Moxa PTC-101-M-LC-HV network media converter
Contents
1. 1 2in O O D z 2 jS olf T llo Ea PTC 101 M SCHV p y s LJ z z ie 22 gt 66 65 mm 2 62 in 33 34mm 1 34 in 51 6 mm 2 03 in Front View Rear View Panel Mounting Kit Optional Wiring Requirements ATTENTION Safety First Be sure to disconnect the power cord before installing and or wiring your Moxa Industrial Media Converter ATTENTION Safety First Calculate the maximum possible current in each power wire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat causing serious damage to your equipment 4 You should also pay attention to the following points e Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point NOTE Do not run signal or communications wiring and power wiring in the same wire conduit To avoid interference wires with different signal characteristics should be routed separately You can use the type of signal transmitted through a wire to determine which wires should be kept separate The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together Keep input wiring and output wiring separated It is strongly advised tha2. E E les N61000 4 8 2001 03 Level 5 N61000 4 11 2004 03 Criteria B TEC 61850 3 IEEE 1613 EN50155 EN50121 4 5 years Details See www moxa com warranty Technical Support Contact Information Moxa Americas Toll free 1 888 669 2872 Tel 1 714 528 6777 Fax 1 714 528 6778 Moxa Europe www moxa com support Moxa China Shanghai office Toll free 800 820 5036 Tel 86 21 5258 9955 Fax 86 10 6872 3958 Moxa Asia Pacific Tel 49 89 3 70 03 99 0 Tel 886 2 8919 1230 Fax 49 89 3 70 03 99 99 Fax 886 2 8919 1231 P ia EA
3. auto MDI MDI X e Multi mode single mode with SC or ST or LC fiber connector available e Supports Link Fault Pass Through e Power failure by relay output LV model only Redundant dual VDC power inputs e 40 to 85 C operating temperature range e Integrated high reliability power supply eliminates the need for external power transformer Panel Layout of PTC 101 Series Top Panel View PTC 101 LV Front Panel View PTC 101 M ST LV Rear Panel View PTC 101 HV Front Panel View PTC 101 M SC HV Rear Panel View 3 Or oe Grounding screw Terminal block for power input Heat dissipation vents and relay output DIP switch Power input PWR LED Fiber Link Active LED 100BaseFX Port ST SC LC connector 10 100BaseT X TP port 10 Mbps LED TP port 100 Mbps LED Model Name DIN Rail mounting kit Dimensions For PTC 101 M SC HV Others are provided by requests oo 42 4 mm 1 67 in 40mm 1 57 in 0 59 in 19mm 19 mm 0 75 in 67 4 mm 2 65 in ios a ry Bor OOOO ul 89 S ww SLppL u go s ww S L Y L 01 4 mm 3 99 g 11 4 mm 4 39 in 123 46 mm 4 86 in 123 46 mm 4 86 in Side View HV Models Side View LV Models 101 4 mm 3 99 in 12 06 mm 0 47 in 111 4 mm 4 39 in ureo mn D 1 0 0 30 5 mm UZES ww TSEL Industrial Media Converter
4. mode Single mode Wavelength 1300 nm 1310 nm Max TX 10 dBm 0 dBm Min TX 20 dBm 5 dBm RX Sensitivity 32 dBm 34 dBm Link Budget 12 dB 29 dB Typical Distance 5 kn 40 km 4km Saturation 6 dBm 3 dBm a 50 125 um 800 MHz km fiber optic cable b 62 5 125 um 500 MHz km fiber optic cable c 9 125 um 3 5 PS nm km fiber optic cable Power Requirements Input Voltage Power Supply Type Power Consumption Fuse Rating LV DC 20 VDC 72 VDC 170mA 20VDC 3 15A T 2 HV AC 85 VAC 264 VAC 73mA 85VAC 3 15A T 2 HV DC 88 VDC 300 VDC 47mA 88VDC 3 15A T 2 Connection Removable Terminal Block Overload Current Protection Reverse Polarity Protection Physical Characteristics Housing Dimensions W x H x D Weight Environmental Limits Operating Temperature Storage Temperature Operating Humidity 1 6 A protects against two signals shorted together Present Aluminum IP30 protection 122 5 x 90 x 20 mm 4 82 x 3 54 x 0 79 in Product only 690 g Packaged 875 g 40 to 85 C 40 to 185 F 40 to 85 C 40 to 185 F 5 to 90 10 Regulatory Approvals Safety EMI EMS Power Automation Rail Traffic Warranty UL 60950 1 FCC Part 15 CISPR EN55022 class A EN61000 4 2 Edition 1 2 2001 04 Level 4 N61000 4 3 1995 A1 2001 IEC 61000 4 3 2002 A1 2002 Level 3 EN61000 4 4 2004 Level 4 EN61000 4 5 2001 04 Level 4 EN61000 4 6 2004 11 Level 3
5. other optical line is used transmit data from device II to device I for full duplex transmission All you need to remember is to connect the Tx transmit port of device I to the Rx receive port of device II and the Rx receive port of device I to the Tx transmit port of device II If you are making your own cable we suggest labeling the two sides of the same line with the same letter A to A and B to B as shown below or Al to A2 and B1 to B2 SC Port Pinouts SC Port to SC Port Cable Wiring A A TN i E fru Tx _ AEA ie B B pg Cable Wiring Rx A A Cable Wiring Redundant Power Inputs For PTC 101 LV series both power inputs can be connected simultaneously to live DC power sources If one power source fails the other live source acts as a backup and automatically supplies all of Moxa Industrial Media Converter s power needs DIP Switch Setting DIP No Function ON OFF 1 Auto Negotiation Enable Disable ON Enables Auto Negotiation function the speed and duplex states for each port link segment are automatically configured using the highest performance interoperation mode OFF Disables Auto Negotiation function the speed and duplex states depend on the manual setting configuration 2 Force TP Speed 100Mbps 10Mbps Only when Auto Negotiation is disabled ON Fo
6. Moxa Industrial Media Converter PTC 101 Hardware Installation Guide Second Edition February 2010 MOXA 2010 Moxa Inc All rights reserved Reproduction without permission is prohibited F1 4 No 135 Lane 235 Pao Chiao Rd Shing Tien City Taipei Taiwan R O C TEL 886 2 8919 1230 P N 1802001016011 Overview Moxa Industrial Media Converter which is specially designed for reliable and stable operation in harsh industrial environments provides industrial grade media conversion between 10 100BaseT X and 100BaseFX PTC 101 s reliable industrial design is excellent for keeping your industrial automation applications running continuously and comes with a relay output warning alarm to help prevent damages and losses This product has a wide operating temperature range from 40 to 85 C and is designed to withstand a high degree of vibration and shock The rugged hardware design makes PTC 101 perfect for ensuring that your Ethernet equipment can withstand critical industrial applications such as in hazardous locations and complies with FCC UL and CE standards Package Checklist Moxa Industrial Media Converter is shipped with the following items If any of these items is missing or damaged please contact your customer service representative for assistance e Moxa Industrial Media Converter e Hardware Installation Guide e Moxa Product Warranty booklet Features e Supports 10 100Base TX auto negotiation and
7. nection The 10 100BaseT X ports located on PTC 101 s front panel are used to connect to Ethernet enabled devices Below we show pinouts for both MDI NIC type ports and MDI X HUB Switch type ports and also show cable wiring diagrams for straight through and cross over Ethernet cables RJ45 8 pin MDI Port Pinouts RJ45 8 pin MDI X Port Pinouts Pin Signal Pin Signal 1 TxX 1 8 1 Rx 1 8 2 Te 2 Rx 3 Rx 3 Tx 6 6 Rx Tx RJ45 8 pin to RJ45 8 pin Straight Through Cable Wiring Switch Port Straight Through Cable NIC Port RJ45 Plug Pin 1 RJ45 RJ45 Connector Cable Wiring Connector TX 3 3 RX Tx 6 6 Rx Rx 1 il TX Rx 2 2 i Tx RJ45 8 pin to RJ45 8 pin Cross Over Cable Wiring Switch Port Cross Over Cable Switch Port NIC Port NIC Port RJ45 RJ45 Plug Pin 1 FRJ45 Connector Cable Wiring Connector Rx Tx 3 1 IRx Tx Rx Tx 6 2 Rx Tx Tx Rx 1 3 Tx Rx Tx Rx 2 6 Tx Rx 100BaseFX Ethernet Port Connection The concept behind the SC port and cable is quite straightforward Suppose you are connecting devices I and II Contrary to electrical signals optical signals do not require a circuit in order to transmit data Consequently one of the optical lines is used to transmit data from device I to device II and the
8. rces 100Mbps on Ethernet port OFF Forces 10Mbps on Ethernet port 3 Force TP Duplex Full Duplex Half Duplex Only when Auto Negotiation is disabled ON Forces Full Duplex on Ethernet port OFF Forces Half Duplex on Ethernet port 4 Link Fault Pass Through Enable Disable ON Enables Link Fault Pass Through the link status on the TX port will inform the FX port of the same device and vice versa OFF Disables Link Fault Pass Through the link status on the TX port will not inform the FX port 5 Operating Mode Store and Forward Pass Through ON Selects Store and Forward mode begins to forward a packet to a destination port after an entire packet is received The latency depends on the packet length OFF Selects Pass Through mode operates with the minimum latency Both transceivers are interconnected via internal MIIs and the internal switch engine and data buffer are not used Note With Pass Through mode enabled the Ethernet port and fiber port should transmit at 100 Mbps which is equivalent to full duplex mode Default DIP settings are all at ON position ATTENTION After changing the DIP switch setting you will need to power off and then power on the PTC 101 to activate the new setting LED Indicators The front panel of Moxa Industrial Media Converter contains several LED indica
9. t you label wiring to all devices in the system when necessary Grounding Moxa Industrial Media Converter Grounding and wire routing help limit the effects of noise due to electromagnetic interference EMI Run the ground connection from the ground screw to the grounding surface prior to connecting devices ATTENTION This product is intended to be mounted to a well grounded mounting surface such as a metal panel Wiring the Redundant Power Inputs for PTC 101 LV series The top five contacts of the 8 contact terminal block connector on the PTC 101 LV s top panel are used for the PTC 101 LV s two DC inputs Top and front views of one of the terminal block connectors are shown here Zai STEP 1 Insert the negative positive DC wires into the V V terminals Top View STEP 2 To keep the DC wires from pulling loose use a small flat blade screwdriver to tighten the wire clamp screws on the front of the terminal block connector a B S a oa ODODOODD STEP 3 Insert the plastic terminal block connector prongs into the terminal block til l p receptor which is located on the PTC 101 LV s top panel ATTENTION Before connecting PTC 101 LV to the DC power inputs make sure the DC power source voltage is stable Communication Connections PTC 101 models have one 10 100BaseT X Ethernet port and one 100BaseFX SC ST or LC type connector fiber port 10 100BaseT X Ethernet Port Con
10. tors The function of each LED is described in the table below Description Power is being supplied to power input PWR1 Power is not being supplied to power input PWR1 Power is being supplied to power input PWR2 Power is not being supplied to power input PWR2 Fiber port is active Data is being transmitted or Blinking received Off Fiber is inactive Ethernet port 100 Mbps link is On z active Data is being transmitted at 10 Yellow Blinking Mbps off Ethernet port 10 Mbps link is inactive On Ethernet port 100 Mbps is active Blinking Se being transmitted at 100 off Ethernet port 100 Mbps link is inactive Specifications Technology Standards IEEE 802 3 for 10BaseT IEEE 802 3u for 100BaseT X 100BaseFX Interface RJ45 ports 10 100BaseT X Fiber ports 100BaseFX SC ST LC connectors LED Indicators PTC 101 HV series PWR1 Fiber Link 10 100M TP port PTC 101 LV series PWR1 PWR2 Fiber Link 10 100M TP port Dip Switches Dip No Function ON OFF 1 Auto Negotiation Enable Disable 2 Force TP Speed 100 Mbps 10 Mbps 3 Force TP Duplex Full Duplex Half Duplex 4 Link Fault Pass Throuth Enable Disable 5 Operating Mode Store and Forward Pass Through Default DIP settings are all at ON position Alarm Contact One relay output with current carrying capacity of 1 A 24 VDC Optical Fiber 100BaseFX Multi
Download Pdf Manuals
Related Search