Home

Hunter Stonington - 46"

1. For Your Records and o Warranty Assistance 10 e VA S For reference also attach your receipt or a copy J j INA e J F E TAT A M a of your receipt to the manual Owner s Guide and Installation Manual SINCE 1886 a Form 4267 1 01 20100527 2010 Hunter Fan Co Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts Preparing the Fan Site e To reduce the risk of personal injury attach the fan directly to the 1 Getting Ready support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the 4 Wiring the Fan outlet box and associated wall switch location If you cannot lock 5 In
2. normal operation e The fan blades are at least 7 feet above the floor and the ceiling is at least 8 feet high e The fan blades have no obstructions to airflow such as walls or posts within 30 inches of the fan blade tips e The fan is directly below a joist or support brace that will hold the outlet box and the full weight of the fan Checklist for Existing Fan Site 30 From Wall or Nearest Obstruction 7 Minimum Blades to Floor 8 Minimum If you want to use an existing fan site complete the following checklist to Fan Support determine if the site is acceptable and safe for your new Hunter fan If you cannot check off every item prepare a new fan site as described on this page Fan Support System e Fan attaches directly to building structure e Fan support system will hold full weight of the fan and light kit Ceiling Hole The outlet box clearance hole is directly below the joist or support brace Outlet Box e The outlet box is an UL approved octagonal 4 x 1 1 2 outlet box or as specified by the support brace manufacturer e The outlet box is secured to the joist or support brace by wood screws and washers through the inner holes of outlet box The outer holes of the outlet box are aligned with joist or support brace e The bottom of the outlet box is recessed a minimum of 1 16 into ceiling Wiring e The electrical cable is secured to outlet box by an approved connector e Si
3. Assembly Upper Screw Switch Housing Steps 7 5 7 6 42671 01 05 27 10 Hunter Fan Company Lower Switch Housing Housing Assembly Screw Plug Connector Plug Connector Detail 7 Completing Your Installation With a Multi Staked Light Fixture Continued 7 6 To install the glass shades Insert each glass shade in a shade cup 7 7 Install and tighten the three thumb screws Do not overtighten 7 8 Install included 14w CFL bulbs Note Glass shade style and number of lights may vary Shade Cup Glass Shade Step 7 7 7 8 Thumb Screw 13 42671 01 05 27 10 Hunter Fan Company K2 8 Operating and Cleaning Your Ceiling Fan 8 1 Turn on electrical power to the fan 8 2 The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector 8 3 The light pull chain controls power to the light The pull chain has In warm weather use two settings On and Off downward air flow pattern 8 4 Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having
4. the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft 8 5 The blades on this fan have been treated with Hunter s Dust Armor protection making the blades less likely to attract dust and dirt Use a dry or slightly damp lint free cloth to clean the blades Do not use a furniture polish or any other cleaners that leave any residue as they will damage the protective Dust Armor on the blades 8 6 For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust In cold weather use upward using a mild detergent and a slightly dampened cloth You may air flow pattern use an artistic agent but To Change Airflow Direction never abrasive Turn the fan off and let it come to a complete cleaning agents stop Slide the reversing switch on the fan to the as they will opposite position Restart fan damage the Reversing finish Switch 14 42671 01 05 27 10 Hunter Fan Company 9 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that th
5. Connect the bare or green ground wire grounding from the ceiling to the green ground wire grounding from the ceiling plate and the green ground wire from the fan or the green ground wire on the low profile washer if you chose the low profile option Connect the white wire grounded from the ceiling to the white wire grounded from the fan Connect the remaining wires as follows Dual Switch Wiring e The black wire ungrounded from the ceiling to the black wire ungrounded from the fan e The black white wire ungrounded from the fan to the wire ungrounded for the wall switch Single Switch Wiring e The black wire ungrounded from the ceiling to the black ungrounded and the black white wire ungrounded from the fan A CAUTION Be sure no bare wire or wire strands are visible after making connections Turn the splices upward and push them carefully back through the ceiling plate into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box 9 ea Wire Connector OV A Jinx Dual Switch Wiring Wo Single Switch Wiring nem i ana 42671 01 05 27 10 Hunter Fan Company 5 Installing the Canopy and Canopy Trim Ring A WARNING Failure to complete th
6. ades and blade irons if applicable in sets as they were shipped 42671 01 05 27 10 Hunter Fan Company K2 2 Installing the Ceiling Plate A CAUTION To avoid possible electrical shock before installing your fan werd disconnect the power by turning off the circuit breakers to the outlet box Ceiling Peak and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter For Angled Ceilings Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak For Angled Ceilings Be sure to orient Ea the ceiling plate so that the two tabs 2 2 Your fan comes with four preinstalled noise isolators Check to are pointing toward the ceiling peak make sure all four isolators are in place and were not removed during shipment 2 3 Place a flat washer on each of the two 3 wood screws 2 4 Thread the supply wires from the outlet box in the ceiling through the hole in the center of the ceiling plate 2 5 Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be
7. e switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade assembly screws and blade iron armature screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated Problem Lights turn off when installed or dim when turned on 1 Check to make sure the wattage and type of light bulbs installed match the specifications on the light socket Problem Lights shut off suddenly 1 Turn the power to the fan off at the wall switch Wait 30 seconds then resume power to the fan If you need parts or service assistance please call 888 830 1326 In Canada call 866 268 1936 or visit us at our Web site at http www hunterfan com Hunter Fan Company 7130 Goodlett Farms Parkway 400 Memphis Tennessee 38016 42671 01 05 27 10 Hunter Fan Company
8. e following steps could cause the fan to fall Note It is recommended you use a magnetic tip screwdriver for the following steps 5 1 5 4 22 Rotate the hanger ball so the tab in the canopy is secure in the hanger ball groove Note Your fan may have multiple tabs and grooves that must be aligned Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate A WARNING The slots in the canopy must remain engaged while swinging the canopy for alignment Holding the canopy up with the screw holes aligned partially install two canopy screws into the holes opposite the ceiling plate tabs Partially install a canopy screw into the hole between the two ceiling plate tabs When all the holes are properly aligned securely tighten all three canopy screws Verify that the tabs in the canopy are still in the grooves of the hanger ball Align the tabs on the trim ring opposite the grooves in the hanger ball Using both hands push the canopy trim ring up to the top of the canopy The canopy trim ring will snap and lock into place Note Should you need to remove the trim ring press firmly on opposite sides of the trim ring directly above the groove in the hanger ball The tabs will flex out releasing the canopy trim ring 10 Step 5 1 Step 5 2 Step 5 3 Canopy gt Canopy Trim Canopy Screw 42671 01 05 27 10 Hunte
9. flush against the ceiling 2 6 Pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Wood Steps 2 3 2 6 Screw a 7 42671 01 05 27 10 Hunter Fan Company 3 Assembling and Hanging the Fan A WARNING Fan may fall if not assembled as directed in these installation instructions 3 1 Unbundle the wires from the fan For Standard or Angled mounting 3 2 Insert the downrod through the canopy and canopy trim ring Feed the wires from the fan through the downrod on one side of the pin in the ball 3 3 Loosen the square head setscrew on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the setscrew with a wrench or pliers Skip to step 3 7 A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod For Low Profile mounting Note For low profile mounting the downrod is replaced with the low profile washer 3 4 Remove the setscrew from the adapter 3 5 Place the low profile washer into the canopy with the lip down 3 6 Align the holes in the washer with
10. ith the joist or support brace 4 3 Drill pilot holes no larger than the minor diameter of the wood screws 5 64 through the inner holes of the outlet box 4 4 Attach the outlet box directly to the support brace or joist with two 8 x 1 1 2 wood screws and washers Th e bottom of the outlet box must be recessed a minimum of 1 16 into the ceiling Step 5 Prepare the Wiring 5 1 Make sure the circuit breakers to the fan supply line leads and associated wall switch location are turned off If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 5 2 Thread the fan supply line through the outlet box so that the fan supply line extends at least 6 beyond the box 5 3 Attach the fan supply line to the outlet box with an approved connector available at any hardware store or electrical supply house 5 4 Make certain the wiring meets all national and local standards and ANSI NFPA 70 You have now successfully prepared your ceiling fan site For instructions to install your ceiling fan go to your fan manual and continue with Section 2 Installing the Ceiling Plate J 42671 01 05 27 10 Hunter Fan Company A CAUTION All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Installer s Choice and Op
11. ngled ceiling ceiling recommended for ceilings less than 8 feet high 5 42671 01 05 27 10 Hunter Fan Company l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 6 Installing Multiple Fans If you are installing more than one fan keep the fan bl
12. r Fan Company 6 Assembling the Blades Step 6 1 Detail Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 Remove the blade mounting screws and rubber shipping bumpers from the motor Note Some blade mounting screws are installed in the motor to secure shipping blocks 6 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Steps 6 1 6 2 Note The blades on this fan have been treated with Hunter s Dust Armor protection making a ee the blades less likely to attract dust and dirt b Tai a Use adry or slightly damp lint free cloth to Se _ clean the blades Do not use a furniture polish 7 or any other cleaners that leave any residue as iE they will damage the protective Dust Armor on the blades Step 6 4 Use with grommet Blade Assembly Screws i Blade Mounting Use without grommet Screw lI 42671 01 05 27 10 Hunter Fan Company A 7 3 7 4 7 Completing You
13. r Installation With a Multi Staked Light Fixture A WARNING Use only the light fixture supplied with this fan model To attach the upper switch housing partially install two 6 32 x 3 8 housing assembly screws into the switch housing mounting plate Align the keyhole slots in the housing with the housing assembly screws Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots Install the remaining 6 32 x 3 8 screw into the housing Tighten all three screws firmly A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing fixture falling To attach the lower switch housing connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three 6 32 x 3 8 housing assembly screws 12 Steps 7 1 7 3 Housing
14. stalling the Canopy and Canopy the circuit breakers in the off position securely fasten a prominent Trim Ring warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a Solid state speed control with this fan Use only Hunter speed controls This product conforms to UL STD 507 and is certified to STD C22 2 No 113 e Wash your hands after your fan installation is complete Table Of Contents 2 Installing the Ceiling Plate 3 e Assembling and Hanging the Fan 8 6 Assembling the Blades 7 Completing Your Installation With a Multi Staked Light Fixture 8 Operating and Cleaning Your Ceiling Fan 9 Troubleshooting 2010 Hunter Fan Company 2 42671 01 05 27 10 Hunter Fan Company Preparing the Fan Site Step 1 Choose the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings Choose a fan site where e No object can come in contact with the rotating fan blades during
15. the holes in the adapter Assemble securely with three low profile screws Hanging the Fan Note To hang the fan you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks 3 7 Raise the fan and align the slots in the canopy with the hooks on the ceiling plate 3 8 Place the slots over the hooks to hang the fan 8 Standard or Angled Mounting Steps 3 2 3 3 9 mm Downrod lt Canopy lt Canopy Trim Ring Setscrew d Low Profile Mounting Steps 3 5 3 6 Low Profile Screws E T Fa nA Ground aster Wire Canopy Trim Ring a in Low Profile Screw Step 3 6 Detail Adapter Low Profile Screw Low Profile Washer 42671 01 05 27 10 Hunter Fan Company 4 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 Before attempting installation make sure the power is still off 4 2 To connect the wires hold the bare metal leads together and place 4 3 4 5 4 7 a wire connector over them then twist clockwise until tight For all these connections use the wire connectors provided
16. tional Accessories Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angled mounting The steps in this manual include Support Brace Ceili f j Standard m Box instructions for all three Installer s Choice mounting methods Mounting gt Style Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum Standard Mounting hangs from the performance of your Hunter fan use only Hunter speed controls ceiling by a downrod included For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Support Brace A CAUTION To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied Low Profile ad Mounting Style Outlet Box Angled Mounting recommended for a Low Profile Mounting fits close to the vaulted or a
17. x inches of lead wires extend from outlet box Fan Support System Outlet Box If your existing fan site is suitable skip ahead to Section 2 Installing the Ceiling Plate 3 42671 01 05 27 10 Hunter Fan Company Ceiling Height Preparing the Fan Site continued Step 2 Cut the Ceiling Hole 2 1 Locate the site for the ceiling hole directly below the joist or support brace that will hold the outlet box and fan 2 2 Cut a 4 diameter hole through the drywall or plaster of the ceiling You will use the hole to install the support brace and outlet box Step 3 Install a Support Brace If Necessary Determine if there is a ceiling joist directly above the ceiling hole If the joist is there determine if it is positioned to allow you to recess the outlet box a minimum of 1 16 into the ceiling If NOT install a support brace as follows 3 1 Attach a 2 x 4 support brace between two joists Position it to allow you to recess the bottom of the outlet box a minimum of 1 16 into the ceiling 3 2 Check the support brace to ensure it will support the full weight of the fan and light kit Step 4 Install the Outlet Box 4 1 Obtain a UL approved octagonal 4 x 1 1 2 outlet box plus two 8 x 1 1 2 wood screws and washers available from any hardware store or electrical supply house 4 2 Orient the outlet box so that both the inner and outer holes in the box align w

Hunter Stonington - 46"

Contents

Download Pdf Manuals

Related Search

Related Contents

Hunter Stonington - 46&quot;

Contents

Download Pdf Manuals

Related Search

Related Contents

Hunter Stonington - 46"