Sansui SLED5000 LED TV
Contents
1. Screws mounting holes 5 EN How to attach the stand NOTE e Unplug the AC cord from the AC INPUT terminal e Before beginning this process assure that the TV is laid on a clean safe and cushioned surface to avoid any damage to the unit e Do not touch or press the TV screen glass might break under pressure Place the TV on its front onto a table Align the stand s bottom plate supplied as seen here It will fit in only one direction Hold the unit and attach the stand as shown in figure 1 Figure 1 Finally secure the bottom plate with 5 screws supplied 4x12mm 5 32 x 15 32 inches as indicated by the arrows in figure 2 e Be sure to follow the instructions Insufficient tightening or incorrect installation of the stand will not support your unit correctly and could result in damage or injury from tip over How to remove the stand When you transport this product remove the stand and pack flat against the back of the unit in the carton To remove the stand perform these steps in reverse order For wall mounting the base must be removed To disconnect the base stand remove the 4 screws from the back see page 5 Warning To prevent injury which could be expected due to an eventual fall the TV must be fixed to the ground according to instruction see right image Fix to the appropriate ground with the screw not supplied NOTE e There is no liabilit2. 12 3 13 3 14 15 6 7 8 16 10 IFSA STOP SRIPF 11 HAW Gi 18 lpauses Cu 1 0 POWER Button Use to turn the power on off to the TV 2 DISPLAY Button When you press this button the current information will be displayed on a screen To remove the display from the screen press this button again 3 Direct Channel Selection Buttons 0 9 Allows direct access to any channel of the TV 4 Button This button is used when selecting digital channels 5 MENU Button Use to display the On Screen menu function 6 CURSOR 4 v lt gt Buttons Use to operate the menu functions of the TV 7 ENTER Button Use to enter or select information for On Screen operations 8 MUTE Button To turn off the sound press this button once The TV will be silenced and the symbol will appear on the screen The muting feature can be released by pressing the MUTE button again or one of the VOL VOLUME buttons 9 VOL VOLUME Buttons Press the button to increase or the button to decrease the sound level 10 INPUT SELECT Button Use to change the external input 11 CCD Button Use to select Closed Caption to CC Off CC On or CC on Mute 12 SLEEP Button To set the TV to turn off aftera preset amount of time use the SLEEP button on the remote control 13 PICTURE SIZE Button Use to change the picture size 14 RECALL Button This button allows you to go back to
3. TV operation To turn on the TV press POWER POWER indicator on the front of the unit changes green It may take approx 10 seconds for a picture to appear on screen 2 Adjust the volume level by pressing VOL or The volume level will be indicated on the screen by brown bars As the volume level increases so do the number of bars If the volume decreases the number of brown bars also decreases Set the signal type option to the appropriate position see Air Cable selection on page 20 Press the Direct Channel Selection 0 9 buttons to select the channel If you press only channel number channel selection will be delayed for a few seconds TO SELECT ANALOG CHANNELS RS 1 9 Press 1 9 as needed Example to select channel 2 press 2 then press ENTER 10 99 Press the 2 digits in order Example to select channel 12 press 1 2 then press ENTER 100 135 Press the 3 digits in order Example to select channel 120 press 1 2 0 then press ENTER TO SELECT DIGITAL CHANNELS Press the first 1 3 digits then press the button followed by the remaining number Example to select channel 15 1 press 1 5 1 then press ENTER e f a channel is selected with only audio content Audio Only will be displayed on the screen e f a channel is selected with a weak digital signal No Signal will be displayed on the screen The same program may be available on either
4. Video Audio cord not supplied re EG ME To connect the TV to a DVD player with Component Video Input You can enjoy a high quality picture by connecting the units COMPONENT VIDEO OUT jacks of your DVD player with the component video cables not supplied Right of the unit To COMPONENT IN go Y VIDEO Pb Pr To AUDIO IN To Audio OUT OG Audio cord x ae C not supplied Lo a A Component video cord not supplied m To Component OUT NOTE e Component Video input of the unit are for use with a device which output 480i 1080i interlaced signals and 480p 720p 1080p progressive signals To connect the TV to a camcorder or a game console To playback from a camcorder connect the camcorder to the unit as shown This unit can also be used as a display device for many video games However due to the wide variety of signals generated by these devices and subsequent hook up variations required they have not all been included in the suggested connection diagrams You ll need to consult each component s Owners Manual for additional information Right of the unit To VIDEO AUDIO IN To Video Audio OUT Video Audio cord not supplied CN RS COMPONE RE de FD or GAME CONSOLE Connections to other equipment Using an AV Amplifier with built in digital surround If you are using an AV Amplifier with built
5. Playback files 1 Press lt or gt to select Photo or Movie at Media Selection and press ENTER 2 Press lt or to select C then press ENTER 3 Select folder or file with a W lt and then start the playback with ENTER You can playback the files with the following remote control buttons Button Action Press to start the playback ENTER Press to open the folder Press to open the operation window Il Press to pause the playback gt Press to start the playback or slideshow Press to stop the playback During the playback press to select the next PP file iis During the playback press to select the previous file During the playback press to select search PP forward Ee During the playback press to select search backward Details of operation commands Icon gt il lt lt lad te Lin Operation Play Resume playback Pause Skip file to reverse forward direction Stop Repeat playback Press ENTER repeatedly to select desired repeat option Show the playlist Press a or v and ENTER to select the playback Show the file information Rotate the image Zoom in out Move the frame from the center position Review Fast playback Select start point then select end point Repeat material between two selected points Slow motion Playback One frame is advanced each time select this command Direct jump by desired time Recepti
6. Text Opacity AAA AA AAA q q q Text Color 4 q q q Background Opacity You can select from among the following items and parameters Text Style Select display font style Text Size Select display font size Text Edge Style Select display font edge style Text Edge Color Select display font edge color Text Color Select foreground color Background Color Select background color Text Opacity Select foreground opacity level Background Opacity Select background opacity level NOTE e You cannot set both Text Color and Background Color as a same color Setting the picture size You can change to a variety of picture sizes Natural Full Zoom Cinema Native For PC mode only Selecting the picture size 1 Select Picture Advanced Settings Picture Size 2 Press lt or to select the desired picture size as described below NOTE e Selectable picture sizes may vary depending on the input source or broadcast signal e You can be select desired size of picture by pressing PICTURE SIZE on the remote control Natural In some cases this image will display the size of standard 4 3 with a black side bar Full Full will display the picture at the maximum size Zoom for letter box programs with subtitles To fill the width of the screen it is extended horizontally However it is only slightly extended at the top and the bottom The top and botto
7. ETL Follow all instructions supplied by the display and wall mount manufacturers If you have any doubts about your ability to safely install your flat panel display contact your retailer about professional installation Make sure that the wall where you are mounting the display is appropriate to support the weight of the unit product and wall mount If you are unsure contact a professional installer A minimum of two people are required for installation Flat panel displays can be heavy IMPORTANT SAFETY INSTRUCTIONS CONDENSATION Moisture will form in the operating section of the unit if the unit is brought from cool surroundings into a warm room or if the temperature of the room rises suddenly When this happens unit s performance will be impaired To prevent this let the unit stand in its new surroundings for about an hour before switching it on or make sure that the room temperature rises gradually Condensation may also form during the summer if the unit is exposed to the breeze from an air conditioner In such cases change the location of the unit HOW TO HANDLE THE LCD PANEL Do not press hard or jolt the LCD panel It may cause the LCD panel glass to break and injury may occur e Ifthe LCD panel is broken make absolutely sure that you do not touch the liquid in the panel This may cause skin inflammation If the liquid gets in your mouth immediately gargle and consult with your doctor Also if the liquid gets
8. Ts TT I If the character which you desire appears press You can also change the position which input character by pressing lt or gt Repeat this step to enter the rest of the characters 4 Repeat steps 2 3 for other channel You can assign a label to each channel 5 When you finish inputting the label name press EXIT to return to the normal screen NOTE e The channel labels will be reset after Automatic Search on page 20 Setting the V Chip An age limitation can be set to restrict children from viewing or hearing violent scenes or pictures that you may choose to exclude The restriction applies to TV Rating and Movie Rating if this data is transmitted You may set this restriction separately To use the V Chip function you must register a password To register a password 1 Select Lock then press V 2 Press 0000 using Number buttons 0 9 This is default Ts INNY Le Q Lock Enter Password x appears instead of the number NOTE e f you forget the password contact Customer Service at 1 800 289 0980 for assistance Your original remote control will be required e To avoid forgetting the password write it down and keep in a safe place How to enter the V Chip menu 1 Select Lock menu then press V 2 Use Number buttons 0 9 to enter your password To V Chip connected devices 1 In the Lock menu press A or to select V Chip then press
9. WEBSITE AT POUR OBTENIR DES INFORMATIONS SUR NOS AUTRES PRODUITS POUR COMMANDER DES ACCESSOIRES OU LE RECYCLAGE VEUILLEZ VISITER NOTRE SITE WEB www sansuiproducts com Before operating the unit please read this manual thoroughly Avant de faire fonctionner l appareil veuillez lire le pr sent guide attentivement CANTONS ENA ENGLISH The lightning flash with arrowhead symbol within an equilateral triangle CAUTION is intended to alert the user to the presence of uninsulated dangerous RISK OF ELECTRIC SHOCK voltage within the product s enclosure DO NOT OPEN that may be of sufficient magnitude to constitute a risk of electric shock CAUTION To REDUCE THE RISK OF ELECTRIC The exclamation point within an SHOCK DO NOT REMOVE COVER equilateral triangle is intended to alert the user to the presence of OR BACK NO USER SERVICEABLE important operating and maintenance PARTS INSIDE REFER SERVICING TO servicing instructions in the literature QUALIFIED SERVICE PERSONNEL See OM Pay ENASERRIARCE WARNING To PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE TO PREVENT THE SPREAD OF FIRE KEEP CANDLES OR OPEN FLAMES AWAY FROM THIS PRODUCT AT TIMES CAUTION To PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE WARNING This equipment has been tested and found to comply w
10. an analog channel or a digital channel You may choose to watch either format VHF UHF CABLE CHANNELS 14 36 37 59 60 85 86 94 95 99 100 135 01 NOTE e Ifachannel with no broadcast is selected the sound will automatically be muted e lt may take a few seconds for a digital channel picture to appear on screen after being selected To select the video input source To view a signal from another device connected to your TV such as a VCR player press INPUT SELECT then press a or v then press ENTER CH A V Press and release CH A V The channel automatically stops at the next channel set into memory For proper operation before selecting channels they should be set into the memory See Channel setup on page 20 DISPLAY Press DISPLAY to display the current information on the screen When the TV receives a digital signal the digital information will appear 15 1 cc service Monoscope 80 1 SD ENT 2E TV 14 D CH 1 3_ARTE_Monosco_0820_0000_0030_Audio6_ABCDEFGHIJKLMNOPQ RSTUVWXYZabcdefghijkimnopqrstuvwxyz_ABCDEFGHIJKLMNOPQR STUVWXYZabcdefghijkimnopqrs tuvwxyz_ABCDEFGHIJKLMNOPQRS TUVWXYZabcdefghijkimnopars e Channel number e DTV Signal condition e Channel label if preset Broadcast program name e V Chip rating e Current date and time e Program guide e Audio language e Resolution e Closed Caption Press DISPLAY again to clear the call display NOTE e After a few seconds DISPLAY screen
11. in your eyes or touches your skin consult with your doctor after rinsing for at least 15 minutes or longer in clean water Possible Adverse Effects on LCD Panel If a fixed non moving pattern remains on the LCD Panel for long periods of time the image can become permanently engrained in the LCD Panel and cause subtle but permanent ghost images This type of damage is NOT COVERED BY YOUR WARRANTY Never leave your LCD Panel on for long periods of time while it is displaying the following formats or images e Fixed images such as stock tickers video game patterns TV station logos and websites e Special formats that do not use the entire screen For example viewing letterbox style 16 9 media on anormal 4 3 display black bars at top and bottom of screen or viewing normal style 4 3 media ona widescreen 16 9 display black bars on left and right sides of screen The following symptoms are not signs of malfunction but technical limitation Therefore we disclaim any responsibility for these symptoms e LCD Panels are manufactured using an extremely high level of precision technology however sometimes parts of the screen may be missing picture elements or have luminous spots This is not a sign of a malfunction e Do not install the LCD Panel near electronic equipment that produces electromagnetic waves Some equipment placed too near this unit may cause interference e Effect on infrared devices There may be interference while
12. of original purchase ORION will provide in home repair service only by an ORION authorized Independent Service Center at no charge Also if an original part fails due to manufacturing defect in material and workmanship within one year from date of original purchase we will replace the defective part provided the defect or malfunction is verified along with dated proof of purchase There are ORION authorized Independent Service Centers located throughout the country For the one nearest you DIAL TOLL FREE 1 800 289 0980 or visit our website at www sansuiproducts com ORION will not be liable for damages incurred in shipment of the unit If there are no ORION authorized Independent Service Centers in your area please call 1 888 296 7466 for assistance Note This warranty is void if the product is a Damaged through negligence misuse abuse or accident b Used in a commercial application or rentals c Modified or repaired by anyone other than an Independent Service Center authorized by ORION to effect warranty repairs to the class of product or by the ORION Factory Service Center d Damaged because it is improperly connected to the equipment of other manufacturers This warranty does not cover a Damage to equipment not properly connected to the product b Costs incurred in the shipping of the product to an ORION authorized Independent Service Center or ORION Factory Service Center c Damage or improper operation of unit ca
13. the previous channel selected by just pressing the RECALL button Press this button again to return to the channel you were watching 15 EXIT Button Press to remove setup menu 16 AUDIO Button Change soundtrack language 17 CH CHANNEL A V Buttons To change the channels of the TV 18 USB Media control buttons See page 25 Before using the remote control batteries must first be installed HOW TO INSTALL BATTERIES 1 Open the battery compartment cover 2 Install two AAA batteries supplied 3 Replace the battery compartment cover Use two AAA size batteries The batteries may last approximately one year depending on how much the remote control is used For best performance it is recommended that batteries should be replaced on a yearly basis or when the remote operation becomes erratic Do not mix old and new batteries or different types BATTERY PRECAUTIONS These precautions should be followed when using batteries in this device e Use only the size and type of batteries specified e Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Reversed batteries may cause damage to the device e Do not mix different types of batteries together e g Alkaline Carbon zinc or Rechargeable or old batteries with fresh ones If the device is not to be used for a long period of time remove the batteries to prevent damage or injury from p
14. using infrared devices such as infrared cordless headphones SAFETY PRECAUTIONS The unit emits heat when in operation Do not place any covers or blankets on the unit this may cause overheating Do not block ventilation holes or set up near radiators Do not place in direct sunshine When placing on a shelf leave 4 inches 10 cm free space around the entire unit A 4 4inches x 4inches Notes when mounting the TV on a wall e Ifthe unit is to be mounted on the wall contact the retailer where you purchased the TV for advice and have the equipment professionally installed Incomplete or improper installation may cause injury to you and or damage to the TV e Bracket holes To attach a wall M rR bracket not supplied attach where indicated in the drawing right e This manufacturer recommends professional installation e Utilize an appropiate bracket and fasteners sufficient to accommodate the size and weight of the unit e Assure the wall to which the unit is to be mounted will safely support the size and weight of the unit using the bracket and fasteners you have selected e Keep cords and cables connected to this flat panel display out of reach of children e To hang the television on a wall remove these screws and then remove a stand Before performing work spread cushioning over the base area to lay the TV on e Before wall mounting please check carefully the location of the TV s
15. 4 inches Depth 237 mm 9 21 64 inches 5 C 40 C Less than 80 RH 1257 3mmV 50 class 49 50 diagonal Transmission TFT color LCD panel 1920 H x 1080 V US System M ATSC standard 8VSB QAM VHF 2 13 UHF 14 69 CATV 14 36 A W 37 59 AA WW 60 85 AAA ZZZ 86 94 86 94 95 99 A 5 A 1 100 135 100 135 01 4A Frequency synthesized Video RCA 1V p p 75 ohms Audio RCA 8 dBm 50k ohms Component video Y 1 V p p 75 ohms Pb Pr 0 7 V p p 75 ohms HDMI HDMI compliant type A connector HDCP compliant E EDID compliant Suggested scan rates 480p 480i 720p 1080i 1080p HDMI Audio 2 channel PCM 32 44 1 48 kHz sampling frequency 16 20 24 bits per sample PC Monitor Mini Dsub 15pin Antenna VHF UHF In 75 ohms coaxial Digital audio out 0 5 V p p 75 ohms terminated 40 6 mm x 121 9 mm 1 5 8 inches x 4 13 16 inches 8 ohms x 2 10 0W 10 0W Remote control Batteries AAA x 2 Stand Screws 4x12mm 5 32 x 15 32 inches x 5 Designs and specifications are subject to change without notice 64 SANSUI WAHBA N TY 50 CLASS LED LCD HDTV ORION warrants this product to be free from manufacturing defects in material and workmanship under normal use and conditions for a period of 1 year from date of original purchase in the United States Should service be necessary under this warranty for any reason due to a manufacturing defect or malfunction during the first 12 months from date
16. C in the United States and other countries Power source TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet AC Outlet Wider Hole and Blade Polarized AC Cord Plug One blade is wider than the other NOTE e Never connect the AC line cord plug to other than the specified voltage 120V 60HZz Use the attached power cord only e If the polarized AC cord does not fit into a non polarized AC outlet do not attempt to file or cut the blade It is the user s responsibility to have an electrician replace the obsolete outlet e If you cause a static discharge when touching the unit and the unit fails to function simply unplug the unit from the AC outlet and plug it back in The unit should return to normal operation 7 EN Contents Before using your unit IMPORTANT SAFETY INSTRUCTIONG 3 SAFETY PRECAUTIONS 5 How to attach the stand 6 How to remove the stand 6 F AIUT SE SE Se eh al A Ann 7 Power SOUICE cccceceececeeceeeeceeeeceeeeseueeeeneeeeneees 7 Contents tical aaa eee ad 8 Parts And functions 0 cece eeccecceceeeeeeeeceeeeeeeeees 9 Remote control 10 Antenna connections 11 Cable TV connections 11 Connections to other equipment 12 TV operation Slang SOUPLE Men ns 15 INFOP ATIONS rat EE 15 Quick guide for menu operation 16 Convenience functions cceccece
17. STAR In Home mode default setting Then press v or ENTER NOTE e This unit has been preset to STORE brightness This setting does not qualify under ENERGY STAR To reduce brightness and energy consumption change setting to HOME This setting does qualify under ENERGY STAR Press or ENTER to go to next step KO Press lt or gt to select your time zone then press v or ENTER e In the rare event that you live within broadcast range of two stations in two different time zones the TV may recognize the wrong station for the auto clock set Press lt or gt to select daylight saving time on or off then press Y or ENTER Press lt or gt to select desired time format then press w or ENTER Press or ENTER to go to next step Press a or Y to select Air Cable then press lt or to select signal type that you using then press w or ENTER Press or ENTER to go to next step O ON O O1 O Auto scan will begin After tuning is completed the TV channel appears on the screen e Depending on the reception condition it may take up to 30 minutes to complete memorizing digital cable channels Please allow the process to complete without interruption NOTE e If you press MENU or EXIT in the process of Automatic Search the Auto scan stops and changes to normal screen e When you make a menu selection your changes occur immediately You do not have to press MENU to see your changes
18. TER 2 Press lt or gt to set CC Setting to CC On or CC on Muting CC On Captions will be displayed on the screen CC on Muting Only when you press MUTE captions will be displayed CC Off Captions will not be displayed on the screen 3 Press A or v to select Analog Caption or Digital Caption When you select Analog Caption you can choose from CC1 4 Text1 4 When you select Digital Caption you can choose from Service1 6 and Off 4 Press lt or gt to select the desired Closed Caption mode for both Digital and Analog Captions NOTE e Depending on the broadcast signal some Analog Captions will function with a Digital broadcast signal This step prevent that two kind of captions are overlapping NOTE e lf the program or video you selected is not closed Captioned no captions will display on screen If text is not available in your viewing area a black rectangle may appear on screen If this happens set the CC Setting to CC Off When selecting Closed Captions the captioning will be delayed approx 10 seconds If no caption signal is received no captions will appear but the television will remain in the Caption mode Misspellings or unusual characters may occasionally appear during Closed Captioning This is normal with Closed Captioning especially with live programs This is because during live programs captions are also entered live These transmissions d
19. ect the TV to a PC Personal Computer BEFORE YOU CONNECT THIS TV TO YOUR PC CHANGE THE ADJUSTMENT OF YOUR PC S RESOLUTION AND REFRESH RATE 60 HZ Connect one end of a male to male VGA cable to the video cord of the computer and the other end to the VGA connector PC MONITOR IN on the rear of the TV Attach the connectors firmly with the screws on the plug In case of a Multimedia computer connect the audio cord to the audio output of your Multimedia computer and to the AUDIO IN L R connector of the AUDIO IN L R jack of the TV You can also connect the PC with HDMI cable If you use HDMI cable you don t have to connect the audio cord If you use DVI to HDMI cable please connect audio cord as same way as VGA cable Press INPUT SELECT on the remote control to select PC mode Switch on the computer The TV can operate as the computer monitor Rear and right of the unit Monitor Display modes Mode Resolution Refresh rate VGA 640x480 60 75 Hz Room VGA 720x400 70Hz e SVGA 800x600 60 75 Hz XGA 1024x768 60 70 75 Hz WXGA 1360x768 60Hz SXGA 1280x1024 60Hz WXGA 1440x900 60Hz WSXGA 1680x1050 60Hz FHD 1920x1080 60Hz To return to normal mode Press INPUT SELECT again To HDMI IN To AUDIO IN To PC HDMI cable not supplied MONITORIN VGA cable not supplied Audio cord not supplied NOTE e The on screen displays will have a different appearance in PC mode than in TV mode e f there is
20. eeseeseeeeeeeeees 17 Channel Setup sans 20 Labeling channels 21 Setting the V Chip 21 Closed Caption 23 CE ODIIONS sans hinanmnninAnimae 23 Setting the picture size 24 Media Playback ccccesseeecsesseressenseressenses 25 Additional information Reception disturbances 27 Troubleshooting sensisse mes 28 SD CHICALIONS uen enateahenauus 29 limited WARRANTY 30 Parts and functions Front Right Side INPUT ENTER M INPUT ENTER button CH CHANNEL A V A buttons VOL VOLUME lt MENU buttons POWER button Remote sensor Power Indicator Red Standby Green On To display the menu screen Press MENU button to display the menu screen CH CHANNEL A V buttons VOL VOLUME buttons and INPUT ENTER button can be used to select the desired setting during the menu screen operations Right side PC MONITOR IN jack sn Rear HDMI DVI3 IN jack USB INPUT Sa i l HDMI DVI HDMI DVI1 2 IN jacks z qe THRE E wa LR tT ll AUDIO IN L R jacks Te aN AS CM i COMPONENT IN Y VIDEO Pb Pr jacks DIGITAL AUDIO COAXIAL OUT jack p a _1 AZ AUDIO OUT jacks eee Saal E ANT le a d F ACER HET ANT RF IN jack C ee ee Remote control
21. erference Make sure Signal Type option is in the appropriate mode If using antenna check UHF antenna connections Batteries are weak dead or inserted incorrectly Remote is out of range move closer to TV within 15 feet Make sure Remote is aimed at sensor Confirm there are no obstructions between the Remote and the TV Make sure the power cord is plugged in TV shuts off Sleep Timer is set e Power interrupted Closed Caption is not activated TV is not shown in your language OR WRITE TO ORION SALES INC 3471 N UNION DR OLNEY ILLINOIS 62450 e TV station experiencing problems or program tuned is not closed captioned Try another channel e Check Cable TV connection or VHF UHF antenna reposition or rotate antenna e Set closed caption decoder in the menu e Select proper language in the menu options FOR INFORMATION ON OUR OTHER PRODUCTS TO ORDER ACCESSORIES ONLINE OR FOR RECYCLING INFORMATION PLEASE VISIT OUR WEBSITE AT www sansuiproducts com Specifications GENERAL Power supply Power consumption Weight Dimensions Operating temperature Operating humidity Type Display method Number of Pixels Broadcasting system Receiving channels Tuner type Inputs Output Speakers Audio output power ACCESSORIES AC 120V 60Hz Operation 130W Stand by 0 5W 17 0kg 37 5 lbs Width 1 155 mm 45 15 32 inches Height 737 mm 29 1 6
22. eunepuTisation SS SANSUI 50 CLASS LED LCD HDTV LED LCD HDTV CATEGORIE 50 PO SLED5000 wy Hm HIGH DEFINITION MULTIMEDIA INTERFACE ENERGY STAR ATTENTION ATTENTION If you purchase a universal remote control from your local retailer please contact the remote manufacturer for the required programming code Si vous utilisez avec cet appareil une t l commande universelle autre que celle vendue avec ce t l viseur consultez la documentation accompagnant la telecommande universelle afin de connaitre le code num rique cor respondant au t l viseur AIR CABLE MODE SELECTION SELECTION DU MODE AIR CABLE When shipped from the factory the Signal Type option is set to the Cable Cable Television mode If not using Cable TV set this menu option to the Air position Lorsque l appareil sort de lusine l option Signal Type est en mode Cable cablodistribution Si vous n utilisez pas la c blodistribution s lectionnez l option Air IF CONTACT WITH CUSTOMER SERVICE IS REQUIRED PLEASE HAVE THE MODEL NUMBER READY PRIOR TO THE CALL SI VOUS DEVEZ COMMUNIQUER AVEC LE SERVICE CLIENTELE PRENEZ NOTE DU NUMERO DE MODELE AVANT D APPELER CUSTOMER SERVICE 1 800 289 0980 SERVICE SERVICE CLIENTELE 1 800 289 0980 ORION WEBSITE SITE WEB ORION FOR INFORMATION ON OUR OTHER PRODUCTS TO ORDER ACCESSORIES ONLINE OR FOR RECYCLING INFORMATION PLEASE VISIT OUR
23. h input source for your TV Default Antenna Cable l Satellite DTV DVD Blu ray You can select label from default value or input by yourself HD DVD XBOX Wii PS3 with a v alphabet select lt gt select character position Game Computer VCR DV Custom 10 characters PC Settings available only for PC mode To adjust the horizontal placing of the image To adjust the vertical placing of the image Eliminates the vertical CLOCK interfering lines Eliminates the horizontal PHASE interfering lines To adjust the all PC settings automatically Other Settings Audio Only You can turn off the picture on your TV and listen to the pro Off On gram audio only To exit audio only mode press any buttons except VOL MUTE on your remote control or unit Select location of TV Usually select Home Store Home Restore Default Select Yes then press ENTER Restore Picture Sound No Yes except Audio Language Time Sleep Timer Time Format and Auto Sleep only and Setup except Language settings to the default factory settings Initial Setup See page 15 TV mode only Channel setup This TV is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory skipping over unwanted channels Before selecting channels they must be programmed into the TV s memory To use this TV with an antenna set
24. icture size variation is normal when you adjust the CONTRAST or BRIGHTNESS settings CARE AND MAINTENANCE To prevent fire or shock hazard disconnect the TV from the power source before cleaning The finish on the cabinet may be cleaned with mild soap and a soft damp cloth and cared for as other furniture Use caution when cleaning or wiping the plastic parts 27 EN Troubleshooting Use the following checklist for troubleshooting if you have problems with your LCD TV Consult your local dealer or service outlet if problems persist Be sure all connections are properly made when using with other units SYMPTOMS POSSIBLE SOLUTIONS SYMPTOMS POSSIBLE SOLUTIONS TV does not operate Poor sound or no sound Poor picture or no picture Poor reception on some channels Poor color or no color Picture wobbles or drifts Make sure the power cord is plugged in Try another AC outlet Power is off check fuse or circuit breaker Unplug unit for an hour then plug it back in Station or Cable TV experiencing problems tune to another station Check sound adjustments VOL or MUTE Check for sources of possible interference Station or Cable TV experiencing problems tune to another station Make sure channels are set into memory Check antenna or Cable TV connections adjust antenna Check for sources of possible interference Check picture control adjustments Station or Cable TV experiencing
25. in digital surround sound you can enjoy various audio systems including Dolby Digital Surround audio that sounds just like the movie Connect an AV amplifier with built in Dolby Digital decoder DTS decoder or MPEG decoder etc as shown below Right of the unit Front Speaker Subwoofer Right TV Front Speaker Left le TT e S Center Speaker Coaxial digital cable not supplied To Coaxial Digital Audio Input M l D Surround Surround Speaker Left Speaker Right AV Amplifier with built in digital surround decoder NOTE e When you are viewing digital broadcast this unit will not work in conjunction with DTS audio or MPEG audio There will be no sound output if connected to an AV amplifier with a built in DTS decoder or MPEG decoder To connect a HDMI or a DVI device to the unit The HDMI input receives digital audio and uncompressed video from a HDMI device or uncompressed digital video from a DVI device When you connect to a DVI device with a HDMI to DVI adapter cable it transfers only video signal Separate analog audio cords required Rear and right of the unit To HDMI output HDMI cable type A connector not supplied HDMI device HDMI to DVI adapter cable HDMI type A connector not supplied DVI device Audio cord not supplied To AUDIO IN To DVI output Connections to other equipment To conn
26. ith the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user s authority to operate this equipment Location of the required marking The rating sheet and the safety caution are on the rear of the unit FCC Declaration of Conformity Compliance Statement Part 15 The Sansui SLED5000 LED LCD HDTV combination complies with Part 15 of the FCC rules Operation is subject to
27. ives a broadcast signal for Auto Clock the Auto Clock needs several minutes to set itself e nn ere the 4 v lt 4 gt the setting value is changed e Available nn ere when you selected Auto Clock to Off Auto i When the Set and Remote button operation are not operated OW 3 4 5Hours 3 4 5 Hours with specified period by this setting 3 4 5 Hours the power CONSOMME is changed to stand by mode automatically Power On Timer You can set the On Timer to automatically turn on the TV Off Once On To cancel the On Timer select Off Set the timer using A w 4 gt Power On Channel You can set the channel that appear with power on Power Off Timer You can set the Off Timer to automatically turn off the TV Off Once On sd To cancel the Off Timer select Off poen Timer Setthe timer using 4 4 gt S the timer Set the timer using 4 4 gt ssi A v 4 Convenience functions Language English Fran ais Espa ol You can choose from three different languages English Fran ais French and Espa ol Spanish for the on screen displays Select the language you prefer first then proceed with the other menu options OSD Timeout 5 15 30 45 60 Sec You can set the display time of OSD Menu Closed Caption See page 23 To adjust the size of the display by removing excess or Off On unattractive when set it to On Input Label The Input Label feature allows you to label eac
28. lt or gt to set to On 2 Press A or y to select Input Block then press gt or ENTER INNY Le Q Lock UnBlock AV 4 UnBlock Component UnBlock HDMI UnBlock HDMI2 UnBlock HDMI3 UnBlock PC UnBlock Media UnBlock Vv VVvvVvVvVvV 3 Press a or to select which device will be blocked then press lt or to select Block NOTE e f you want to use such a device again you should setting UnBlock in step 3 To set the V Chip 1 In the V Chip menu press A or to select V Chip then press lt or gt to set to On 2 Press or y to select US Rating then press gt or ENTER 3 Press A or Y to select which rating will be used then press gt or ENTER Each rating below will appear TV Rating CIRE a You can set the rating using age level and genre Age TV Y All children TVY7 7 years old and above TV G General audience TV PG_ Parental guidance TV 14 14 years old and above TV MA 17 years old and above When you select TV Y7 TV PG TV 14 or TV MA press DISPLAY to explain the rating Genre FV Fantasy Violence V Violence S Sex L Language D Dialogue Press 4 to select the desired rating then press ENTER Movie Rating Off None G All ages PG Parental guidance PG 13 Parental guidance less than 13 years old R Under 17 years old parental guidance suggested NC 17 17 years old and above X Adu
29. lt only Press lt gt to select the desired rating 4 Press EXIT to return to the normal screen V Chip function is activated now NOTE e The V Chip function is activated only on programs and input sources that include a rating signal To change the password 1 In the V Chip menu press A or v to select Change Password then press or ENTER 2 Enter a current password using Number buttons 0 9 3 Enter a new password using Number buttons 0 9 4 Enter the same password again to confirm The password is now registered Downloading the additional V Chip rating system As a supplement to the standard V Chip rating system your television will be able to download an additional rating system if such a system becomes available in the future To download the additional V Chip rating system when available 1 In the V Chip menu press a or v to select V Chip then press lt or gt to set to On 2 Press A or Y to select V Chip Set DTV then press gt or ENTER 3 If the TV is not storing the additional rating system the TV will begin downloading it which may take some time to be completed 4 Set your preferred content rating limits for the additional rating system NOTE e You can only download the additional V Chip rating system when your TV is receiving a digital signal e When you download the additional rating system it may take some time for the download to occur e The V Chi
30. m edges of the picture may be hidden Cinema for letter box programs The entire picture is uniformly enlarged it is stretched the same amount both wider and taller retains its original proportion The top and bottom edges of the picture may be hidden Full Native for PC mode only Detects the resolution of the signal of the image and it will be shown on the screen with same amount of pixels Media Playback You can enjoy viewing pictures and movies from your USB storage device 1 Connect the USB storage device into the USB Input terminal 2 Press INPUT SELECT then press A or Y to select Media then press ENTER NOTE e Do not disconnect a USB storage device while it is being accessed Doing so can damage the device or the files stored on the device You can safely connect or disconnect the USB storage device when the TV is not in media mode e Back up all the data in the USB storage device in case if data was lost due to unexpected accident We do not assume any liability for the losses by misuse or malfunction e Not all USB storage devices are compatible with this TV e The character that exceeds the display area is not displayed e Do not use USB extension cable e Playable files are JPEG jpg jpeg and Motion JPEG avi MJPEG format Media Browser Media Selection Photo1 jpg Information window NOTE e The content will change in accordance with each media setting screen
31. no video signal from the PC when the unit is in PC mode No Signal will appear on the TV screen e When the PC s resolution is set to 1920 x 1080 60 Hz FHD mode a signal that differs from the FHD signal which has been confirmed operational on this TV may appear depending on the PC used In this case Auto or other Position Adjustment functions may fail to correct the image position To solve this problem change the PC settings to select another resolution To connect an audio system This connection allows you to use an audio amplifier and external speakers and adjust the audio level using the TV s remote control Right of the unit oe eo ee ee 1 I Amplifier COUT OOO OOO To AUDIO L R OUT To Audio L Input To Audio R Input Audio cord not supplied Starting setup The Initial Setup menu appears the first time you turn on the TV and assists you to specify the Air Cable setting and program your channels automatically IMPORTANT Make sure that the antenna or cable TV system connection is made 1 To turn on the TV press POWER POWER indicator on the front of the unit changes green It may take approx 10 seconds for a picture to appear on screen The Initial Setup function begins Initial Setup TV Location q Go to next step 2 Press a or v to select TV Location then press lt or to select Store or Home This product qualifies for ENERGY
32. nts or short out parts that could result in fire or electric shock Never spill or spray any type of liquid into the unit If an outside antenna or cable system EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE is connected to the unit be sure the antenna or cable system is grounded to provide some protection against voltage surges and built up static charges Section 810 of the National Electrical Code ANSI NFPA 70 provides information with respect to proper grounding of the mast and supporting S a ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT NEC SECTION 810 20 ELECTRIC SERVICE EQUIPMENT M GROUNDING CONDUCTORS DZ NEC SECTION 810 21 GROUND CLAMPS structure grounding of the lead in NEC NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING i S2898A ELECTRODE SYSTEM wire to an antenna discharge unit size NE yes coy Sa H of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode IMPORTANT SAFETY INSTRUCTIONS 20 When replacement parts are required be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 21 Upon completion of any service or repairs to this unit ask the service technician
33. o not allow time for editing When Captions are being displayed on screen displays such as volume and mute may be seen but may interfere with Closed Captions Some cable systems and copy protection systems may interfere with the Closed Captioned signal If using an indoor antenna or if TV reception is very poor the closed caption decoder may not appear or may appear with strange characters or misspelled words In this case adjust the antenna for better reception or use an outdoor antenna e CC Setting will be change to CC Off CC On or CC on Muting by each pressing CCD on the remote control CC options When you have selected Custom as the display method you can adjust the various setting listed below as follows This feature is designed to customize Digital Caption only 1 Select Setup Closed Caption then press or ENTER 2 Press lt or to set CC Setting to CC On or CC on Muting Press or YW to select Digital Caption Style then press or ENTER Press A or Y to select Digital CC Preset then press lt or gt to select Custom Press A or Y to select the desired item then press lt or gt to change the setting g CERON E Sound Time Setup Lock Channel Digital CC Preset d Default Text Style Default Text Size Default Text Edge Style Default Default Default Text Edge Color Default Default Default Background Color
34. o the Antenna Jack on the TV Follow the connections shown below Set the TV to the output channel of the Converter Descrambler box usually channel 3 or 4 and use the Converter Descrambler box to select channels Incoming 75 ohm Antenna Cable TV Jack Cable 75 ohm Cable to TV For subscribers to unscrambled Cable TV service with scrambled premium channels If you subscribe to a Cable TV service in which basic channels are unscrambled and premium channels require the use of a Converter Descrambler box you may wish to use a signal Splitter and an A B Switch box available from the Cable TV company or an electronics supply store Follow the connections shown below With the switch in the B position you can directly tune any nonscrambled channels on your TV With the switch in the A position tune your TV to the output of the Converter Descrambler box usually channel 3 or 4 and use the Converter Descrambler box to tune scrambled channels Incoming Converter 75 ohm Descrambler rane Cable TV Jack ae Ca Splitter A B Switch CD Connections to other equipment The exact arrangement you use to interconnect various video and audio components to this unit is dependent on the model and features of each component Check the Owners Manual provided with each component for the location of video and audio inputs and outputs To connect the TV to a VCR Right of the unit To VIDEO AUDIO IN To Video Audio OUT VCR
35. on disturbances Most types of television interference can be remedied by adjusting the height and position of the VHF UHF antenna Outdoor antennas are recommended for best results The most common types of television interference are shown below If one of these symptoms appear when the TV is connected to a Cable TV system the disturbance may be caused by the local Cable TV company broadcast IGNITION Black spots or horizontal streaks may appear the picture may flutter or drift Usually caused by interference from automobile ignition systems neon lamps or AC powered tools and appliances such as drills or hair dryers GHOSTS Ghosts are caused by the television signal following two paths One is the direct path and the other is reflected by tall buildings hills or other large objects Changing the direction or position of the antenna may improve the reception SNOW If the TV is located far from the TV station in a fringe reception area where the signal is weak small dots may appear in the picture If the signal is extremely weak the installation of a larger external antenna may be necessary RADIO FREQUENCY INTERFERENCE RFI Caused by two way radios this type of interference produces moving ripples or diagonal streaks in the picture Some cases may cause a loss of contrast in the picture Changing the direction and position of the antenna or installing an RFI filter may improve the picture PICTURE SIZE VARIATION A slight p
36. ossible battery leakage Do not try to recharge batteries not intended to be recharged they can overheat and rupture Follow battery manufacturer s directions Antenna connections If you are using an indoor or outdoor antenna follow the instructions below that correspond to your antenna system If you are using a Cable TV service see Cable TV connections Combination VHF UHF Antenna Single 75 ohm cable Ant Connect the 75 ohm cable from the combination ey VHF UHF antenna to the Antenna Jack ANT SDS 0 RE Cable Cable TV connections This TV has an extended tuning range and can tune most cable channels without using a Cable TV Converter box Some cable companies offer premium pay channels where the signal is scrambled Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the Cable TV company For subscribers to basic Cable TV service 75 ohm For basic Cable TV service not requiring a Converter Antenna Coaxial Descrambler box connect the 75 ohm Coaxial Cable directly Jack Cable to the Antenna Jack on the back of the TV Com For subscribers to scrambled Cable TV service If you subscribe to a Cable TV service which requires the use of a Converter Descrambler box connect the incoming 75 ohm Coaxial Cable to the Converter Descrambler box Using another 75 ohm Coaxial Cable connect the output jack of the Converter Descrambler box t
37. p rating information and system are not determined or controlled by the TV The standard V Chip rating system is available whether your TV is receiving a digital signal or not and will block both analog and digital programs To set the restriction level using the standard V Chip rating system select US Rating in step 2 e The downloadable V Chip rating system is an evolving technology and availability content and format may vary To clear the V Chip Set DTV In the V Chip menu press a or to select V Chip then press lt or gt to set to On Press A or y to select RRT Clear then press gt or ENTER The confirmation window will appear Press to select Yes then press ENTER Your V Chip Set DTV will clear Closed Caption WHAT IS CLOSED CAPTIONING This television has the capability to decode and display Closed Captioned television programs Closed Captioning will display text on the screen for hearing impaired viewers or it will translate and display text in another language Captions This Closed Caption mode will display text on the screen in English or another language Generally Closed Captions in English are transmitted on CC1 and Closed Captions in other languages are transmitted on CC2 Text The Text Closed Caption mode will usually fill 1 2 of the screen with a programming schedule or other information 1 Select Setup Closed Caption then press or EN
38. problems tune to another station Make sure channels are set into memory Station is weak adjust antenna to receive desired station Check for sources of possible interference Station or Cable TV experiencing problems tune to another station Make sure channels are set into memory Check picture control adjustments Check antenna or Cable TV connections adjust antenna Check for sources of possible interference Station or Cable TV experiencing problems tune to another station Make sure channels are set into memory Cable TV company is scrambling signal Adjust antenna BLOCK NOISE PICTURE FREEZE Block noise or picture freeze may appear on the screen caused by weak signals interference from automobile ignition systems neon lamps or AC powered tools and appliances such as drills or hair dryers 3 SANSUI FOR CUSTOMER SERVICE ADDITIONAL SET UP AND OPERATING ASSISTANCE OR TO ORDER ACCESSORIES PLEASE CALL 1 800 289 0980 WHEN CALLING CUSTOMER SERVICE PLEASE HAVE YOUR MODEL NUMBER READY Digital broadcasting screen problem No CATV reception Horizontal or diagonal bars on screen No reception above channel 13 No Remote operation Check digital signal strength Check all Cable TV connections Set Signal Type menu option to the Cable mode Station or Cable TV system problems try another station Check antenna connections adjust or re direct antenna Check for sources of possible int
39. ptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over S3125A Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Apparatus should not be exposed to dripping or splashing and objects filled with liquids such as vases should not be placed on the apparatus An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock Do not push objects through any openings in this unit as they may touch dangerous voltage poi
40. t panel displays are popular purchases However flat panel displays are not always supported on the proper stands or installed according to the manufacturer s recommendations Flat panel displays that are inappropriately situated on dressers bookcases shelves desks speakers chests or carts may fall over and cause injury THIS MANUFACTURER CARES The consumer electronics industry is committed to making home entertainment enjoyable and safe TUNE INTO SAFETY One size does NOT fit all Follow the manufacturer s recommendations for the safe installation and use of your flat panel display Carefully read and understand all enclosed instructions for proper use of this product Don t allow children to climb on or play with furniture and television sets Don t place flat panel displays on furniture that can easily be used as steps such as a chest of drawers Remember that children can become excited while watching a program especially on a larger than life flat panel display Care should be taken to place or install the display where it cannot be pushed pulled over or knocked down Care should be taken to route all cords and cables connected to the flat panel display so that they cannot be pulled or grabbed by curious children WALL MOUNTING IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY ALWAYS Use a mount that has been recommended by the display manufacturer and or listed by an independent laboratory such as UL CSA
41. the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The party responsible for compliance to these rules is ORION AMERICA INC e SE an ae 1105 SOUTH MAIN STREET PRINCETON INDIANA Sa h a um 47670 U S A Ph 1 800 289 0980 Record the model number and serial number Model number Serial number LEN 2 IMPORTANT SAFETY INSTRUCTIONS Soe eS DS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience rece
42. the menu follow the On Screen prompts to set your preferences Picture Preference You can adjust the picture quality to your preference Available only when you selected User e Tint is available only in Analog TV and AV mode Advanced Settings OOO Noise Reduction To set the level of decreasing noises included in the video Medium High Off Signal Low Use this feature to change the Black level automatically according to the brightness of an image The Black level will become dark in a dark scene If ECO is selected the power consumption is reduced e DBC is not available in Media mode e s o DLC Dynamic Luminance Contrast function would adjust the luminance follow the average brightness automatically Fm ese A smoother motion may be obtained by setting the Film HDMI Mode Select the HDMI input signal as Video for video or Graphic Video Graphic OREO Off ECO On 17 EN Convenience functions Equalizer Settings Equalizer Mode Standard Music You can choose a basic equalizer mode Depending on this Movie Sports setting the following detail setting is set to default value of each mode 150 Hz 500 Hz The setting of this item adjusts the audio level of its 1K Hz 5K Hz frequency corresponding to each setting 10K Hz e Available only when you selected User Adjust the left and right sound channel volume The multi channel TV sound MTS feature provides high fideli
43. the signal type option to the Air mode When shipped from the factory this menu option is in the Cable mode Air Cable selection 1 Select Channel Air Cable 2 Press lt or gt to select Air or Cable Air VHF UHF channels Cable CABLE TV channels gz 2 Sound Time Setup Lock Channel Air Cable lt Cable Automatic Search Channel List Show Hide Channel Number Channel Label NOTE e t may take a few seconds for a digital channel picture to appear on screen after being selected Automatic Search 1 Select Channel Automatic Search then press gt or ENTER ou Sound Time Setup Lock Channel Are you sure to Automatic Search C Ys 2 In confirmation window Press to select Yes then press ENTER The TV will begin memorizing all the channels available in your area e It may take from 15 minutes to 30 minutes to complete memorizing digital cable channels Depending on the reception condition a bar display may not advance for several minutes please be patient e f you press MENU during search channel search will stop NOTE e Memorizing channels is best accomplished during evening PRIMETIME hours as more stations are broadcasting digital signals Memorizing channels can only be accomplished while a station is broadcasting a digital signal to set that channel into memory e f you are unsure of the digital channels available in your area
44. to perform safety checks to determine that the unit is in proper operating condition 22 When you connect the product to other equipment turn off the power and unplug all of the equipment from the wall outlet Failure to do so may cause an electric shock and serious personal injury Read the owner s manual of the other equipment carefully and follow the instructions when making any connections 23 Sudden high volume sound may cause hearing or speaker damage When you use headphones if the unit is equipped with a headphone jack keep the volume at a moderate level If you use headphones continuously with high volume sound it may cause hearing damage 24 Do not allow the product to output distorted sound for an extended period of time It may cause speaker overheating and fire 25 This reminder is provided to call the cable TV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical 26 The socket outlet must be installed near the unit and easily accessible CHILD SAFETY It Makes A Difference How and Where You Use Your Flat Panel Display Congratulations on your purchase As you enjoy your new product please keep these safety tips in mind THE ISSUE The home theater entertainment experience is a growing trend and larger fla
45. ty stereo sound MTS also can transmit a second audio SEO SRE Mono program SAP containing a second language or other audio information This item is valid only when the analog broadcast Audio Language When two or more audio languages are included in a digital English French Spanish French Spanish signal you can select one of the audio language This English French Spanish ion is available only for digital broadcast Digital Audio Output Select the format for your digital audio output If you have Raw Raw ON PCM Off PCM connected an amplifier receiver to the digital audio jack on Ct AT TV The dynamic presence and sound created offers a thoroughly Off On enjoyable listening experience Auto Volume Volume level can be adjusted automatically by the sound Off On level Sleep Timer Sleep Timer switches the TV to standby after a defined Off 5 10 15 30 60 90 period of time 120 180 240 min To cancel the Sleep Timer set to Off Time Zone Select your local time zone for auto clock feature You can select Newfoundland Atlantic Eastern Central Mountain Pacific Alaska Hawaii and Samoa If you want to activate the daylight saving time select On M ES The Auto Clock function will automatically set the built in Off On clock Year Month Day and Time when the TV is connected to an antenna or cable TV system and it is turned off As the TV searches for a receivable station in your area and it rece
46. used by customer abuse misuse negligence or failure to follow operating instructions provided with the product d Ordinary adjustments to the product which can be performed by customer as outlined in the owners manual e Signal reception problems caused by external antenna or cable systems THIS WARRANTY IS NON TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER AND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT ANY APPLICABLE IMPLIED WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY ARE LIMITED IN DURATION TO A PERIOD OF THE EXPRESS WARRANTY AS PROVIDED HEREIN BEGINNING WITH THE DATE OF ORIGINAL PURCHASE AT RETAIL AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED SHALL APPLY TO THIS PRODUCT THEREAFTER ORION MAKES NO WARRANTY AS TO THE FITNESS OF THE PRODUCT FOR ANY PARTICULAR PURPOSE AND USE UNDER NO CIRCUMSTANCES SHALL ORION BE LIABLE FOR ANY LOSS DIRECT INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OF THIS PRODUCT THIS WARRANTY IS VALID ONLY IN THE UNITED STATES OF AMERICA THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS HOWEVER YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE SOME STATES DO NOT ALLOW LIMITATION ON IMPLIED WARRANTIES OR EXCLUSION OF CONSEQUENTIAL DAMAGE THEREFORE THESE RESTRICTIONS MAY NOT APPLY TO YOU ORION SALES INC 3471 N UNION DR OLNEY ILLINOIS 62450
47. will return to normal TV operation automatically SLEEP To set the TV to turn off after a preset amount of time press SLEEP on the remote control The clock will change for each press of the SLEEP button Off 5 min 10 min 240 min To confirm the sleep timer setting press SLEEP and the remaining time will be displayed for a few seconds To cancel the sleep timer press SLEEP repeatedly until the display turns to Off Quick guide for menu operation Call menu and for example Select Language 1 Press INPUT SELECT to select TV mode 2 Press MENU The TV menu screen will appear Picture 0 Picture Preference Standard Color Temperature Advanced Settings 3 Press lt or to select Setup then press V 4 Press a or Y to select Language then press lt or gt to select the desired language on the following pages the menu can be called in the same way as here 5 Press MENU to return to the previous screen NOTE e If no buttons are pressed for more than about 30 depending on your setting seconds the menu screen will return to normal operation automatically e During TV or external input mode except PC input mode if there is no signal reception the TV will change to standby after approx 15 minutes in PC input mode 1 minute Convenience functions You can change the default settings by pressing the MENU button on your remote then select the one of the icons at the top of
48. y for any damage to the ground Features Integrated Digital Tuner You can view digital broadcasts without using a Digital TV Set Top Box Closed Caption Decoder With Full Text Mode Displays text captions or full screen text on the screen for hearing impaired viewers Picture Adjustments Using The Remote Control The On Screen display allows precise remote control adjustment of BRIGHTNESS CONTRAST COLOR TINT and SHARPNESS Programmable TV Sleep Timer Operable from the remote control the TV can be programmed for up to 240 minutes to turn off automatically V Chip The V Chip function can read the rating of a broadcast program or movie content if the program is encoded with this information V Chip will allow you to set a restriction level Digital Audio Jack Coaxial When a component with a built in Dolby Digital decoder is connected Dolby Digital sound can produce the effect of being in a movie theater or a concert hall HDMI Component Video Jacks A VCR DVD player satellite receiver or other audio video component can be connected to this unit On Screen 3 Languages Display You can select one of 3 languages English French or Spanish for on screen programming Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LL
49. you may visit www antennaweb org to receive a list based on your address or zip code Should you require further assistance you may call our toll free customer service line at 1 800 289 0980 e New digital channels may be added to your area periodically it is recommended to perform the Automatic Search procedure regularly 3 The new channel will be added into the channel memory Show Hide channel You can select the channel that you want to skip 1 Select Channel Show Hide then press or ENTER 2 Press A or y to select the channel that you want to skip ga Sound Time Setup Lock Channel Channel Channel Label 7 0 12 0 23 2 23 3 23 77 23 999 Press ENTER to assign v mark for unwanted channel Repeat steps 2 3 for other channels you want to show hide Labeling channels Channel label appear with the channel number display each time you turn on the TV select a channel or press DISPLAY You can choose any 7 characters to identify a channel To create channel labels 1 Select Channel Channel Number 2 Press lt or gt to select a channel you want to label then press wv to select Channel Label Then press gt or ENTER 20 8 8 re Air Cable Cable Automatic Search Channel List Show Hide Channel Number Channel Label 3 Press A or V repeatedly until the character you want appears in the first space gt a e Sound Time Setup Lock Channel Hel
Download Pdf Manuals
Related Search