Chief JSB2090B mounting kit
Contents
1. DIMENSIONS 9 252 4 7 12 81 3255 9 58 2434171 10 65 270 4 2 25 3 45 ias 63t 87 6 m L 7 87 0 80 4X 1 00 200 0 254 IF 420 7 87 23 50 200 0 107 500 596 8 442 4 10 85 DIMENSIONS INCHES l 275 6 MILLIMETERS LEGEND Tighten Fastener Open Ended Wrench Apretar elemento de fijaci n Llave de boca Befestigungsteil festziehen ES Gabelschl ssel Apertar fixador Chave de bocas Serrare il fissaggio O Chiave a punte aperte Bevestiging vastdraaien Steeksleutel Serrez les fixations Cl fourche Aflojar elemento de fijaci n Llave de cabeza hexagonal Befestigungsteil l sen Sechskantschl ssel Desapertar fixador Chave de cabeca sextavada Allentare il fissaggio O Chiave esagonale Bevestiging losdraaien Zeskantsleutel Desserrez les fixations Cl t te hexagonale JSB2090 Installation Instructions TOOLS REQUIRED FOR INSTALLATION a 1 8 included PARTS B 1 Shelf assembly J 1 1 8 D R 2 S Y 10 24 x 1 2 F 4 G 4 E 4 1 4 20 750x 344x 500 H 4 10 24 x4 Hook amp loop C 2 Clip Installation Instructions JSB2090 ASSEMBLY AND INSTALLATION NOTE The following procedure assumes that a Chief TS218 swing arm2. mount not included has already been installed following instructions included with the mount 1 Hook two clips C over top of display with long edge of clip on back of display See Figure 1 k Back of display Figure 1 2 Slide interface bracket A up from bottom along back of display ensuring that bottom of interface bracket hooks over square extension on back of display See Figure 2 3 Hang interface bracket onto studs at bottom of clips C See Figure 2 A Hook over extension bracket 4 Fasten interface bracket to clips using four 1 4 20 locknuts F See Figure 2 5 Attach display to swing arm by lining up and inserting four studs on interface bracket A into holes in swing arm See Figure 3 IMPORTANT If attaching to the Chief TS318 swing arm use four 750x 344x 500 spacers G on the mount studs before attaching the mount to the swing arm face 6 Fasten display to swing arm using four 10 24 locknuts E See Figure 3 1 Figure 3 7 Lift shelf assembly B up from below display and hook onto interface bracket A See Figure 4 Display with attached interface 7 bracket Hook shelf assembly Swing arm not shown for clarity Figure 2 Figure 4 JSB2090 Installation Instructions 12 Rem
3. or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the JSB2090 up to and including the display does not exceed 35 Ibs 15 9 kg WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors IMPORTANT The JSB2090 interface brackets are designed to be mounted to an already installed Chief TS218 swing arm SAVE THESE INSTRUCTIONS Installation Instructions JSB2090
4. INSTALLATION INSTRUCTIONS Interface Bracket and Shelf Assembly GCHIEF JSB2090 Our Mounts Your Vision JSB2090 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment
5. ove paper from hook and loop squares and place remote phone on shelf assembly pressing it against the hook and loop squares See Figure 7 8 Fasten shelf assembly to interface bracket using two 10 24 x 1 2 buttonhead screws D See Figure 5 es Remote phone Swing arm not shown for clarity Figure 7 Figure 5 9 Put hook and loop H squares together so there are 2 squares 10 Remove paper from one side of both of the squares 11 Attach hook and loop squares to top of shelf assembly B See Figure 6 ee Figure 6 Installation Instructions JSB2090 JSB2090 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002280 Rev00 2012 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 10 12 USA International Europe Asia Pacific p TI U gt 0 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 S
Download Pdf Manuals
Related Search