording
4. Additional MP3 WMA Information Sampling Frequency Rates MP3 WMA Transfer Bit rates MP3 WMA MP3 Tag Display USB Device Compatibility USB SD Device Capacity Only MP3 files with filename extension mp3 can be played Only WMA files with filename extension wma can be played Do not attempt to play non MP3 WMA files with the MP3 WMA extension 8kHz 48kHz 8kHz 48kHz 8kbps 320kbps constant Variable bit rates 8kbps 384kbps constant Variable bit rates Note Some files may not play or be displayed correctly depending on sampling rates and bit rates ID3 tags Version 1 0 to 2 0 Note If an invalid 103 tag version is detected NO SUPPORT will scroll on the display Due to the differences of USB devices and SD Cards some devices may not be compatible USB devices and SD Cards must be mass storage class and formatted to the FAT or FAT32 file system in order to ensure compatibility USB SD Cards must be 32GB or smaller in capacity to be compatible MDM300 OPERATION Music Search MP3 WMA Files Time Search Press AMS until TIME SCH appears Turn the volume knob left right to choose the desired elapsed time in the current song Press AUDIO to begin playback from the displayed elapsed time Track Search Press AMS until SCH appears Turn the volume knob to choose the first digit in the track number After one second the first digit is saved Turn the volume knob to
5. Formats The following types of discs files are compatible e CD ROM ISO CD R CD RW e CD DA e MP3 data e WMA data The following types of discs files are not compatible e WMA files that are protected by DRM Digital Rights Management e WMA lossless format Discs recorded with Track At Once or packet writing MP3 PRO format MP3 playlists AAC protected AAC format e WAV format Playback sequence begins in the root folder Any empty folders or folders that do not include compatible files are skipped Depending on your software the playback order may vary 509660 level 1 1509660 level 2 e Yellow Book MODE 1 e Yellow Book MODE 2 FORM 1 e Multi session e Maximum folders and files 256 e Maximum folder levels 8 e MPEG 1 2 2 5 Audio Layer 3 1509660 standards e Maximum nested folder depth is 8 including the root folder Valid characters for folder file names are letters A Z all caps numbers 0 9 and _ underscore Some characters may not be displayed correctly depending on the character type This device can play back discs in Joliet Romeo and other standards that conform to 1509660 MP3 WMA written in the formats other than the above may not play and or their file names or folder names may not be displayed properly MDM300 OPERATION CD Player Operation MP3 WMA Files Additional MP3 WMA Information Sampling Frequency Rates MP3 WMA Tra
6. Media Compatibility Playback Order Playback Capacity MDM300 OPERATION SD Card USB Operation Maximum character display information e Track name 64 character maximum e Directory name 64 character maximum e Song title 64 character maximum e Artist name 64 character maximum Album name 64 character maximum Song title artist name and album name will only be displayed if included with the MP3 WMA file The following types of files are compatible e MP3 data e WMA data The following types of files are not compatible e WMA files that are protected by DRM Digital Rights Management e WMA lossless format e Discs recorded with Track At Once or packet writing MP3 PRO format MP3 playlists AAC protected AAC M4A format e WAV format Playback sequence begins in the root folder Any empty folders or folders that do not include compatible files are skipped Depending on your software the playback order may vary e Maximum number of files 2000 e Maximum number of folders 500 plus the root directory e Maximum number of files in each folder and root 2000 e Maximum number of folder levels sub folders 8 7 levels plus the root Note If the number of files folders exceeds the maximum outlined above the additional files folders will be ignored Note Devices that exceed the maximum number of files or folders may not function properly MDM300 OPERATION SD Card USB Operation
7. low volumes Press DISP to show the clock During playback of MP3 WMA files ID3 tag information elapsed time track number file folder names will automatically alternate on the display Press RESET upon initial installation or if abnormal operation occurs Reset button is located behind the front panel With the unit on press and hold DISP until the clock begins to flash then release Turn the volume knob to the right to adjust the hours or to the left to adjust the minutes The clock will display 12 hour AM PM time in USA frequency spacing mode PM 10 00 In European frequency spacing mode the clock will display 24 hour time 22 00 Press and hold the volume knob for more than 3 seconds to access the setup menu Press volume knob momentarily to select between the menu functions and rotate the volume knob left right to adjust or activate the desired function MDM300 OPERATION General Operation Setup Menu Toggles between the following equalization options OFF POP ROCK CLASS and FLAT Beep BEEP OFF Disables the confirmation beep Confirmation BEEP ON Enables the confirmation beep Seek Priority SEEK 1 Enables seek tuning priority i SEEK 2 Enables manual tuning priority Programs unit to always turn on at the last volume selected Programmable VOL LAST before it was turned off Turn On Volume VOL ADJ Programs unit to always turn on at a specific volume Any volume level 1 47 can be selected Prog
8. 4 ne SSS J w MDM300 CD RECEIVER MARINE eS na SS eee 2 t MDM300 INSTALLATION OWNER S MANUAL CD Marine Receiver TM DIGITAL AUDIO MDM300 INSTALLATION Preparation Please read entire manual before installation Before You Start e Disconnect negative battery terminal Consult a qualified technician for instructions e Avoid installing the unit where it would be subject to high temperatures or where it would be subject to dust dirt or excessive vibration Getting Started e Remove 2 transit screws located on top of the unit Insert the supplied keys into the slots as shown and slide the unit out of the mounting sleeve Install mounting sleeve into opening bending tabs to secure e Connect wiring harness and antenna Consult a qualified technician if you are unsure e Test for correct operation and slide into the mounting sleeve to secure e Snap trim ring into place Mounting sleeve opening dimensions 7 11 64 x 2 3 32 182 mm x 53 mm REMOVAL KEYS MOUNTING SLEEVE TYPICAL MOUNTING METHOD MDM300 INSTALLATION Wiring Diagram Rear RCA Output Right Red Left White aja ajm E ajm
9. D RW Compatibility With the label facing up insert a standard size CD into the CD slot The CD will automatically begin playback Press EJECT to eject the CD The unit will change to previous mode of operation If the disc is not removed within 10 seconds the unit will reload the disc The unit does not have to be turned on to eject CD Press TRACK BB to skip to the beginning of the next track Press TRACK 4 4 to return to the beginning of the current track Pressing TRACK lt 4 4 again skips to the beginning of the previous track Press and hold TRACK or TRACK 4 4 to fast forward or reverse a track Press gt to temporarily stop CD playback Press gt again to resume playback Press INT to play the first 10 seconds of each track Press INT again to turn the Intro function off Press RPT to continuously repeats selected track Press RPT again to turn the Repeat function off Press RDM to play all tracks in random order Press RDM again to turn the Random function off Some CD Rs and CD RWs may be incompatible with this unit depending on media type and recording method In addition the following CDs may be incompatible with this unit CDs exposed to extreme temperatures or direct sunlight for extended periods of time CDs recorded in which a recording session failed or a re recording was attempted and or encrypted or copy protected CDs which do not conform to the audio CD DA red book recording standard
10. USB Input 21 Mode Auxiliary Input 22 Power 1 Preset 6 10 Skip 23 Tune Track Down 12 Preset 5 10 Skip MDM300 OPERATION Dual Control Locations Remote 1 Power Mute 2 Volume Up 1 Preset 6 10 G Select 12 Preset 5 10 4 Tune Track Up 13 Preset 4 Random 5 Volume Down 14 Preset 2 Intro 6 Scan 15 Preset 1 Play Pause 7 Display Mode Loudness 17 Band 9 Preset 3 Repeat Tune Track Down MDM300 OPERATION General Operation Faceplate Removal Power On Off Mode Auxiliary Input Volume Loudness Display Reset Set the Clock 12 24 hour Clock Setup Menu Press RELEASE and pull away from the left side to remove To re install insert right side of faceplate first then push left side to secure Press other button except EJECT to turn the unit on Press to turn the unit off Press MODE to select between AM FM CD player auxiliary USB and SD card Modes of operation are shown in the display NOTE CD SD and USB modes will not appear unless a CD SD Card or USB device is inserted The MDM300 a 3 5 mm auxiliary input port on the front panel of the unit for connecting an audio device MP3 player etc Press MODE to select auxiliary input mode Adjust volume using volume knob 0 47 Press LOUD to activate the Loudness function Activating Loudness will enhance the bass and treble frequencies when listening to music at
11. ate of the original purchase Dual Electronics Corp agrees at our option during the warranty period to repair any defect in material or workmanship or to furnish an equal new renewed or comparable product whichever is deemed necessary in exchange without charges subject to verification of the defect or malfunction and proof of the date of purchase Subsequent replacement products are warranted for the balance of the original warranty period Who is covered This warranty is extended to the original retail purchaser for products purchased from an authorized Dual dealer and used in the U S A What is covered This warranty covers all defects in material and workmanship in this product The following are not covered software installation removal costs damage resulting from accident misuse abuse neglect product modification improper installation incorrect line voltage unauthorized repair or failure to follow instructions supplied with the product or damage occurring during return shipment of the product Specific license conditions and copyright notices for the software can be found via www dualav com What to do 1 Before you call for service check the troubleshooting guide in your owner s manual A slight adjustment of any custom controls may save you a service call N If you require service during the warranty period you must carefully pack the product preferably in the original package and shi
12. choose the second digit repeating the process until the desired track number is shown Press AUDIO to begin playback for the displayed track Example To choose track 100 press AMS until SCH appears then turn the volume knob until 1 appears Wait one second then choose 0 Wait one second then choose 0 Press AUDIO to begin playing track number 100 File Search Press AMS until FILE SCH appears Turn the volume knob to cycle through all the songs on the device The songs will be listed in the order that they are copied to the device Press AUDIO to begin playback when the desired song is displayed Character Search Press AMS until CHAR SCH appears Turn the volume knob to choose the first character in the song name Once the first character is chosen wait one second then press AUDIO to search for all songs that begin with that letter A list of songs with names beginning with the chosen letter will be available Turn the volume knob to cycle through these songs and press AUDIO to begin playback Example Choose then press AUDIO to display all the songs that have names beginning with B MDM300 OPERATION Limited One Year Warranty This warranty gives you specific legal rights You may also have other rights which vary from state to state Dual Electronics Corp warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the d
13. ires touching Insulate all bare speaker wires but no sound each other or touching chassis ground from each other and chassis ground Yellow or red wire touching chassis 7 Unit blows fuses Speaker wires touching chassis ground Check for pinched wire Use fuse with correct rating Unit is not mounted correctly or Check mounting sleeve and Excessive skipping backstrap is not secure backstrap support ive skippi 2 Physical defect in media CD CD R Check media for seratehes CD RW ERR FILE appears ar display Focus error disc is in upside down Press eject or RESET The WMA file is copy protected by DRM Write disc using WMA files that Digital Rights Management are not copy protected NO FILE appears No playable MP3 WMA files found on Check the device for valid on display the device MP3 WMA files CD mechanism position out of Press EJECT to reset CD Unit will not accept alignment mechanism position a disc zi emove 2 transit screws CD transit screws still in place located on top of the unit NO SUPPORT appears ee 22224 Version 1 0 to 2 0 103 tags on display An invalid 103 tag version is present MDM300 OPERATION Specifications CD Player Frequency response 20Hz 20kHz Channel separation 1kHz gt 60dB D A converter 1 Bit FM Tuner Tuning range 87 5MHz 107 9MHz Usable sensitivity 8 5dBf 50dB quieting sensitivity 10dBf Stereo separation 1kHz gt 30dB Frequency response 30H
14. m SD Card insert the card horizontally with the label facing up into the SD Card slot located behind the front panel When a USB device is first connected LOAD will appear in the display and playback will begin momentarily To begin playing music from an SD Card press MODE to select SD mode and begin playback Depending on the number of files and folders it may take several seconds for the device to begin playing If no valid MP3 WMA files are detected NO FILE will be displayed and the last mode will be resumed Press TRACK B gt B to skip to the beginning of the next track Press TRACK lt lt to return to the beginning of the current track Pressing TRACK lt lt again skips to the beginning of the previous track Press hold TRACK gt or TRACK 4 4 to fast forward or reverse a track Press P Ill to temporarily stop playback Press gt again to resume playback ID3 tag and file folder information will automatically be displayed during playback Press BAND to manually select and display the song information Press 10 to skip ahead 10 tracks Press 10 to skip back 10 tracks Press INT to play the first 10 seconds of each track Press INT again to turn the Intro function off Press RPT to continuously repeats selected track Press RPT again to turn the Repeat function off Press RDM to play all tracks in random order Press RDM again to turn the Random function off Character Support
15. nsfer Bit rates MP3 WMA MP3 Tag Display Recommended Settings When playing a disc recorded with regular audio files CD DA WAV and MP3 WMA files the unit will play the MP3 WMA files only Only MP3 files with filename extension mp3 can be played Only WMA files with filename extension wma can be played Do not attempt to play discs which contain non MP3 WMA files with the MP3 WMA extension 8kHz 48kHz 8kHz 48kHz 8kbps 320kbps constant Variable bit rates 8kbps 384kbps constant Variable bit rates Note Some files may not play or be displayed correctly depending on sampling rates and bit rates ID3 tags Version 1 0 to 2 0 This model will not display ID3 Version 2 0 or greater tags For best results use the following settings when burning an MP3 disc 128kbps or higher constant bit rate 44 1kHz or higher sampling frequency For best results use the following settings when burning a WMA disc 64kbps or higher constant bit rate 32kHz or higher sampling frequency MDM300 OPERATION SD Card USB Operation Connecting a USB Device sold separately Inserting an SD Card sold separately Playing Music Track Select Fast Forward and Reverse Pause Displaying Information Track Jump Intro Repeat Random To play MP3 WMA files from most USB mass storage devices line up the USB connector and insert the USB device into the USB port To play MP3 WMA files fro
16. ommunications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e or relocate the receiving antenna e the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e the dealer an experienced radio TV technician for help 21 Notes 22 Dual MDM300 OPERATION MDM300 OPERATION Dual Notes 23 Dual Electronics Corp Toll Free 1 866 382 5476 The SD logo is a trademark of the SD Card Association Other trademarks and trade names are those of their respective owners www dualav com 2012 Dual Electronics Corp All rights reserved 5 1111 01
17. p it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center Please describe your problem writing and include your name a return UPS shipping address 0 Box not acceptable and a daytime phone number with your shipment 4 For more information and for the location of the nearest authorized service center please contact us by one of the following methods e Call us toll free at 1 866 382 5476 E mail us at cs dualav com Exclusion of Certain Damages This warranty is exclusive and in lieu of any and all other warranties expressed or implied including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation liability right claim or remedy in contract or tort whether or not arising from the company s negligence actual or imputed No person or representative is authorized to assume for the company any other liability in connection with the sale of this product In no event shall the company be liable for indirect incidental or consequential damages MDM300 OPERATION Troubleshooting Yellow wire not connected or incorrect Check connections for proper Unit will not turn on kalbet or voltage 11 16VDC no power Black wire not connected Check connection to ground Replace fuse Speaker wires not connected Check connections at speakers Unit has power One or more speaker w
18. rams the unit to USA tuner spacing e tuner FREQ USA 200kHz for FM and 10kHz for AM requency Spacin Programs the unit to European tuner spacing FREQEUR 50kHz for and 9kHz for Tuner Frequency Spacing is only selectable from Tuner mode MDM300 OPERATION General Operation Audio Press AUDIO momentarily to select between Bass Treble Balance and Fader BASS gt TREBLE gt BALANCE gt FADER J Bass Press AUDIO until BAS appears then rotate volume knob left right to adjust 7 minimum 7 maximum Treble Press AUDIO until TRE appears then rotate volume knob left right to adjust 7 minimum 7 maximum Balance Press AUDIO until BAL appears then rotate volume knob left right to adjust BAL 10L BAL 10R BAL EVEN represents equal balance Fader Press AUDIO until FAD appears then rotate volume knob left right to adjust FAD 10R FAD 10F FAD EVEN represents equal fader Seek Tuning Manual Tuning Scan Tuning Band Storing and Recalling Station Presets Automatically Store Stations Preset Scan Distance Tuning Stereo Mono MDM300 OPERATION AM FM Tuner Operation Press TUNE 4 4 or TUNE momentarily to seek to the next strong station Press and hold TUNE 4 4 TUNE gt until MANUAL appears then press TUNE 4 4 or TUNE momentarily to change radio frequency up or down one step at a time Press and hold to advance quickly
19. z 13kHz AM Tuner Tuning range 530kHz 1710kHz Usable sensitivity lt 42dBu Frequency response 30Hz 2 2kHz General Speaker output impedance 4 8 ohms Line output voltage 2 Volts RMS Fuse 10 amp AGC Dimensions 7 x 7 x 2 178 x 178 x 50 mm Design and specifications subject to change without notice CEA 2006 Power Standard Specifications reference 14 4VDC 0 2V 20Hz 20kHz Power Output 18 Watts RMS x 4 channels at 4 ohms and lt 1 THD N Signal to Noise Ratio 70dBA reference 1 watt into 4 ohms 20 MDM300 OPERATION FCC Compliance This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio c
Download Pdf Manuals
Related Search