World Marketing of America Springfield
Contents
1. installed virtually anywhere in your home However when choosing a location for your new electric fireplace ensure that the general instructions are followed For best results install the electric fireplace out of direct sunlight CLEARANCE TO COMBUSTIBLES Back 0 Omm Sides 0 Omm Floor 0 0mm TOD m 24 610mm FO 36 915mm ELECTRICAL CONNECTION ELECTRICAL SPECIFICATIONS Voltage 120 VAC 60Hz Total Amps 11 3 Amps Total Watts 1500 Watts Heater Ratings 1400 Watts 4 596 10 A 15 AMP 120 Volt 60Hz circuit with a properly grounded outlet is required Preferably the heater will be on a dedicated circuit Other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation The unit comes standard with a 6 1828mm long three wire cord exiting from the rear of the fireplace Plan the installation to avoid the use of an extension cord If an extension cord must be used it must be a minimum 16 AWG three wire with grounding type plug connector and rated no less than 1900 Watts WARNING Electrical outlet wiring must comply with local building codes and all other applicable regulations to reduce the risk of fire electrical shock and injury WARNING Do not use this fireplace if any part of it has been under water Immediately call a qualified service technician to i2. CLEANING INSTRUCTIONS 11 INSTRUCTIONS FOR POWER 12 SPECIFICATIONS 12 REPLACEMENT PARTS LIST 13 IMPORTANT SAFETY INSTRUCTIONS PLEASE RETAIN THIS USER S GUIDE FOR FUTURE REFERENCE When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to person including following 1 Read all instructions before using this appliance 2 This fireplace is hot when in use To avoid burns do not let bare skin touch hot surfaces The grill directly in front of the heater outlet becomes hot during heater operation Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 feet from the front of the unit 3 CAUTION Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended 4 Always unplug heater when not in use 5 Do not operate any fireplaces with a damaged cord or plug or after the heater has malfunctioned or if the fireplace has been dropped or damaged in any manner Take the fireplace to a authorized service facility for examination electrical or mechanical adjustment or repair 6 Do not use outdoors 7 This fireplace is not intended for use in bathrooms laundry areas or similar indoor locations Never locate the fireplace where it may fall into a bathtub or other water container 8 Do not install the fireplace directly on c
3. Comfort Hia EF5528HKD Freestanding Electric Fireplace Installation Instructions and Homeowner s Manual WARNING IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY A FIRE MAY RESULT CAUSING PROPERTY DAMAGE PERSONAL INJURY OR LOSS OF LIFE Comfort Home Products Inc FOR YOUH SAFETY 12256 William Penn Hwy Suite A Huntingdon PA 16652 DO NOT STORE Made in China OR USE GASOLINE OR Printed in China OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE COMFORT GLOW PHONE NUMBER 814 643 1775 http www worldmkting com ANSI UL 1278 MOVABLE AND WALL OR CEILING HUNG ELECTRIC ROOM HEATERS INSTALLER DO NOT DISCARD THIS MANUAL LEAVE FOR HOME OWNER CUSTOMER PLEASE RETAIN THIS MANUAL FOR FUTURE USE TABLE OF CONTENTS PLEASE READ THE INSTALLATION amp OPERATIONS INSTRUCTIONS BEFORE USING THIS APPLIANCE IMPORTANT Read all instructions and warnings carefully before starting installation Failure to follow these instructions may result in a possible electric shock fire hazard and will void the warranty INSTALLATION INSTRUCTIONS GENERAL 3 LOCATING YOUR ELECTRIC FIREPLACE 4 CLEARANCE TO COMBUSTIBLES 4 ELECTRICAL CONNECTIONS 4 ELECTRICAL SPECIFICATIONS 4 ASSEMBLY INSTRUCTIONS 5 9 OPERATING INSTRUCTIONS ON OFF SWITCH 9 HEATER CONTROLS 10 INSTRUCTIONS FOR REMOTE CONTROLS 10 SERVICE INSTRUCTIONS REPLACING LIGHT BULBS 11 GLASS INFORMATION 11 MAINTENANCE OF MOTORS 11
4. arpet or a similar surface which may restrict air circulation beneath the unit 9 Do not run cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traffic areas and where it will not be tripped over 10 To disconnect fireplace turn controls to the off position and remove plug from outlet 11 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause electric shock fire or damage to the appliance 12 To prevent fire do not block air intakes or exhaust in any manner Do not use on soft surfaces such as a bed where openings may become blocked 13 CAUTION This appliance gets hot and it contains internal parts that could arc or spark Do not use it in areas where gasoline paint or flammable liquids are used or stored This electric fireplace should not be used as a drying rack for clothing Also do not have Christmas stockings or decorations hung on or near it 14 Do not modify this fireplace Use it only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons 15 Avoid the use of an extension cord because it may overheat and cause a fire hazard However if you must use an extension cord the cord shall be 16 AWG 1875 Watts 16 Do not burn wood or other materials in this fireplace 17 Do not strike fireplace glass 18 Always use a certified e
5. e BASE B using 4 KD SCREWS 2 screws for each side See Figure C Figure C otep 4 Attach 2 SMALL FRONT PANELS G to the UPPER FRONT PANEL E with 4 KD SCREWS 2 screws for each side See Figure D Figure D Step 5 Attach the UPPER FRONT PANEL E in between the upper section of the 2 FRONT PANELS D1 D2 with 2 KD SCREWS 1 screw for each side See Figure E Figure E Step 6 Place the LOWER FRONT PANEL F in between the lower section of 2 FRONT PANELS D1 D2 and attach with 2 KD SCREWS 1 screw for each side See figure F Figure F Step 7 Install the TOP PANEL A to the unit as shown and attach with 5 KD SCEWS See Figure G Figure G Step 8 Put the insert in place and install the insert to the mantel with 5 SHORT KD SCREWS and 3 mounting clips on upper side 2 mounting bracket on lower side See Figure H and l Figure H Figure I Step 9 Tighten all KD Screws OPERATING INSTRUCTIONS Once the fireplace heater insert has been properly installed and connected to a ground electrical outlet It is ready to operate Note Ensure the circuit breakers for the power supply are turned on The controls are located behind two small flapping doors on the upper front of firebox Push the lower end of the flapping door to reach controls Thermostat knob and flame dimmer is located on the left side while the power on off and heat setting switches are located on the right side Push th
6. e lower end of the flapping door to reach controls Q oO 0 O aan Main Power On Off 1 Main Power On Off Press this switch for main power The indicator light will turn on 2 ON OFF Press this button for turning on the insert PCB board power 3 FLAME Press this button to turn on the flame log Press this button again to turn off the flame Keep pressing down this button the flame log light will turn from bright to dim Release the button when the desired brightness is reached 4 750W Press this button to turn on the heater at 750W heating power 5 1500W Press this button to turn on the heater at 1500W heating power Meanwhile the 750W should be turned on first 6 Temperature Control The temperature dial on the left side is for temperature control which could automatically turn the heater on and off to maintain a comfort temperature Turn the thermostat dial to the right to increase the desired temperature and the left to lower it Once the room temperature reaches the desired temperature turn the thermostat dial counter clockwise until you hear a click Leave in this position to maintain the room temperature at its current setting Note When the Main Power On Off switch is turned OFF all other heater functions will stop even though the other switches may be in the ON position INSTRUCTIONS FOR REMOTE OPERATION Plug in your electric fireplace and turn on the Main Power On Off switch on the right side of the fro
7. lectrician should new circuits or outlets been required 19 Always use properly grounded fused and polarized outlets 20 Always use ground fault protection where required by electrical code 21 Always disconnect power before performing any cleaning maintenance or relocation of the fireplace 22 When transporting or sorting the fireplace and cord keep in a dry place free from excessive vibration and store so as to avoid damage 23 Do not plug this product into a receptacle controlled by a wall switch or dimmer 24 Do not exceed recommended bulb wattage Using a higher wattage bulb could create a fire hazard or cause damage to your electric fireplace 25 SAVE THESE INSTRUCTIONS WARNING Procedures and techniques which if not carefully followed will expose the user to the risk of serious injury illness or death WARNING Procedures and techniques which if not carefully followed will result in damage to the equipment or personal property or may cause personal injury WARNING This is a 1500 watt heater and parts become hot when in use Be sure to maintain a personal distance and keep any combustible material at least three 3 feet away from the front of the heater The area directly behind around and under the heater must be clear and free of any obstructions KEEP CHILDREN AND PETS AWAY FROM HEATER AND CONTROLS LOCATING YOUR ELECTRIC FIREPLACE Your new freestanding electric fireplace may be
8. n a fire causing property damage and personal injury MAINTENANCE OF MOTORS The motors used on both blower fan and flame simulator assembly are prelubricated for the extended warranty of the motor no further lubrication is required However periodic cleaning vacuuming of the fan heater unit is recommended CAUTION Even though the glass is safety glass it may break if bumped struck or dropped Care must be taken when handling the glass GLASS INFORMATION 1 Under no circumstances should this product be operated with missing or broken glass 2 Do not strike or slam the glass 3 Do not use abrasive cleaners to clean the glass CAUTION Wait until the unit has completely cooled before attempting any cleaning CLEANING To clean the unit first turn off controls on unit and unplug unit from power source To clean the glass door remove dust with clean dry cloth or to remove finger prints and other marks clean glass with clean damp cloth Do not use abrasive cleaners or spray liquids on glass door surfaces Metal and metal painted parts should be cleaned with clean damp cloth only Do not use abrasive cleaners or spray liquids on this surface INSTRUCTIONS FOR POWER This heater is for use on 120 volts only The cord has a plug as shown at A in the following figure An adapter as shown at C is available for connecting three blade grounding type plugs to two slot receptacles The green grounding lug extending from
9. nspect the fireplace and replace any part of the electrical system if necessary ASSEMBLY INSTRUCTIONS NOTE Acomplete electric fireplace heater should consist of two parts the wooden mantel and the fireplace heater each packed in a separate carton It is not recommended to use the fireplace heater without the wooden mantel Unpack the fireplace heater and mantel Remove all packing materials PARTS LIST A Top panel B Base panel C Side panel D1 Left front panel D2 Right front panel E Upper front panel F Lower front panel G Small front panel T Short KD screws U Mounting clips N wWwuoOPN PRP HB N H H V Mounting brackets W X Plastic connector UT W KD screws UT WARNING Make sure the fireplace INSERT controls are in the OFF position and the INSERT is NOT plugged in CAUTION Place a piece of cardboard or protective sheet on the floor in order to avoid scratching the decorative surface of your mantel during assembly Please DO NOT fully tighten the KD screws until all panels are assembled step 1 Attach all PLASTIC CONNECTORS X to the PANELS C D amp E as shown in Figure A 2 screws for each PLASTIC CONNECTORS Figure A 5 Step 2 Attach the SIDE PANEL C to the LEFT FRONT PANEL D1 and RIGHT FRONT PANEL D2 with 6 KD SCREWS 8 screws for each side See Figure B rd Figure B Step 3 Attach the LEFT and RIGHT SIDE PANELS C D amp G to th
10. nt panel It will beep once This means you have power and your remote is ready to operate your electric fireplace at i r sl j V S V LL Lu 2 3 Pod oO LL 1 ON OFF Press this button to turn on the power 2 FLAME Press this button to turn on the flame effect Keep pressing down this button the flame log light will turn from bright to dim Pressing this button again will turn off the flame 3 750W Button Press this button and the fireplace will work at 750W Pressing again will switch it off 4 1500W Button Press this button and the fireplace will work at 1500W Pressing again will switch It off 10 SERVICE INSTRUCTIONS WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire electrical shock or personal injury REPLACING LIGHT BULBS There are two 2 40W Type B 10 light bulb located under the log set bed Remove the front glass screen by unscrew the two screws on the top Then remove another two screws on the log ember Take out the ember to access dead bulbs CAUTION The bulb in your unit can become extremely hot Allow at least 15 minutes between turning off the unit and removing the light bulb to avoid hot bulb coming in contact with the skin Loosen and remove burnt out bulb and replace with 40 W Type B 10 bulb WARNING Do not exceed 40 Watts per light bulb Use of a higher rated bulb may result i
11. the adapter must be connected to a permanent ground such as a properly grounded outlet box The adapter should not be used if a three slot grounded receptacle is available WARNING Before servicing this heater be sure to unplug heater from wall outlet Do not only turn off heater from the main ON OFF switch be sure to unplug this heater Metal Screw Cover of Grounded Outlet Box Adapter Grounding pin a KON C Grounding means Adapter NOT permitted in Canada Under CZ22 2 No 0 Standard SPECIFICATIONS MODEL EF5528RKD VOLTAGE 120V 60HZ TOTAL AMPS 11 3 AMPS TOTAL WATTS 1500W HEATING RATINGS 1400W 5 10 DIMENSIONS INCHES H X W X D FIREPLACE 37 8 X 31 89 X 8 54 CARTON 25 6 X 35 1 X 10 9 12 REPLACEMENT PARTS LIST ITEM 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 DESCRIPTION Flame Screen Thermostat knob Firebox cabinet Front Louver Flapping Door Touch Pad Log Set Power Cord Plug Glass Screen Thermostat Control Device Hemote Handset PCB Board Flame Reflector Assembly Heater Assembly Blower Assembly Bulb Bulb Socket 13 OEM NDF 100NR 14 NDF 100NR 78 NDF 100NR 15 NDF 100NR 18 NDF 100NR 12 NDF 100R 88R NDF 100R 02 NDF 100NR 89 NDF 100NR 41 NDF 100NR 60 NDF 100NR 103 NDF 100NR 88 NDF 100NR 43 44 68 69 NDF 100NR 51 81 NDF 100NR 36 79 57 NDF 100NR 96 NDF 100NR 97
Download Pdf Manuals
Related Search